Move the Cube with the Wipe Tower in the Profile Validator

The slice check centres its cube on the bed, puts the prime tower beside
it, then pulls the tower alone inside the printable outline. On a bed too
narrow for the estimated footprint that pull drags the tower back over
the cube: Volumic EXO42 IDRE MIRROR MODE (189 mm wide, 87.6 mm estimate)
logged "gcode path conflicts found between WipeTower and cube" in every
run, and three ~105 mm beds were left with 0.15 to 3.3 mm of clearance.

The cube and the tower's footprint are now pulled inside as one rigid
pair, so the clearance between them is fixed by construction. A bed too
small for the pair keeps the old placement, and presets that were never
clamped keep their exact layout.

.claude/skills/orca-profiles/SKILL.md

@@ -21,6 +21,7 @@ Paths below are relative to this skill. Commands run from the repository root.
 | Add a printer or nozzle; change models, variants, assets or extruder vectors | [machine-profiles.md](references/machine-profiles.md) |
 | Add a quality tier or tune a process | [process-profiles.md](references/process-profiles.md) |
 | Create a vendor bundle; diagnose loading or inheritance; migrate preset names | [vendor-bundle.md](references/vendor-bundle.md) |
+| Name a preset; check what a name must equal | [naming.md](references/naming.md) |
 | Change ids; diagnose AMS identity | [ids.md](references/ids.md), then `docs/HLSD/filament_id.md` for identity changes |
 | Review a profile diff | [review-checklist.md](references/review-checklist.md) |
 | Run checks, interpret failures, test another tree or verify in the app | [validation.md](references/validation.md) |
@@ -44,7 +45,10 @@ Paths below are relative to this skill. Commands run from the repository root.
    update in-tree references too. See [migration rules](references/vendor-bundle.md#renamed_from).
 6. **Compatibility uses exact printer variant names.** Every instantiated non-library filament
    needs a non-empty `compatible_printers` in its own file. Library fallbacks may omit it;
-   library printer-specific tunes use a non-empty list. Keep same-product tunes disjoint.
+   library printer-specific tunes use a non-empty list. One variant may be claimed by only one
+   profile per filament product (`filament_id`); an overlap is resolved by moving the variant to the
+   most specific preset, which is preferred over deleting a profile. See
+   [one variant, one profile](references/filament-profiles.md#overlapping-coverage-one-variant-one-profile-per-product).
 7. **Preset values are strings or arrays of strings.** Use `"instantiation": "false"`, not `false`.
    Model `nozzle_diameter` is a `;`-separated string; machine `nozzle_diameter` is an array.
    Wrong types can abort loading; see [failure scopes](references/vendor-bundle.md#failure-modes-ranked-by-blast-radius).
@@ -87,7 +91,8 @@ Paths below are relative to this skill. Commands run from the repository root.
    ```
 
    On Windows use `py -3` instead of `python3`, and `scripts\check_profile.bat -Vendor "<Vendor>"`
-   / `scripts\check_profile.bat`. Logs: `.test/check_profiles/logs/<check>.log`.
+   / `scripts\check_profile.bat`. Logs land in a per-user cache dir (see
+   [validation.md](references/validation.md)).
    Id checks remain tree-wide under `--vendor`; filament-only bundles skip the default slice check.
    See [validation.md](references/validation.md) for flags, coverage and error remedies.
 5. **Verify the changed behavior.** Slice newly added non-default processes explicitly, and

.claude/skills/orca-profiles/references/filament-profiles.md

@@ -103,6 +103,57 @@ name.
 - Copying a base's full printer list onto a nozzle-specific variant produces duplicate combobox entries —
   a real shipped bug twice over.
 
+## Overlapping coverage: one variant, one profile per product
+
+`filament_id` is the **product** key, not the preset key — every variant of one product shares it
+(`<filament_vendor>/<filament_type>/<name-before-@>`). So if one printer variant appears in the
+`compatible_printers` of two presets of that product, the slicer cannot tell them apart at AMS match time.
+The C++ validator reports `Ambiguous AMS filament match: N presets share filament_id "X" … printer "Y"`.
+`orca_profile_tool.py check` does **not** see it and passes. Resolve the overlap by **specificity**: keep
+the variant on the most specific profile and remove it from every more general one. Deleting a profile is
+the least preferred fix — moving coverage keeps the tune that users rely on.
+
+Judge specificity from the profile's `compatible_printers` — how many variants it actually covers — and
+use the name only as a secondary, easily-vague hint; decide by the lists, with a best judgement call on
+the name. Naming conventions differ by vendor: BBL's is the reference (`@<Vendor> <Model>` for a whole
+model, `@<Vendor> <Model> <nozzle> nozzle` for one variant, `@<Vendor>` for a vendor-wide generic), but
+others vary (`@<printer model>`, a printer serial, or Creality's `@<Model>-all`). A name never overrides
+the list — see [preset naming](naming.md) for the shapes.
+
+Specificity, most to least:
+
+1. **Variant-specialized** — lists a single printer variant (BBL-style
+   `... @<Vendor> <Model> <nozzle> nozzle`).
+2. **Model-specialized** — lists the variants of one printer model (BBL-style `... @<Vendor> <Model>`).
+   It should cover every variant of its model, not only the nozzle it was authored for.
+3. **Family / series** — lists variants spanning a printer family or series.
+4. **Generic / catch-all** — vendor-wide, covering many unrelated models (often the bare
+   `Generic <mat> @<Vendor>`).
+
+Rules:
+
+- A model-specialized profile is extended to **all** variants of its model, and each variant it thereby
+  starts covering is removed from the family and generic profiles that also listed it — including variants
+  that had no overlap before. Apply it per nozzle, not just 0.4.
+- Apply it **per product**: trim only the material that has a specialized profile from the generic; a
+  material whose product has no specialized profile keeps the variant in the generic.
+- Never strip coverage a variant has nowhere else to get. If a variant has no variant-level specialized
+  profile, the next level down keeps it; when the model has specialized profiles, the model-level one wins
+  over the family/generic.
+- Moving coverage is preferred over deleting. If a profile must be deleted, remove the more general
+  one, not the specialized profile that carries the tune.
+- After moving coverage, repoint the affected `default_filament_profile` (machine) and clean the model's
+  `default_materials`: they should name the most specific profile that covers the variant, and should not
+  keep generic entries that no longer cover the model. This rule applies equally when adding or fixing
+  defaults.
+
+Multiple profiles of one product with **disjoint** `compatible_printers` is the intended end state.
+Adding coverage to the specialized profile and removing it from the generic is the preferred direction.
+
+**Detection caveat:** `orca_profile_tool.py check` is blind to this; only the C++ validator behind the full
+`./scripts/check_profile.sh` reports it (`validate_system`). Always confirm with that, not the vendor-scoped
+loop.
+
 ## Alias shadowing
 
 A printer-specific filament in either the library or a vendor bundle supersedes the library fallback

.claude/skills/orca-profiles/references/naming.md

@@ -0,0 +1,60 @@
+# Preset naming
+
+A preset's `name` is the loader's key, not decoration. The index registers it; `inherits`,
+`compatible_printers` and the `default_*` keys reference it by the exact string; `renamed_from` depends
+on it; and `setting_id` / `filament_id` hash it (see [ids.md](ids.md)). Two presets of one type in a
+bundle may not share a name (`check_preset_name_uniqueness`). Treat a name change as an identity change,
+not a relabel.
+
+Naming is convention only where the loader does not parse it. What the loader actually acts on:
+
+| Type | Shape | Acted on |
+| --- | --- | --- |
+| `machine_model` | `<Model>` | the exact string, named by a variant's `printer_model` |
+| `machine` | `<Model> <nozzle> nozzle` | the exact string, named by `compatible_printers`; `printer_variant` must equal a nozzle diameter |
+| `process` | `<lh>mm <Quality> @<target>` | the exact string when referenced or selected; the `@<target>` half is a label |
+| `filament` | `<Product> @<target>` | text before the first `@` is the **alias**, used for shadowing; the rest is a label |
+
+## `machine_model`
+
+`<Model>` — the vendor-prefixed model name (`Bambu Lab X1 Carbon`, `Creality K1`, `Prusa CORE One`). A
+variant names it verbatim in `printer_model`; a mismatch makes the variant invalid. `check_name_consistency`
+forces the index entry to equal the file's `name`, and the variant's `printer_model` targets this string
+([A `machine_model` is not a config preset](machine-profiles.md#a-machine_model-is-not-a-config-preset)).
+It is also the `<Model>_cover.png` and bed-asset stem.
+
+## `machine` (variant)
+
+`<Model> <nozzle> nozzle` is near-universal (`Bambu Lab X1 Carbon 0.4 nozzle`). `printer_variant` holds
+the bare nozzle (`0.4`) and must be an exact member of the model's `nozzle_diameter` list — the hard
+rules are in [The `machine` variant](machine-profiles.md#the-machine-variant). Casing varies
+(`nozzle` / `Nozzle`): match the bundle, not this page. A variant that is not nozzle-specific (a special
+toolhead, a multi-material build) may drop the suffix — still an exact reference. Bases are named
+`fdm_machine_common` / `fdm_<vendor>_common`.
+
+## `process`
+
+`<layer height>mm <quality> @<target>` — [process-profiles.md](process-profiles.md#naming) has the
+quality ladder and the `fdm_process_*` base names. The `@<target>` is a human label, not a reference: it
+usually does not equal a real variant, and compatibility comes from the resolved `compatible_printers`
+list or condition.
+
+## `filament`
+
+`<Product> @<target>`. The product half is what `filament_id` hashes and what survives as the **alias** up
+to the first `@`; the target half is a label except for reserved forms:
+
+- `@base` — a non-instantiated product root. `@base` is convention; a base is really identified by
+  `instantiation: "false"` and no `setting_id` ([the three-part shape](filament-profiles.md#the-three-part-shape)).
+- `@System` — the OrcaFilamentLibrary selectable shim. The literal `Generic <mat> @System` is
+  load-bearing for 3MF/project recovery, beyond the alias rule ([alias shadowing](filament-profiles.md#alias-shadowing)).
+- `@<Vendor>`, `@<Vendor> <Model>`, `@<Vendor> <Model> <nozzle> nozzle` — printer tunes, BBL's shape.
+  Other vendors differ (a bare model, a printer serial, Creality's `@<Model>-all`). Specificity is judged
+  from `compatible_printers`, not the name
+  ([one variant, one profile](filament-profiles.md#overlapping-coverage-one-variant-one-profile-per-product)).
+
+## Not the same as the filename
+
+The loader keys off `name`, and a filename that disagrees usually still loads. Index `name` must equal the
+file's `name`, and the filename should match `sub_path`; a mismatch that differs only in case breaks
+another platform ([cross-platform paths](validation.md#cross-platform-paths)).

.claude/skills/orca-profiles/references/review-checklist.md

@@ -79,8 +79,15 @@ and written in the preset's own file — golden rule 6, with the flattened-vs-ow
 inherited or copied the base's full printer list, and for two presets of one product with overlapping
 lists — duplicate combobox entries and an ambiguous AMS match.
 
+Two presets of one product (`filament_id`) must not share a variant. Resolve it by specificity: move the
+variant to the most specific preset and remove it from the more general ones — preferred over deleting a
+profile. Then repoint the machine's `default_filament_profile` and the model's `default_materials` at the
+profile that now covers it. See
+[one variant, one profile](filament-profiles.md#overlapping-coverage-one-variant-one-profile-per-product).
+
 *Why:* real shipped bugs twice (`b7b3418baf` "showing up everywhere", `ff83aa41ef` duplicate Flashforge
-entries).
+entries). The Python `check` passes on an overlap; only the full `check_profile.sh` (`validate_system`)
+reports `Ambiguous AMS filament match`.
 
 ## 6. Model ↔ variant ↔ process consistency
 
@@ -128,7 +135,11 @@ numbers nobody measured.
 ## 11. `default_materials` (checked by CI)
 
 `check` fails on a `default_materials` / `default_filament_profile` name that resolves to no system
-filament, so a dangling entry no longer reaches review. Scope the run while working on one vendor:
+filament, so a dangling entry no longer reaches review. When compatibility moves between profiles of a
+product, the machine's `default_filament_profile` and the model's `default_materials` must be repointed at
+the most specific profile that still covers the variant, dropping generic entries that no longer apply —
+the same [specificity rule](filament-profiles.md#overlapping-coverage-one-variant-one-profile-per-product)
+applies when adding or fixing defaults. Scope the run while working on one vendor:
 
 ```bash
 python3 scripts/orca_profile_tool.py check --vendor "<Vendor>"   # py -3 on Windows

.claude/skills/orca-profiles/references/validation.md

@@ -20,8 +20,11 @@ default Windows client refuses to run a checked-out `.ps1` at all. The `.ps1` fi
 probing `py -3`, then `python`, then `python3`; run the tool by hand with `py -3` for the same reason.
 
 Every check in the run happens even after an earlier one fails; the script exits non-zero if any did, and writes
-`.test/check_profiles/logs/<check>.log` plus, on failure, `.test/check_profiles/pr_comment.md` — the same
-report CI posts on the PR. A stale `.test/check_profiles/.lock` after a crash must be removed by hand.
+`logs/<check>.log` plus, on failure, `pr_comment.md` under a per-user cache dir — the same report CI posts on the PR.
+That dir is `~/Library/Caches/orca-profile-check` on macOS, `${XDG_CACHE_HOME:-~/.cache}/orca-profile-check` on Linux
+and `%LOCALAPPDATA%\orca-profile-check` on Windows; it is named apart from OrcaSlicer's own per-user dirs and sits
+outside the checkout, so every worktree shares one copy. `--work-dir` / `-WorkDir` overrides it. A stale `.lock`
+there after a crash must be removed by hand.
 
 ## The five checks
 
@@ -150,9 +153,10 @@ Two things it therefore does **not** enforce:
 
 Built from `src/dev-utils/OrcaSlicer_profile_validator.cpp` (`-DORCA_TOOLS=ON`).
 Both scripts find a local build under `build*/` — `check_profile.sh` tries Release, RelWithDebInfo, then
-Debug, and `check_profile.ps1` adds MinSizeRel — else they download the nightly into
-`.test/check_profiles/validator`. Pass `--download` / `-Download` to match CI exactly, since a stale
-local build is used silently. Windows looks for `OrcaSlicer_profile_validator.exe`.
+Debug, and `check_profile.ps1` adds MinSizeRel — else they download the nightly into the
+`validator` subdirectory of the per-user cache dir (see above). Pass `--download` / `-Download` to
+match CI exactly, since a stale local build is used silently. Windows looks for
+`OrcaSlicer_profile_validator.exe`.
 
 If your build lives somewhere else entirely, point at it with `--validator` / `-Validator`, or set
 `ORCA_PROFILE_VALIDATOR` (`$env:ORCA_PROFILE_VALIDATOR` in PowerShell).
@@ -223,7 +227,7 @@ Keep stems tidy too, but a space immediately before `.json` is not a trailing pa
 | `references unknown compatible_printers "<p>"` | the printer was renamed or deleted; fix the reference |
 | `references renamed compatible_printers "<old>" (now "<new>")` | in-tree references must name the current preset; `renamed_from` does not excuse them |
 | `Filament preset "<f>" is missing compatible_printers setting` | non-library filaments need a non-empty list in their **own** file — the flattened-vs-own-key trap is in [filament-profiles.md](filament-profiles.md#compatible_printers) |
-| `Ambiguous AMS filament match: N presets share filament_id "X" … printer "Y"` | make the lists disjoint, or fix an `inherits` pointing at another material's `@base` |
+| `Ambiguous AMS filament match: N presets share filament_id "X" … printer "Y"` | make the lists disjoint by [specificity](filament-profiles.md#overlapping-coverage-one-variant-one-profile-per-product) — the specialized profile keeps the variant, the general ones drop it; prefer this over deleting a profile — or fix an `inherits` pointing at another material's `@base`. `orca_profile_tool.py check` does not catch this; only `validate_system` here does |
 | `Layer height cannot exceed nozzle diameter.` / `Line width too small` | `Print::validate()` flow rules |
 | `[ERROR] … no <V>.json list references it, so it never loads` | `update-index`, or delete the file |
 | `[ERROR] … references it and it declares no profile type` | set the correct `type` explicitly, then `normalize` and `update-index` |

.github/workflows/build_all.yml

@@ -330,12 +330,13 @@ jobs:
     # sources are unchanged, so a re-run of the same commit would skip the
     # OrcaSlicer module and ship no test asset. A per-run value in that module's
     # env keeps it rebuilding; orca_deps stays cached, and the compiler cache
-    # still serves the rebuild.
-    - name: Inject commit hash and flatpak-builder cache buster into Flatpak manifest
+    # still serves the rebuild. run-tests on the same module builds the test
+    # binaries.
+    - name: Inject commit hash, run-tests and cache buster into Flatpak manifest
       env:
         flatpak_builder_cache_buster: ${{ github.run_id }}-${{ github.run_attempt }}
       run: |
-        sed -i "/name: OrcaSlicer/{n;s|buildsystem: simple|buildsystem: simple\n    build-options:\n      env:\n        flatpak_builder_cache_buster: \"$flatpak_builder_cache_buster\"\n        git_commit_hash: \"$git_commit_hash\"|}" \
+        sed -i "/name: OrcaSlicer/{n;s|buildsystem: simple|buildsystem: simple\n    run-tests: true\n    build-options:\n      env:\n        flatpak_builder_cache_buster: \"$flatpak_builder_cache_buster\"\n        git_commit_hash: \"$git_commit_hash\"|}" \
           scripts/flatpak/com.orcaslicer.OrcaSlicer.yml
       shell: bash
     # flatpak-builder's --ccache only wraps cc and gcc, and the manifest builds
@@ -381,9 +382,6 @@ jobs:
         save-cache: false
         arch: ${{ matrix.variant.arch }}
         upload-artifact: false
-        # run-tests fires the module's build-only test-commands; keep-build-dirs
-        # retains the binaries for the packaging step below.
-        run-tests: true
         keep-build-dirs: true
     # The build has just touched everything it can use, so an object untouched
     # for a week is dead, usually orphaned by a flag change.
@@ -449,10 +447,13 @@ jobs:
         # the bounds checks are compiled in, so a stripped exe still catches them.
         find "$d/build_flatpak/tests" -type f -perm -u+x -exec strip --strip-unneeded {} + 2>/dev/null || true
         # At runtime the tests read tests/ (TEST_DATA_DIR), scripts/, and under
-        # resources/ the shipped profiles (PROFILES_DIR) and the printers/ maps.
+        # resources/ the shipped profiles (PROFILES_DIR), the printers/ maps, and
+        # the icon SVGs (NativeCommands icon names are checked against them).
         find "$d" -mindepth 1 -maxdepth 1 -type d \
           ! -name tests ! -name build_flatpak ! -name scripts ! -name resources -exec rm -rf {} +
-        find "$d/resources" -mindepth 1 -maxdepth 1 ! -name profiles ! -name printers -exec rm -rf {} +
+        find "$d/resources" -mindepth 1 -maxdepth 1 ! -name profiles ! -name printers ! -name images -exec rm -rf {} +
+        # Only the SVGs are read; the png/ico/icns/gif assets are ~35MB of dead weight.
+        find "$d/resources/images" -mindepth 1 -maxdepth 1 ! -name '*.svg' -exec rm -rf {} + 2>/dev/null || true
         tar -cf flatpak-test-asset.tar flatpak_app "$d"
     - name: Upload flatpak test asset
       uses: actions/upload-artifact@v7

.github/workflows/build_orca.yml

@@ -448,9 +448,26 @@ jobs:
 
       - name: Install nsis
         if: runner.os == 'Windows' && !vars.SELF_HOSTED
+        shell: pwsh
+        # The Chocolatey community feed intermittently 504s, and `choco install`
+        # exits 0 when package resolution fails that way. Unchecked, the job then
+        # builds for ~25 minutes before `cpack -G NSIS` reports a missing makensis.
+        # Retry the install and verify makensis itself, so a real failure stops here.
         run: |
           dir "C:/Program Files (x86)/Windows Kits/10/Include"
-          choco install nsis
+          $nsisDir = Join-Path ${env:ProgramFiles(x86)} 'NSIS'
+          $makensis = Join-Path $nsisDir 'makensis.exe'
+          for ($attempt = 1; $attempt -le 3 -and -not (Test-Path $makensis); $attempt++) {
+            if ($attempt -gt 1) { Start-Sleep -Seconds (15 * $attempt) }
+            Write-Host "::group::choco install nsis (attempt $attempt)"
+            choco install nsis --yes --no-progress
+            Write-Host "::endgroup::"
+          }
+          if (-not (Test-Path $makensis)) {
+            throw "NSIS install failed: $makensis not found after 3 attempts."
+          }
+          & $makensis /VERSION
+          $nsisDir | Out-File -Append -FilePath $env:GITHUB_PATH -Encoding utf8
 
       - name: Build slicer Win
         if: runner.os == 'Windows'

.github/workflows/pr-merge-bot.yml

@@ -529,7 +529,7 @@ jobs:
       && github.event_name == 'pull_request_target'
     permissions:
       contents: read
-      pull-requests: read
+      pull-requests: write
       issues: write
     runs-on: ubuntu-latest
     timeout-minutes: 5
@@ -636,7 +636,7 @@ jobs:
       && github.event_name == 'pull_request_target'
     permissions:
       contents: read        # delegatable subtree, for file modes
-      pull-requests: read
+      pull-requests: write
       issues: write         # label + comment
     runs-on: ubuntu-latest
     timeout-minutes: 10

.gitignore

@@ -52,5 +52,4 @@ internal_docs/
 __pycache__/
 *.pyc
 *.opc
-/.test/
 docs/superpowers/

localization/i18n/list.txt

@@ -125,6 +125,7 @@ src/slic3r/GUI/ThermalPreconditioningDialog.hpp
 src/slic3r/GUI/Jobs/SLAImportJob.cpp
 src/slic3r/GUI/Jobs/UpgradeNetworkJob.cpp
 src/slic3r/GUI/AboutDialog.cpp
+src/slic3r/GUI/ActionRegistry.cpp
 src/slic3r/GUI/AMSMaterialsSetting.cpp
 src/slic3r/GUI/ExtrusionCalibration.cpp
 src/slic3r/GUI/AmsMappingPopup.cpp
@@ -159,6 +160,7 @@ src/slic3r/GUI/SelectMachinePop.cpp
 src/slic3r/GUI/StatusPanel.cpp
 src/slic3r/GUI/Monitor.cpp
 src/slic3r/GUI/MsgDialog.cpp
+src/slic3r/GUI/NativeCommands.cpp
 src/slic3r/GUI/NotificationManager.hpp
 src/slic3r/GUI/NotificationManager.cpp
 src/slic3r/GUI/ObjectDataViewModel.cpp
@@ -179,6 +181,8 @@ src/slic3r/GUI/PublishDialog.cpp
 src/slic3r/GUI/PublishSettingsDialog.cpp
 src/slic3r/GUI/SavePresetDialog.cpp
 src/slic3r/GUI/Search.cpp
+src/slic3r/GUI/SettingsIndex.cpp
+src/slic3r/GUI/SpeedDialDialog.cpp
 src/slic3r/GUI/Selection.cpp
 src/slic3r/GUI/SelectMachine.cpp
 src/slic3r/GUI/PrePrintChecker.cpp
@@ -246,6 +250,7 @@ src/slic3r/GUI/TroubleshootDialog.cpp
 src/slic3r/Utils/3DPrinterOS.cpp
 src/slic3r/Utils/AstroBox.cpp
 src/slic3r/Utils/Duet.cpp
+src/slic3r/Utils/UltiMaker.cpp
 src/slic3r/Utils/FlashAir.cpp
 src/slic3r/Utils/MKS.cpp
 src/slic3r/Utils/Moonraker.cpp

resources/images/action_default.svg

@@ -0,0 +1,2 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<svg xmlns="http://www.w3.org/2000/svg" width="16" height="16" viewBox="0 0 16 16"><path d="M14.5,1.5v12a1,1,0,0,1-1,1H1.5a1,1,0,0,1-1-1V1.5a1,1,0,0,1,1-1h12a1,1,0,0,1,1,1Z" style="fill:none;stroke:#949494;stroke-linecap:round;stroke-linejoin:round"/><polyline points="4,5 6.5,7.5 4,10" style="fill:none;stroke:#009688;stroke-linecap:round;stroke-linejoin:round"/><line x1="8" y1="10" x2="11" y2="10" style="fill:none;stroke:#009688;stroke-linecap:round;stroke-linejoin:round"/></svg>

resources/images/edit_12px.svg

@@ -0,0 +1 @@
+<?xml version="1.0" encoding="UTF-8"?><svg id="a" xmlns="http://www.w3.org/2000/svg" viewBox="0 0 12 12"><path d="M11.5,5.5v5c0,.55-.45,1-1,1H1.5c-.55,0-1-.45-1-1V1.5C.5.95.95.5,1.5.5h5M3.5,6.5v2h2l5.59-5.59c.55-.55.55-1.45,0-2s-1.45-.55-2,0L3.5,6.5Z" style="fill:none; stroke:#949494; stroke-linecap:square; stroke-linejoin:round;"/></svg>

resources/profiles/Creality/filament/CR-ABS @Ender-2 Pro-all.json

@@ -0,0 +1,155 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-2 Pro-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "xXPIfJOKtSIkbgSZ",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_max_speed": [
+		"20"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"overhang_fan_speed": [
+		"100"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"20"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "80",
+	"customized_plate_temp_initial_layer": "80",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-2 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 S1 Plus-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 S1 Plus-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "41fKjFexWC3Zh7XZ",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"filament_start_gcode": [
+		"; Filament gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Plus 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 S1 Pro-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 S1 Pro-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "SDigCIbuTDRn8b96",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"filament_start_gcode": [
+		"; Filament gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 S1 Sonic-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 S1 Sonic-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "jYdpNiDMaOz2Ay6R",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Sonic 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 S1-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 S1-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "5kp6VbwvXPo7Lvzg",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"filament_start_gcode": [
+		"; Filament gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 V3 KE-all.json

@@ -0,0 +1,151 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 V3 KE-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "XUzmyFDwpqu4Kfjh",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_min_speed": [
+		"70"
+	],
+	"filament_cost": [
+		"15"
+	],
+	"filament_density": [
+		"1.08"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"20"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"0.4"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature_range_high": [
+		"260"
+	],
+	"nozzle_temperature_range_low": [
+		"230"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		"; Filament gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_cds_fan_start_at_height": "0",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.05",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 KE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 V3 Plus-all.json

@@ -0,0 +1,146 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 V3 Plus-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "2bvhLTGnyzWCVkPy",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_min_speed": [
+		"70"
+	],
+	"filament_cost": [
+		"15"
+	],
+	"filament_density": [
+		"1.08"
+	],
+	"filament_deretraction_speed": [
+		"0"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.926"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"20"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"100%"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"30"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"0"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.4"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature_range_high": [
+		"260"
+	],
+	"nozzle_temperature_range_low": [
+		"230"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 Plus 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3 V3-all.json

@@ -0,0 +1,172 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3 V3-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "MQURrCD6wSxqa1jP",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"cool_plate_temp_initial_layer": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_max_speed": [
+		"30"
+	],
+	"fan_min_speed": [
+		"20"
+	],
+	"filament_cost": [
+		"15"
+	],
+	"filament_density": [
+		"1.08"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.97"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"14"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"2"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature_range_high": [
+		"260"
+	],
+	"nozzle_temperature_range_low": [
+		"230"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "100",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "1",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "100",
+	"epoxy_resin_plate_temp_initial_layer": "100",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,230],[10.0,240],[20.0,250]]",
+	"pressure_advance": "0.046",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 0.4 nozzle",
+		"Creality Ender-3 V3 0.6 nozzle",
+		"Creality Ender-3 V3 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-3-all.json

@@ -0,0 +1,138 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-3-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "H4UaUhKIsHDvC918",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"6"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"filament_start_gcode": [
+		"; Filament gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-5 S1 Sonic-all.json

@@ -0,0 +1,135 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-5 S1 Sonic-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "p6IjY3IqwpTbVeUP",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"70"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_deretraction_speed": [
+		"40"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"1"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"40"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"1"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-5 S1 Sonic 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Ender-5 S1-all.json

@@ -0,0 +1,135 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Ender-5 S1-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "JJLc8iPdvZucHYiJ",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"70"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"35"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_deretraction_speed": [
+		"40"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"1"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"40"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"1"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-5 S1 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Sermoon D3 Pro-all.json

@@ -0,0 +1,166 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Sermoon D3 Pro-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "iYMDiv64la5GboAA",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"cool_plate_temp_initial_layer": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"filament_cost": [
+		"15"
+	],
+	"filament_density": [
+		"1.08"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature_range_high": [
+		"280"
+	],
+	"overhang_fan_speed": [
+		"50"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "1",
+	"chamber_temperature": "60",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "80",
+	"customized_plate_temp_initial_layer": "80",
+	"default_filament_colour": "\"\"",
+	"dont_slow_down_outer_wall": "0",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_long_retractions_when_cut": "nil",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_ramming_parameters": "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_retraction_distances_when_cut": "nil",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_stamping_distance": "0",
+	"filament_stamping_loading_speed": "0",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"idle_temperature": "0",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],[10.0,220],[12.0,230]]",
+	"pellet_flow_coefficient": "0.4157",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon D3 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-ABS @Sermoon M300-all.json

@@ -0,0 +1,160 @@
+{
+	"type": "filament",
+	"name": "CR-ABS @Sermoon M300-all",
+	"inherits": "fdm_filament_abs",
+	"from": "system",
+	"setting_id": "afINvBBB1U1PjGVB",
+	"filament_id": "OFGwZmgS",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"cool_plate_temp_initial_layer": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_max_speed": [
+		"60"
+	],
+	"filament_cost": [
+		"15"
+	],
+	"filament_density": [
+		"1.08"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"18"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"90%"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"Slope Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"100"
+	],
+	"hot_plate_temp_initial_layer": [
+		"100"
+	],
+	"nozzle_temperature_range_high": [
+		"280"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"14"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"textured_plate_temp": [
+		"100"
+	],
+	"textured_plate_temp_initial_layer": [
+		"100"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n{if (layer_z > first_layer_height) }\nM104 S[nozzle_temperature]\n{else} \nM104 S[first_layer_temperature]\n{endif}"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "100",
+	"customized_plate_temp_initial_layer": "100",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon M300 0.4 nozzle",
+		"Creality Sermoon M300 0.6 nozzle",
+		"Creality Sermoon M300 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-Nylon @Ender-3 V3 Plus-all.json

@@ -0,0 +1,188 @@
+{
+	"type": "filament",
+	"name": "CR-Nylon @Ender-3 V3 Plus-all",
+	"inherits": "fdm_filament_pa",
+	"from": "system",
+	"setting_id": "JOqqaEHv9emSaO58",
+	"filament_id": "OFvLppPU",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"close_fan_the_first_x_layers": [
+		"1"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"50"
+	],
+	"cool_plate_temp_initial_layer": [
+		"50"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"50"
+	],
+	"eng_plate_temp_initial_layer": [
+		"50"
+	],
+	"fan_cooling_layer_time": [
+		"100"
+	],
+	"fan_max_speed": [
+		"100"
+	],
+	"fan_min_speed": [
+		"30"
+	],
+	"filament_cost": [
+		"52"
+	],
+	"filament_density": [
+		"1.12"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"50"
+	],
+	"hot_plate_temp_initial_layer": [
+		"50"
+	],
+	"nozzle_temperature": [
+		"260"
+	],
+	"nozzle_temperature_initial_layer": [
+		"260"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"250"
+	],
+	"overhang_fan_speed": [
+		"100"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_for_layer_cooling": [
+		"1"
+	],
+	"slow_down_layer_time": [
+		"4"
+	],
+	"slow_down_min_speed": [
+		"10"
+	],
+	"temperature_vitrification": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"50"
+	],
+	"textured_plate_temp_initial_layer": [
+		"50"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 Plus 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @CR-10 SE-all.json

@@ -0,0 +1,167 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @CR-10 SE-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "ca0t7XsRrFpxcL7a",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"90"
+	],
+	"fan_min_speed": [
+		"80"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_deretraction_speed": [
+		"0"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"9"
+	],
+	"filament_retract_before_wipe": [
+		"100%"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"30"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"0"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.4"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-10 SE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @CR-10 Smart Pro-all.json

@@ -0,0 +1,133 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @CR-10 Smart Pro-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "iB29j2vvnyfpO4tk",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"80"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.3"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"12"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"220"
+	],
+	"nozzle_temperature_initial_layer": [
+		"220"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-10 Smart Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @CR-10-all.json

@@ -0,0 +1,133 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @CR-10-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "LHxnOzAAJr1mk5GK",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"80"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.3"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"12"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"220"
+	],
+	"nozzle_temperature_initial_layer": [
+		"220"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-10 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @CR-M4 SE-all.json

@@ -0,0 +1,170 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @CR-M4 SE-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "N9vgkspyIr8EV1T8",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"close_fan_the_first_x_layers": [
+		"1"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"45"
+	],
+	"fan_cooling_layer_time": [
+		"100"
+	],
+	"fan_min_speed": [
+		"50"
+	],
+	"filament_cost": [
+		"22"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_deretraction_speed": [
+		"50"
+	],
+	"filament_flow_ratio": [
+		"0.9"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"12"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"0.05"
+	],
+	"filament_retraction_speed": [
+		"50"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"0"
+	],
+	"filament_wipe_distance": [
+		"2"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"nozzle_temperature_range_high": [
+		"260"
+	],
+	"nozzle_temperature_range_low": [
+		"240"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		"\" \""
+	],
+	"filament_end_gcode": [
+		"\" \""
+	],
+	"activate_chamber_temp_control": "1",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "1",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "70",
+	"epoxy_resin_plate_temp_initial_layer": "70",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,230],[5.0,240],[8.0,250]]",
+	"pressure_advance": "0.08",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-M4 SE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-2 Pro-all.json

@@ -0,0 +1,135 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-2 Pro-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "F7h6B3GqsyWLIXWk",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"100"
+	],
+	"fan_min_speed": [
+		"100"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"220"
+	],
+	"nozzle_temperature_initial_layer": [
+		"220"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-2 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 S1 Plus-all.json

@@ -0,0 +1,144 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 S1 Plus-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "ukQaApwo1Kafy1of",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"40"
+	],
+	"fan_min_speed": [
+		"10"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Plus 0.4 nozzle"
+	],
+	"filament_vendor": [
+		"Creality"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 S1 Pro-all.json

@@ -0,0 +1,144 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 S1 Pro-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "YzCFzg5CFVXkP5mI",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"40"
+	],
+	"fan_min_speed": [
+		"10"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Pro 0.4 nozzle"
+	],
+	"filament_vendor": [
+		"Creality"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 S1 Sonic-all.json

@@ -0,0 +1,147 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 S1 Sonic-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "nhmw2HhDlNRvvccd",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"40"
+	],
+	"fan_min_speed": [
+		"10"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Sonic 0.4 nozzle"
+	],
+	"filament_vendor": [
+		"Creality"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 S1-all.json

@@ -0,0 +1,144 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 S1-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "HOXafIaVQNYa5uzz",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"40"
+	],
+	"fan_min_speed": [
+		"10"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 0.4 nozzle"
+	],
+	"filament_vendor": [
+		"Creality"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 V2-all.json

@@ -0,0 +1,131 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 V2-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "KOU7rizOewXtUGdS",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"80"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"100"
+	],
+	"fan_min_speed": [
+		"100"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"220"
+	],
+	"nozzle_temperature_initial_layer": [
+		"220"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.4",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V2 0.4 nozzle"
+	],
+	"filament_vendor": [
+		"Creality"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 V3 KE-all.json

@@ -0,0 +1,142 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 V3 KE-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "RtNydGhtx6FMjQDr",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"40"
+	],
+	"fan_min_speed": [
+		"30"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.23"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"9"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_cds_fan_start_at_height": "0",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "1",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "70",
+	"epoxy_resin_plate_temp_initial_layer": "70",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.08",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 KE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 V3 Plus-all.json

@@ -0,0 +1,169 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 V3 Plus-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "Z3uXiHTYNnlPwfXX",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"90"
+	],
+	"fan_min_speed": [
+		"80"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.23"
+	],
+	"filament_deretraction_speed": [
+		"0"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"9"
+	],
+	"filament_retract_before_wipe": [
+		"100%"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"30"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"0"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.4"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "70",
+	"epoxy_resin_plate_temp_initial_layer": "70",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 Plus 0.4 nozzle",
+		"Creality Ender-3 V3 Plus 0.6 nozzle",
+		"Creality Ender-3 V3 Plus 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3 V3-all.json

@@ -0,0 +1,156 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3 V3-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "jLTxg3JhZaoBjPDd",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"90"
+	],
+	"fan_min_speed": [
+		"80"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.23"
+	],
+	"filament_deretraction_speed": [
+		"25"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_speed": [
+		"30"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"235"
+	],
+	"nozzle_temperature_initial_layer": [
+		"235"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "100",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "50",
+	"epoxy_resin_plate_temp_initial_layer": "50",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 0.4 nozzle",
+		"Creality Ender-3 V3 0.6 nozzle",
+		"Creality Ender-3 V3 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-3-all.json

@@ -0,0 +1,138 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-3-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "XtRCnvDgIt3woTfm",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"fan_min_speed": [
+		"30"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"2"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"8"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-5 S1 Sonic-all.json

@@ -0,0 +1,165 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-5 S1 Sonic-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "kEN1rd7J0bDhpXLB",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"70"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_deretraction_speed": [
+		"30"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_when_changing_layer": [
+		"1"
+	],
+	"filament_retraction_length": [
+		"1.5"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"40"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"1"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-5 S1 Sonic 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Ender-5 S1-all.json

@@ -0,0 +1,162 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Ender-5 S1-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "SXeN7LY4p9TpzIfK",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"70"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"30"
+	],
+	"filament_density": [
+		"1.27"
+	],
+	"filament_deretraction_speed": [
+		"30"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_when_changing_layer": [
+		"1"
+	],
+	"filament_retraction_length": [
+		"1.5"
+	],
+	"filament_retraction_minimum_travel": [
+		"2"
+	],
+	"filament_retraction_speed": [
+		"40"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"1"
+	],
+	"filament_wipe_distance": [
+		"1"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-5 S1 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Sermoon D3 Pro-all.json

@@ -0,0 +1,151 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Sermoon D3 Pro-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "PhFJ45TOClwggKYD",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"close_fan_the_first_x_layers": [
+		"1"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"100"
+	],
+	"cool_plate_temp_initial_layer": [
+		"100"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"105"
+	],
+	"eng_plate_temp_initial_layer": [
+		"105"
+	],
+	"fan_cooling_layer_time": [
+		"100"
+	],
+	"fan_max_speed": [
+		"80"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"14"
+	],
+	"filament_density": [
+		"1.23"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"7"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"260"
+	],
+	"nozzle_temperature_range_low": [
+		"230"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"110"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "80",
+	"customized_plate_temp_initial_layer": "80",
+	"default_filament_colour": "\"\"",
+	"dont_slow_down_outer_wall": "0",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_long_retractions_when_cut": "nil",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_ramming_parameters": "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_retraction_distances_when_cut": "nil",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_stamping_distance": "0",
+	"filament_stamping_loading_speed": "0",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"idle_temperature": "0",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],[10.0,220],[12.0,230]]",
+	"pellet_flow_coefficient": "0.4157",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon D3 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Sermoon D3-all.json

@@ -0,0 +1,132 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Sermoon D3-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "Pw1DtBsgpbzj8P0k",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"35"
+	],
+	"cool_plate_temp_initial_layer": [
+		"35"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"fan_min_speed": [
+		"20"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"nozzle_temperature_range_low": [
+		"190"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.05",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon D3 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Sermoon M300-all.json

@@ -0,0 +1,156 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Sermoon M300-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "WaYzXCaD9MuLDXsX",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"70"
+	],
+	"cool_plate_temp_initial_layer": [
+		"70"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"50"
+	],
+	"eng_plate_temp_initial_layer": [
+		"55"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"80"
+	],
+	"fan_min_speed": [
+		"40"
+	],
+	"filament_cost": [
+		"20"
+	],
+	"filament_density": [
+		"1.24"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"18"
+	],
+	"filament_retract_before_wipe": [
+		"90%"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_z_hop_types": [
+		"Slope Lift"
+	],
+	"hot_plate_temp": [
+		"70"
+	],
+	"hot_plate_temp_initial_layer": [
+		"70"
+	],
+	"nozzle_temperature": [
+		"250"
+	],
+	"nozzle_temperature_initial_layer": [
+		"250"
+	],
+	"nozzle_temperature_range_high": [
+		"270"
+	],
+	"nozzle_temperature_range_low": [
+		"220"
+	],
+	"overhang_fan_speed": [
+		"90"
+	],
+	"overhang_fan_threshold": [
+		"10%"
+	],
+	"reduce_fan_stop_start_freq": [
+		"1"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"12"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"70"
+	],
+	"textured_plate_temp_initial_layer": [
+		"70"
+	],
+	"filament_start_gcode": [
+		"; filament start gcode\n{if (layer_z > first_layer_height) }\nM104 S[nozzle_temperature]\n{else} \nM104 S[first_layer_temperature]\n{endif}"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[0.5,240],[1.0,240],[1.2,250]]",
+	"pressure_advance": "0.07",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon M300 0.4 nozzle",
+		"Creality Sermoon M300 0.6 nozzle",
+		"Creality Sermoon M300 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PETG @Sermoon V1 Pro-all.json

@@ -0,0 +1,129 @@
+{
+	"type": "filament",
+	"name": "CR-PETG @Sermoon V1 Pro-all",
+	"inherits": "fdm_filament_petg",
+	"from": "system",
+	"setting_id": "yPw0Q8cZoH0z5Q5W",
+	"filament_id": "OF3WQaKK",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"35"
+	],
+	"cool_plate_temp_initial_layer": [
+		"35"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"0"
+	],
+	"eng_plate_temp_initial_layer": [
+		"0"
+	],
+	"fan_cooling_layer_time": [
+		"30"
+	],
+	"fan_max_speed": [
+		"50"
+	],
+	"fan_min_speed": [
+		"20"
+	],
+	"filament_flow_ratio": [
+		"0.98"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_type": [
+		"PETG"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"hot_plate_temp": [
+		"80"
+	],
+	"hot_plate_temp_initial_layer": [
+		"80"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"nozzle_temperature_range_low": [
+		"190"
+	],
+	"overhang_fan_threshold": [
+		"50%"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "70",
+	"customized_plate_temp_initial_layer": "70",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.05",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Sermoon V1 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @CR-10-all.json

@@ -0,0 +1,151 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @CR-10-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "gRYsvflqQ8IIyNOu",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"35"
+	],
+	"cool_plate_temp_initial_layer": [
+		"35"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"45"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"1"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"200"
+	],
+	"nozzle_temperature_initial_layer": [
+		"200"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		";filament start gcode"
+	],
+	"filament_end_gcode": [
+		";filament end gcode "
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"customized_plate_temp": "60",
+	"customized_plate_temp_initial_layer": "60",
+	"default_filament_colour": "\"\"",
+	"dont_slow_down_outer_wall": "0",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_long_retractions_when_cut": "nil",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_ramming_parameters": "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_retraction_distances_when_cut": "nil",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_stamping_distance": "0",
+	"filament_stamping_loading_speed": "0",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"idle_temperature": "0",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],[10.0,220],[12.0,230]]",
+	"pellet_flow_coefficient": "0.4157",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-10 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @CR-M4 SE-all.json

@@ -0,0 +1,146 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @CR-M4 SE-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "tABggke8tUaNmEEh",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"45"
+	],
+	"fan_min_speed": [
+		"50"
+	],
+	"filament_cost": [
+		"22"
+	],
+	"filament_deretraction_speed": [
+		"50"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.9"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"20"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"70"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"0"
+	],
+	"filament_retraction_length": [
+		"0.8"
+	],
+	"filament_retraction_minimum_travel": [
+		"0.05"
+	],
+	"filament_retraction_speed": [
+		"50"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"0"
+	],
+	"filament_wipe_distance": [
+		"2"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Normal Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"overhang_fan_threshold": [
+		"95%"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"10"
+	],
+	"temperature_vitrification": [
+		"100"
+	],
+	"filament_start_gcode": [
+		"\" \""
+	],
+	"filament_end_gcode": [
+		"\" \""
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "1",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "60",
+	"epoxy_resin_plate_temp_initial_layer": "60",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_shrinkage_compensation_z": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,200],[5.0,210],[8.0,220]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality CR-M4 SE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-2 Pro-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-2 Pro-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "pyic9IqsyOiafceu",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"1"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"210"
+	],
+	"nozzle_temperature_initial_layer": [
+		"210"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode\n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-2 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 S1 Plus-all.json

@@ -0,0 +1,123 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 S1 Plus-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "DyGKfjo621EQ9y3H",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"190"
+	],
+	"nozzle_temperature_initial_layer": [
+		"190"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Plus 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 S1 Pro-all.json

@@ -0,0 +1,123 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 S1 Pro-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "CgGlQJsaZQNxVOTe",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"190"
+	],
+	"nozzle_temperature_initial_layer": [
+		"190"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Pro 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 S1 Sonic-all.json

@@ -0,0 +1,126 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 S1 Sonic-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "WsUax8HKz582lvgP",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"190"
+	],
+	"nozzle_temperature_initial_layer": [
+		"190"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 Sonic 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 S1-all.json

@@ -0,0 +1,123 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 S1-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "q2a9vySJTktLFns3",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"8"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1.2"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"190"
+	],
+	"nozzle_temperature_initial_layer": [
+		"190"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 S1 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 V2-all.json

@@ -0,0 +1,128 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 V2-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "0w38xo4i4Hsv1NGO",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"80"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"1"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"10"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "100",
+	"customized_plate_temp": "60",
+	"customized_plate_temp_initial_layer": "60",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "nil",
+	"filament_retract_lift_below": "nil",
+	"filament_retract_lift_enforce": "nil",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V2 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 V3 KE-all.json

@@ -0,0 +1,151 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 V3 KE-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "SpUnsDch11ry1O8N",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"50"
+	],
+	"cool_plate_temp_initial_layer": [
+		"50"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"50"
+	],
+	"eng_plate_temp_initial_layer": [
+		"50"
+	],
+	"filament_cost": [
+		"18"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"18"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"50"
+	],
+	"hot_plate_temp_initial_layer": [
+		"50"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"5"
+	],
+	"textured_plate_temp": [
+		"50"
+	],
+	"textured_plate_temp_initial_layer": [
+		"50"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_cds_fan_start_at_height": "0",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "1",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "50",
+	"epoxy_resin_plate_temp_initial_layer": "50",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.048",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 KE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 V3 Plus-all.json

@@ -0,0 +1,153 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 V3 Plus-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "EgSHGiAjpbFer6VA",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"80"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"65"
+	],
+	"cool_plate_temp_initial_layer": [
+		"65"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"65"
+	],
+	"eng_plate_temp_initial_layer": [
+		"65"
+	],
+	"filament_cost": [
+		"18"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"18"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"65"
+	],
+	"hot_plate_temp_initial_layer": [
+		"65"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"textured_plate_temp": [
+		"65"
+	],
+	"textured_plate_temp_initial_layer": [
+		"65"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_cds_fan_start_at_height": "0.5",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "50",
+	"epoxy_resin_plate_temp_initial_layer": "50",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 Plus 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 V3 SE-all.json

@@ -0,0 +1,166 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 V3 SE-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "HE08t6PGCuot7MAy",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"50"
+	],
+	"cool_plate_temp_initial_layer": [
+		"50"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"45"
+	],
+	"filament_cost": [
+		"25"
+	],
+	"filament_density": [
+		"1.25"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"1"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"40"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"0.2"
+	],
+	"filament_z_hop_types": [
+		"Slope Lift"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"50"
+	],
+	"hot_plate_temp_initial_layer": [
+		"50"
+	],
+	"nozzle_temperature": [
+		"190"
+	],
+	"nozzle_temperature_initial_layer": [
+		"190"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"6"
+	],
+	"slow_down_min_speed": [
+		"20"
+	],
+	"temperature_vitrification": [
+		"100"
+	],
+	"textured_plate_temp": [
+		"50"
+	],
+	"textured_plate_temp_initial_layer": [
+		"50"
+	],
+	"filament_start_gcode": [
+		";filament start gcode"
+	],
+	"filament_end_gcode": [
+		";filament end gcode "
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"enable_special_area_additional_cooling_fan": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[2.0,185],[4.0,190],[7.0,200]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 SE 0.4 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3 V3-all.json

@@ -0,0 +1,163 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3 V3-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "NZMJjZm0Io0FYdX4",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"additional_cooling_fan_speed": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"cool_plate_temp": [
+		"65"
+	],
+	"cool_plate_temp_initial_layer": [
+		"65"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"65"
+	],
+	"eng_plate_temp_initial_layer": [
+		"65"
+	],
+	"filament_cost": [
+		"18"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"0.95"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_max_volumetric_speed": [
+		"18"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"nil"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"hot_plate_temp": [
+		"65"
+	],
+	"hot_plate_temp_initial_layer": [
+		"65"
+	],
+	"nozzle_temperature": [
+		"230"
+	],
+	"nozzle_temperature_initial_layer": [
+		"230"
+	],
+	"nozzle_temperature_range_high": [
+		"240"
+	],
+	"overhang_fan_threshold": [
+		"0%"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"textured_plate_temp": [
+		"65"
+	],
+	"textured_plate_temp_initial_layer": [
+		"65"
+	],
+	"filament_start_gcode": [
+		";filament start gcode\n"
+	],
+	"filament_end_gcode": [
+		";filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "35",
+	"cool_special_cds_fan_speed": "100",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "50",
+	"epoxy_resin_plate_temp_initial_layer": "50",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.0,210],  [10.0,220],  [12.0,230]]",
+	"pressure_advance": "0.02",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 V3 0.4 nozzle",
+		"Creality Ender-3 V3 0.6 nozzle",
+		"Creality Ender-3 V3 0.8 nozzle"
+	]
+}

resources/profiles/Creality/filament/CR-PLA @Ender-3-all.json

@@ -0,0 +1,123 @@
+{
+	"type": "filament",
+	"name": "CR-PLA @Ender-3-all",
+	"inherits": "fdm_filament_pla",
+	"from": "system",
+	"setting_id": "ZzKcZo3q8UkZOVdx",
+	"filament_id": "OFp4ETDP",
+	"instantiation": "true",
+	"activate_air_filtration": [
+		"0"
+	],
+	"complete_print_exhaust_fan_speed": [
+		"80"
+	],
+	"during_print_exhaust_fan_speed": [
+		"60"
+	],
+	"filament_deretraction_speed": [
+		"nil"
+	],
+	"filament_diameter": [
+		"1.75"
+	],
+	"filament_flow_ratio": [
+		"1"
+	],
+	"filament_is_support": [
+		"0"
+	],
+	"filament_minimal_purge_on_wipe_tower": [
+		"15"
+	],
+	"filament_retract_before_wipe": [
+		"nil"
+	],
+	"filament_retract_restart_extra": [
+		"0"
+	],
+	"filament_retract_when_changing_layer": [
+		"nil"
+	],
+	"filament_retraction_length": [
+		"nil"
+	],
+	"filament_retraction_minimum_travel": [
+		"nil"
+	],
+	"filament_retraction_speed": [
+		"nil"
+	],
+	"filament_soluble": [
+		"0"
+	],
+	"filament_vendor": [
+		"Creality"
+	],
+	"filament_wipe": [
+		"nil"
+	],
+	"filament_wipe_distance": [
+		"nil"
+	],
+	"filament_z_hop": [
+		"nil"
+	],
+	"filament_z_hop_types": [
+		"nil"
+	],
+	"full_fan_speed_layer": [
+		"0"
+	],
+	"nozzle_temperature": [
+		"200"
+	],
+	"nozzle_temperature_initial_layer": [
+		"200"
+	],
+	"overhang_fan_threshold": [
+		"25%"
+	],
+	"required_nozzle_HRC": [
+		"0"
+	],
+	"slow_down_layer_time": [
+		"8"
+	],
+	"filament_end_gcode": [
+		"; filament end gcode \n"
+	],
+	"activate_chamber_temp_control": "0",
+	"chamber_temperature": "0",
+	"cool_cds_fan_start_at_height": "0.5",
+	"cool_special_cds_fan_speed": "0",
+	"default_filament_colour": "\"\"",
+	"enable_overhang_bridge_fan": "1",
+	"enable_pressure_advance": "0",
+	"epoxy_resin_plate_temp": "0",
+	"epoxy_resin_plate_temp_initial_layer": "0",
+	"filament_cooling_final_speed": "3.4",
+	"filament_cooling_initial_speed": "2.2",
+	"filament_cooling_moves": "4",
+	"filament_loading_speed": "28",
+	"filament_loading_speed_start": "3",
+	"filament_multitool_ramming": "0",
+	"filament_multitool_ramming_flow": "10",
+	"filament_multitool_ramming_volume": "10",
+	"filament_notes": "\"\"",
+	"filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
+	"filament_retract_lift_above": "0",
+	"filament_retract_lift_below": "0",
+	"filament_retract_lift_enforce": "All Surfaces",
+	"filament_shrink": "100%",
+	"filament_toolchange_delay": "0",
+	"filament_unloading_speed": "90",
+	"filament_unloading_speed_start": "100",
+	"material_flow_dependent_temperature": "0",
+	"material_flow_temp_graph": "[[3.5,200],[7.0,240]]",
+	"pressure_advance": "0.04",
+	"support_material_interface_fan_speed": "-1",
+	"compatible_printers": [
+		"Creality Ender-3 0.4 nozzle"
+	]
+}