mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-10-04 14:20:58 +00:00
Make U1 filament notes readable without commit references
Co-authored-by: Codex <codex@openai.com>
This commit is contained in:
Eric McCann
@@ -17,6 +17,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"16"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"16"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"16"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"11"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11 mm^3/s, from Snorca standard preset Generic PETG-CF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11 mm^3/s, from Snorca standard preset Generic PETG-CF (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"11.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"11.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"1.6"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Generic PLA @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Generic PLA @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"18"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"18"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"18"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"7.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"7.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -17,6 +17,6 @@
|
||||
"7.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"3.2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"3.2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -17,6 +17,6 @@
|
||||
"3.2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"15"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Polymaker General PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Polymaker General PLA Family @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Silk PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Silk PLA Family @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Tough PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Tough PLA Family @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -45,6 +45,6 @@
|
||||
"280"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ABS @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ABS @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -45,6 +45,6 @@
|
||||
"0.02"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ASA @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ASA @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,6 +24,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -63,6 +63,6 @@
|
||||
"0.035"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 30 mm^3/s, from Snorca HF preset Snapmaker PETG HF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 30 mm^3/s, from Snorca HF preset Snapmaker PETG HF (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,6 +24,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,6 +24,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"1"
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"0.05"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 10 mm^3/s, from Snorca HF preset Snapmaker PETG Translucent @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 10 mm^3/s, from Snorca HF preset Snapmaker PETG Translucent @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"10"
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"16"
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"16"
|
||||
|
||||
+1
-1
@@ -60,6 +60,6 @@
|
||||
"0.028"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PETG-CF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PETG-CF @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"15"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Snapmaker PLA Basic @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Snapmaker PLA Basic @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,7 +24,7 @@
|
||||
"0.024"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 15 mm^3/s, from Snorca HF preset Snapmaker PLA Full Spectrum @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 15 mm^3/s, from Snorca HF preset Snapmaker PLA Full Spectrum @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"15"
|
||||
|
||||
+1
-1
@@ -21,6 +21,6 @@
|
||||
"0.023"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PLA Glow @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PLA Glow @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -27,6 +27,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -39,6 +39,6 @@
|
||||
"0.024"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA Matte @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA Matte @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -27,6 +27,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -27,6 +27,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -18,6 +18,6 @@
|
||||
"Slope Lift"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Silk @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Silk @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"10"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"10"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -18,6 +18,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -21,6 +21,6 @@
|
||||
"0.024"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA SnapSpeed @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA SnapSpeed @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -18,6 +18,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -18,6 +18,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.2 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"1.6"
|
||||
|
||||
+1
-1
@@ -12,7 +12,7 @@
|
||||
"0.024"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Translucent @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Translucent @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"12"
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"12"
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"12"
|
||||
|
||||
+1
-1
@@ -21,6 +21,6 @@
|
||||
"0.024"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA Wood @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA Wood @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -18,6 +18,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -15,7 +15,7 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"20"
|
||||
|
||||
+1
-1
@@ -33,6 +33,6 @@
|
||||
"0.02"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA-CF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA-CF @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,6 +24,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -24,6 +24,6 @@
|
||||
"1"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -21,6 +21,6 @@
|
||||
"0.6"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 6 mm^3/s, from Snorca HF preset Snapmaker PVA @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer for 0.4 mm nozzles. Volumetric speed ceiling: 6 mm^3/s, from Snorca HF preset Snapmaker PVA @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -12,7 +12,7 @@
|
||||
"0.9506"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"6"
|
||||
|
||||
@@ -12,7 +12,7 @@
|
||||
"0.9312"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from Snapmaker OrcaSlicer. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
],
|
||||
"filament_max_volumetric_speed": [
|
||||
"6"
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"3.2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"3.2"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"3.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.5 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.5 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"9"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 9 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 9 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"12"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
+1
-1
@@ -12,6 +12,6 @@
|
||||
"16"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -12,6 +12,6 @@
|
||||
"10.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.4 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -12,6 +12,6 @@
|
||||
"10.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.6 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
@@ -12,6 +12,6 @@
|
||||
"10.5"
|
||||
],
|
||||
"filament_notes": [
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
"Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.8 nozzle (Snapmaker OrcaSlicer). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament."
|
||||
]
|
||||
}
|
||||
|
||||
Reference in New Issue
Block a user