Keep the Scarf Seam Free of Sub-Millimetre Segments

A scarf joint split the loop at exactly the scarf length, so the remainder
of the segment the split landed in became the first flat segment, often a
fraction of a millimetre. The seam insertion also leaves segments of a few
micrometres at both ends of the loop, which a scarf extrudes through where a
plain loop would start or stop. With junction deviation the planner treats
such short moves as tight corners, limited by the Z axis acceleration at the
end of the ramp, and slows to a third of the wall speed or nearly halts at
the seam.

Extend the ramp to the next vertex when the remainder would be shorter than
half a scarf step, capped at a millimetre, beyond which planners treat a move
as ordinary; the scarf only grows, never shrinks. Drop the vertex next to the
seam point at either end when that segment is shorter than an eighth of a
common line width, so the loop still starts and ends at the seam; a trimmed
path loses its arc fitting and prints as line segments. Clamp the scarf
length to the trimmed loop so a scarf covering a whole loop still ends at
full flow. The descending pass reuses the same path, so both wedges stay
consistent, and a flat part that would collapse to a single point is dropped.

.claude/skills/orca-profiles/references/naming.md

@@ -35,10 +35,9 @@ toolhead, a multi-material build) may drop the suffix — still an exact referen
 ## `process`
 
 `<layer height>mm <quality> @<target>` — [process-profiles.md](process-profiles.md#naming) has the
-quality ladder and the `fdm_process_*` base names. The quality label stays before `@` and the printer
-target after it: a printer model in the quality slot leaves the tier undescribed. The `@<target>` is a
-human label, not a reference: it usually does not equal a real variant, and compatibility comes from the
-resolved `compatible_printers` list or condition.
+quality ladder and the `fdm_process_*` base names. The `@<target>` is a human label, not a reference: it
+usually does not equal a real variant, and compatibility comes from the resolved `compatible_printers`
+list or condition.
 
 ## `filament`
 
@@ -59,30 +58,6 @@ to the first `@`; the target half is a label except for reserved forms:
   chosen at runtime
   ([color is a runtime property](filament-profiles.md#color-is-a-runtime-property)).
 
-## Checking names
-
-Check every newly added profile's `name` against its type and role: model, selectable preset or base.
-Apply the same checks to an intentional name change. The human-readable naming shapes are not enforced
-by `check`: inspect the added or renamed profiles in the diff, using neighbouring names as context and
-following the bundle's established style where the type-specific conventions allow variation.
-
-For bases (`instantiation: "false"`), use the type-specific conventions:
-
-| Type | Base names |
-| --- | --- |
-| `machine` | `fdm_machine_common`, `fdm_<vendor>_common`, or an established machine-family base name |
-| `process` | `fdm_process_*`, including shared roots and per-layer-height / per-nozzle bases such as `fdm_process_single_0.20` |
-| `filament` | `fdm_filament_*` material roots or `<Product> @base` product roots |
-
-Shared base names across bundles are intentional, including product roots such as `Fiberon PA6-CF @base`.
-Investigate a newly authored base that retains an unrelated selectable preset's name from a copy.
-
-**Name uniqueness is checked by CI.** `check_preset_name_uniqueness` checks type + name within each
-bundle. `check_machine_model_name_uniqueness` checks model names across the entire tree, even with
-`--vendor`: `Preset::get_printer_type` matches `printer_model` against all vendors' models and returns
-the first match, so a duplicate makes lookup depend on vendor order. Both run as part of
-`python3 scripts/orca_profile_tool.py check`.
-
 ## Not the same as the filename
 
 The loader keys off `name`, and a filename that disagrees usually still loads. Index `name` must equal the

.claude/skills/orca-profiles/references/review-checklist.md

@@ -17,7 +17,6 @@ The table highlights gaps that need human review. What CI *does* run:
 | A `renamed_from` whose old name is still a live preset | The redirect is inert while a live preset carries that name |
 | A preset differentiated only by color, or an all-printer library preset without `@System` | Per-color presets split one product across ids and the selector fills with near-duplicates; CI stays green |
 | Per-extruder vector length on a multi-nozzle printer | Silently padded (with the **first** value) or truncated |
-| A name that ignores its type's convention — a model in a `process` quality slot, or an unrelated target label left in a copied preset | The selector misrepresents the preset's quality or intended printer |
 
 ## 1. Was the vendor `version` bumped?
 
@@ -170,15 +169,6 @@ vendor, and a filename that disagrees with the preset's `name` (common; the load
 Check for Windows-invalid characters, reserved device names, trailing path-component spaces/dots,
 and case mismatches in `sub_path` or asset paths. See [cross-platform paths](validation.md#cross-platform-paths).
 
-## 16. Do the preset names follow the conventions?
-
-Check **every newly added profile and intentional name change**, including models and bases,
-against [the naming conventions](naming.md#checking-names). Preserve shipped names during
-ordinary tuning; renaming a shipped selectable preset requires the migration in item 4.
-
-*Why:* CI checks name uniqueness, but does not enforce the naming conventions. Catch naming
-mistakes before the names ship and existing projects depend on them.
-
 ---
 
 ## Reporting the review

.github/workflows/build_all.yml

@@ -413,14 +413,6 @@ jobs:
         GH_TOKEN: ${{ github.token }}
       run: |
         api="$GITHUB_API_URL/repos/$GITHUB_REPOSITORY/actions/caches"
-        # The save step reports success even when its tar failed, so keep
-        # the older entries unless the new one is listed.
-        if ! curl -sSf -H "Authorization: Bearer $GH_TOKEN" \
-            "$api?ref=$GITHUB_REF&key=$CCACHE_ENTRY" \
-            | jq -e --arg entry "$CCACHE_ENTRY" 'any(.actions_caches[]; .key == $entry)' > /dev/null; then
-          echo "$CCACHE_ENTRY was not saved; keeping the older entries."
-          exit 0
-        fi
         curl -sSf -H "Authorization: Bearer $GH_TOKEN" \
           "$api?ref=$GITHUB_REF&key=ccache-$CCACHE_LEG-&per_page=100" \
           | jq -r --arg prefix "ccache-$CCACHE_LEG-" --argjson run "$GITHUB_RUN_ID" \

.github/workflows/build_orca.yml

@@ -798,13 +798,6 @@ jobs:
         env:
           GH_TOKEN: ${{ github.token }}
         run: |
-          # The save step reports success even when its tar failed, so keep
-          # the older entries unless the new one is listed.
-          if ! gh cache list --ref "$GITHUB_REF" --key "$CCACHE_ENTRY" --json key \
-              | jq -e --arg entry "$CCACHE_ENTRY" 'any(.[]; .key == $entry)' > /dev/null; then
-            echo "$CCACHE_ENTRY was not saved; keeping the older entries."
-            exit 0
-          fi
           gh cache list --ref "$GITHUB_REF" --key "ccache-$CCACHE_LEG-" --limit 100 --json id,key \
             | jq -r --arg prefix "ccache-$CCACHE_LEG-" --argjson run "$GITHUB_RUN_ID" \
                 '.[] | select((.key | ltrimstr($prefix) | split("-")[0] | tonumber?) < $run) | .id' \

.github/workflows/parity_nightly.yml

@@ -5,9 +5,8 @@
 #             re-sliced on its own to see whether it changes the G-code
 #   harness - the GUI-vs-CLI parity harness (metrics only, never fails)
 # Both test the latest successful build_all.yml Linux AppImage from main, with
-# sources checked out at the commit that build was made from; a manual run can
-# name another branch, or pin one build by its run id. Nothing here gates a
-# build or a PR.
+# sources checked out at the commit that build was made from. Nothing here
+# gates a build or a PR.
 name: Parity Nightly
 
 on:
@@ -21,13 +20,9 @@ on:
         required: false
         default: "main"
       build_branch:
-        description: "branch whose newest successful build_all artifact to test (a PR build is the PR merged into its base; sources are checked out at the PR head)"
+        description: "branch whose latest successful build_all artifact to test"
         required: false
         default: "main"
-      build_run_id:
-        description: "build_all run id to test instead of build_branch's newest (same PR caveat)"
-        required: false
-        default: ""
       fixtures:
         description: "harness fixture ids, space-separated (empty = all)"
         required: false
@@ -55,53 +50,14 @@ jobs:
         env:
           GH_TOKEN: ${{ github.token }}
           GH_REPO: ${{ github.repository }}
-          BRANCH: ${{ inputs.build_branch || 'main' }}
-          RUN_ID: ${{ inputs.build_run_id }}
-          SCHEDULED: ${{ github.event_name == 'schedule' }}
         run: |
           set -euo pipefail
-          if [ -n "$RUN_ID" ]; then
-            [[ $RUN_ID =~ ^[0-9]+$ ]] || { echo "build_run_id must be a numeric run id, got '$RUN_ID'" >&2; exit 1; }
-            # a pinned build is read directly, not through a search; it must come
-            # from this repository, because the later jobs check out its commit here
-            found=$(gh api "repos/$GH_REPO/actions/runs/$RUN_ID" --jq \
-              'select(.path == ".github/workflows/build_all.yml" and .conclusion == "success"
-                      and .head_repository.full_name == env.GH_REPO)
-               | "\(.id) \(.head_sha) \(.created_at)"')
-            [ -n "$found" ] || { echo "run $RUN_ID is not a successful build_all run of $GH_REPO" >&2; exit 1; }
-          else
-            # GitHub serves filtered run listings (branch=, status=, head_sha=, ...)
-            # from a search index that has returned weeks-old results, while the
-            # unfiltered listing stays current, so list unfiltered and filter here.
-            # The repository check keeps out fork PRs whose branch has the same
-            # name. A feature branch is normally built only for its PR, and a PR
-            # build compiles the PR merged into its base rather than head_sha, so
-            # a build of the branch itself (push or dispatch) is preferred when
-            # the same page has one.
-            pick='([.workflow_runs[] | select(.head_branch == env.BRANCH and .conclusion == "success"
-                    and .head_repository.full_name == env.GH_REPO)]
-                   | map(select(.event != "pull_request"))[0] // .[0])
-                  | select(.) | "\(.id) \(.head_sha) \(.created_at)"'
-            # a page of 100 runs spans about a day and a half; a manual run may
-            # target a branch that last built weeks ago
-            pages=3
-            if [ "$SCHEDULED" != true ]; then pages=20; fi
-            found=""
-            for page in $(seq "$pages"); do
-              found=$(gh api "repos/$GH_REPO/actions/workflows/build_all.yml/runs?per_page=100&page=$page" --jq "$pick")
-              if [ -n "$found" ]; then break; fi
-            done
-            [ -n "$found" ] || { echo "no successful $BRANCH build among the last $((pages * 100)) build_all runs; pass build_run_id to test an older one" >&2; exit 1; }
-          fi
-          read -r run_id head_sha created <<< "$found"
-          # the nightly fails rather than report on a stale build
-          if [ "$SCHEDULED" = true ] && [ $(( $(date +%s) - $(date -d "$created" +%s) )) -gt 172800 ]; then
-            echo "newest $BRANCH build $run_id is from $created, over 48 hours old" >&2
-            exit 1
-          fi
-          printf 'run_id=%s\nhead_sha=%s\n' "$run_id" "$head_sha" >> "$GITHUB_OUTPUT"
+          gh run list --workflow build_all.yml \
+            --branch "${{ inputs.build_branch || 'main' }}" \
+            --status success --limit 1 --json databaseId,headSha \
+            --jq '"run_id=\(.[0].databaseId)\nhead_sha=\(.[0].headSha)"' \
+            >> "$GITHUB_OUTPUT"
           cat "$GITHUB_OUTPUT"
-          echo "Testing build [$run_id](https://github.com/$GH_REPO/actions/runs/$run_id) of \`$head_sha\`, built $created" >> "$GITHUB_STEP_SUMMARY"
 
   effect:
     name: Override sweep effect stage (shard ${{ matrix.shard }})

CMakeLists.txt

@@ -1122,6 +1122,7 @@ function(orcaslicer_copy_dlls target config postfix output_dlls)
         ${_out_dir}/swresample-5.dll
         ${_out_dir}/swscale-8.dll
         ${_out_dir}/avutil-59.dll
+        PARENT_SCOPE
     )
     list(APPEND _dll_list ${_occt_staged})
     set(${output_dlls} ${_dll_list} PARENT_SCOPE)

docs/HLSD/deferred-page-construction.md

@@ -1,220 +0,0 @@
-# Deferred Page Construction: High Level Design
-
-## Why it exists
-
-The main window is a notebook of tabs. When the first frame appears, one tab is on
-screen and the others are not; some of them are opened later in the session, some
-never, and some only exist for certain printers. Building a tab before the first frame
-adds its cost to every startup, whether or not the tab is used.
-
-This subsystem builds a tab's panel the first time the tab is shown. It also builds the
-remaining tabs while the user is idle after startup, in units of tens of milliseconds,
-so a click that lands in the middle of one waits for that unit and no longer. Startup
-pays only for what the first frame shows, and the other tabs are usually built before
-anyone opens them.
-
-## The parts
-
-`src/slic3r/GUI/Lazy.hpp`, `LazyPage.hpp`, `StagedBuild.hpp` and `IdleScheduler.hpp/.cpp`
-(with its wx-free `PrebuildQueue.hpp`) are independent. A holder can hold anything a
-factory makes, a page is a holder with a placeholder widget, a staged object can live
-outside a holder, and the scheduler knows none of them; it runs tasks, which `MainFrame`
-makes from the holders.
-
-### Lazy<T>: the holder
-
-Holds an object that a factory makes on first use, under a name for the log and a place
-in the idle queue, both given by the owner. The header has no wx dependency; the busy
-cursor for an on-demand build lives in `Lazy.cpp` and is skipped when there is no app,
-so the holder is unit-tested.
-
-- `get()` is null until the object is completely built; `built()` says the same.
-- `ensure()` builds whatever is left now, under a busy cursor, and returns the object, or
-  null in the two cases below. A click on an unbuilt tab or a first open of a dialog goes
-  through this, and it logs the units and time it took.
-- `build_step()` runs one unit of construction and returns true while more remain. The
-  first unit is the factory call, and each later unit is one `StagedBuild` step if the
-  type has them.
-- `when_built(fn)` runs `fn(object)` now if it exists, otherwise once it is built.
-- `pending()` says whether the idle prebuild has work here: not built, and the factory
-  has not returned null. A null factory result is logged and the holder stays unbuilt.
-- A unit that pumps the event loop cannot re-enter the holder; a nested `build_step()`
-  does nothing and a nested `ensure()` returns null.
-- After a unit throws, the holder and the scheduler still run the next one.
-
-The holder does not own the object; its wx parent does, as for any window. A type with
-one instance in the app derives from `LazyInstance<T>`, which points at that instance's
-holder (the holder registers itself, and a recreated `MainFrame`'s holder replaces the
-old frame's) and gives the type the static entry points the rest of the app uses,
-`T::if_built()`, `T::ensure()` and `T::when_built(fn)`. They return null, or do
-nothing, while no holder exists, so a caller needs no `mainframe` check.
-
-`built()` is an atomic flag, since a job worker reads it through the statics
-(`MainFrame::get_calibration_curr_tab()`); it is set after the object is complete.
-
-`LazyBase` is the holder's type-free interface (`name()`, `built()`, `pending()`,
-`build_step()`, `prebuild_order()`) and is what the scheduler side sees.
-
-### LazyPage<Panel>: the placeholder
-
-A `wxPanel` placed in the parent in place of the real panel, and a `Lazy<Panel>` whose
-factory makes the panel inside it (by default `new Panel(parent)`). The notebook needs a
-page object for the tab to exist and for `show_device()` to insert and remove tabs by
-pointer, and the placeholder is that object. `MainFrame` creates every page once, named
-after its `TAB_ID_*`, and keeps it for the frame's life; `show_device()` only moves
-pages in and out of the book.
-
-- `Show()` is forwarded to the panel, so a panel's own `Show()` override stays its
-  activation hook (refresh timers, machine sync) and `SelectPageByName()` works
-  unchanged. A show builds the panel unless the frame itself is still hidden, because
-  the book selects its first page as it is inserted; `MainFrame::Show()` shows the
-  current page again when the frame becomes visible, which builds it.
-- `in_book()` says whether the parent notebook currently lists the page, and
-  `pending()` is that and not built, so a tab `show_device()` has taken out of the book
-  is not prebuilt.
-- A panel built while its page is hidden stays hidden, and a completed panel gets the
-  dark-mode pass the frame ran before it existed.
-
-The Compare presets dialog is a holder without a page. `MainFrame` keeps a
-`Lazy<DiffPresetDialog>` whose factory constructs the dialog and binds its events, the
-dialog derives from `LazyInstance`, and its callers use
-`DiffPresetDialog::ensure()->show()` and `DiffPresetDialog::if_built()` like a tab's
-callers do. Saving a preset refreshes the dialog only while it is shown, since `show()`
-reloads the presets.
-
-### StagedBuild: construction in units
-
-A mixin for a panel whose constructor is too big to be one unit. The constructor builds
-the skeleton (sizers, and the parts other code may touch) and queues the rest with
-`add_build_step()`. `build_step()` runs one step, and `add_build_steps_of(child)`
-forwards a child's steps so a nested panel is spread the same way; the parent is built
-only once the child is, including steps the child queues later. Steps run in order, on
-the main thread. A `Lazy<T>` recognises a staged type at compile time and runs its steps
-one per unit.
-
-Nothing may touch what a step builds before the last step has run. In practice:
-
-- nothing paints the panel before it is complete, since a panel built at idle is hidden
-  with its page and one built on demand finishes inside `ensure()` before the event loop
-  runs again;
-- members created in steps are initialised to null in the header, so a partially built
-  panel can be destroyed;
-- timers and event handlers that use step content check `built()` first
-  (`MonitorPanel::update_all()`, `CalibrationPanel::update_all()`), and a child's steps
-  are queued before anything in the constructor can fire such a handler;
-- a destructor that disconnects from step content checks `built()` first;
-- a constructor or step does not take focus while the panel is off screen
-  (`IsShownOnScreen()` before `SetFocus()`), since it may run while the user is typing
-  elsewhere;
-- where a step's widgets must keep their place in a sizer that later steps also fill, the
-  constructor adds an empty slot sizer in that position and the step fills the slot
-  (`StatusBasePanel`).
-
-### IdleScheduler: when to build
-
-A task is any `LazyBase`: a name for the log, `pending()`, `build_step()` and
-`prebuild_order()`. `PrebuildQueue` holds the tasks by order (equal order in the order
-added) and runs a slice, the units of the first pending task until it completes, the
-budget is spent on the clock it is given, or the interrupt predicate says input arrived.
-It has no wx dependency and is unit-tested with a fake clock. A task whose work is gone
-is passed over and stays in the queue, so a tab that `show_device()` removes and later
-re-inserts is pending again.
-
-`IdleScheduler` drives the queue with the real clock, the app's input timestamp and the
-Windows queue check, and logs each unit and slice. Each slice is a timer message: a
-period of 250 ms while waiting for the user to go quiet, and a one-shot of zero after a
-slice that left work, so the event loop dispatches whatever it has queued (paint,
-timers, input) before the next slice runs. Chaining slices with `CallAfter` would not do
-this: wx drains pending events fully before the next native message, on every platform.
-On GTK the one-shot is 5 ms, because a due GLib timeout runs ahead of the redraw and
-idle sources that paint and deliver posted events.
-A slice runs only once the user has been idle for the quiet time, and the timer stops
-itself once no task is pending. The tick period, quiet time and slice length are
-constants in `IdleScheduler.cpp`. A unit cannot be interrupted once started, so the
-largest unit bounds click latency on Windows; on the other platforms a click also waits
-for the rest of the slice. A unit that pumps the event loop lets the timer fire inside
-its own slice, and that tick does nothing.
-
-The tasks are made by their owners. `MainFrame::prebuild_pages_when_idle()` registers
-every `LazyPage` the frame created, in or out of the book (`pending()` is false for a
-page out of the book), the Compare presets holder, and the Prepare sidebar's settings
-page from `ParamsPanel::settings_page_prebuild()`, whose first unit selects the default
-tab if none is selected yet and whose later units build one option group each.
-`show_device()` only restarts the timer. `MainFrame` owns the scheduler because it owns
-everything the tasks build, and clearing the queue with the frame is what keeps a task
-from outliving its object.
-
-Idle time comes from `GUI_App::FilterEvent`, which timestamps mouse and keyboard events
-(`wxEVT_CATEGORY_USER_INPUT` minus command events, which all claim that category), and
-`GUI_App::input_idle_ms()` reports it. On Windows a slice additionally refuses to start
-when the message queue holds keyboard, button, touch or pen input. Mouse moves are
-excluded because Windows synthesises one whenever a window appears under the cursor,
-which every unit does. Other platforms use the timestamp alone.
-
-Once every registered page is built the timer is stopped and the subsystem costs
-nothing.
-
-## Rules
-
-**What builds before the first frame.** The Prepare tab's plater, because `post_init()`
-needs its GL canvas on screen to initialise OpenGL in every startup state, and the start
-page the user configured. Home is built by the first `MainFrame::Show()`, Prepare's
-settings page by selecting the tab. `post_init()` passes through the Prepare tab for GL
-init under `Freeze()` with `MainFrame::select_prepare_for_gl_init()`, which changes the
-selection without the page-changed event, so nothing else is built for that pass.
-
-**Reaching a lazy object.** A caller uses the type's own statics. `T::if_built()` may
-return null and is for telling the object something it can live without (a rescale, a
-colour change, a status update). `T::ensure()` builds the object and is for navigating
-to it or for a caller that is about to show it. A caller that tells the object something
-it would not fetch for itself on construction uses `T::when_built()`, which keeps the
-message until the object exists. A panel that pulls its state when constructed (the Home
-page requests the recent list on load, the Device tab reads the device manager on show)
-is reached with `if_built()`; one that cannot pull gets `when_built()`.
-
-**Unit size.** A unit cannot be interrupted, so it should stay within the slice length on
-a fast machine. A constructor above that is staged. A single widget above it is the
-floor unless the widget itself is split.
-
-**Order.** Cheapest and most likely to be opened first, given where `MainFrame` creates
-each holder. The settings page is 0 (the Prepare tab's own content), Home 10, Device 20
-(a Bambu user's usual second stop), Calibration 30, Multi-device 40, the web Device
-view 50, Project 60 (a second WebView2 instance) and the Compare presets dialog 100;
-steps of ten so a new tab takes a value between its neighbours without renumbering
-them. `MainFrame::prebuild_pages_when_idle()` registers the tasks once, from
-`post_init()`.
-
-**Never prebuilt.** A holder with a negative order, for a tab that few sessions open
-and that costs more to build unasked than it saves (the Design tab), and plugin-provided
-tabs, which are Python-side and not lazy pages.
-
-## Adopting it
-
-A lazy tab needs:
-
-1. The panel derived from `LazyInstance<Panel>`, since a tab's panel has one instance.
-2. A `LazyPage<Panel>*` member in `MainFrame`, created once in `init_tabpanel()` with
-   its `TAB_ID_*` as the name, its place by the order rule (and a factory if
-   `new Panel(parent)` is not enough), added to `m_lazy_pages`, and used wherever the
-   tab is added to or looked up in the notebook.
-3. Every use of the panel outside `MainFrame` going through one of the panel's statics,
-   chosen by the rule above. When converting an existing member, `grep` for it; the
-   compiler finds the rest.
-4. A constructor that copes with the frame already existing and the user being busy
-   elsewhere, since `wxGetApp().mainframe` is set, the frame may be shown, and the user
-   may be typing when a lazy panel is built: no `SetFocus()` while off screen, and
-   whatever the constructor did through a `MainFrame` accessor before (a mode update, a
-   deferred URL) done in the constructor itself.
-
-To stage a heavy constructor, inherit `StagedBuild`, keep the skeleton in the constructor,
-move the rest into `add_build_step()` lambdas in the original order, and follow the
-staged-panel rules above. Measure the units. A step that is still one big widget has to
-be split inside that widget or accepted as the floor.
-
-Verification is by log. `MainFrame::prebuild_pages_when_idle` lists the queue it
-registered, `IdleScheduler::tick` reports each completed task by name at info level and
-each slice and unit at debug level, and `Lazy::ensure` reports an object a user built
-on demand with the units and time it took. A run from the configured start
-page shows every registered page complete, in order, with no unit longer than intended.
-A click on a tab mid-prebuild shows the finished panel with an `ensure` line for what was
-left, and the slices resume for the remaining tasks once the user is idle again.

docs/HLSD/preset-cache.md

@@ -76,10 +76,9 @@ and the count of errors the original parse hit.
 
 Each entry is one preset **in source form**: what its JSON sub-file states and nothing
 that resolving it derives — the preset's own config diff, the name of the preset it
-inherits, the names of the presets it includes, and the parse metadata (name, sub-path,
-description, instantiation, setting and filament ids, renames). Non-instantiated base
-presets are stored too; the children that inherit from or include them cannot resolve
-without them.
+inherits, and the parse metadata (name, sub-path, description, instantiation, setting
+and filament ids, renames). Non-instantiated base presets are stored too; the children
+that inherit from them cannot resolve without them.
 
 **The payload names its own keys.** The dictionary holds the distinct `opt_key`s the
 file uses, the `ConfigOptionType` each was written as, and the distinct enum *value
@@ -162,9 +161,9 @@ cache nothing can invalidate is worse than no cache.
 
 Vendors load in a fixed order, because filament inheritance crosses exactly one
 boundary: any vendor's filament may inherit from the shared Orca filament library,
-and nothing else reaches across vendors — an `include` is always vendor-local. The
-library therefore goes first, alone; every other vendor follows in parallel, resolving
-against it; and the results are merged in a stable order:
+and nothing else reaches across vendors. The library therefore goes first, alone;
+every other vendor follows in parallel, resolving against it; and the results are
+merged in a stable order:
 
 ```mermaid
 flowchart LR
@@ -212,16 +211,13 @@ and its cache was never written back.
 
 Serving from a cache is not a memory-image restore. The entries are deserialized and
 then installed one by one — inheritance resolved against the presets installed before
-them and the currently loaded filament library, includes layered in, configs flattened
-onto the collection defaults, validated and registered — by the same function the JSON
-path calls straight after parsing a sub-file. An `include` layers what the included
-base states, between the parent and the preset's own keys: the base's diff against the
-default, taken when the base itself was installed and before the per-variant padding
-`inherits` sees, so only what a template sets reaches the presets including it. The two
-paths share everything below the parse, which is what makes a cache-loaded bundle
-indistinguishable from a JSON-loaded one by construction rather than by test coverage.
-Installation also rebuilds each preset's file path from the local data directory, so a
-shipped cache never carries the generating machine's paths.
+them and the currently loaded filament library, configs flattened onto the collection
+defaults, validated and registered — by the same function the JSON path calls straight
+after parsing a sub-file. The two paths share everything below the parse, which is what
+makes a cache-loaded bundle indistinguishable from a JSON-loaded one by construction
+rather than by test coverage. Installation also rebuilds each preset's file path from
+the local data directory, so a shipped cache never carries the generating machine's
+paths.
 
 App upgrades work because a cache normally survives one. Only a deliberate
 `CACHE_VERSION` bump makes an installed cache unreadable, and that is handled at

localization/i18n/OrcaSlicer.pot

@@ -8,7 +8,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: PACKAGE VERSION\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
 "Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
 "Language-Team: LANGUAGE <LL@li.org>\n"
@@ -6161,6 +6161,9 @@ msgstr ""
 msgid "Preferences"
 msgstr ""
 
+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr ""
@@ -6168,9 +6171,6 @@ msgstr ""
 msgid "View"
 msgstr ""
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr ""
 

localization/i18n/ca/OrcaSlicer_ca.po

@@ -8,7 +8,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-03-15 10:55+0100\n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6637,6 +6637,9 @@ msgstr "Mostrar el contorn al voltant de l'objecte seleccionat a l'escena 3D"
 msgid "Preferences"
 msgstr "Preferències"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6645,9 +6648,6 @@ msgstr "Edita"
 msgid "View"
 msgstr "Vista"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Paquet de perfils"

localization/i18n/cs/OrcaSlicer_cs.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Jakub Hencl\n"
 "Language-Team: \n"
@@ -6602,6 +6602,9 @@ msgstr "Zobrazit obrys kolem vybraného objektu ve 3D scéně."
 msgid "Preferences"
 msgstr "Předvolby"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6610,9 +6613,6 @@ msgstr "Upravit"
 msgid "View"
 msgstr "Zobrazit"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Balík předvoleb"
 

localization/i18n/de/OrcaSlicer_de.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Heiko Liebscher <hliebschergmail.com>\n"
 "Language-Team: \n"
@@ -6490,6 +6490,9 @@ msgstr "Kontur um das ausgewählte Objekt in der 3D-Szene anzeigen."
 msgid "Preferences"
 msgstr "Einstellungen"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6498,9 +6501,6 @@ msgstr "Bearbeiten"
 msgid "View"
 msgstr "Ansicht"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Vorlagen-Bundle"
 

localization/i18n/en/OrcaSlicer_en.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-17 15:44-0300\n"
 "Last-Translator: Alexandre Folle de Menezes\n"
 "Language-Team: \n"
@@ -6157,6 +6157,9 @@ msgstr ""
 msgid "Preferences"
 msgstr ""
 
+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr ""
@@ -6164,9 +6167,6 @@ msgstr ""
 msgid "View"
 msgstr ""
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr ""
 

localization/i18n/es/OrcaSlicer_es.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Ian A. Bassi <>\n"
 "Language-Team: \n"
@@ -6346,6 +6346,9 @@ msgstr "Mostrar el contorno alrededor del objeto seleccionado en la escena 3D."
 msgid "Preferences"
 msgstr "Preferencias"
 
+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Edición"
@@ -6353,9 +6356,6 @@ msgstr "Edición"
 msgid "View"
 msgstr "Vista"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Paquete de perfiles"
 

localization/i18n/eu/OrcaSlicer_eu.po

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-20 13:33+0200\n"
 "Last-Translator: Manu Goiogana <mgoiogana@gmail.com>\n"
 "Language-Team: \n"
@@ -6392,6 +6392,9 @@ msgstr "Erakutsi hautatutako objektuaren inguruko ingerada 3D eszenan."
 msgid "Preferences"
 msgstr "Hobespenak"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6400,9 +6403,6 @@ msgstr "Editatu"
 msgid "View"
 msgstr "Bista"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Aurrezarpen-paketea"
 

localization/i18n/fr/OrcaSlicer_fr.po

@@ -6,7 +6,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: Guislain Cyril, Thomas Lété\n"
@@ -6439,6 +6439,9 @@ msgstr "Afficher le tracé contour de l’objet sélectionné dans la scène 3D.
 msgid "Preferences"
 msgstr "Préférences"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6447,9 +6450,6 @@ msgstr "Édition"
 msgid "View"
 msgstr "Affichage"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Paquet de préréglages"
 

localization/i18n/hu/OrcaSlicer_hu.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "Language: hu\n"
 "MIME-Version: 1.0\n"
 "Content-Type: text/plain; charset=UTF-8\n"
@@ -6541,6 +6541,9 @@ msgstr "Körvonal megjelenítése a kijelölt objektum körül a 3D nézetben."
 msgid "Preferences"
 msgstr "Beállítások"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6549,9 +6552,6 @@ msgstr "Szerkesztés"
 msgid "View"
 msgstr "Nézet"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Beállításcsomag"
 

localization/i18n/it/OrcaSlicer_it.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6543,6 +6543,9 @@ msgstr "Mostra il contorno attorno all'oggetto selezionato nella scena 3D."
 msgid "Preferences"
 msgstr "Preferenze"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6551,9 +6554,6 @@ msgstr "Modifica"
 msgid "View"
 msgstr "Vista"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Pacchetto profili"
 

localization/i18n/ja/OrcaSlicer_ja.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6553,6 +6553,9 @@ msgstr "3Dシーンで選択したオブジェクトの周りにアウトライ
 msgid "Preferences"
 msgstr "設定"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6561,9 +6564,6 @@ msgstr "編集"
 msgid "View"
 msgstr "表示"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "プリセットバンドル"

localization/i18n/ko/OrcaSlicer_ko.po

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-06-02 17:12+0900\n"
 "Last-Translator: crwusiz <crwusiz@gmail.com>\n"
 "Language-Team: \n"
@@ -6566,6 +6566,9 @@ msgstr "3D 장면에서 선택한 객체 주변에 윤곽선 표시"
 msgid "Preferences"
 msgstr "기본 설정"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6574,9 +6577,6 @@ msgstr "편집"
 msgid "View"
 msgstr "시점"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "사전 설정 번들"

localization/i18n/lt/OrcaSlicer_lt.po

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-02 14:13+0300\n"
 "Last-Translator: Gintaras Kučinskas <sharanchius@gmail.com>\n"
 "Language-Team: \n"
@@ -6528,6 +6528,9 @@ msgstr "Rodyti kontūrą aplink pasirinktą objektą 3D scenoje."
 msgid "Preferences"
 msgstr "Parinktys"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6536,9 +6539,6 @@ msgstr "Redaguoti"
 msgid "View"
 msgstr "Vaizdas"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Profilių rinkinys"
 

localization/i18n/nl/OrcaSlicer_nl.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -7122,6 +7122,9 @@ msgstr "Toon een omtrek rond het geselecteerde object in de 3D-scène."
 msgid "Preferences"
 msgstr "Voorkeuren"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -7130,9 +7133,6 @@ msgstr "Bewerken"
 msgid "View"
 msgstr "Weergave"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Voorinstellingenbundel"

localization/i18n/pl/OrcaSlicer_pl.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: OrcaSlicer 2.3.0-rc\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Krzysztof Morga <<tlumaczeniebs@gmail.com>>\n"
 "Language-Team: \n"
@@ -6689,6 +6689,9 @@ msgstr "Przełącza wyświetlanie konturu wokół zaznaczonego obiektu w scenie
 msgid "Preferences"
 msgstr "Preferencje"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6697,9 +6700,6 @@ msgstr "Edycja"
 msgid "View"
 msgstr "Widok"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Pakiet profili"

localization/i18n/pt_BR/OrcaSlicer_pt_BR.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-26 11:14-0300\n"
 "Last-Translator: Alexandre Folle de Menezes\n"
 "Language-Team: Portuguese, Brazilian\n"
@@ -6363,6 +6363,9 @@ msgstr "Mostrar contorno ao redor do objeto selecionado na cena 3D."
 msgid "Preferences"
 msgstr "Preferências"
 
+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Editar"
@@ -6370,9 +6373,6 @@ msgstr "Editar"
 msgid "View"
 msgstr "Visualizar"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Pacote de Predefinições"
 

localization/i18n/ru/OrcaSlicer_ru.po

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: OrcaSlicer V2.5.0\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-02-25 13:38+0300\n"
 "Last-Translator: Felix14_v2\n"
 "Language-Team: Felix14_v2 (ДС/ТГ: @felix14_v2, почта: aleks111001@list.ru), Andylg <andylg@yandex.ru>\n"
@@ -6597,6 +6597,9 @@ msgstr "Отображение контура вокруг выбранных м
 msgid "Preferences"
 msgstr "Настройки"
 
+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Правка"
@@ -6604,9 +6607,6 @@ msgstr "Правка"
 msgid "View"
 msgstr "Вид"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Пакет профилей"
 

localization/i18n/sv/OrcaSlicer_sv.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "Language: sv\n"
 "MIME-Version: 1.0\n"
 "Content-Type: text/plain; charset=UTF-8\n"
@@ -7205,6 +7205,9 @@ msgstr "Visa en kontur runt det markerade objektet i 3D-scenen."
 msgid "Preferences"
 msgstr "Inställningar"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -7213,9 +7216,6 @@ msgstr "Redigera"
 msgid "View"
 msgstr "Vy"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Förinställningspaket"

localization/i18n/th/OrcaSlicer_th.po

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-19 13:40+0700\n"
 "Last-Translator: Icezaza\n"
 "Language-Team: Thai\n"
@@ -6520,6 +6520,9 @@ msgstr "แสดงเค้าร่างรอบๆ วัตถุที
 msgid "Preferences"
 msgstr "การตั้งค่า"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6528,9 +6531,6 @@ msgstr "แก้ไข"
 msgid "View"
 msgstr "มุมมอง"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "ชุดที่ตั้งไว้ล่วงหน้า"
 

localization/i18n/tr/OrcaSlicer_tr.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-08-21 23:18+0300\n"
 "Last-Translator: GlauTech\n"
 "Language-Team: \n"
@@ -6588,6 +6588,9 @@ msgstr "3D sahnede seçilen nesnenin etrafındaki ana hatları göster."
 msgid "Preferences"
 msgstr "Tercihler"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6596,9 +6599,6 @@ msgstr "Düzen"
 msgid "View"
 msgstr "Görünüm"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Ön ayar paketi"
 

localization/i18n/uk/OrcaSlicer_uk.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: orcaslicerua\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-17 16:25+0300\n"
 "Last-Translator: Andrij Mizyk <andm1zyk@proton.me>\n"
 "Language-Team: Ukrainian\n"
@@ -6557,6 +6557,9 @@ msgstr "Показувати контур навколо виділеного о
 msgid "Preferences"
 msgstr "Налаштування"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6565,9 +6568,6 @@ msgstr "Редагування"
 msgid "View"
 msgstr "Вигляд"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Набір пресетів"
 

localization/i18n/vi/OrcaSlicer_vi.po

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-10-02 17:43+0700\n"
 "Last-Translator: \n"
 "Language-Team: hainguyen.ts13@gmail.com\n"
@@ -6907,6 +6907,9 @@ msgstr "Hiện đường viền xung quanh vật thể đã chọn trong cảnh
 msgid "Preferences"
 msgstr "Tùy chọn"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6915,9 +6918,6 @@ msgstr "Chỉnh sửa"
 msgid "View"
 msgstr "Xem"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Gói cài đặt sẵn"

localization/i18n/zh_CN/OrcaSlicer_zh_CN.po

@@ -6,7 +6,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Slic3rPE\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-11 12:37-0300\n"
 "Last-Translator: Handle <mail@bysb.net>\n"
 "Language-Team: \n"
@@ -6375,6 +6375,9 @@ msgstr "在3D场景中显示选中对象的轮廓"
 msgid "Preferences"
 msgstr "偏好设置"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6383,9 +6386,6 @@ msgstr "编辑"
 msgid "View"
 msgstr "视图"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "预设包"
 

localization/i18n/zh_TW/OrcaSlicer_zh_TW.po

@@ -9,7 +9,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-11-28 13:48-0600\n"
 "Last-Translator: tntchn <15895303+tntchn@users.noreply.github.com>\n"
 "Language-Team: \n"
@@ -6505,6 +6505,9 @@ msgstr "在 3D 場景中顯示選定物件的輪廓"
 msgid "Preferences"
 msgstr "偏好設定"
 
+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6513,9 +6516,6 @@ msgstr "編輯"
 msgid "View"
 msgstr "視角"
 
-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "設定檔組"
 

resources/profiles/Anker/machine/fdm_marlin_common.json

@@ -6,7 +6,6 @@
 	"instantiation": "false",
 	"gcode_flavor": "marlin2",
 	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n",
-	"file_start_gcode": ";TIME:{print_time_sec}s",
 	"machine_start_gcode": "M4899 T3 ; Enable v3 jerk and S-curve acceleration \nM104 S150 ; Set hotend temp to 150 degrees to prevent ooze\nM190 S{first_layer_bed_temperature[0]} ; set and wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; set final nozzle temp to stabilize\nG28 ;Home\n;LAYER_COUNT:{total_layer_count}",
 	"machine_end_gcode": "M104 S0\nM140 S0\n;Retract the filament\nG92 E1\nG1 E-1 F300\nG28 X0 Y0\nM18",
 	"change_filament_gcode": "M600",

resources/profiles/Anycubic.json

@@ -1,6 +1,6 @@
 {
 	"name": "Anycubic",
-	"version": "02.04.00.07",
+	"version": "02.04.00.05",
 	"force_update": "0",
 	"description": "Anycubic configurations",
 	"machine_model_list": [
@@ -48,10 +48,6 @@
 			"name": "Anycubic Kobra 3 Max",
 			"sub_path": "machine/Anycubic Kobra 3 Max.json"
 		},
-		{
-			"name": "Anycubic Kobra 3 V2",
-			"sub_path": "machine/Anycubic Kobra 3 V2.json"
-		},
 		{
 			"name": "Anycubic Kobra Max",
 			"sub_path": "machine/Anycubic Kobra Max.json"
@@ -106,10 +102,6 @@
 			"name": "0.08mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.08mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.08mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.08mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -126,10 +118,6 @@
 			"name": "0.10mm Detail @Anycubic Kobra 3 0.2 nozzle",
 			"sub_path": "process/0.10mm Detail @Anycubic Kobra 3 0.2 nozzle.json"
 		},
-		{
-			"name": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "process/0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
 		{
 			"name": "0.10mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.10mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -154,10 +142,6 @@
 			"name": "0.12mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.12mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.12mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.12mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -230,10 +214,6 @@
 			"name": "0.16mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.16mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.16mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.16mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -306,10 +286,6 @@
 			"name": "0.20mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.20mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.20mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.20mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -366,10 +342,6 @@
 			"name": "0.24mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.24mm Standard @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "process/0.24mm Standard @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -398,10 +370,6 @@
 			"name": "0.28mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.28mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.28mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.28mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -458,10 +426,6 @@
 			"name": "0.30mm Standard @Anycubic Kobra 3 Max 0.6 nozzle",
 			"sub_path": "process/0.30mm Standard @Anycubic Kobra 3 Max 0.6 nozzle.json"
 		},
-		{
-			"name": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
 		{
 			"name": "0.30mm Standard @Anycubic Kobra S1 Max 0.6 nozzle",
 			"sub_path": "process/0.30mm Standard @Anycubic Kobra S1 Max 0.6 nozzle.json"
@@ -490,10 +454,6 @@
 			"name": "0.40mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.40mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "0.40mm Standard @Anycubic Kobra S1 Max 0.8 nozzle",
 			"sub_path": "process/0.40mm Standard @Anycubic Kobra S1 Max 0.8 nozzle.json"
@@ -517,34 +477,6 @@
 		{
 			"name": "0.56mm Standard @Anycubic Kobra S1 Max 0.8 nozzle",
 			"sub_path": "process/0.56mm Standard @Anycubic Kobra S1 Max 0.8 nozzle.json"
-		},
-		{
-			"name": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
 		}
 	],
 	"filament_list": [
@@ -596,10 +528,6 @@
 			"name": "Anycubic ABS @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic ABS @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic ABS @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic ABS @Anycubic Kobra S1 0.4 nozzle.json"
@@ -636,10 +564,6 @@
 			"name": "Anycubic ASA @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic ASA @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic ASA @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic ASA @Anycubic Kobra S1 0.4 nozzle.json"
@@ -780,10 +704,6 @@
 			"name": "Anycubic PETG @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PETG @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra S1 0.4 nozzle.json"
@@ -848,22 +768,6 @@
 			"name": "Anycubic PLA @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra S1 0.4 nozzle.json"
@@ -888,22 +792,6 @@
 			"name": "Anycubic PLA @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Glow @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Glow @Anycubic Kobra X 0.4 nozzle.json"
@@ -912,10 +800,6 @@
 			"name": "Anycubic PLA High Speed @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA High Speed @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra S1 0.4 nozzle.json"
@@ -940,26 +824,10 @@
 			"name": "Anycubic PLA Luminous @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Luminous @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Matte @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Matte @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -976,30 +844,10 @@
 			"name": "Anycubic PLA Matte @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Silk @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Silk @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra S1 0.4 nozzle.json"
@@ -1020,10 +868,6 @@
 			"name": "Anycubic PLA Silk @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Translucent @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Translucent @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -1136,10 +980,6 @@
 			"name": "Anycubic TPU @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic TPU @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic TPU @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic TPU @Anycubic Kobra S1 0.4 nozzle.json"
@@ -1176,22 +1016,6 @@
 			"name": "Anycubic PETG @Anycubic Kobra 3 0.4 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA @Anycubic Kobra 2 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 2 Max 0.4 nozzle.json"
@@ -1350,22 +1174,6 @@
 			"name": "Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "machine/Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic Kobra Max 0.4 nozzle",
 			"sub_path": "machine/Anycubic Kobra Max 0.4 nozzle.json"

resources/profiles/Anycubic/filament/Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_abs",
-	"from": "system",
-	"setting_id": "LXkKhWH9YcYPr3IT",
-	"filament_id": "OF223rZv",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"ABS"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"5"
-	],
-	"nozzle_temperature": [
-		"250"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"15"
-	],
-	"fan_min_speed": [
-		"1"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.05"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"70%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"100"
-	],
-	"hot_plate_temp": [
-		"90"
-	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
-	"nozzle_temperature_initial_layer": [
-		"250"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"15"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"16"
-	],
-	"slow_down_min_speed": [
-		"25"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"90"
-	],
-	"textured_plate_temp_initial_layer": [
-		"90"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_asa",
-	"from": "system",
-	"setting_id": "cWBQa7XzDl3czIOs",
-	"filament_id": "OF0yFLkY",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"ASA"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"270"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"15"
-	],
-	"fan_min_speed": [
-		"1"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"30"
-	],
-	"filament_density": [
-		"1.04"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"70%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"100"
-	],
-	"hot_plate_temp": [
-		"100"
-	],
-	"hot_plate_temp_initial_layer": [
-		"100"
-	],
-	"nozzle_temperature_initial_layer": [
-		"270"
-	],
-	"nozzle_temperature_range_high": [
-		"280"
-	],
-	"nozzle_temperature_range_low": [
-		"240"
-	],
-	"overhang_fan_speed": [
-		"15"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"16"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"110"
-	],
-	"textured_plate_temp": [
-		"100"
-	],
-	"textured_plate_temp_initial_layer": [
-		"100"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pet",
-	"from": "system",
-	"setting_id": "suyxKj9qKLtpBhhU",
-	"filament_id": "OFo6n2pB",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PETG"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"8"
-	],
-	"nozzle_temperature": [
-		"230"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"15"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.23"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"80%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"6"
-	],
-	"hot_plate_temp": [
-		"70"
-	],
-	"hot_plate_temp_initial_layer": [
-		"70"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"90"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"25"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"70"
-	],
-	"textured_plate_temp_initial_layer": [
-		"70"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,42 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "OOOjWFMFhP1fMhFf",
-	"filament_id": "OFo6n2pB",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PETG"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"hot_plate_temp": [
-		"70"
-	],
-	"hot_plate_temp_initial_layer": [
-		"70"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "uJRZr6orTVm79FeE",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"1.6"
-	],
-	"nozzle_temperature": [
-		"230"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "udLvkeYZ9Av7GkDz",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "W69H1Vca3f74FfYj",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "TR27JCwXxHeVhVHN",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.6"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "i0FTxiH68CKHiLLT",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,258 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "XHa1HSjh0RjAo0nz",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_layer_time_BRASS": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,261 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "iRVPFxNMEfkCDnMh",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_max_speed_BRASS": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"fan_min_speed_BRASS": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "itTckVFabfsVbNBK",
-	"filament_id": "OF5PtjTp",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"0"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"40"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"0%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"2"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"2"
-	],
-	"filament_z_hop": [
-		"0.4"
-	],
-	"filament_z_hop_types": [
-		"Auto Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"9"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "YLxoiuRDXBWLQYw4",
-	"filament_id": "OFjVOWfJ",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"18"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"2"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"210"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"7"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "JwcCfY4XVCRJaDeS",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "Sjw7irNgwCZMfWS3",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"50"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "HeQwxU4T2W1V0LM3",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"210"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "H3PIqeTzjvtFQXYv",
-	"filament_id": "OFIE3vOf",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"9"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"0"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "4zmGMIi6jHJhU4c6",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.97"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "wLkJ1CJgdWnT4NoJ",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"50"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "kkcDxmDe6F9fwhoJ",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "QRl3zpmacQ8D8aNX",
-	"filament_id": "OFCp3Bgo",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.97"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"14"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "qF5SGZKoINokZfx2",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,51 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "6aUrszW2Dj8CNYIp",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"pressure_advance": [
-		"0.025"
-	],
-	"slow_down_layer_time": [
-		"10"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,51 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "f8K19ebfxiXji84y",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"pressure_advance": [
-		"0.025"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,273 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "NTs7c6NqAudTl9wk",
-	"filament_id": "OF7c9fln",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"dont_slow_down_outer_wall": [
-		"1"
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_cooling_layer_time_BRASS": [
-		"100"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_max_speed_BRASS": [
-		"100"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"fan_min_speed_BRASS": [
-		"70"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_BRASS": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"0"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_layer_time_BRASS": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/filament/Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_tpu",
-	"from": "system",
-	"setting_id": "oSWtTJpng3ERixPJ",
-	"filament_id": "OFMsDGbs",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"TPU"
-	],
-	"filament_flow_ratio": [
-		"1"
-	],
-	"filament_max_volumetric_speed": [
-		"3.2"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.23"
-	],
-	"filament_deretraction_speed": [
-		"25"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"0%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"35"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"95%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}

resources/profiles/Anycubic/machine/Anycubic Kobra 3 V2 0.2 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "gaQ37xRo6J467j1y",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.2 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.2",
-	"nozzle_diameter": [
-		"0.2"
-	],
-	"default_print_profile": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": [
-		"230x110"
-	],
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": [
-		"512x512/PNG/top"
-	],
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"40"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "G92 E0\nG1 E-2 F3600\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F900 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.14"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0.3"
-	],
-	"retract_lift_below": [
-		"258"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"0"
-	],
-	"retraction_speed": [
-		"40"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"1"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}

resources/profiles/Anycubic/machine/Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,251 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "l49qdfdrHYEO04bV",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.4 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.4",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"default_print_profile": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": "230x110/PNG",
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": "512x512/PNG/top",
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"60"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400\nG92 E0 ; zero the extruder\nG1 E-2 F3600\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F900 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.28"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"259"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"1"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"60"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "0",
-	"support_chamber_temp_control": "0",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Slope Lift"
-	],
-	"z_offset": "0"
-}

resources/profiles/Anycubic/machine/Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,251 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "hQQgQT5HeCVGpBAL",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.6 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.6",
-	"nozzle_diameter": [
-		"0.6"
-	],
-	"default_print_profile": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": "230x110/PNG",
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": "512x512/PNG/top",
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"30"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400 ; wait for buffer to clear\nG92 E0 ; zero the extruder\nG1 E-1 F3600 ; retract\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F600 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.05\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.42"
-	],
-	"min_layer_height": [
-		"0.12"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"259"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"30"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}

resources/profiles/Anycubic/machine/Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,255 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "LBhbohm7o4jW6OYw",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.8 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.8",
-	"nozzle_diameter": [
-		"0.8"
-	],
-	"default_print_profile": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": [
-		"230x110"
-	],
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": [
-		"512x512/PNG/top"
-	],
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"0"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400 ; wait for buffer to clear\nG92 E0 ; zero the extruder\nG1 E-2 F3000 ; retract\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F600 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.56"
-	],
-	"min_layer_height": [
-		"0.16"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0.3"
-	],
-	"retract_lift_below": [
-		"259.6"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"1"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"40"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}

resources/profiles/Anycubic/machine/Anycubic Kobra 3 V2.json

@@ -1,12 +0,0 @@
-{
-    "type": "machine_model",
-    "machine_tech": "FFF",
-    "family": "Anycubic",
-    "name": "Anycubic Kobra 3 V2",
-    "model_id": "Anycubic Kobra 3 V2",
-    "nozzle_diameter": "0.4;0.2;0.6;0.8",
-    "bed_model": "Anycubic Kobra 3 V2_buildplate_model.stl",
-    "bed_texture": "Anycubic Kobra 3 V2_buildplate_texture.svg",
-    "hotend_model": "",
-    "default_materials": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-}

resources/profiles/Anycubic/process/0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "9yiDozcVDSxKkz4V",
-	"instantiation": "true",
-	"print_settings_id": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.08",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "7",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "1",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "350",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "8%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "3",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "200",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "1",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "grid",
-	"sparse_infill_speed": "450",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.08",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "15",
-	"support_top_z_distance": "0.08",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "9",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "200",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "eSyZsnWMuOyokoLr",
-	"instantiation": "true",
-	"print_settings_id": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"layer_height": "0.1",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "5",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "50%",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "10",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.075",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "0",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "100",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.25",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.1",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "10",
-	"inner_wall_line_width": "0.22",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "100%",
-	"internal_solid_infill_line_width": "0.22",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "120",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.22",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "10",
-	"outer_wall_line_width": "0.22",
-	"outer_wall_speed": "80",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "100%",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "20",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "100%",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.22",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "150",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.1",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.5",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.22",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.1",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "7",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.22",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "120",
-	"travel_acceleration": "15000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "4",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,58 +0,0 @@
-{
-	"type": "process",
-	"name": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "HqXRokM0mAA691LV",
-	"instantiation": "true",
-	"print_settings_id": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.12",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "2000",
-	"bridge_speed": "30",
-	"brim_type": "auto_brim",
-	"default_acceleration": "5000",
-	"default_jerk": "9",
-	"gap_infill_speed": "180",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"inner_wall_speed": "150",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_speed": "180",
-	"ironing_flow": "10%",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "60",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "35",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"small_perimeter_speed": "50%",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_speed": "180",
-	"support_interface_top_layers": "2",
-	"support_threshold_angle": "20",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_speed": "150",
-	"travel_acceleration": "5000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}

resources/profiles/Anycubic/process/0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "NCKx6glFcaEOhqZC",
-	"instantiation": "true",
-	"print_settings_id": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.12",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "5",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "350",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "300",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "430",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.12",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "20",
-	"support_top_z_distance": "0.12",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "5",
-	"top_shell_thickness": "0.6",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "200",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,51 +0,0 @@
-{
-	"type": "process",
-	"name": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "mVDCX89vYKfBA57g",
-	"instantiation": "true",
-	"print_settings_id": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.16",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "2000",
-	"default_acceleration": "4000",
-	"default_jerk": "9",
-	"infill_anchor_max": "20",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"internal_solid_infill_acceleration": "4000",
-	"internal_solid_infill_speed": "200",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "150",
-	"overhang_1_4_speed": "60",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "30",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"small_perimeter_speed": "50%",
-	"sparse_infill_acceleration": "4000",
-	"sparse_infill_speed": "200",
-	"support_line_width": "0.42",
-	"support_threshold_angle": "25",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "4000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}

resources/profiles/Anycubic/process/0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "ut3FZjM7h3doFjRg",
-	"instantiation": "true",
-	"print_settings_id": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.16",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "4",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "300",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.16",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "25",
-	"support_top_z_distance": "0.16",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "6",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "150",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,57 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "V7T6yBxuQzWucCpA",
-	"instantiation": "true",
-	"print_settings_id": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.2",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "4000",
-	"bridge_speed": "50",
-	"brim_object_gap": "0.1",
-	"brim_width": "5",
-	"default_acceleration": "4000",
-	"default_jerk": "9",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"inner_wall_speed": "150",
-	"internal_solid_infill_acceleration": "4000",
-	"internal_solid_infill_speed": "250",
-	"ironing_flow": "10%",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "60",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "30",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"sparse_infill_acceleration": "4000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "270",
-	"support_line_width": "0.42",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_speed": "200",
-	"travel_acceleration": "4000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}

resources/profiles/Anycubic/process/0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "K5se4jnf2XHJNkEQ",
-	"instantiation": "true",
-	"print_settings_id": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.2",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "130",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "300",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.4",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "30",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "0",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "5",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "130",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "cg8f6Q9o8nRePSC9",
-	"instantiation": "true",
-	"print_settings_id": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.24",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "200",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.45",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "200",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "35",
-	"support_top_z_distance": "0.2",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "4",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "180",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,24 +0,0 @@
-{
-	"type": "process",
-	"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "DhqKrBJZh4W22xna",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.24",
-	"brim_type": "auto_brim",
-	"default_acceleration": "6000",
-	"default_jerk": "9",
-	"elefant_foot_compensation": "0.1",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"outer_wall_jerk": "9",
-	"raft_first_layer_expansion": "5",
-	"sparse_infill_acceleration": "6000",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9"
-}

resources/profiles/Anycubic/process/0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "Qe8XQonRxfA8Jei1",
-	"instantiation": "true",
-	"print_settings_id": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.28",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "2000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "200",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "180",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "0%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "grid",
-	"sparse_infill_speed": "200",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.2",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "4",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "180",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "13ES5eks7VTR3G2E",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.3",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "500",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "5000",
-	"default_jerk": "20",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.075",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "50",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.62",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.3",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "10000",
-	"inner_wall_jerk": "15",
-	"inner_wall_line_width": "0.62",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.62",
-	"internal_solid_infill_pattern": "monotonic",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.62",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "0",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "15",
-	"outer_wall_line_width": "0.62",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "15",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "35",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "1",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.62",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "100",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.62",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "3",
-	"top_shell_thickness": "0.6",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "5000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.62",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "150",
-	"travel_acceleration": "15000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "150%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,17 +0,0 @@
-{
-	"type": "process",
-	"name": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "avPzsOBN3DnXTaol",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.32",
-	"initial_layer_print_height": "0.32",
-	"inner_wall_speed": "120",
-	"outer_wall_speed": "80",
-	"overhang_2_4_speed": "40",
-	"overhang_3_4_speed": "30",
-	"top_solid_infill_flow_ratio": "0.95"
-}

resources/profiles/Anycubic/process/0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json

@@ -1,24 +0,0 @@
-{
-	"type": "process",
-	"name": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "7pIVSig189FDjOMY",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.36",
-	"brim_type": "auto_brim",
-	"default_acceleration": "6000",
-	"default_jerk": "9",
-	"elefant_foot_compensation": "0.1",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"outer_wall_jerk": "9",
-	"raft_first_layer_expansion": "5",
-	"sparse_infill_acceleration": "6000",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9"
-}

resources/profiles/Anycubic/process/0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "0yxg7c5tH07ZMIL4",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.4",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "6000",
-	"default_jerk": "20",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "1",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "50",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.82",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.4",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "0",
-	"inner_wall_jerk": "15",
-	"inner_wall_line_width": "0.82",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.82",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.82",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "0",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "15",
-	"outer_wall_line_width": "0.82",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "25",
-	"overhang_4_4_speed": "5",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "100%",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "20",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.82",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "100",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.82",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "3",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.82",
-	"top_surface_pattern": "monotonic",
-	"top_surface_speed": "150",
-	"travel_acceleration": "10000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "1.5",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "150%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}

resources/profiles/Anycubic/process/0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json

@@ -1,17 +0,0 @@
-{
-	"type": "process",
-	"name": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "2cCCPfRX7H33XrMb",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.48",
-	"initial_layer_print_height": "0.48",
-	"inner_wall_speed": "180",
-	"outer_wall_speed": "140",
-	"overhang_2_4_speed": "40",
-	"overhang_3_4_speed": "30",
-	"top_solid_infill_flow_ratio": "0.95"
-}