Clamp Ironing Line Spacing to a Usable Minimum

An ironing line spacing of 0 reached the fillers from a 3MF, the CLI or
the per-filament override, which has no GUI guard. Concentric ironing
then never finished slicing, because a zero inset never shrinks the
region, and rectilinear ironing was silently dropped. Tiny positive
values produced an unprintable number of lines.

Top surface and support ironing now clamp the spacing to the 0.05 mm
floor the process GUI guard already enforces, so these configurations
iron at that spacing. Spacings at or above the floor, including every
shipped profile, are unchanged. The concentric filler also returns early
on a non-positive step so no other caller can hang it, and the filament
settings page now resets a too-small override the same way the process
page does.

src/libslic3r/Fill/Fill.cpp

@@ -1692,9 +1692,9 @@ void Layer::make_ironing()
 				ironing_params.just_infill 	= false;
 				// ORCA: Get filament-specific overrides if configured, otherwise use process values
 				size_t extruder_idx = ironing_params.extruder - 1;
-				ironing_params.line_spacing = (!config.filament_ironing_spacing.is_nil(extruder_idx)
+				ironing_params.line_spacing = std::max(IRONING_SPACING_MIN, !config.filament_ironing_spacing.is_nil(extruder_idx)
 					? config.filament_ironing_spacing.get_at(extruder_idx)
-					: config.ironing_spacing);
+					: config.ironing_spacing.value);
                 ironing_params.inset = (!config.filament_ironing_inset.is_nil(extruder_idx)
 					? config.filament_ironing_inset.get_at(extruder_idx)
 					: config.ironing_inset);

src/libslic3r/Fill/FillConcentric.cpp

@@ -22,6 +22,9 @@ void FillConcentric::_fill_surface_single(
     
     coord_t min_spacing = scale_(this->spacing) * params.multiline;
     coord_t distance = coord_t(min_spacing / params.density);
+    // A non-positive step never shrinks the region, so the inset loop below would not end.
+    if (min_spacing <= 0 || distance <= 0)
+        return;
     
     if (params.density > 0.9999f && !params.dont_adjust) {
         distance = this->_adjust_solid_spacing(bounding_box.size()(0), distance);
@@ -108,6 +111,8 @@ void FillConcentric::_fill_surface_single(const FillParams& params,
     // no rotation is supported for this infill pattern
     Point   bbox_size = expolygon.contour.bounding_box().size();
     coord_t min_spacing = scaled<coord_t>(this->spacing);
+    if (min_spacing <= 0)
+        return;
 
     if (params.density > 0.9999f && !params.dont_adjust) {
         coord_t                loops_count = std::max(bbox_size.x(), bbox_size.y()) / min_spacing + 1;

src/libslic3r/PrintConfig.hpp

@@ -178,6 +178,10 @@ enum class IroningType {
     Count,
 };
 
+// Smallest usable ironing line spacing. Anything tighter yields an unprintable number of lines,
+// and zero stops the fillers from making progress.
+constexpr double IRONING_SPACING_MIN = 0.05;
+
 //BBS
 enum class WallInfillOrder {
     InnerOuterInfill,

src/libslic3r/Support/SupportParameters.hpp

@@ -64,7 +64,7 @@ struct SupportParameters {
 
         this->ironing = object_config.support_ironing;
         this->ironing_flow = support_material_interface_flow.with_height(support_material_interface_flow.height() * 0.01 * object_config.support_ironing_flow.value);
-        this->ironing_spacing = object_config.support_ironing_spacing;
+        this->ironing_spacing = std::max(IRONING_SPACING_MIN, object_config.support_ironing_spacing.value);
         this->ironing_pattern = object_config.support_ironing_pattern;
 
         // Calculate a minimum support layer height as a minimum over all extruders, but not smaller than 10um.

src/slic3r/GUI/ConfigManipulation.cpp

@@ -210,6 +210,30 @@ void ConfigManipulation::check_filament_max_volumetric_speed(DynamicPrintConfig
 
 }
 
+void ConfigManipulation::check_filament_ironing_spacing(DynamicPrintConfig *config)
+{
+    const auto *opt = config->option<ConfigOptionFloatsNullable>("filament_ironing_spacing");
+    if (opt == nullptr)
+        return;
+    std::vector<double> values = opt->values;
+    bool                reset  = false;
+    for (size_t i = 0; i < values.size(); ++i)
+        if (!opt->is_nil(i) && values[i] < IRONING_SPACING_MIN) {
+            values[i] = 0.1;
+            reset     = true;
+        }
+    if (!reset)
+        return;
+    const wxString     msg_text = _(L("Ironing spacing too small\nIt has been reset to 0.1"));
+    MessageDialog      dialog(nullptr, msg_text, "", wxICON_WARNING | wxOK);
+    DynamicPrintConfig new_conf = *config;
+    is_msg_dlg_already_exist    = true;
+    dialog.ShowModal();
+    new_conf.set_key_value("filament_ironing_spacing", new ConfigOptionFloatsNullable(values));
+    apply(config, &new_conf);
+    is_msg_dlg_already_exist = false;
+}
+
 void ConfigManipulation::check_chamber_temperature(DynamicPrintConfig* config)
 {
    bool support_chamber_temp_control=GUI::wxGetApp().preset_bundle->printers.get_selected_preset().config.opt_bool("support_chamber_temp_control");
@@ -332,7 +356,7 @@ void ConfigManipulation::update_print_fff_config(DynamicPrintConfig* config, con
     }
 
     //BBS: ironing_spacing shouldn't be too small or equal to zero
-    if (config->opt_float("ironing_spacing") < 0.05)
+    if (config->opt_float("ironing_spacing") < IRONING_SPACING_MIN)
     {
         const wxString msg_text = _(L("Ironing spacing too small\nIt has been reset to 0.1"));
         MessageDialog dialog(nullptr, msg_text, "", wxICON_WARNING | wxOK);
@@ -343,7 +367,7 @@ void ConfigManipulation::update_print_fff_config(DynamicPrintConfig* config, con
         apply(config, &new_conf);
         is_msg_dlg_already_exist = false;
     }
-    if (config->opt_float("support_ironing_spacing") < 0.05)
+    if (config->opt_float("support_ironing_spacing") < IRONING_SPACING_MIN)
     {
         const wxString msg_text = _(L("Ironing spacing too small\nIt has been reset to 0.1"));
         MessageDialog dialog(nullptr, msg_text, "", wxICON_WARNING | wxOK);

src/slic3r/GUI/ConfigManipulation.hpp

@@ -84,6 +84,7 @@ public:
     void    check_nozzle_temperature_initial_layer_range(DynamicPrintConfig* config);
     void    check_adaptive_pressure_advance_model(DynamicPrintConfig* config);
     void    check_filament_max_volumetric_speed(DynamicPrintConfig *config);
+    void    check_filament_ironing_spacing(DynamicPrintConfig *config);
     void    check_chamber_temperature(DynamicPrintConfig* config);
     void    check_chamber_minimal_temperature(DynamicPrintConfig* config);
     bool    check_layer_height(DynamicPrintConfig* config);

src/slic3r/GUI/Tab.cpp

@@ -4905,6 +4905,7 @@ void TabFilament::update()
         return; // ys_FIXME
 
     m_config_manipulation.check_filament_max_volumetric_speed(m_config);
+    m_config_manipulation.check_filament_ironing_spacing(m_config);
 
     m_update_cnt++;
 

src/slic3r/GUI/UserManager.cpp

@@ -31,15 +31,14 @@ int UserManager::parse_json(std::string payload)
 {
     bool restored_json = false;
     json j;
-
-    //bind/unbind
-
-    try {
     json j_pre = json::parse(payload);
     if (j_pre.empty()) {
         return -1;
     }
 
+    //bind/unbind
+
+    try {
         if (j_pre.contains("bind")) {
             if (j_pre["bind"].contains("command")) {
 

src/slic3r/Utils/Duet.cpp

@@ -274,4 +274,13 @@ bool Duet::start_print(wxString &msg, const std::string &filename, ConnectionTyp
 	return res;
 }
 
+int Duet::get_err_code_from_body(const std::string &body) const
+{
+	pt::ptree root;
+	std::istringstream iss (body); // wrap returned json to istringstream
+	pt::read_json(iss, root);
+
+	return root.get<int>("err", 0);
+}
+
 }

src/slic3r/Utils/Duet.hpp

@@ -40,6 +40,7 @@ private:
 	ConnectionType connect(wxString &msg) const;
 	void disconnect(ConnectionType connectionType) const;
 	bool start_print(wxString &msg, const std::string &filename, ConnectionType connectionType, bool simulationMode) const;
+	int get_err_code_from_body(const std::string &body) const;
 };
 
 }

src/slic3r/Utils/ESP3D.cpp

@@ -146,6 +146,15 @@ bool ESP3D::start_print(wxString& msg, const std::string& filename) const
     return ret;
 }
 
+int ESP3D::get_err_code_from_body(const std::string& body) const
+{
+    pt::ptree          root;
+    std::istringstream iss(body); // wrap returned json to istringstream
+    pt::read_json(iss, root);
+
+    return root.get<int>("err", 0);
+}
+
 // ESP3D only accepts 8.3 filenames else it crashes marlin and other undefined behaviour
 std::string ESP3D::get_short_name(const std::string& filename) const
 {

src/slic3r/Utils/ESP3D.hpp

@@ -33,6 +33,7 @@ private:
     std::string m_console_port;
 
     bool        start_print(wxString& msg, const std::string& filename) const;
+    int         get_err_code_from_body(const std::string& body) const;
     std::string get_short_name(const std::string& filename) const;
     std::string format_command(const std::string& path, const std::string& arg, const std::string& val) const;
 };

src/slic3r/Utils/Flashforge.cpp

@@ -510,22 +510,12 @@ bool Flashforge::fetch_material_slots(std::vector<FlashforgeMaterialSlot>& slots
     if (!request_local_api_json("detail", json{{"serialNumber", m_serial_number}, {"checkCode", m_check_code}}.dump(), body, msg))
         return false;
 
-    if (!parse_material_slots(body, slots, supports_material_station)) {
+    const auto parsed = json::parse(body, nullptr, false, true);
+    if (parsed.is_discarded()) {
         msg = _(L("Flashforge returned an invalid JSON response."));
         return false;
     }
 
-    return true;
-}
-
-bool Flashforge::parse_material_slots(const std::string& body, std::vector<FlashforgeMaterialSlot>& slots, bool* supports_material_station)
-{
-    slots.clear();
-
-    const auto parsed = json::parse(body, nullptr, false, true);
-    if (parsed.is_discarded())
-        return false;
-
     const auto& detail = parsed.contains("detail") ? parsed["detail"] : parsed;
     const auto& station = detail.contains("matlStationInfo") ? detail["matlStationInfo"] :
                           detail.contains("MatlStationInfo") ? detail["MatlStationInfo"] : json();
@@ -552,21 +542,12 @@ bool Flashforge::parse_material_slots(const std::string& body, std::vector<Flash
     if (supports_material_station != nullptr)
         *supports_material_station = reports_material_station;
 
-    // Fields are read leniently: firmware may send numbers as strings or flags as numbers.
     for (const auto& slot : slot_infos) {
-        if (!slot.is_object())
-            continue;
         FlashforgeMaterialSlot info;
-        info.slot_id = static_cast<int>(slots.size()) + 1;
+        info.slot_id        = slot.value("slotId", static_cast<int>(slots.size()) + 1);
-        if (const auto it = slot.find("slotId"); it != slot.end())
+        info.has_filament   = slot.value("hasFilament", false);
-            try_parse_json_int(*it, info.slot_id);
+        info.material_name  = slot.value("materialName", std::string());
-        int has_filament = 0;
+        info.material_color = slot.value("materialColor", std::string());
-        if (const auto it = slot.find("hasFilament"); it != slot.end() && try_parse_json_int(*it, has_filament))
-            info.has_filament = has_filament != 0;
-        if (const auto it = slot.find("materialName"); it != slot.end() && it->is_string())
-            info.material_name = it->get<std::string>();
-        if (const auto it = slot.find("materialColor"); it != slot.end() && it->is_string())
-            info.material_color = it->get<std::string>();
         slots.emplace_back(std::move(info));
     }
 
@@ -689,4 +670,13 @@ std::string Flashforge::extract_host_name() const
     return out;
 }
 
+int Flashforge::get_err_code_from_body(const std::string& body) const
+{
+    pt::ptree          root;
+    std::istringstream iss(body); // wrap returned json to istringstream
+    pt::read_json(iss, root);
+
+    return root.get<int>("err", 0);
+}
+
 } // namespace Slic3r

src/slic3r/Utils/Flashforge.hpp

@@ -45,8 +45,6 @@ public:
     PrintHostPostUploadActions get_post_upload_actions() const override { return PrintHostPostUploadAction::StartPrint; }
     std::string                get_host() const override { return m_host; }
     bool                       fetch_material_slots(std::vector<FlashforgeMaterialSlot>& slots, bool* supports_material_station, wxString& msg) const;
-    // Parses a local API "detail" reply. Returns false when the body is not valid JSON.
-    static bool                parse_material_slots(const std::string& body, std::vector<FlashforgeMaterialSlot>& slots, bool* supports_material_station);
     static bool                discover_printers(std::vector<FlashforgeDiscoveredPrinter>& printers, wxString& msg, int timeout_ms = 10000, int idle_timeout_ms = 1500, int max_retries = 3);
 
 private:
@@ -70,6 +68,7 @@ private:
     bool request_local_api_json(const std::string& path, const std::string& body, std::string& response_body, wxString& error_msg) const;
     std::string make_http_url(const std::string& path) const;
     std::string extract_host_name() const;
+    int  get_err_code_from_body(const std::string &body) const;
     bool connect(wxString& msg) const;
     bool start_print(wxString& msg, const std::string& filename) const;
 };

src/slic3r/Utils/MKS.cpp

@@ -141,4 +141,13 @@ bool MKS::start_print(wxString& msg, const std::string& filename) const
 	return ret;
 }
 
+int MKS::get_err_code_from_body(const std::string& body) const
+{
+	pt::ptree root;
+	std::istringstream iss(body); // wrap returned json to istringstream
+	pt::read_json(iss, root);
+
+	return root.get<int>("err", 0);
+}
+
 } // Slic3r

src/slic3r/Utils/MKS.hpp

@@ -34,6 +34,7 @@ private:
 
 	std::string get_upload_url(const std::string& filename) const;
 	bool start_print(wxString& msg, const std::string& filename) const;
+	int get_err_code_from_body(const std::string& body) const;
 };
 
 }

src/slic3r/Utils/PrintHost.cpp

@@ -3,13 +3,10 @@
 #include <vector>
 #include <thread>
 #include <exception>
-#include <sstream>
 #include <boost/optional.hpp>
 #include <boost/log/trivial.hpp>
 #include <boost/filesystem.hpp>
 #include <nlohmann/json.hpp>
-#include <boost/property_tree/ptree.hpp>
-#include <boost/property_tree/json_parser.hpp>
 
 #include <wx/string.h>
 #include <wx/app.h>
@@ -175,20 +172,6 @@ std::string moonraker_error_reason(const std::string &body)
 
 } // namespace
 
-int PrintHost::get_err_code_from_body(const std::string &body)
-{
-    boost::property_tree::ptree root;
-    std::istringstream iss(body);
-    try {
-        boost::property_tree::read_json(iss, root);
-    } catch (const std::exception &ex) {
-        BOOST_LOG_TRIVIAL(error) << "PrintHost: response is not valid JSON: " << ex.what();
-        return -1;
-    }
-
-    return root.get<int>("err", 0);
-}
-
 wxString PrintHost::format_error(const std::string &body, const std::string &error, unsigned status) const
 {
     if (status != 0) {
@@ -432,10 +415,12 @@ void PrintHostJobQueue::priv::remove_source()
     source_to_remove.clear();
 }
 
-bool PrintHostJobQueue::upload_job(PrintHostJob &job, PrintHost::ProgressFn progress_fn, PrintHost::ErrorFn error_fn, PrintHost::InfoFn info_fn)
+void PrintHostJobQueue::priv::perform_job(PrintHostJob the_job)
 {
+    emit_progress(0);   // Indicate the upload is starting
+
     // Captured before upload_data is moved into upload() below.
-    const std::string upload_filename = job.upload_data.source_path.filename().string();
+    const std::string upload_filename = the_job.upload_data.source_path.filename().string();
 
     {
         LifecycleEventContext ctx;
@@ -444,37 +429,19 @@ bool PrintHostJobQueue::upload_job(PrintHostJob &job, PrintHost::ProgressFn prog
         fire_lifecycle_event(LifecycleEvent::UploadStarted, ctx);
     }
 
-    bool success = false;
+    bool success = the_job.printhost->upload(std::move(the_job.upload_data),
-    std::string error;
+        [this](Http::Progress progress, bool &cancel)   { this->progress_fn(std::move(progress), cancel); },
-    // A throwing upload must not stop the worker, or later jobs would stay queued forever.
+        [this](wxString error)                          { this->error_fn(std::move(error)); },
-    try {
+        [this](wxString tag, wxString host)             { this->info_fn(std::move(tag), std::move(host)); }
-        success = job.printhost->upload(std::move(job.upload_data), std::move(progress_fn), error_fn, std::move(info_fn));
+    );
-    } catch (const std::exception &e) {
-        error = e.what();
-        error_fn(error);
-    }
 
     {
         LifecycleEventContext ctx;
         ctx.name  = upload_filename;
         ctx.code  = success ? LifecycleEvtCode::Ok : LifecycleEvtCode::Error;
-        ctx.msg   = error;
         fire_lifecycle_event(LifecycleEvent::UploadFinished, ctx);
     }
 
-    return success;
-}
-
-void PrintHostJobQueue::priv::perform_job(PrintHostJob the_job)
-{
-    emit_progress(0);   // Indicate the upload is starting
-
-    bool success = PrintHostJobQueue::upload_job(the_job,
-        [this](Http::Progress progress, bool &cancel)   { this->progress_fn(std::move(progress), cancel); },
-        [this](wxString error)                          { this->error_fn(std::move(error)); },
-        [this](wxString tag, wxString host)             { this->info_fn(std::move(tag), std::move(host)); }
-    );
-
     if (success) {
         emit_progress(100);
         if (the_job.switch_to_device_tab) {

src/slic3r/Utils/PrintHost.hpp

@@ -87,8 +87,6 @@ public:
 
     static PrintHost* get_print_host(DynamicPrintConfig *config);
     static std::string get_print_host_webui(DynamicPrintConfig *config);
-    // Reads the "err" field of a JSON reply, 0 when absent. Returns -1 when the body is not valid JSON.
-    static int get_err_code_from_body(const std::string &body);
 
     //Support for cloud webui login
     virtual bool is_cloud() const { return false; }
@@ -152,10 +150,6 @@ public:
     void enqueue(PrintHostJob job);
     void cancel(size_t id);
 
-    // Uploads the job, firing UploadStarted and a matching UploadFinished. An exception thrown by
-    // the upload is reported through error_fn and makes the upload fail.
-    static bool upload_job(PrintHostJob &job, PrintHost::ProgressFn progress_fn, PrintHost::ErrorFn error_fn, PrintHost::InfoFn info_fn);
-
 private:
     struct priv;
     std::shared_ptr<priv> p;

src/slic3r/Utils/UltiMaker.cpp

@@ -654,4 +654,13 @@ bool UltiMaker::start_print(wxString &msg, const std::string &filename, Connecti
 	return res;
 }
 
+int UltiMaker::get_err_code_from_body(const std::string &body) const
+{
+	pt::ptree root;
+	std::istringstream iss (body); // wrap returned json to istringstream
+	pt::read_json(iss, root);
+
+	return root.get<int>("err", 0);
+}
+
 }

src/slic3r/Utils/UltiMaker.hpp

@@ -64,6 +64,7 @@ private:
 	void set_auth(Http& http) const;
 	void disconnect(ConnectionType connectionType) const;
 	bool start_print(wxString &msg, const std::string &filename, ConnectionType connectionType) const;
+	int get_err_code_from_body(const std::string &body) const;
 };
 
 }

tests/fff_print/test_fill.cpp

@@ -747,6 +747,61 @@ TEST_CASE("A region with ironing turned off is never ironed", "[Fill]")
     REQUIRE(Layer::choose_ironing_extruder(cfg, spiral_mode, /*is_topmost_layer=*/true) == -1);
 }
 
+// Ironing path count and total length in mm, over the whole object.
+static std::pair<size_t, double> ironing_extent(const Print &print)
+{
+    size_t paths  = 0;
+    double length = 0.;
+    for (const Layer *layer : print.objects().front()->layers())
+        for (const LayerRegion *region : layer->regions())
+            for (const ExtrusionEntity *entity : region->fills.flatten().entities)
+                if (ironing_role(entity->role())) {
+                    ++paths;
+                    length += unscale<double>(entity->length());
+                }
+    return {paths, length};
+}
+
+TEST_CASE("Ironing spacing below the minimum irons at the minimum spacing", "[Fill]")
+{
+    const std::string pattern      = GENERATE("rectilinear", "concentric");
+    const bool        via_filament = GENERATE(false, true);
+    const double      spacing      = GENERATE(0., 0.001);
+    CAPTURE(pattern, via_filament, spacing);
+
+    auto ironing_for = [&pattern, via_filament](double spacing) {
+        DynamicPrintConfig config = DynamicPrintConfig::full_print_config();
+        config.set_deserialize_strict({{"ironing_type", "top"},
+                                       {"ironing_pattern", pattern},
+                                       {"layer_height", 0.2}});
+        // The filament override replaces the process spacing, which stays at a usable value.
+        if (via_filament)
+            config.set_deserialize_strict({{"ironing_spacing", 0.1}, {"filament_ironing_spacing", spacing}});
+        else
+            config.set_deserialize_strict({{"ironing_spacing", spacing}});
+        Print print;
+        Slic3r::Test::init_and_process_print({Slic3r::Test::cube(20)}, print, config);
+        return ironing_extent(print);
+    };
+
+    const std::pair<size_t, double> clamped = ironing_for(spacing);
+    const std::pair<size_t, double> minimum = ironing_for(IRONING_SPACING_MIN);
+    REQUIRE(minimum.first > 0);
+    CHECK(clamped.first == minimum.first);
+    CHECK_THAT(clamped.second, Catch::Matchers::WithinRel(minimum.second, 1e-9));
+}
+
+TEST_CASE("Concentric fill at zero spacing returns without paths", "[Fill]")
+{
+    std::unique_ptr<Fill> filler(Fill::new_from_type(ipConcentric));
+    filler->spacing      = 0.;
+    filler->bounding_box = BoundingBox(Point(0, 0), Point::new_scale(10, 10));
+    FillParams params;
+    params.density = 1.f;
+    Surface surface(stTop, ExPolygon({Point(0, 0), Point::new_scale(10, 0), Point::new_scale(10, 10), Point::new_scale(0, 10)}));
+    CHECK(filler->fill_surface(&surface, params).empty());
+}
+
 TEST_CASE("Solid infill direction offsets every layer when no template is set", "[Fill]")
 {
     auto angles_for = [](int direction) {

tests/slic3rutils/CMakeLists.txt

@@ -25,7 +25,6 @@ add_executable(${_TEST_NAME}_tests
     test_plugin_cloud_metadata.cpp
     test_plugin_audit.cpp
     test_shortcuts.cpp
-    test_user_manager.cpp
     ../fff_print/test_helpers.cpp
     )
 

tests/slic3rutils/test_printhost.cpp

@@ -1,15 +1,8 @@
 #include <catch2/catch_all.hpp>
 
-#include <memory>
-#include <stdexcept>
-#include <string>
-#include <vector>
-
 #include <nlohmann/json.hpp>
 
-#include "libslic3r/LifecycleEvents.hpp"
 #include "slic3r/Utils/PrintHost.hpp"
-#include "slic3r/Utils/Flashforge.hpp"
 
 using namespace Slic3r;
 
@@ -31,41 +24,6 @@ public:
     std::string get_host() const override { return {}; }
 };
 
-class ThrowingPrintHost : public TestPrintHost
-{
-public:
-    bool upload(PrintHostUpload, ProgressFn, ErrorFn, InfoFn) const override { throw std::runtime_error("reply could not be read"); }
-};
-
-struct UploadEvents
-{
-    std::vector<LifecycleEvent>   events;
-    std::vector<LifecycleEvtCode> codes;
-    std::vector<std::string>      errors;
-    bool                          uploaded{false};
-
-    explicit UploadEvents(std::unique_ptr<PrintHost> host)
-    {
-        set_lifecycle_hook_fn([this](LifecycleEvent event, const LifecycleEventContext& ctx) {
-            events.push_back(event);
-            codes.push_back(ctx.code);
-        });
-
-        PrintHostJob job;
-        job.printhost               = std::move(host);
-        job.upload_data.source_path = "plate.gcode";
-        try {
-            uploaded = PrintHostJobQueue::upload_job(job, [](Http::Progress, bool&) {},
-                                                     [this](wxString error) { errors.push_back(error.ToStdString()); },
-                                                     [](wxString, wxString) {});
-        } catch (...) {
-            set_lifecycle_hook_fn(nullptr);
-            throw;
-        }
-        set_lifecycle_hook_fn(nullptr);
-    }
-};
-
 std::string format_error(const std::string& body, const std::string& error, unsigned status)
 {
     return TestPrintHost().format_error(body, error, status).ToStdString();
@@ -88,14 +46,6 @@ std::string moonraker_error(int code, const std::string& message, const std::str
 constexpr const char* k_busy_file_403 =
     R"JSON({"error": {"code": 403, "message": "Forbidden", "traceback": "Traceback (most recent call last):\n\n  File \"/home/lava/moonraker/moonraker/components/file_manager/file_manager.py\", line 1017, in _finish_gcode_upload\n    can_start = self._handle_operation_check(check_path)\n                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^\n\nmoonraker.utils.exceptions.ServerError: File currently in use\n\nDuring handling of the above exception, another exception occurred:\n\nTraceback (most recent call last):\n\n  File \"/home/lava/moonraker/moonraker/components/application.py\", line 1069, in post\n    raise tornado.web.HTTPError(\ntornado.web.HTTPError: HTTP 403: Forbidden (File is loaded, upload not permitted)\n"}})JSON";
 
-// Replies a print host can send instead of JSON: a proxy or login page, nothing, a cut-off body.
-const std::vector<std::string> non_json_replies = {
-    "<html><body>proxy login required</body></html>",
-    "",
-    "{\"err\":",
-    "{\"detail\":{\"matlStationInfo\":{\"slotInfos\":[{\"slotId\":1,",
-};
-
 } // namespace
 
 TEST_CASE("A Klipper upload error shows its reason instead of a Python traceback", "[PrintHost][Regression]")
@@ -261,114 +211,3 @@ TEST_CASE("Error bodies that are not a Moonraker envelope are left unchanged", "
         CHECK(format_error("", "curl:Could not connect", 0) == "curl:Could not connect");
     }
 }
-
-TEST_CASE("Print host error code is read from a JSON reply", "[PrintHost]")
-{
-    CHECK(PrintHost::get_err_code_from_body(R"({"err":0})") == 0);
-    CHECK(PrintHost::get_err_code_from_body(R"({"err":2})") == 2);
-    CHECK(PrintHost::get_err_code_from_body(R"({"status":"ok"})") == 0);
-}
-
-TEST_CASE("Print host error code reports a reply that is not JSON as an error", "[PrintHost]")
-{
-    const std::string body = GENERATE(from_range(non_json_replies));
-    int err = 0;
-    REQUIRE_NOTHROW(err = PrintHost::get_err_code_from_body(body));
-    CHECK(err != 0);
-}
-
-TEST_CASE("Print host error code tolerates a wrongly typed err field", "[PrintHost]")
-{
-    const std::string body = GENERATE(as<std::string>{}, R"({"err":"busy"})", R"({"err":{"code":1}})", R"([1,2])");
-    CHECK_NOTHROW(PrintHost::get_err_code_from_body(body));
-}
-
-TEST_CASE("Flashforge material slots are read from a well-formed reply", "[PrintHost][Flashforge]")
-{
-    const std::string body = R"({"code":0,"detail":{"hasMatlStation":true,"matlStationInfo":{"slotCnt":2,"slotInfos":[
-        {"slotId":1,"hasFilament":true,"materialName":"PLA","materialColor":"#FFFFFF"},
-        {"slotId":2,"hasFilament":false,"materialName":"","materialColor":""}]}}})";
-
-    std::vector<FlashforgeMaterialSlot> slots;
-    bool supports_station = false;
-    REQUIRE(Flashforge::parse_material_slots(body, slots, &supports_station));
-    CHECK(supports_station);
-    REQUIRE(slots.size() == 2);
-    CHECK(slots[0].slot_id == 1);
-    CHECK(slots[0].has_filament);
-    CHECK(slots[0].material_name == "PLA");
-    CHECK(slots[0].material_color == "#FFFFFF");
-    CHECK(slots[1].slot_id == 2);
-    CHECK_FALSE(slots[1].has_filament);
-}
-
-TEST_CASE("Flashforge material slots accept numbers as strings and flags as numbers", "[PrintHost][Flashforge]")
-{
-    const std::string body = R"({"detail":{"matlStationInfo":{"slotInfos":[
-        {"slotId":"3","hasFilament":1,"materialName":null,"materialColor":7}]}}})";
-
-    std::vector<FlashforgeMaterialSlot> slots;
-    REQUIRE_NOTHROW(Flashforge::parse_material_slots(body, slots, nullptr));
-    REQUIRE(slots.size() == 1);
-    CHECK(slots[0].slot_id == 3);
-    CHECK(slots[0].has_filament);
-    CHECK(slots[0].material_name.empty());
-    CHECK(slots[0].material_color.empty());
-}
-
-TEST_CASE("Flashforge material slots skip entries that are not objects", "[PrintHost][Flashforge]")
-{
-    const std::string body = R"({"detail":{"matlStationInfo":{"slotInfos":[5,"slot",null,[],
-        {"slotId":4,"hasFilament":true,"materialName":"PETG"}]}}})";
-
-    std::vector<FlashforgeMaterialSlot> slots;
-    REQUIRE_NOTHROW(Flashforge::parse_material_slots(body, slots, nullptr));
-    REQUIRE(slots.size() == 1);
-    CHECK(slots[0].slot_id == 4);
-    CHECK(slots[0].material_name == "PETG");
-}
-
-TEST_CASE("Flashforge material slots tolerate slot info that is not a list", "[PrintHost][Flashforge]")
-{
-    const std::string body = GENERATE(as<std::string>{},
-                                      R"({"detail":{"matlStationInfo":{"slotInfos":5}}})",
-                                      R"({"detail":{"matlStationInfo":{"slotInfos":"none"}}})",
-                                      R"({"detail":{"matlStationInfo":7}})",
-                                      R"({"detail":"offline"})");
-
-    std::vector<FlashforgeMaterialSlot> slots;
-    bool ok = false;
-    REQUIRE_NOTHROW(ok = Flashforge::parse_material_slots(body, slots, nullptr));
-    CHECK(ok);
-    CHECK(slots.empty());
-}
-
-TEST_CASE("Flashforge material slots reject a reply that is not JSON", "[PrintHost][Flashforge]")
-{
-    const std::string body = GENERATE(from_range(non_json_replies));
-    std::vector<FlashforgeMaterialSlot> slots;
-    bool ok = true;
-    REQUIRE_NOTHROW(ok = Flashforge::parse_material_slots(body, slots, nullptr));
-    CHECK_FALSE(ok);
-    CHECK(slots.empty());
-}
-
-TEST_CASE("An upload that throws still finishes with an error", "[PrintHost][LifecycleEvents]")
-{
-    UploadEvents run(std::make_unique<ThrowingPrintHost>());
-
-    CHECK_FALSE(run.uploaded);
-    CHECK(run.errors == std::vector<std::string>{"reply could not be read"});
-    CHECK(run.events == std::vector<LifecycleEvent>{LifecycleEvent::UploadStarted, LifecycleEvent::UploadFinished});
-    CHECK(run.codes == std::vector<LifecycleEvtCode>{LifecycleEvtCode::Ok, LifecycleEvtCode::Error});
-}
-
-TEST_CASE("A successful upload finishes without an error", "[PrintHost][LifecycleEvents]")
-{
-    UploadEvents run(std::make_unique<TestPrintHost>());
-
-    CHECK(run.uploaded);
-    CHECK(run.errors.empty());
-    CHECK(run.events == std::vector<LifecycleEvent>{LifecycleEvent::UploadStarted, LifecycleEvent::UploadFinished});
-    CHECK(run.codes == std::vector<LifecycleEvtCode>{LifecycleEvtCode::Ok, LifecycleEvtCode::Ok});
-}

tests/slic3rutils/test_user_manager.cpp

@@ -1,23 +0,0 @@
-#include <catch2/catch_all.hpp>
-
-#include <string>
-
-#include "slic3r/GUI/UserManager.hpp"
-
-using namespace Slic3r;
-
-TEST_CASE("User message that is not JSON is rejected without throwing", "[UserManager]")
-{
-    const std::string payload = GENERATE(as<std::string>{}, "not json", "", "<html></html>", "{\"bind\":");
-    UserManager manager;
-    int result = 0;
-    REQUIRE_NOTHROW(result = manager.parse_json(payload));
-    CHECK(result == -1);
-}
-
-TEST_CASE("User message without a successful bind is ignored", "[UserManager]")
-{
-    const std::string payload = GENERATE(as<std::string>{}, "{}", R"({"bind":{"command":"unbind"}})", R"({"bind":"bind"})", "[1]");
-    UserManager manager;
-    CHECK(manager.parse_json(payload) == -1);
-}