{
	"type": "filament",
	"name": "INSLOGIC PA6-66 @BBL P2S",
	"inherits": "INSLOGIC PA6-66 @base",
	"from": "system",
	"setting_id": "UHHdgZgE7e8KR2GV",
	"instantiation": "true",
	"activate_air_filtration": [
		"1",
		"1"
	],
	"additional_cooling_fan_speed": [
		"70",
		"70"
	],
	"close_fan_the_first_x_layers": [
		"1"
	],
	"close_additional_fan_first_x_layers": [
		"3"
	],
	"complete_print_exhaust_fan_speed": [
		"70",
		"70"
	],
	"cool_plate_temp": [
		"0"
	],
	"cool_plate_temp_initial_layer": [
		"0"
	],
	"during_print_exhaust_fan_speed": [
		"70",
		"70"
	],
	"eng_plate_temp": [
		"50"
	],
	"eng_plate_temp_initial_layer": [
		"50"
	],
	"fan_cooling_layer_time": [
		"20"
	],
	"fan_max_speed": [
		"100",
		"100"
	],
	"fan_min_speed": [
		"60",
		"60"
	],
	"filament_adaptive_volumetric_speed": [
		"0",
		"0"
	],
	"filament_extruder_compatibility": [
		"0"
	],
	"filament_cooling_before_tower": [
		"10",
		"10"
	],
	"filament_preheat_temperature_delta": [
		"0",
		"0"
	],
	"filament_tower_interface_pre_extrusion_dist": [
		"10"
	],
	"filament_tower_interface_pre_extrusion_length": [
		"0"
	],
	"filament_tower_ironing_area": [
		"4"
	],
	"filament_tower_interface_purge_volume": [
		"20"
	],
	"filament_tower_interface_print_temp": [
		"-1"
	],
	"filament_density": [
		"1.10"
	],
	"filament_dev_ams_drying_ams_limitations": [
		"1"
	],
	"filament_dev_ams_drying_heat_distortion_temperature": [
		"90"
	],
	"filament_dev_ams_drying_temperature": [
		"65",
		"80",
		"65",
		"80"
	],
	"filament_dev_ams_drying_time": [
		"12",
		"12",
		"12",
		"12"
	],
	"filament_dev_chamber_drying_bed_temperature": [
		"90.0"
	],
	"filament_dev_chamber_drying_time": [
		"18"
	],
	"filament_dev_drying_cooling_temperature": [
		"65"
	],
	"filament_dev_drying_softening_temperature": [
		"85"
	],
	"filament_extruder_variant": [
		"Direct Drive Standard",
		"Direct Drive High Flow"
	],
	"filament_flow_ratio": [
		"0.98",
		"0.98"
	],
	"filament_flush_temp": [
		"0",
		"0"
	],
	"filament_flush_temp_fast": [
		"0"
	],
	"filament_flush_volumetric_speed": [
		"0",
		"0"
	],
	"filament_is_support": [
		"0"
	],
	"filament_max_volumetric_speed": [
		"12",
		"12"
	],
	"filament_minimal_purge_on_wipe_tower": [
		"15",
		"15"
	],
	"filament_pre_cooling_temperature": [
		"0",
		"0"
	],
	"filament_pre_cooling_temperature_nc": [
		"0",
		"0"
	],
	"filament_prime_volume": [
		"45"
	],
	"filament_prime_volume_nc": [
		"60"
	],
	"filament_printable": [
		"3"
	],
	"filament_ramming_travel_time_nc": [
		"0",
		"0"
	],
	"filament_ramming_volumetric_speed": [
		"-1",
		"-1"
	],
	"filament_ramming_volumetric_speed_nc": [
		"-1",
		"-1"
	],
	"filament_scarf_seam_type": [
		"none"
	],
	"filament_shrink": [
		"100%"
	],
	"filament_soluble": [
		"0"
	],
	"full_fan_speed_layer": [
		"0"
	],
	"additional_fan_full_speed_layer": [
		"0"
	],
	"filament_scarf_height": [
		"10%"
	],
	"filament_scarf_gap": [
		"0%"
	],
	"filament_scarf_length": [
		"10"
	],
	"filament_ramming_travel_time": [
		"0",
		"0"
	],
	"filament_retract_length_nc": [
		"14",
		"14"
	],
	"filament_change_length": [
		"10"
	],
	"hot_plate_temp": [
		"50"
	],
	"hot_plate_temp_initial_layer": [
		"50"
	],
	"long_retractions_when_ec": [
		"0",
		"0"
	],
	"nozzle_temperature": [
		"255",
		"255"
	],
	"nozzle_temperature_initial_layer": [
		"255",
		"255"
	],
	"nozzle_temperature_range_high": [
		"280",
		"280"
	],
	"nozzle_temperature_range_low": [
		"250",
		"250"
	],
	"overhang_fan_speed": [
		"95"
	],
	"overhang_fan_threshold": [
		"10%"
	],
	"reduce_fan_stop_start_freq": [
		"0"
	],
	"required_nozzle_HRC": [
		"3"
	],
	"retraction_distances_when_ec": [
		"0",
		"0"
	],
	"slow_down_for_layer_cooling": [
		"1"
	],
	"slow_down_layer_time": [
		"6"
	],
	"slow_down_min_speed": [
		"10"
	],
	"supertack_plate_temp": [
		"0"
	],
	"supertack_plate_temp_initial_layer": [
		"0"
	],
	"temperature_vitrification": [
		"74.2"
	],
	"textured_plate_temp": [
		"50"
	],
	"textured_plate_temp_initial_layer": [
		"50"
	],
	"volumetric_speed_coefficients": [
		"0 0 0 0 0 0",
		"0 0 0 0 0 0"
	],
	"filament_start_gcode": [
		"; Filament gcode\nM145 P0 ; set airduct mode to cooling mode for cooling\nM106 P2 S255 ; turn on auxiliary fan for cooling\nM106 P3 S127 ; turn on chamber fan for cooling\nM1002 gcode_claim_action : 29\nM191 S0 ; wait for chamber temp\nM106 P2 S102 ; turn on chamber cooling fan\nM106 P10 S0 ; turn off left aux fan\nM142 P6 R30 S40 U0.3 V0.8 ; set PETG exhaust chamber autocooling\n"
	],
	"filament_end_gcode": [
		"; filament end gcode \n\n"
	],
	"filament_adhesiveness_category": [
		"400"
	],
	"idle_temperature": [
		"0"
	],
	"compatible_printers": [
		"Bambu Lab P2S 0.4 nozzle"
	]
}