# Description
On multi-tool printers using the type 2 wipe tower, the travel to the
tower ignored the configured Z hop type and always used a plain vertical
hop, so the nozzle rose in place over the part and oozed instead of
lifting away with the travel. It now follows the filament's Z hop
setting, matching what the type 1 tower already does.
Only toolchange travels to a type 2 tower change. Normal Lift and z_hop
= 0 are unaffected, and no extrusion moves change in any mode.
# Screenshots/Recordings/Graphs
## Tests
<!--
> Please describe the tests that you have conducted to verify the
changes made in this PR.
-->
<!--
> A guide for users on how to download the artifacts from this PR.
-->
[How to Download Pull Requests Artifacts for
Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)
The tower travel took retract()'s default vertical Z hop instead of the
configured one, so the nozzle rose in place over the part and oozed
rather than departing with the travel. Pass the filament's z_hop_types
through, mapping Auto to a spiral lift as append_tcr does.
* Sync WipeTower from BambuStudio(through ca1881761)
* Fix post-slice self-invalidation on custom multi-extruder printers
* Complete the rib wipe tower port in WipeTower2
The rib tower is now always square (prime_tower_width is ignored, as the
GUI already implies), carries the rib origin offset like the BBL tower so
the rib tips sit inside the configured position, clamps the rib length to
the tower diagonal, and extends the ribs for short towers.
* Use the squared rib tower size in arrange estimates
estimate_wipe_tower_polygon reserved the arrange footprint and clamped the
tower X position with the raw prime_tower_width, under-reserving space
whenever the rib wall squares the tower to a different width.
* Print the WipeTower2 shell with a non-support, non-soluble filament
Like the BBL tower: the layer's sparse infill, wall, and brim go to the
first toolchange to a non-support/non-soluble filament, or are printed
with the incoming filament before any toolchange. The minimal-purge
clamp now also covers toolchanges that get no finish-layer saving.
Output is unchanged when no support/soluble filament is used.
* Port the skip-points gap wall to WipeTower2
prime_tower_skip_points was stubbed for Type2 towers: the wall call
hard-coded skip_points=false, the gap cutter received an empty vector,
and append_tcr2 never routed the entry travel. Now the toolchange entry
positions are precomputed from the finalized plan, the wall is cut open
at each entry, and the entry travel approaches around the tower bounding
box through the opening when it starts outside the tower. The geometry
helpers are re-synced with the BBL versions (add_extra_point guards,
per-point side selection). The cone wall keeps its separate path, where
the option stays inert.
Behavior change: non-BBL towers now honor the (default-on) checkbox with
gap walls and routed entries; with the option off the output is
unchanged, and the BBL tower path is untouched.
* Route the in-place toolchange tower entry through the skip-point gap
On multi-tool printers without ramming the tool changes away from the
tower and the entry travel is the tcr's own positioning move, which went
straight across the printed wall. Append the avoid-perimeter path to the
change-filament gcode instead, so the head approaches around the tower
and enters through the wall opening (append_tcr parity).
* Iron the purge start out through the skip-point gap in WipeTower2
Port the BBL tower's entry line ironing: extrude the first 3 mm of the
purge, retract, drag the nozzle 1.5x back out through the wall gap at
F600, creep back at F240 and unretract, so the toolchange start blob
ends up in the gap instead of on the wall. Fires only when the purge
starts at the left-edge entry heading right (in-place toolchangers);
SEMM ram/cooling wipes start mid-box and the priming line has no wall,
so both keep their previous output.
* Reserve WipeTower2 toolchange depth to match the printed purge
The planner reserved ramming rows gated only on enable_filament_ramming and
sized them with the SEMM 0.25s time step, while toolchange_Unload rams on
(semm && enable_filament_ramming) || filament_multitool_ramming with the
multitool time step. Disabling multitool ramming therefore left ~3 unprinted
rows per toolchange as blank bands in the tower. Without ramming the first
wipe line also needs reserved depth of its own (it no longer rides the last
ramming row), plus the y_step/2 offset the wipe start inherits from the
ramming start position - otherwise the tightened boxes truncate the ordered
purge at the box edge.
* Tile WipeTower2 purge rows contiguously across toolchange blocks
Without ramming, each purge block reserved one wipe pitch more than its
rows occupy (ceil+1 rounding plus the ram-geometry start offset), and the
wipe began a full pitch inside the block, leaving a blank band of exactly
two pitches between adjacent blocks. Plan the block as whole wipe rows,
start the first row so the row lattice continues across the block
boundary, and fill the reserved box instead of stopping at the ordered
volume, mirroring how the BBL WipeTower keeps planned depth identical to
printed rows. Ram-printing toolchanges (SEMM with ramming enabled,
multitool ramming) are unchanged.
* Scrub the WipeTower2 toolchange entry with the BBL flat-ironing spiral
The entry scrub now matches the BBL tower's toolchange_wipe_new sequence:
after the ironing drag the retracted nozzle runs a dry expanding-square
spiral centred on the wall-gap entry point before resuming the purge row.
The spiral runs whenever the gap wall is on (disable per filament via
filament_tower_ironing_area = 0); WipeTower2 no longer reads
prime_tower_flat_ironing.
* Restart the WipeTower2 wipe at the box boundary after multitool ramming
With the gap wall on a multi-tool printer, quantize the ram band up to its
whole reserved rows (as the BBL tower does for the old-tool purge) and start
CP TOOLCHANGE WIPE at the left-edge boundary on a fresh row below it instead
of continuing from wherever the ram serpentine ended. The entry scrub then
runs at the wall gap on ram toolchanges too, and the wipe box is whole rows,
so it is filled completely like the no-ram case. SEMM and skip-points-off
behavior is unchanged.
* Move the WipeTower2 wall gap to the wipe start row for ram toolchanges
* code cleanup
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* fix typo
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
# Description
<!--
> Please provide a summary of the changes made in this PR. Include
details such as:
> * What issue does this PR address or fix?
> * What new features or enhancements does this PR introduce?
> * Are there any breaking changes or dependencies that need to be
considered?
-->
This PR updates OTA vendor profile handling and fixes a Windows-only
startup race that could terminate OrcaSlicer silently.
## Changes
- Correct vendor profile version comparison logic.
- Trigger vendor profile synchronization after the startup printer
preset is restored.
- Remove duplicate vendor synchronization from the general startup
updater.
- Replace global temporary archive cleanup with targeted per-vendor
cleanup.
- Add updater-thread exception handling to prevent uncaught filesystem
errors from terminating the process.
# Screenshots/Recordings/Graphs
<!--
> Please attach relevant screenshots to showcase the UI changes.
> Please attach images that can help explain the changes.
-->
## Tests
<!--
> Please describe the tests that you have conducted to verify the
changes made in this PR.
-->
<!--
> A guide for users on how to download the artifacts from this PR.
-->
[How to Download Pull Requests Artifacts for
Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)
# Description
Python plugins currently have no way to localize their own dialogs to
match the app: the UI language is stored in `OrcaSlicer.conf`, which the
plugin audit hook deny-lists by design (the file sits next to cloud
secrets), and the host API exposes no app info. As a result, localized
plugins have to guess the language from the OS locale, which does not
always match the slicer UI (and the embedded interpreter often gets no
`LANG` at all in GUI sessions).
This PR adds a minimal read-only accessor:
```python
orca.host.app_language() # -> "en_US", "ru_RU", ...
```
It returns `GUI_App::current_language_code_safe()` — only the language
code string, nothing else from the config, so the audit-hook security
model is untouched.
No breaking changes; one file, +10 lines.
# Screenshots/Recordings/Graphs
(screenshots of the test dialog will be attached below)
## Tests
- Built on macOS (arm64, Ninja) with this change — compiles clean.
- Ran a minimal script-capability plugin calling
`orca.host.app_language()` on a system with Russian UI: the dialog shows
`'ru_RU'`.
- Guard before GUI init follows the same exception pattern as the
neighbouring `plater()`/`preset_bundle()` accessors.
<img width="903" height="826" alt="Снимок экрана 2026-07-28 в 23 10 48"
src="https://github.com/user-attachments/assets/27088265-b55d-4958-8602-7c3ab4993003"
/>
<img width="437" height="276" alt="Снимок экрана 2026-07-28 в 23 10 56"
src="https://github.com/user-attachments/assets/9845b401-dc8e-4353-aa24-5ace678270d6"
/>
With the gap wall on a multi-tool printer, quantize the ram band up to its
whole reserved rows (as the BBL tower does for the old-tool purge) and start
CP TOOLCHANGE WIPE at the left-edge boundary on a fresh row below it instead
of continuing from wherever the ram serpentine ended. The entry scrub then
runs at the wall gap on ram toolchanges too, and the wipe box is whole rows,
so it is filled completely like the no-ram case. SEMM and skip-points-off
behavior is unchanged.
The entry scrub now matches the BBL tower's toolchange_wipe_new sequence:
after the ironing drag the retracted nozzle runs a dry expanding-square
spiral centred on the wall-gap entry point before resuming the purge row.
The spiral runs whenever the gap wall is on (disable per filament via
filament_tower_ironing_area = 0); WipeTower2 no longer reads
prime_tower_flat_ironing.
Without ramming, each purge block reserved one wipe pitch more than its
rows occupy (ceil+1 rounding plus the ram-geometry start offset), and the
wipe began a full pitch inside the block, leaving a blank band of exactly
two pitches between adjacent blocks. Plan the block as whole wipe rows,
start the first row so the row lattice continues across the block
boundary, and fill the reserved box instead of stopping at the ordered
volume, mirroring how the BBL WipeTower keeps planned depth identical to
printed rows. Ram-printing toolchanges (SEMM with ramming enabled,
multitool ramming) are unchanged.
The planner reserved ramming rows gated only on enable_filament_ramming and
sized them with the SEMM 0.25s time step, while toolchange_Unload rams on
(semm && enable_filament_ramming) || filament_multitool_ramming with the
multitool time step. Disabling multitool ramming therefore left ~3 unprinted
rows per toolchange as blank bands in the tower. Without ramming the first
wipe line also needs reserved depth of its own (it no longer rides the last
ramming row), plus the y_step/2 offset the wipe start inherits from the
ramming start position - otherwise the tightened boxes truncate the ordered
purge at the box edge.
Plugins have no way to localize their own dialogs: the UI language lives in
OrcaSlicer.conf, which the plugin audit hook deny-lists because the file sits
next to cloud secrets. Add a read-only host accessor that returns just the
language code (current_language_code_safe), so plugins can match the app
language without touching the config file.
Port the BBL tower's entry line ironing: extrude the first 3 mm of the
purge, retract, drag the nozzle 1.5x back out through the wall gap at
F600, creep back at F240 and unretract, so the toolchange start blob
ends up in the gap instead of on the wall. Fires only when the purge
starts at the left-edge entry heading right (in-place toolchangers);
SEMM ram/cooling wipes start mid-box and the priming line has no wall,
so both keep their previous output.
* For dialog without explicitly `SetMinSize`, we should use `SetSizerAndFit` instead, otherwise the dialog will not show correctly on GTK3. (OrcaSlicer/OrcaSlicer#14561)
- and if `SetSizer` is called before the full layout has been built, then an extra `SetSizeHints` should be called before layout/fit so the min size can be properly set automatically based on children's min sizes accordingly.
* Fix GTK3 dialog min size: SetSizer → SetSizerAndFit for dialogs without explicit SetMinSize
Replace SetSizer() with SetSizerAndFit() in 11 dialog constructors that
neither call SetMinSize() nor SetSizeHints(), ensuring proper minimum
size propagation from child widgets on GTK3.
SetSizerAndFit internally calls sizer->SetSizeHints(window), which
sets the window's minimum size based on children — the same fix
applied to ProjectDropDialog in 8a7662083e.
Also drop sizer->Fit(this) calls where present, since they only
resize but don't set the min size hint needed by GTK3.
Co-Authored-By: Claude <noreply@anthropic.com>
* Update code style
* Update TroubleshootDialog.hpp
* Fix unsaved preset dialog layout
* Fix MsgDialog layout
* Fix other 3 instances in MsgDialog.cpp
* Fix a few more instances
* Fix printer option dialog too big on Windows
---------
Co-authored-by: Claude <noreply@anthropic.com>
Co-authored-by: yw4z <ywsyildiz@gmail.com>
On multi-tool printers without ramming the tool changes away from the
tower and the entry travel is the tcr's own positioning move, which went
straight across the printed wall. Append the avoid-perimeter path to the
change-filament gcode instead, so the head approaches around the tower
and enters through the wall opening (append_tcr parity).
prime_tower_skip_points was stubbed for Type2 towers: the wall call
hard-coded skip_points=false, the gap cutter received an empty vector,
and append_tcr2 never routed the entry travel. Now the toolchange entry
positions are precomputed from the finalized plan, the wall is cut open
at each entry, and the entry travel approaches around the tower bounding
box through the opening when it starts outside the tower. The geometry
helpers are re-synced with the BBL versions (add_extra_point guards,
per-point side selection). The cone wall keeps its separate path, where
the option stays inert.
Behavior change: non-BBL towers now honor the (default-on) checkbox with
gap walls and routed entries; with the option off the output is
unchanged, and the BBL tower path is untouched.
Like the BBL tower: the layer's sparse infill, wall, and brim go to the
first toolchange to a non-support/non-soluble filament, or are printed
with the incoming filament before any toolchange. The minimal-purge
clamp now also covers toolchanges that get no finish-layer saving.
Output is unchanged when no support/soluble filament is used.
estimate_wipe_tower_polygon reserved the arrange footprint and clamped the
tower X position with the raw prime_tower_width, under-reserving space
whenever the rib wall squares the tower to a different width.
The rib tower is now always square (prime_tower_width is ignored, as the
GUI already implies), carries the rib origin offset like the BBL tower so
the rib tips sit inside the configured position, clamps the rib length to
the tower diagonal, and extends the ribs for short towers.
* Add wxInspector dep
* Initial intergration of wxInspector
* docs: add wxInspector plugins design spec
Design spec for two wxInspector plugins (DPIAware + CustomWidgets) that expose
OrcaSlicer's custom control properties in the inspector property grid.
Covers: DPIAware scale-factor properties, Button, CheckBox, TextInput,
SwitchButton, ProgressBar, Label, and LabeledStaticBox.
* docs: add wxInspector plugins implementation plan
6-task plan covering: source changes to existing widget headers,
DPIAwarePlugin, CustomWidgetsPlugin, registration helper,
MainFrame/CMake wiring, and build verification.
* feat: add getters/setters for wxInspector plugin access
Add minimal public accessors to DPIAware (set_scale_factor,
set_prev_scale_factor, set_em_unit, force_rescale), Button
(GetStyle, GetType, IsSelected), CheckBox (IsHalfChecked),
TextInput (GetCornerRadius), and LabeledStaticBox
(GetCornerRadius, GetBorderWidth, GetBorderColor, GetScale).
* feat: add wxInspector plugin registration helper
Add RegisterOrcaInspectorPlugins() inline function that creates
and registers the DPIAwarePlugin and CustomWidgetsPlugin as
static instances (matching wxInspector's built-in pattern).
* feat: add DPIAware wxInspector plugin
Exposes DPI scaling properties (scale_factor, prev_scale_factor,
em_unit, normal_font, force_rescale) on DPIFrame and DPIDialog
widgets. Uses dynamic_cast for detection and a template helper
to capture the correct static type for lambda accessors.
* feat: add OrcaCustomWidgets wxInspector plugin
Exposes Orca-specific properties on 7 widget types:
- Button: Style, Type, Selected
- CheckBox: Half Checked
- TextInput: Label, Text Value, Corner Radius
- SwitchButton: Value
- ProgressBar: Proportion, Show Number
- Label: Is Hyperlink, Font Point Size
- LabeledStaticBox: Corner Radius, Border Width, Border Color, Scale
Each widget type uses dynamic_cast for safe detection.
* feat: wire wxInspector plugins into MainFrame and build
Call RegisterOrcaInspectorPlugins() in MainFrame constructor after
SetupInspectorAccelerator(). Add all 5 plugin source files to
SLIC3R_GUI_SOURCES in CMakeLists.txt.
* fix: move plugin registration to GUI_App::on_init_inner
Register plugins once in app init rather than in MainFrame
constructor, which may be recreated during the application
lifetime.
* fix: include plugin headers in Registration.hpp for complete types
Static locals require complete type. Include DPIAwarePlugin.hpp and
CustomWidgetsPlugin.hpp instead of forward-declaring. Also remove
unused include from MainFrame.cpp (registration moved to GUI_App).
* fix: qualify DPIFrame/DPIDialog with Slic3r::GUI namespace
* Make DPIDialog inspectable. For other dialogs, we will add them if necessary later.
* docs: add spec for moving wxInspectable into DPIAware template
Move wxInspector::wxInspectable base class from DPIDialog and MainFrame
into the common DPIAware<P> template, making all DPIAware widgets
automatically visible in the inspector tree.
Co-Authored-By: Claude <noreply@anthropic.com>
* docs: add implementation plan for moving wxInspectable into DPIAware
Co-Authored-By: Claude <noreply@anthropic.com>
* docs: update spec/plan — move SetupInspectorAccelerator into DPIAware too
Co-Authored-By: Claude <noreply@anthropic.com>
* refactor: move wxInspectable and SetupInspectorAccelerator into DPIAware
DPIAware<P> now inherits wxInspector::wxInspectable and calls
SetupInspectorAccelerator in its constructor, making all DPIAware
widgets automatically appear in the inspector tree with the
Ctrl+Shift+I shortcut. DPIDialog now uses 'using' to inherit the
constructor. Remove redundant wxInspectable inheritance and
SetupInspectorAccelerator calls from DPIDialog and MainFrame.
Co-Authored-By: Claude <noreply@anthropic.com>
* fix: use LB_HYPERLINK constant instead of magic number 0x0020
Co-Authored-By: Claude <noreply@anthropic.com>
* Clean up
* Fix Linux build
* Don't build wxInspector sample
* Use shallow clone
* Try fix flatpak build
* Attempt to fix build again
* Fix build failure caused by 436c16135e
* wxWidgets build only download required submodules
* This should fix build on Windows on ARM
* Enable PIC
* Disable layout inspector by default for public release
* Use wxInspector 1.0.0 release
---------
Co-authored-by: Claude <noreply@anthropic.com>
