Four files overlapped, and each resolution favours upstream where the two sides
had done the same work:
WipeTower's M104/M109 tool qualifier. Both sides bounds-checked the physical
extruder map lookup; upstream omits the T qualifier when the map cannot answer,
where this branch fell back to the logical index and so named a carriage that may
not be the one printing. Upstream's behaviour is what this branch documents
elsewhere, so its version is taken and the local helper is dropped.
get_extruders' mixed-slot switch. Upstream added the same concept to the CLI
overload as expand_mixed_slots, so the GUI overloads' parameter is renamed to
match rather than carrying two names for one idea.
GLCanvas3D's sequential-clearance branch gains upstream's
update_compacted_wipe_tower_clearance for the by-layer case.
The printer_agent re-sync in TabPrinter::reload_config was upstream's and their
preset-undo fix removed it, so it goes; the IMEX modes grid re-sync beside it
stays, since it spans three options and is not a Field.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
nozzle_temperature is variant-expanded, so its length is columns rather than
filament slots. On the dynamic-nozzle path that makes it longer than the
slot count, and an out-of-slot index reached get_filament_config_index() and
came back as filament 0 - the clamp the bounds-checking was meant to remove.
Bound by the slot count instead; on the ordinary path the two are equal and
nothing changes. The is_extruder_used write gains the matching lower-bound
guard.
IMEXHelpers.hpp now states both halves of the rule its call sites follow.
Bound anything derived from the extruder map against the filament slot count
before using it as a filament id, not against the option about to be read.
And a miss is -1, which is a correct tool qualifier but matches no physical
head, so it cannot serve as a skip-the-primary sentinel: which head prints a
filament is answered by the filament and the map, never by a mode role,
since a primary-mode print may use any or all tools, one at a time.
The consequence is recorded there rather than left implicit. The two skip
sites skip nothing for a slot past the end of the map, so a plate with more
slots than nozzles double-writes the primary's pressure advance. It is
narrow and unreported, and a guard there would be a smaller change than
naming a head.
The header also records that RepRapFirmware sends an unqualified pressure
advance as M572 D0, naming drive 0 absolutely rather than the active tool.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Review findings on the preceding commit, plus one defect it should have
caught.
- The IDEX/IQEX pressure-advance loop fed resolve_filament_for_head()'s
result straight into enable_pressure_advance and pressure_advance. That
result is bounded by physical_extruder_map, which holds one entry per
NOZZLE, while both options are indexed per filament SLOT. On a printer
with more nozzles than the project has filaments the two spaces diverge
and get_at() clamped the overflow onto filament 0, emitting its pressure
advance on a secondary carriage. The second-layer temperature loop bounds the
same lookup, but against nozzle_temperature, which is variant-expanded and so
is not the slot count either -- it is not the precedent it looks like.
IMEXHelpers.hpp states the rule
once, and a test pins the contract that makes the bound necessary:
resolve_filament_for_head() answers in nozzle space, so a non-negative
result is not by itself safe to use as a filament id.
- The header claimed every caller renders a -1 tool qualifier as "emit
none". RepRapFirmware substitutes the historical D0 instead, deliberately
and with its own comment in GCodeWriter. Say so, rather than leaving a
contract a future author would code against.
- A cross-reference pointed at a hard-coded line number that the preceding
commit had itself shifted by nine lines. Name the function instead.
- The multi-color rejection reasons reach the user through Print::validate()
as raw English, while the returns on either side of them use L(). Wrap
them and register IMEXHelpers.cpp for extraction. They also still said
"IMEX", the internal name, so they move to IDEX/IQEX with the rest of the
user-facing strings rather than shipping the internal one to translators.
- Trim the preceding commit's comments. One block explained the same
clamping hazard six times; the canonical explanation now lives in
IMEXHelpers.hpp and the call sites point at it. The mode grid carried
twelve lines of commentary and no code, most of it archaeology already in
the commit message, and one claim about the modes editor that was not
true. The ArrangeJob threading note stays: it documents an invariant that
cannot be recovered from the code.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Review findings on the IDEX/IQEX parallel printing code, all in paths the
feature owns.
- physical_extruder_map lookups used ConfigOptionVector::get_at(), which
clamps an out-of-range index to values.front() rather than reporting a
miss. The map holds one entry per nozzle while filament ids index slots,
and nothing caps the slot count at the nozzle count, so a project authored
with more filaments than the printer has extruders silently addressed the
primary's head: pressure advance pinned to the wrong carriage, and
skip-primary loops suppressing whichever head sat at pem[0]. Bounds-check
at all four sites and treat the miss as "no mapping" (-1). Covered by a new
imex_pem_tool_for test; the header note now warns against get_at here.
- IMEXFilamentPickerPopover leaked a top-level window per ghost click:
wxPopupTransientWindow::Dismiss() only hides, and never reaches OnDismiss().
Destroy from an OnDismiss() override and dismiss the picker through
DismissAndNotify(), which is the path a successful pick takes.
- ArrangeJob read PartPlate's IMEX zone cache from the worker thread, where
a cache miss rebuilds GLModel members with no GL context current while the
GUI thread may be painting them. Snapshot the zones in prepare(), on the
main thread, already converted to plate-local coordinates.
- The mode grid anchored its row window to the Primary's gantry row. A window
as tall as the grid can only start at row 0, so this drew tiles for tools
that do not exist and hid real ones. Render the whole grid instead; a
Primary outside it is a data problem the zone layout already reports.
- Build the mode tooltip from one format string rather than two catalog
fragments concatenated around a runtime value, so translators can move the
mode name within the sentence, and register IMEXModesCtrl.cpp for string
extraction.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
* fix: bounds-check the toolchange flush-volume and HRC per-filament lookups
GCode::set_extruder's toolchange flush-volume lookup and
GCodeProcessor::update_slice_warnings's HRC check index per-filament and
per-extruder arrays (flush_volumes_matrix, the filament map, the nozzle list)
by filament/extruder id. When a config leaves one of those arrays shorter than
the filament count (partial or legacy multi-extruder projects, minimal
configs), the reads run off the end: silent on a normal STL, a hard abort under
_GLIBCXX_ASSERTIONS.
Route both reads through bounds checks: the flush lookup falls back to no flush,
matching the existing unknown-old-filament branch beside it, and the HRC check
skips an unmapped filament, mirroring the required_nozzle_HRC guard on the line
above. When the arrays are sized to the filament count the values are unchanged,
so correctly-specified configs are unaffected.
* ci: retrigger checks
* fix: guard H2C per-filament array reads against short config arrays
The H2C tool-ordering, wipe-tower, and g-code export paths index per-filament
config arrays by filament/tool id. A config with fewer entries than the filament
count (partial or legacy projects, minimal test configs) makes these reads run
past the end of the vector: silent under a normal STL, but UB that aborts under
the flatpak build's bounds-checked STL (_GLIBCXX_ASSERTIONS).
Route the reads through the existing clamping accessors (get_at,
get_filament_category, is_in_same_extruder) and add a small clamp helper for
filament_change_length. The guards are no-ops when the arrays are sized to the
filament count, so correctly specified configs are unaffected.
* fix: size the grouping context's filament_info to the filament count
build_filament_group_context built model_info.filament_info by walking
filament_type, so a config whose filament_type is shorter than the filament
count produced a short vector. FilamentGroup indexes filament_info by filament
id, so clamping the individual reads only moved the out-of-bounds access
downstream. Loop to filament_nums and read all three fields through get_at,
and drop filament_ids entries past the filament count, since the grouping code
pairs filament_ids and filament_info by position.
Adds a regression test with four filaments and one-entry filament_type /
filament_is_support. Without the fix it throws bad_alloc from copying a garbage
std::string read past the end.
* fix: guard the carousel nozzle-change length reads too
The carousel branch added in b90ac13d86/b0dddb4648 reads
m_filaments_change_length by tool id without a bounds check, the same
pattern this branch already routed through filament_change_length_at
a few lines above in both plan_toolchange and plan_tower_new.
* fix: guard WipeTower per-filament array reads against short config arrays
The BambuStudio WipeTower sync reintroduced raw per-filament array
indexing that reads out of bounds when a config leaves an array shorter
than the filament count: m_physical_extruder_map in format_line_M104/M109
(indexed even when empty), and m_filament_categories in get_wall_skip_points
and get_wall_filament_for_all_layer. Silent on a normal STL, a hard abort
under the bounds-checked STL the Flatpak build uses.
Bounds-check the physical extruder map before indexing (omitting the T
token, as the existing -1 path already does), and route the two raw
m_filament_categories reads through the clamping get_filament_category()
accessor the surrounding code already uses. No change for correctly-sized
configs.
Five sites carried a hardcoded fallback for imex_tools_per_gantry that had
to match the value registered in print_config_def, with nothing enforcing
the agreement, and several explanatory comments miscounted the sites they
described or cited stale line numbers.
Add imex_cfg_int/_float/_bool/_enum<T> to IMEXHelpers, which return the
value registered for the key when it is absent from the config, so the
registration is the single source and there is nothing left to keep in
sync. Route every read of the IMEX geometry keys through them: 32 call
sites across IMEXZones, PartPlate, GCodeViewer and Tab. The only direct
lookup left is the bail in PartPlate::imex_multicolor_block_reason, which
must not default because it reports a routing conflict and a defaulted
grid would produce a false warning.
imex_cfg_enum uses dynamic_cast on both halves rather than the type()
comparison the others use: every ConfigOptionEnum<T> reports coEnum, so a
type() check cannot tell one enum type from another and would cast a
ConfigOptionEnum<OtherEnum> to the requested T. The ConfigOptionPercent :
ConfigOptionFloat inheritance that rules dynamic_cast out for the float
accessor has no analogue for enums.
Correct the comments that prompted this: the cache-key input list in
PartPlate named five inputs for a nine-part key, the ImexMarkerKey note
in GCodeViewer called imex_tool_layout an input only the preview reads
when the plate keys it too, and four file:line citations pointed at the
wrong lines. Values are unchanged at every converted site; cache key
strings keep their existing representation.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
No IMEX code upstream, so nothing in this merge touches the feature. All 21 overlapping
files auto-resolved; verified every upstream addition is present in the merged tree.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Closes review comment 10.
`461c69c83e` settled this in April — IMEX internally, IDEX/IQEX as the user-facing label — but the
UI strings were never converted. Every translated string naming the feature now reads IDEX/IQEX:
41 occurrences across the printer and process option labels and tooltips, the modes editor, the
plate mode indicator, the pre-slice warnings, the placement refusals and the slicing errors. The
reviewer listed eight; the rest were in the same class.
Nothing else moves. The config keys keep the `imex_` spelling — `is_imex`, `imex_mode_names`,
`imex_parallel_mode` and the rest are on-disk format in existing printer presets and 3MF projects,
so renaming them would break every profile and project already saved. C++ identifiers, filenames,
comments and test names keep IMEX as well: it stays the internal name of the subsystem, which is
what covers the topology space (one gantry with 2-4 tools, 2x1 and 2x2 grids) that neither acronym
names on its own. Where a tooltip quotes a key, the key spelling is preserved and only the feature
word around it changed.
The `is_imex` tooltip is reworded rather than substituted: it already named the hardware families
parenthetically, so a literal replacement would have said IDEX/IQEX twice in one sentence.
No translation impact — no IMEX string had reached OrcaSlicer.pot or any catalogue, so there is
nothing to migrate. One test asserted on the old error text and now matches the new one.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Closes review comment 2, part of 18, and one non-IMEX regression the review did
not cover.
An imex_parallel_mode naming no entry in imex_mode_names still entered the
parallel branches. get_imex_active_tools() returned empty and the else was
skipped, so no head received its 1st-to-2nd layer temperature transition, and
imex_suppresses_bare_toolchange() still dropped the initial T<n> on the
expectation that a mode script would select the tool. validate() did not catch it
because its guard is declared_primary >= 0 and an unresolved mode yields -1. You
reach it by renaming a mode after a plate is set to it, or by opening a 3MF whose
printer preset names its modes differently. m_imex_parallel_mode is no longer
assigned before the lookup; a non-Primary name that matches no row now warns and
re-resolves against the Primary row, which is the fallback the PR description
already claimed. A mode that resolves to an empty tool roster takes the same path,
since the emitted G-code is wrong in the same way.
Warned rather than blocked: opening someone else's 3MF is a legitimate way to get
here and the Primary reading prints correctly, so refusing to slice would turn a
recoverable situation into a dead end. Silent was not an option either, because
the plate keeps showing the stale mode name while drawing no zones.
Separately, the 14 imex config keys all register non-nil defaults, so
append_full_config was emitting "; imex_* = <default>" into every exported
G-code, including on single-nozzle printers with nothing to do with the feature.
They are banned from the dump, matching the treatment already given to the
fast-purge, extruder-change and timelapse keys, so the config block is
byte-identical to the pre-IMEX baseline for the whole shipping fleet. Nothing
reads them back: GCodeProcessor has no imex reference, and the two per-plate keys
round-trip through the 3MF's model_settings.config on an independent path.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
* build: remove std::move that blocks copy elision
std::move wrapped around a temporary, or around a local being returned,
stops the compiler constructing it in place. Each edit is the fix clang
suggests, which is to delete the std::move call and keep its argument.
Three of the 39 sites save a move, the two return std::move(local) in
Print.cpp and TreeSupport.cpp:2749. The rest are equivalent either way
and match how the codebase already writes this elsewhere.
Clears 39 -Wpessimizing-move warnings.
* build: drop null checks on references and this
A reference cannot be bound to null and this cannot be null, so the
compiler folds these conditions to true and drops the guard. Seven are
if (&bitmap && bitmap.IsOk()), where IsOk() already does the work; two
test this directly. The guarded code runs either way, so removing the
dead operand changes nothing.
Clears 11 -Wundefined-bool-conversion warnings.
append_tcr2 scanned the tower's G-code for a "preheat T<n>" comment and rewrote
its S value to the interface temperature. Nothing it could match was ever there.
That comment has exactly one producer, GCodeProcessor's backtrace injector, and
that runs inside run_post_process() -- a pass over the finished, exported file.
append_tcr2 runs while the file is still being generated, so the text it looked
for did not exist yet and could not.
The loop therefore walked every line, matched none, and swapped the string for
an identical copy. Delete it.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
M104/M109 address a heater, but every caller of the instance
GCodeWriter::set_temperature overload addresses filaments by logical id, so on a
printer whose physical_extruder_map is not the identity the emitted T named the
wrong head -- or, where the logical id exceeds the head count, no head at all.
With a map of 0,0,0,0,1,2,3 a toolchange to filament 5 emitted "M109 S265 T4"
and "M104 S190 T4 ;cooldown" while the head it meant was T1.
Upstream already treats these commands as physical: the preheat it injects in
GCodeProcessor maps through the same map before emitting, and BBS's own wipe
tower does likewise. Emitting logical is the half that never got the memo.
That mismatch also disabled the cooldown suppression beside the preheat, which
compares the line's T against pem[tool_number] and so never matched a logical
one -- 171 cooldowns survived in a two-head print where none should have. Worse,
it could match the wrong line: a cooldown for filament 1 emitted T1, and a
toolchange to filament 5 gives pem[4] == 1, so a legitimate cooldown for head 0
was deleted because the incoming head happened to be numbered 1.
Translate once, in the instance overload every logical-space caller passes
through. The static overload is already physical-in and is left alone.
Gated on is_imex. physical_extruder_map carries two readings in this tree: the
BBS paths index it by extruder id, the IMEX paths by filament id, and the two
coincide only when the filament and nozzle counts match. Mapping unconditionally
would impose the IMEX reading on profiles that mean the other one --
fdm_bbl_3dp_002_common ships a non-identity [1,0], spared today only because
single_extruder_multi_material suppresses the T qualifier entirely.
The wipe tower's interface-temperature pass has to move with it. It strips the
M109 that post_toolchange emits by searching for that filament's tool index, so
it now searches for the mapped one; left alone it would have stopped matching,
and the surviving blocking M109 would have silently defeated the interface
temperature. Its sibling pass reads WipeTower2 output, which emits no T at all,
and is deliberately unchanged.
The bare T<n> toolchange stays logical -- it selects an AFC lane, not a heater.
Test slices two objects across a head boundary, the only case that reaches this
emission: the same-physical short-circuit in set_extruder suppresses the
cooldown entirely for lane swaps within one head. It scans every M104/M109
rather than matching fixed strings, so it catches any unmapped emission and not
just the two sites changed here. With the mapping neutered it reports 101
offending lines; with it in place, none.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Brings in 54 upstream commits, the bulk of them the BambuStudio-ported color
mixing / mixed filament subsystem (#15347) plus its follow-ups, along with the
Assimp-backed colored OBJ import, warning-policy build changes, and assorted
profile and localization updates.
Two conflicts, both "each side added at the same point", resolved by keeping
both:
- Print::validate() -- our IMEX multi-color block and upstream's new gradient
mixed filament warning were inserted at the same spot after the empty
extruders check. They test unrelated conditions, so both are kept, each with
its own closing brace.
- tests/libslic3r/test_3mf.cpp -- our three IMEX per-plate round-trip scenarios
and upstream's mixed-filament round-trip scenario both append to the end of
the file, and each side added one include. All four scenarios and both
includes are kept.
Everything else merged cleanly, including GCode.cpp, ToolOrdering.cpp,
PartPlate.cpp and PrintConfig.cpp. Upstream left the is_extruder_used block
untouched, so the IMEX supplement still applies, and estimate_wipe_tower_polygon
is unchanged, so the prime tower hull work is unaffected.
Not addressed here, and worth its own change: a mixed filament is a virtual slot
that no nozzle carries, while physical_extruder_map routes logical slots to
physical heads. Print::extruders() lists mixed slots under their own id whereas
tool_ordering.all_extruders() lists them post-expansion, so the IMEX pem lookups
have no defined answer for a mixed slot. Upstream's own guards reject a mixed
filament where a physical slot is required; IMEX likely wants the same.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
get_imex_active_tools returned every physical head named by the active mode's
tool string, including the one carrying the Primary role. The pressure-advance
and nozzle-temperature sites are already gated on the mode not being primary, so
only the is_extruder_used supplement was exposed.
In primary mode that supplement treated the mode's single declared tool as a
secondary carriage and marked its filament slot used, so machine_start_gcode
emitted a heat command for an extruder that never prints. The phantom slot
appears when the mode's declared tool differs from the head the initial tool
routes to through physical_extruder_map -- on an AFC/MMU layout, printing with a
filament that lives on any head other than the declared one.
Return an empty roster for primary mode, where there are no parallel carriages by
definition. This lives in the enumerator rather than at the call site because the
mode is already resolved and normalized there, and the two guarded callers cannot
reach it in that mode, so their behaviour is unchanged.
Scope: this closes the primary-mode instance. The same phantom slot still occurs
in a parallel mode when the initial tool's head is not the mode's declared
Primary, which turns on which of the two notions of "primary" the three emission
sites should skip. That question is unresolved and deliberately left alone here.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The IMEX branch of the 1st->2nd layer temperature transition is mutually
exclusive with the standard per-extruder path in its `else`, but it skipped the
head carrying the print's own toolpaths on the premise that "the standard
per-extruder temp path already addresses it". That path is the `else` branch and
never runs for a parallel mode, so the printing head received no transition at
all and held nozzle_temperature_initial_layer for the entire job.
Emit for every carriage the mode drives, the printing one included. The printing
head takes this layer's own filament; the parallel carriages, which carry no
toolpaths of their own, keep resolving through the per-plate head map with pem
inversion as the fallback. The lookup now goes through get_filament_config_index()
like the standard path, since a variant-expanded printer gives a filament its own
column and a raw index would read the wrong one.
Reproduced on a 4-carriage IQEX in copy mode: the only temperature command in the
whole file set the idle secondary carriage to the value it already had, while the
head doing the printing never left its first-layer temperature. The defect is
invisible whenever initial and regular temperatures match, which is why earlier
per-tool validation passed.
Tests cover both gantry counts, since the active set comes from the mode's tool
roster: an IDEX copy mode drives two carriages, an IQEX mode drives four, and the
IQEX case asserts a first-layer filament and a second-layer transition for each of
the four.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
set_extruder skips the ooze-prevention standby cool-down when the outgoing and
incoming filament route to the same physical extruder. That is an IMEX behaviour --
an AFC/MMU lane swap keeps the same heater selected -- but the check was not gated,
so it ran on every printer.
73 shipping profiles enable ooze_prevention by default (37 Snapmaker, 21 WonderMaker,
9 Flashforge, plus Lulzbot, Prusa, re3D, iQ and the MyToolChanger), and the 150
multi-nozzle machines behind them author no physical_extruder_map. They were spared
only because every one declares a single variant per extruder, so the map came out as
the identity and nothing was ever suppressed. Correctness should not rest on that.
Gate on is_imex. Verified on one fixture with only is_imex differing, with two
filaments mapped to the same physical extruder: 0 cool-downs emitted with it on, 26
with it off.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The placement clamps and the tower-approach router both stood in the bed's
bounding box for the bed itself, so on a delta or hexagonal bed the prime tower
could be parked in a corner that does not exist and the nozzle could be routed
across it. Both now test the real printable outline, slicing reports a tower
that does not fit instead of printing it off the bed, and a tower parked near an
edge is routed along the clamped side rather than falling back to a straight
line across the tower.
Also fixes the placement validation rotating the tower hull by degrees read as
radians about the plate origin, and never rotating the generated tower footprint
at all.
Adds a printer option that picks up the new tool without a blocking temperature
wait, travels to the wipe tower, and waits there right before purging, parked
beside the tower so the ooze from the heat-up lands next to it rather than on the
model. The incoming filament's target is raised ahead of the tool change, so the
heat-up overlaps both the change itself and the travel to the tower.
Off by default, and only offered for multi-extruder printers using a Type 2 wipe
tower; the generic toolchanger profile enables it.
* fixes: %g directive writing between 1 and 13 bytes into a region of size between 6 and 18 [-Wformat-overflow=]
* fixes: %5s directive writing between 5 and 63 bytes into a region of size 58 [-Wformat-overflow=]
* fixes: catching polymorphic type by value [-Wcatch-value=]
* fixes: [-Wcomment]; removes whitespaces
* increases buffer size from 71B to 90B to avoid potential ovfl.
* update snapmaker profiles. largely ported for Snapmaker Orca fork
* update prime volume
* set precise_outer_wall to 1
* Update per-material multi-tool ramming to the filament library
* Add per-filament overrides for toolchange retraction
* Set toolchange retraction per filament for Snapmaker U1
* set default support type to tree
* format snapmaker profiles
The tower travel took retract()'s default vertical Z hop instead of the
configured one, so the nozzle rose in place over the part and oozed
rather than departing with the travel. Pass the filament's z_hop_types
through, mapping Auto to a spiral lift as append_tcr does.
* Sync WipeTower from BambuStudio(through ca1881761)
* Fix post-slice self-invalidation on custom multi-extruder printers
* Complete the rib wipe tower port in WipeTower2
The rib tower is now always square (prime_tower_width is ignored, as the
GUI already implies), carries the rib origin offset like the BBL tower so
the rib tips sit inside the configured position, clamps the rib length to
the tower diagonal, and extends the ribs for short towers.
* Use the squared rib tower size in arrange estimates
estimate_wipe_tower_polygon reserved the arrange footprint and clamped the
tower X position with the raw prime_tower_width, under-reserving space
whenever the rib wall squares the tower to a different width.
* Print the WipeTower2 shell with a non-support, non-soluble filament
Like the BBL tower: the layer's sparse infill, wall, and brim go to the
first toolchange to a non-support/non-soluble filament, or are printed
with the incoming filament before any toolchange. The minimal-purge
clamp now also covers toolchanges that get no finish-layer saving.
Output is unchanged when no support/soluble filament is used.
* Port the skip-points gap wall to WipeTower2
prime_tower_skip_points was stubbed for Type2 towers: the wall call
hard-coded skip_points=false, the gap cutter received an empty vector,
and append_tcr2 never routed the entry travel. Now the toolchange entry
positions are precomputed from the finalized plan, the wall is cut open
at each entry, and the entry travel approaches around the tower bounding
box through the opening when it starts outside the tower. The geometry
helpers are re-synced with the BBL versions (add_extra_point guards,
per-point side selection). The cone wall keeps its separate path, where
the option stays inert.
Behavior change: non-BBL towers now honor the (default-on) checkbox with
gap walls and routed entries; with the option off the output is
unchanged, and the BBL tower path is untouched.
* Route the in-place toolchange tower entry through the skip-point gap
On multi-tool printers without ramming the tool changes away from the
tower and the entry travel is the tcr's own positioning move, which went
straight across the printed wall. Append the avoid-perimeter path to the
change-filament gcode instead, so the head approaches around the tower
and enters through the wall opening (append_tcr parity).
* Iron the purge start out through the skip-point gap in WipeTower2
Port the BBL tower's entry line ironing: extrude the first 3 mm of the
purge, retract, drag the nozzle 1.5x back out through the wall gap at
F600, creep back at F240 and unretract, so the toolchange start blob
ends up in the gap instead of on the wall. Fires only when the purge
starts at the left-edge entry heading right (in-place toolchangers);
SEMM ram/cooling wipes start mid-box and the priming line has no wall,
so both keep their previous output.
* Reserve WipeTower2 toolchange depth to match the printed purge
The planner reserved ramming rows gated only on enable_filament_ramming and
sized them with the SEMM 0.25s time step, while toolchange_Unload rams on
(semm && enable_filament_ramming) || filament_multitool_ramming with the
multitool time step. Disabling multitool ramming therefore left ~3 unprinted
rows per toolchange as blank bands in the tower. Without ramming the first
wipe line also needs reserved depth of its own (it no longer rides the last
ramming row), plus the y_step/2 offset the wipe start inherits from the
ramming start position - otherwise the tightened boxes truncate the ordered
purge at the box edge.
* Tile WipeTower2 purge rows contiguously across toolchange blocks
Without ramming, each purge block reserved one wipe pitch more than its
rows occupy (ceil+1 rounding plus the ram-geometry start offset), and the
wipe began a full pitch inside the block, leaving a blank band of exactly
two pitches between adjacent blocks. Plan the block as whole wipe rows,
start the first row so the row lattice continues across the block
boundary, and fill the reserved box instead of stopping at the ordered
volume, mirroring how the BBL WipeTower keeps planned depth identical to
printed rows. Ram-printing toolchanges (SEMM with ramming enabled,
multitool ramming) are unchanged.
* Scrub the WipeTower2 toolchange entry with the BBL flat-ironing spiral
The entry scrub now matches the BBL tower's toolchange_wipe_new sequence:
after the ironing drag the retracted nozzle runs a dry expanding-square
spiral centred on the wall-gap entry point before resuming the purge row.
The spiral runs whenever the gap wall is on (disable per filament via
filament_tower_ironing_area = 0); WipeTower2 no longer reads
prime_tower_flat_ironing.
* Restart the WipeTower2 wipe at the box boundary after multitool ramming
With the gap wall on a multi-tool printer, quantize the ram band up to its
whole reserved rows (as the BBL tower does for the old-tool purge) and start
CP TOOLCHANGE WIPE at the left-edge boundary on a fresh row below it instead
of continuing from wherever the ram serpentine ended. The entry scrub then
runs at the wall gap on ram toolchanges too, and the wipe box is whole rows,
so it is filled completely like the no-ram case. SEMM and skip-points-off
behavior is unchanged.
* Move the WipeTower2 wall gap to the wipe start row for ram toolchanges
* code cleanup
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* fix typo
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
On multi-tool printers without ramming the tool changes away from the
tower and the entry travel is the tcr's own positioning move, which went
straight across the printed wall. Append the avoid-perimeter path to the
change-filament gcode instead, so the head approaches around the tower
and enters through the wall opening (append_tcr parity).
Rodrigo Faselli