mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-09-16 13:32:44 +00:00
115 lines
1.8 KiB
JSON
115 lines
1.8 KiB
JSON
{
|
|
"type": "filament",
|
|
"name": "Generic TPU @Prusa CORE One",
|
|
"inherits": "fdm_filament_flex",
|
|
"renamed_from": "Prusa Generic TPU @CORE One;Prusa Generic TPU CORE One",
|
|
"from": "system",
|
|
"setting_id": "jsXqf9CeaXCvsrWM",
|
|
"filament_id": "OFgbpcy9",
|
|
"instantiation": "true",
|
|
"chamber_temperature": [
|
|
"30"
|
|
],
|
|
"close_fan_the_first_x_layers": [
|
|
"3"
|
|
],
|
|
"compatible_printers": [
|
|
"Prusa CORE One 0.25 nozzle",
|
|
"Prusa CORE One 0.3 nozzle",
|
|
"Prusa CORE One 0.4 nozzle",
|
|
"Prusa CORE One 0.5 nozzle",
|
|
"Prusa CORE One HF 0.4 nozzle",
|
|
"Prusa CORE One HF 0.5 nozzle"
|
|
],
|
|
"fan_cooling_layer_time": [
|
|
"100"
|
|
],
|
|
"fan_max_speed": [
|
|
"50"
|
|
],
|
|
"fan_min_speed": [
|
|
"30"
|
|
],
|
|
"filament_cost": [
|
|
"82"
|
|
],
|
|
"filament_density": [
|
|
"1.22"
|
|
],
|
|
"filament_deretraction_speed": [
|
|
"20"
|
|
],
|
|
"filament_diameter": [
|
|
"1.75"
|
|
],
|
|
"filament_end_gcode": [
|
|
"; Filament-specific end gcode"
|
|
],
|
|
"filament_flow_ratio": [
|
|
"1.08"
|
|
],
|
|
"filament_max_volumetric_speed": [
|
|
"2.5"
|
|
],
|
|
"filament_minimal_purge_on_wipe_tower": [
|
|
"15"
|
|
],
|
|
"filament_notes": [
|
|
""
|
|
],
|
|
"filament_retraction_length": [
|
|
"2.5"
|
|
],
|
|
"filament_retraction_minimum_travel": [
|
|
"2"
|
|
],
|
|
"filament_retraction_speed": [
|
|
"60"
|
|
],
|
|
"filament_soluble": [
|
|
"0"
|
|
],
|
|
"filament_start_gcode": [
|
|
"M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
|
|
],
|
|
"filament_type": [
|
|
"TPU"
|
|
],
|
|
"filament_vendor": [
|
|
"Generic"
|
|
],
|
|
"filament_wipe": [
|
|
"0"
|
|
],
|
|
"filament_z_hop": [
|
|
"0"
|
|
],
|
|
"hot_plate_temp": [
|
|
"50"
|
|
],
|
|
"hot_plate_temp_initial_layer": [
|
|
"50"
|
|
],
|
|
"idle_temperature": [
|
|
"150"
|
|
],
|
|
"nozzle_temperature": [
|
|
"230"
|
|
],
|
|
"nozzle_temperature_initial_layer": [
|
|
"230"
|
|
],
|
|
"overhang_fan_speed": [
|
|
"70"
|
|
],
|
|
"reduce_fan_stop_start_freq": [
|
|
"1"
|
|
],
|
|
"slow_down_layer_time": [
|
|
"10"
|
|
],
|
|
"slow_down_min_speed": [
|
|
"15"
|
|
]
|
|
}
|