mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-10-19 13:41:03 +00:00
SoftFever
d849b30906
Fan speeds, the recommended nozzle temperature range, minimal purge and multi-tool ramming flow now take one value per extruder variant. Each single value is repeated for every variant the filament lists, so every preset loads exactly what it did before.
296 lines
4.6 KiB
JSON
296 lines
4.6 KiB
JSON
{
|
|
"type": "filament",
|
|
"name": "INSLOGIC PA6-66 @BBL P2S",
|
|
"inherits": "INSLOGIC PA6-66 @base",
|
|
"from": "system",
|
|
"setting_id": "UHHdgZgE7e8KR2GV",
|
|
"instantiation": "true",
|
|
"activate_air_filtration": [
|
|
"1",
|
|
"1"
|
|
],
|
|
"additional_cooling_fan_speed": [
|
|
"70",
|
|
"70"
|
|
],
|
|
"close_fan_the_first_x_layers": [
|
|
"1"
|
|
],
|
|
"close_additional_fan_first_x_layers": [
|
|
"3"
|
|
],
|
|
"complete_print_exhaust_fan_speed": [
|
|
"70",
|
|
"70"
|
|
],
|
|
"cool_plate_temp": [
|
|
"0"
|
|
],
|
|
"cool_plate_temp_initial_layer": [
|
|
"0"
|
|
],
|
|
"during_print_exhaust_fan_speed": [
|
|
"70",
|
|
"70"
|
|
],
|
|
"eng_plate_temp": [
|
|
"50"
|
|
],
|
|
"eng_plate_temp_initial_layer": [
|
|
"50"
|
|
],
|
|
"fan_cooling_layer_time": [
|
|
"20"
|
|
],
|
|
"fan_max_speed": [
|
|
"100",
|
|
"100"
|
|
],
|
|
"fan_min_speed": [
|
|
"60",
|
|
"60"
|
|
],
|
|
"filament_adaptive_volumetric_speed": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_extruder_compatibility": [
|
|
"0"
|
|
],
|
|
"filament_cooling_before_tower": [
|
|
"10",
|
|
"10"
|
|
],
|
|
"filament_preheat_temperature_delta": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_tower_interface_pre_extrusion_dist": [
|
|
"10"
|
|
],
|
|
"filament_tower_interface_pre_extrusion_length": [
|
|
"0"
|
|
],
|
|
"filament_tower_ironing_area": [
|
|
"4"
|
|
],
|
|
"filament_tower_interface_purge_volume": [
|
|
"20"
|
|
],
|
|
"filament_tower_interface_print_temp": [
|
|
"-1"
|
|
],
|
|
"filament_density": [
|
|
"1.10"
|
|
],
|
|
"filament_dev_ams_drying_ams_limitations": [
|
|
"1"
|
|
],
|
|
"filament_dev_ams_drying_heat_distortion_temperature": [
|
|
"90"
|
|
],
|
|
"filament_dev_ams_drying_temperature": [
|
|
"65",
|
|
"80",
|
|
"65",
|
|
"80"
|
|
],
|
|
"filament_dev_ams_drying_time": [
|
|
"12",
|
|
"12",
|
|
"12",
|
|
"12"
|
|
],
|
|
"filament_dev_chamber_drying_bed_temperature": [
|
|
"90.0"
|
|
],
|
|
"filament_dev_chamber_drying_time": [
|
|
"18"
|
|
],
|
|
"filament_dev_drying_cooling_temperature": [
|
|
"65"
|
|
],
|
|
"filament_dev_drying_softening_temperature": [
|
|
"85"
|
|
],
|
|
"filament_extruder_variant": [
|
|
"Direct Drive Standard",
|
|
"Direct Drive High Flow"
|
|
],
|
|
"filament_flow_ratio": [
|
|
"0.98",
|
|
"0.98"
|
|
],
|
|
"filament_flush_temp": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_flush_temp_fast": [
|
|
"0"
|
|
],
|
|
"filament_flush_volumetric_speed": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_is_support": [
|
|
"0"
|
|
],
|
|
"filament_max_volumetric_speed": [
|
|
"12",
|
|
"12"
|
|
],
|
|
"filament_minimal_purge_on_wipe_tower": [
|
|
"15",
|
|
"15"
|
|
],
|
|
"filament_pre_cooling_temperature": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_pre_cooling_temperature_nc": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_prime_volume": [
|
|
"45"
|
|
],
|
|
"filament_prime_volume_nc": [
|
|
"60"
|
|
],
|
|
"filament_printable": [
|
|
"3"
|
|
],
|
|
"filament_ramming_travel_time_nc": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_ramming_volumetric_speed": [
|
|
"-1",
|
|
"-1"
|
|
],
|
|
"filament_ramming_volumetric_speed_nc": [
|
|
"-1",
|
|
"-1"
|
|
],
|
|
"filament_scarf_seam_type": [
|
|
"none"
|
|
],
|
|
"filament_shrink": [
|
|
"100%"
|
|
],
|
|
"filament_soluble": [
|
|
"0"
|
|
],
|
|
"full_fan_speed_layer": [
|
|
"0"
|
|
],
|
|
"additional_fan_full_speed_layer": [
|
|
"0"
|
|
],
|
|
"filament_scarf_height": [
|
|
"10%"
|
|
],
|
|
"filament_scarf_gap": [
|
|
"0%"
|
|
],
|
|
"filament_scarf_length": [
|
|
"10"
|
|
],
|
|
"filament_ramming_travel_time": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"filament_retract_length_nc": [
|
|
"14",
|
|
"14"
|
|
],
|
|
"filament_change_length": [
|
|
"10"
|
|
],
|
|
"hot_plate_temp": [
|
|
"50"
|
|
],
|
|
"hot_plate_temp_initial_layer": [
|
|
"50"
|
|
],
|
|
"long_retractions_when_ec": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"nozzle_temperature": [
|
|
"255",
|
|
"255"
|
|
],
|
|
"nozzle_temperature_initial_layer": [
|
|
"255",
|
|
"255"
|
|
],
|
|
"nozzle_temperature_range_high": [
|
|
"280",
|
|
"280"
|
|
],
|
|
"nozzle_temperature_range_low": [
|
|
"250",
|
|
"250"
|
|
],
|
|
"overhang_fan_speed": [
|
|
"95"
|
|
],
|
|
"overhang_fan_threshold": [
|
|
"10%"
|
|
],
|
|
"reduce_fan_stop_start_freq": [
|
|
"0"
|
|
],
|
|
"required_nozzle_HRC": [
|
|
"3"
|
|
],
|
|
"retraction_distances_when_ec": [
|
|
"0",
|
|
"0"
|
|
],
|
|
"slow_down_for_layer_cooling": [
|
|
"1"
|
|
],
|
|
"slow_down_layer_time": [
|
|
"6"
|
|
],
|
|
"slow_down_min_speed": [
|
|
"10"
|
|
],
|
|
"supertack_plate_temp": [
|
|
"0"
|
|
],
|
|
"supertack_plate_temp_initial_layer": [
|
|
"0"
|
|
],
|
|
"temperature_vitrification": [
|
|
"74.2"
|
|
],
|
|
"textured_plate_temp": [
|
|
"50"
|
|
],
|
|
"textured_plate_temp_initial_layer": [
|
|
"50"
|
|
],
|
|
"volumetric_speed_coefficients": [
|
|
"0 0 0 0 0 0",
|
|
"0 0 0 0 0 0"
|
|
],
|
|
"filament_start_gcode": [
|
|
"; Filament gcode\nM145 P0 ; set airduct mode to cooling mode for cooling\nM106 P2 S255 ; turn on auxiliary fan for cooling\nM106 P3 S127 ; turn on chamber fan for cooling\nM1002 gcode_claim_action : 29\nM191 S0 ; wait for chamber temp\nM106 P2 S102 ; turn on chamber cooling fan\nM106 P10 S0 ; turn off left aux fan\nM142 P6 R30 S40 U0.3 V0.8 ; set PETG exhaust chamber autocooling\n"
|
|
],
|
|
"filament_end_gcode": [
|
|
"; filament end gcode \n\n"
|
|
],
|
|
"filament_adhesiveness_category": [
|
|
"400"
|
|
],
|
|
"idle_temperature": [
|
|
"0"
|
|
],
|
|
"compatible_printers": [
|
|
"Bambu Lab P2S 0.4 nozzle"
|
|
]
|
|
}
|