Move the Cube with the Wipe Tower in the Profile Validator

The slice check centres its cube on the bed, puts the prime tower beside it, then pulls the tower alone inside the printable outline. On a bed too narrow for the estimated footprint that pull drags the tower back over the cube: Volumic EXO42 IDRE MIRROR MODE (189 mm wide, 87.6 mm estimate) logged "gcode path conflicts found between WipeTower and cube" in every run, and three ~105 mm beds were left with 0.15 to 3.3 mm of clearance. The cube and the tower's footprint are now pulled inside as one rigid pair, so the clearance between them is fixed by construction. A bed too small for the pair keeps the old placement, and presets that were never clamped keep their exact layout.
fix: update OrcaArena product URL (#15796 )
2026-09-21 16:02:37 +00:00 · 2026-09-21 18:45:16 +08:00 · 2026-09-21 09:53:13 +00:00 · 2026-09-21 17:13:44 +08:00 · 2026-09-21 17:09:05 +08:00 · 2026-09-21 16:53:16 +08:00
43 changed files with 125 additions and 69 deletions
@@ -529,7 +529,7 @@ jobs:
      && github.event_name == 'pull_request_target'
    permissions:
      contents: read
-      pull-requests: read
+      pull-requests: write
      issues: write
    runs-on: ubuntu-latest
    timeout-minutes: 5
@@ -636,7 +636,7 @@ jobs:
      && github.event_name == 'pull_request_target'
    permissions:
      contents: read        # delegatable subtree, for file modes
-      pull-requests: read
+      pull-requests: write
      issues: write         # label + comment
    runs-on: ubuntu-latest
    timeout-minutes: 10
@@ -1,6 +1,6 @@
 {
 	"name": "Creality",
-	"version": "02.03.02.82",
+	"version": "02.03.02.84",
 	"force_update": "0",
 	"description": "Creality configurations",
 	"machine_model_list": [
@@ -55,7 +55,7 @@
 		"0"
 	],
 	"filament_max_volumetric_speed": [
-		"12"
+		"8"
 	],
 	"filament_retract_before_wipe": [
 		"100"
@@ -43,19 +43,19 @@
 		"1.75"
 	],
 	"filament_flow_ratio": [
-		"0.98"
+		"0.95"
 	],
 	"filament_is_support": [
 		"0"
 	],
 	"filament_max_volumetric_speed": [
-		"16"
+		"14"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
 	],
 	"filament_retract_before_wipe": [
-		"nil"
+		"100%"
 	],
 	"filament_retract_restart_extra": [
 		"nil"
@@ -67,7 +67,7 @@
 		"nil"
 	],
 	"filament_retraction_minimum_travel": [
-		"nil"
+		"2"
 	],
 	"filament_retraction_speed": [
 		"nil"
@@ -106,7 +106,10 @@
 		"0"
 	],
 	"slow_down_layer_time": [
-		"8"
+		"14"
+	],
+	"slow_down_min_speed": [
+		"20"
 	],
 	"temperature_vitrification": [
 		"110"
@@ -118,7 +121,7 @@
 		"55"
 	],
 	"filament_start_gcode": [
-		"; Filament gcode\n"
+		";filament start gcode\n"
 	],
 	"filament_end_gcode": [
 		"; filament end gcode \n"
@@ -153,7 +156,7 @@
 	"filament_unloading_speed_start": "100",
 	"material_flow_dependent_temperature": "0",
 	"material_flow_temp_graph": "[[0.2,210],[0.6,220]]",
-	"pressure_advance": "0.12",
+	"pressure_advance": "0.032",
 	"support_material_interface_fan_speed": "-1",
 	"compatible_printers": [
 		"Creality SPARKX i7 0.2 nozzle",
@@ -54,7 +54,7 @@
 	"machine_min_travel_rate": "0,0",
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "0",
-	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM104 S[nozzle_temperature_initial_layer]\nM204 S2000\nG1 Z3 F600\nM83\nG1 X20 Y-1 F30000\nG1 Z0.3 F1200\nG1 X100 E10  F{filament_max_volumetric_speed[initial_extruder]/0.3*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X120 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X125 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X1 Z-0.300\nG1 X4\nG92 E0\nG1 Z1 F1200",
+	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM109 S[nozzle_temperature_initial_layer]\nM204 S2000\nG1 Z3 F600\nM83\nG1 X20 Y-1 F30000\nG1 Z0.3 F1200\nG1 X100 E10  F{filament_max_volumetric_speed[initial_extruder]/0.3*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X120 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X125 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X1 Z-0.300\nG1 X4\nG92 E0\nG1 Z1 F1200",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -123,7 +123,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -123,7 +123,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -123,7 +123,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA HF @Creality"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -56,7 +56,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
 	"machine_ptc_exist": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -123,7 +123,7 @@
 	"default_filament_profile": [
 		"Generic PLA @Creality K1-all"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails_format": "PNG",
@@ -57,7 +57,7 @@
 	"machine_min_travel_rate": "0,0",
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -57,7 +57,7 @@
 	"machine_min_travel_rate": "0,0",
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -55,7 +55,7 @@
 	"machine_min_travel_rate": "0,0",
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA @Creality K1-all"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA @Creality K1-all"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -124,7 +124,7 @@
 	"default_filament_profile": [
 		"Generic PLA @Creality K1-all"
 	],
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_end_gcode": "END_PRINT",
 	"scan_first_layer": "0",
 	"thumbnails": [
@@ -56,7 +56,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
 	"machine_ptc_exist": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -57,7 +57,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "1",
 	"machine_ptc_exist": "1",
-	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
+	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM109 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
 	"machine_unload_filament_time": "0",
 	"manual_filament_change": "0",
 	"nozzle_hrc": "0",
@@ -59,7 +59,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "0",
 	"machine_ptc_exist": "0",
-	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM104 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
+	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM109 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
 	"machine_tool_change_time": "0",
 	"machine_unload_filament_time": "30",
 	"manual_filament_change": "0",
@@ -59,7 +59,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "0",
 	"machine_ptc_exist": "0",
-	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM104 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
+	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM109 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
 	"machine_tool_change_time": "0",
 	"machine_unload_filament_time": "30",
 	"manual_filament_change": "0",
@@ -59,7 +59,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "0",
 	"machine_ptc_exist": "0",
-	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM104 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
+	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM109 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
 	"machine_tool_change_time": "0",
 	"machine_unload_filament_time": "30",
 	"manual_filament_change": "0",
@@ -59,7 +59,7 @@
 	"machine_pause_gcode": "PAUSE",
 	"machine_platform_motion_enable": "0",
 	"machine_ptc_exist": "0",
-	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM104 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
+	"machine_start_gcode": "M140 S0\nM104 S0 \nSTART_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nM83 \nM8200 P S[initial_no_support_extruder]\nM220 S100\n\nSET_VELOCITY_LIMIT ACCEL=5000 ACCEL_TO_DECEL=5000\nG0 X267 F18000 \nG0 X278 F2400\nM109 S[nozzle_temperature_initial_layer]\nM106 S0\nT[initial_no_support_extruder]\n\nM8200 O\nM204 S2000\nG1 Z3 F600\nM83\nG1 Y0 F12000\nG1 X150 F30000\nG1 Z0.2 F600\nG1 X120 Y0 E15 F{filament_max_volumetric_speed[initial_extruder]/0.3*60*0.1}\nG1 X115 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X110 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X105 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG1 X100 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)*60}\nG1 X95 E.3742  F{outer_wall_volumetric_speed/(0.3*0.5)/4*60}\nG91\nG1 X-1 Z-0.3\nG1 X-4\nG92 E0",
 	"machine_tool_change_time": "0",
 	"machine_unload_filament_time": "30",
 	"manual_filament_change": "0",
@@ -1,7 +1,7 @@
 {
 	"name": "Orca Arena Printer",
 	"url": "",
-	"version": "02.04.00.05",
+	"version": "02.04.00.06",
 	"force_update": "0",
 	"description": "Orca Arena configuration files",
 	"machine_model_list": [
@@ -2,7 +2,7 @@
 	"type": "machine_model",
 	"name": "Orca Arena X1 Carbon",
 	"model_id": "orca_arena_x1c",
-	"url": "",
+	"url": "https://www.orcaslicer.com",
 	"nozzle_diameter": "0.4;0.2;0.6;0.8",
 	"machine_tech": "FFF",
 	"family": "ARENA-3DP",
@@ -1,6 +1,6 @@
 {
 	"name": "OrcaFilamentLibrary",
-	"version": "02.04.00.08",
+	"version": "02.04.00.09",
 	"force_update": "0",
 	"description": "Orca Filament Library",
 	"filament_list": [
@@ -3,6 +3,7 @@
 	"name": "DREMC ABS @System",
 	"inherits": "DREMC ABS @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "gNjISMxTLwQzDrV9",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC ABS+ @System",
 	"inherits": "DREMC ABS+ @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "M73sIwcpWv6zpFrb",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC ASA @System",
 	"inherits": "DREMC ASA @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "PMulSQ0tYbNyvOYw",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC ASA CF @System",
 	"inherits": "DREMC ASA CF @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "ZcipEKAqtBcAm6vR",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC ASA GF @System",
 	"inherits": "DREMC ASA GF @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "8J3lt7KlQWcx0VUS",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC PA12-CF @System",
 	"inherits": "DREMC PA12-CF @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "jVlZ1KPsA5i8RIED",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,6 +3,7 @@
 	"name": "DREMC PET-CF @System",
 	"inherits": "DREMC PET-CF @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "hal1nPyBF13UL9qB",
+	"instantiation": "true",
 	"compatible_printers": []
 }
@@ -3,7 +3,8 @@
 	"name": "DREMC PETG @System",
 	"inherits": "DREMC PETG @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "gTGiaBYfymmtlyfG",
+	"instantiation": "true",
 	"filament_max_volumetric_speed": [
 		"20"
 	],
@@ -1,9 +1,10 @@
 {
 	"type": "filament",
 	"name": "DREMC PLA+ HS @System",
-	"inherits": "DREMC PLA+ @base",
+	"inherits": "DREMC PLA+ HS @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "I0HWhYAZ3ppq91Gx",
+	"instantiation": "true",
 	"filament_max_volumetric_speed": [
 		"22"
 	],
@@ -3,7 +3,8 @@
 	"name": "DREMC PLA+ @System",
 	"inherits": "DREMC PLA+ @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "fIjHIsFmdDWIM1bf",
+	"instantiation": "true",
 	"filament_max_volumetric_speed": [
 		"18"
 	],
@@ -3,7 +3,8 @@
 	"name": "DREMC TPU 95A @System",
 	"inherits": "DREMC TPU 95A @base",
 	"from": "system",
-	"instantiation": "false",
+	"setting_id": "AfnFh14wKZsNEaZ1",
+	"instantiation": "true",
 	"filament_max_volumetric_speed": [
 		"6"
 	],
@@ -33,15 +33,15 @@
        "210"
    ],
    "hot_plate_temp": [
-        "60"
+        "50"
    ],
    "hot_plate_temp_initial_layer": [
-        "60"
+        "50"
    ],
    "textured_plate_temp": [
-        "60"
+        "50"
    ],
    "textured_plate_temp_initial_layer": [
-        "60"
+        "50"
    ]
 }
@@ -122,17 +122,19 @@ Vec2d printable_area_center(const DynamicPrintConfig &cfg)

 // Put the prime tower where the GUI and CLI would before slicing. The config default (x 15, y 220)
 // lies off any bed shallower than the tower, and generation rejects an off-plate tower instead of
-// exporting it. Beside the centred cube, clear of the edge exclusion strips some beds carry, then
-// pulled inside the printable outline by the tower's own estimated footprint, with a few mm of
-// clearance so the conflict checker never sees the two touch.
-void place_wipe_tower(DynamicPrintConfig &cfg, const Vec2d &center)
+// exporting it. Beside the cube at the bed centre, clear of the edge exclusion strips some beds
+// carry, with a few mm of clearance so the conflict checker never sees the two touch. The cube and
+// the tower's estimated footprint are then pulled inside the printable outline as one rigid pair:
+// moving the tower alone would push it back onto the cube on a narrow bed. Returns that move for
+// the cube.
+Vec2d place_wipe_tower(DynamicPrintConfig &cfg, const Vec2d &center)
 {
    const auto *area = cfg.option<ConfigOptionPoints>("printable_area");
    if (area == nullptr || area->values.size() < 3)
-        return;
+        return Vec2d::Zero();
    const WipeTowerFootprint footprint = estimate_wipe_tower_footprint(cfg, resolve_wipe_tower_type(cfg), {0, 1}, cfg.opt_float("layer_height"), 10.);
    if (footprint.depth < EPSILON)
-        return;
+        return Vec2d::Zero();
    const double margin = WIPE_TOWER_MARGIN + footprint.brim_width;
    // The position is the tower's own origin; a rotated tower extends from it in another
    // direction, so place the rotated box's extents rather than the origin.
@@ -143,13 +145,22 @@ void place_wipe_tower(DynamicPrintConfig &cfg, const Vec2d &center)
    const Vec2d       size  = unscale(local.max) - lo;
    Vec2d             pos(center.x() + 5. + margin + 5. - lo.x(), center.y() - size.y() / 2. - lo.y());
    box.translate(Point::new_scale(pos.x(), pos.y()));
-    const Vec2f move = WipeTower::move_box_inside_polygon(get_extents(box), Polygons{Polygon::new_scale(area->values)}, scaled<coord_t>(margin));
-    pos += move.cast<double>();
+    // A bed too small for the pair keeps the cube at its centre and places the tower alone.
+    const Polygons    bed{Polygon::new_scale(area->values)};
+    const BoundingBox tower = get_extents(box);
+    BoundingBox       pair  = tower;
+    pair.merge(Point::new_scale(center.x() - 5., center.y() - 5.));
+    pair.merge(Point::new_scale(center.x() + 5., center.y() + 5.));
+    const Point       room  = get_extents(bed).size() - Point::new_scale(2. * margin, 2. * margin);
+    const bool        rigid = pair.size().x() < room.x() && pair.size().y() < room.y();
+    const Vec2d       move  = WipeTower::move_box_inside_polygon(rigid ? pair : tower, bed, scaled<coord_t>(margin)).cast<double>();
+    pos += move;
    cfg.option<ConfigOptionFloats>("wipe_tower_x", true)->values = {pos.x()};
    cfg.option<ConfigOptionFloats>("wipe_tower_y", true)->values = {pos.y()};
+    return rigid ? move : Vec2d::Zero();
 }

-// Slice one centered cube that switches from filament 1 to filament 2 partway up, so exactly one
+// Slice one cube that switches from filament 1 to filament 2 partway up, so exactly one
 // filament change fires, then export. The change drives the printer's own change_filament_gcode: on a
 // single-nozzle machine it rides the AMS prime tower (append_tcr), on a multi-nozzle machine it routes
 // through the nozzle swap (set_extruder / append_tcr2) - the engine picks the path from the printer's
@@ -157,10 +168,10 @@ void place_wipe_tower(DynamicPrintConfig &cfg, const Vec2d &center)
 // Slic3r::PlaceholderParserError from export.
 std::string slice_two_color_cube_and_export(DynamicPrintConfig cfg, bool is_bbl)
 {
-    const Vec2d center = printable_area_center(cfg);
-    place_wipe_tower(cfg, center);
+    const Vec2d center   = printable_area_center(cfg);
+    const Vec2d cube_min = center - Vec2d(5., 5.) + place_wipe_tower(cfg, center);
    TriangleMesh m = make_cube(10, 10, 10);
-    m.translate(float(center.x() - 5.), float(center.y() - 5.), 0.f);
+    m.translate(static_cast<float>(cube_min.x()), static_cast<float>(cube_min.y()), 0.f);

    Model  model;
    Print  print;
@@ -8,6 +8,7 @@
 #include <boost/filesystem.hpp>

 #include <wx/event.h>
+#include <wx/uri.h>

 #include <utility>

@@ -55,6 +56,14 @@ wxString web_base_url()
    return wxString("file://") + from_u8(dir) + "/";
 }

+// Whether a loaded document is the plugin HTML's own base URL. The web view reports the URL it
+// parsed, so any fragment the page navigated to is ignored and the escaping it applies to what the
+// resources path holds (a space, a non-ASCII character) is undone first.
+bool is_content_url(const wxString& url)
+{
+    return wxURI::Unescape(url.BeforeFirst('#')) == web_base_url();
+}
+
 } // namespace

 PluginWebDialog::PluginWebDialog(wxWindow*          parent,
@@ -89,6 +98,7 @@ PluginWebDialog::PluginWebDialog(wxWindow*          parent,
        // missing/blocked bootstrap resource (e.g. a packaged build) still triggers it.
        Bind(wxEVT_WEBVIEW_LOADED, &PluginWebDialog::on_bootstrap_event, this, wv->GetId());
        Bind(wxEVT_WEBVIEW_ERROR, &PluginWebDialog::on_bootstrap_event, this, wv->GetId());
+        Bind(wxEVT_WEBVIEW_NAVIGATED, &PluginWebDialog::on_navigated, this, wv->GetId());
    }
    Bind(wxEVT_CLOSE_WINDOW, &PluginWebDialog::on_close_window, this);
 }
@@ -139,19 +149,37 @@ void PluginWebDialog::destroy_for_plugin(PluginWebDialog* dialog)

 void PluginWebDialog::on_bootstrap_event(wxWebViewEvent& event)
 {
-    // The first bootstrap load (or its error) triggers the swap to plugin HTML;
-    // the resulting plugin-page load is ignored (guarded by m_content_loaded).
-    load_plugin_content();
+    const bool loaded = event.GetEventType() == wxEVT_WEBVIEW_LOADED;
+    // The first bootstrap load (or its error) triggers the swap to plugin HTML.
+    if (!m_content_loaded)
+        load_plugin_content();
+    // WebKit reloads the SetPage base URL, so a committed load of it that we did not start is a reload.
+    // A failed navigation is reported against the page that stayed but never commits. Edge ignores the
+    // base URL and restores SetPage content itself, so nothing matches there.
+    else if (is_content_url(event.GetURL())) {
+        if (m_own_page_load)
+            m_own_page_load = false;
+        else if (loaded && m_content_navigated)
+            load_plugin_content();
+    }
+    if (loaded)
+        m_content_navigated = false;
+    event.Skip();
+}
+
+void PluginWebDialog::on_navigated(wxWebViewEvent& event)
+{
+    m_content_navigated = is_content_url(event.GetURL());
    event.Skip();
 }

 void PluginWebDialog::load_plugin_content()
 {
-    if (m_content_loaded)
-        return;
    m_content_loaded = true;
-    if (wxWebView* wv = browser())
+    if (wxWebView* wv = browser()) {
+        m_own_page_load = true;
        wv->SetPage(wxString::FromUTF8(m_html), web_base_url());
+    }
 }

 void PluginWebDialog::on_script_message(const nlohmann::json& payload)
@@ -64,6 +64,7 @@ protected:

 private:
    void on_bootstrap_event(wxWebViewEvent& event);
+    void on_navigated(wxWebViewEvent& event);
    void load_plugin_content();
    void on_close_window(wxCloseEvent& event);
    void fire_submit(const nlohmann::json& data);
@@ -72,6 +73,8 @@ private:

    std::string                   m_html;
    bool                          m_content_loaded{false};
+    bool                          m_own_page_load{false};   // a SetPage of the plugin HTML is in flight
+    bool                          m_content_navigated{false}; // a navigation to the base URL has committed
    bool                          m_open{true};
    bool                          m_close_fired{false};
    std::optional<nlohmann::json> m_result;
Author	SHA1	Message	Date
Hanif Koh	02b8e26a4f	Move the Cube with the Wipe Tower in the Profile Validator The slice check centres its cube on the bed, puts the prime tower beside it, then pulls the tower alone inside the printable outline. On a bed too narrow for the estimated footprint that pull drags the tower back over the cube: Volumic EXO42 IDRE MIRROR MODE (189 mm wide, 87.6 mm estimate) logged "gcode path conflicts found between WipeTower and cube" in every run, and three ~105 mm beds were left with 0.15 to 3.3 mm of clearance. The cube and the tower's footprint are now pulled inside as one rigid pair, so the clearance between them is fixed by construction. A bed too small for the pair keeps the old placement, and presets that were never clamped keep their exact layout.	2026-09-21 18:45:16 +08:00
barmanr	64cad00569	fix: update OrcaArena product URL (#15796 ) Merged by /bot merge on behalf of @barmanr (id 281100727). Grants: resources/profiles/OrcaArena, resources/profiles/OrcaArena.json Head: `794db5d30d`	2026-09-21 09:53:13 +00:00
SoftFever	45940a573d	Grant pull-requests write so profile PR labels and the partner notice actually post	2026-09-21 17:13:44 +08:00
HanifKoh	8b63628cf9	Restore Plugin HTML After a WebKit Reload (#15737 ) Plugin dialog content is injected with SetPage, so on the WebKit backends a reload (context menu, keyboard shortcut or location.reload()) re-fetches the SetPage base URL instead of the injected document, and the plugin UI is gone for good: load_plugin_content() returned early once m_content_loaded was set. Re-inject the plugin HTML when a main-frame load after the initial swap is neither that swap nor a page the plugin linked to. m_own_page_load marks the load our own SetPage caused, and the URL test recognises the reload: the injected document and the directory a reload re-fetches both report the base URL, so a load of any other URL is left alone. The test ignores a fragment the page navigated to, and undoes the escaping the web view applies to what the resources path holds. A load reaching the base URL is not enough on its own, because WebKitGTK reports a navigation that never committed against the document that stayed and then finishes that document again: a link to a missing file therefore arrives as a load of the base URL and reads exactly like a reload. So the re-injection also requires a navigation to the base URL to have committed, which a reload always does and a failure never does. A bootstrap page that cannot be loaded is still not recovered from: WebKitGTK substitutes a stock error page for it, and that load supersedes the swap whichever way the swap is ordered around it. The file ships, so this is a broken-install path; nothing here makes it worse than it already was. No separate MSW path is needed: wxWebViewEdge ignores the SetPage base URL, so its documents report about:blank and the test never matches there, and WebView2 reloads NavigateToString content from its own history entry anyway.	2026-09-21 17:09:05 +08:00
dremc	c8bfd2ad3e	Fix instantiation on DREMC Filament (#14659 )	2026-09-21 16:53:16 +08:00
Alexander Haibl	3eae4c6997	fix-start-gcode for many creality printers (#14652 )	2026-09-21 16:22:32 +08:00
gyarros	83eaf3bcfc	FilAr PLA-mate: lower bed temperature to 50 C (#14489 )	2026-09-21 16:07:49 +08:00
Davide Garberi	454ef1571b	Update generic filament profiles for Creality SPARKX i7 (#14388 )	2026-09-21 16:01:14 +08:00