mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-11-21 22:01:55 +00:00
* Add PrintaLot PETG profiles for Bambu Lab printers
* Remove redundant PETG defaults after independent review
* Declare PrintaLot PETG's own values on its base
The type, 255 °C and the 17 mm³/s limit are PrintaLot's values, not the
library's PETG defaults, so they should not change if fdm_filament_pet
does. filament_type is also part of the filament_id.
* Drop PrintaLot PETG values Bambu Lab printers never read
- The multitool ramming values: only the Type 2 prime tower reads them,
and Bambu Lab printers always use Type 1.
- volumetric_speed_coefficients: only read with adaptive volumetric
speed, which is off.
- filament_retract_length_nc outside the H2C: only the H2C's
change-filament G-code reads it.
- retraction_distances_when_ec where long retraction on extruder change
is off.
- filament_preheat_temperature_delta outside the H2C: only used on
printers with several nozzles per extruder.
- filament_flush_temp_fast 0 and filament_extruder_variant
"Direct Drive Standard": both are the defaults.
* Move values shared by the PrintaLot PETG presets to the base
The 17 mm³/s limit and slow_down_min_speed are the same in every preset
except the 0.2 nozzles (1 mm³/s) and the A2L 0.2 nozzle (40 mm/s), and
most presets write the same placeholder filament start and end G-code.
Presets with other values keep their own.
* bump OrcaFilamentLibrary.json
---------
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
(cherry picked from commit 7374b734d3)
109 lines
1.6 KiB
JSON
109 lines
1.6 KiB
JSON
{
|
|
"type": "filament",
|
|
"name": "PrintaLot PETG @base",
|
|
"inherits": "fdm_filament_pet",
|
|
"from": "system",
|
|
"filament_id": "OFdndO9v",
|
|
"instantiation": "false",
|
|
"close_additional_fan_first_x_layers": [
|
|
"3"
|
|
],
|
|
"cool_plate_temp": [
|
|
"0"
|
|
],
|
|
"cool_plate_temp_initial_layer": [
|
|
"0"
|
|
],
|
|
"eng_plate_temp": [
|
|
"70"
|
|
],
|
|
"eng_plate_temp_initial_layer": [
|
|
"70"
|
|
],
|
|
"fan_cooling_layer_time": [
|
|
"30"
|
|
],
|
|
"fan_max_speed": [
|
|
"90"
|
|
],
|
|
"fan_min_speed": [
|
|
"40"
|
|
],
|
|
"filament_adhesiveness_category": [
|
|
"300"
|
|
],
|
|
"filament_dev_ams_drying_ams_limitations": [
|
|
"1",
|
|
"0"
|
|
],
|
|
"filament_dev_ams_drying_heat_distortion_temperature": [
|
|
"75"
|
|
],
|
|
"filament_dev_ams_drying_temperature": [
|
|
"65",
|
|
"65",
|
|
"55",
|
|
"55"
|
|
],
|
|
"filament_dev_ams_drying_time": [
|
|
"12",
|
|
"12",
|
|
"12",
|
|
"12"
|
|
],
|
|
"filament_dev_chamber_drying_bed_temperature": [
|
|
"80"
|
|
],
|
|
"filament_dev_chamber_drying_time": [
|
|
"12.0"
|
|
],
|
|
"filament_dev_drying_cooling_temperature": [
|
|
"55"
|
|
],
|
|
"filament_dev_drying_softening_temperature": [
|
|
"60"
|
|
],
|
|
"filament_end_gcode": [
|
|
"; filament end gcode \n\n"
|
|
],
|
|
"filament_flow_ratio": [
|
|
"0.95"
|
|
],
|
|
"filament_max_volumetric_speed": [
|
|
"17"
|
|
],
|
|
"filament_notes": [
|
|
"PrintaLot PETG, 1.75 mm."
|
|
],
|
|
"filament_start_gcode": [
|
|
"; filament start gcode\n"
|
|
],
|
|
"filament_type": [
|
|
"PETG"
|
|
],
|
|
"filament_vendor": [
|
|
"PrintaLot"
|
|
],
|
|
"nozzle_temperature": [
|
|
"255"
|
|
],
|
|
"nozzle_temperature_initial_layer": [
|
|
"255"
|
|
],
|
|
"nozzle_temperature_range_high": [
|
|
"270"
|
|
],
|
|
"overhang_fan_speed": [
|
|
"90"
|
|
],
|
|
"overhang_fan_threshold": [
|
|
"10%"
|
|
],
|
|
"slow_down_layer_time": [
|
|
"12"
|
|
],
|
|
"slow_down_min_speed": [
|
|
"20"
|
|
]
|
|
}
|