Keep the Scarf Seam Free of Sub-Millimetre Segments

A scarf joint split the loop at exactly the scarf length, so the remainder of the segment the split landed in became the first flat segment, often a fraction of a millimetre. The seam insertion also leaves segments of a few micrometres at both ends of the loop, which a scarf extrudes through where a plain loop would start or stop. With junction deviation the planner treats such short moves as tight corners, limited by the Z axis acceleration at the end of the ramp, and slows to a third of the wall speed or nearly halts at the seam. Extend the ramp to the next vertex when the remainder would be shorter than half a scarf step, capped at a millimetre, beyond which planners treat a move as ordinary; the scarf only grows, never shrinks. Drop the vertex next to the seam point at either end when that segment is shorter than an eighth of a common line width, so the loop still starts and ends at the seam; a trimmed path loses its arc fitting and prints as line segments. Clamp the scarf length to the trimmed loop so a scarf covering a whole loop still ends at full flow. The descending pass reuses the same path, so both wedges stay consistent, and a flat part that would collapse to a single point is dropped.
2026-09-29 03:41:31 +00:00 · 2026-09-23 01:48:53 +08:00
4184 changed files with 275776 additions and 250076 deletions
@@ -35,10 +35,9 @@ toolhead, a multi-material build) may drop the suffix — still an exact referen
 ## `process`

 `<layer height>mm <quality> @<target>` — [process-profiles.md](process-profiles.md#naming) has the
-quality ladder and the `fdm_process_*` base names. The quality label stays before `@` and the printer
-target after it: a printer model in the quality slot leaves the tier undescribed. The `@<target>` is a
-human label, not a reference: it usually does not equal a real variant, and compatibility comes from the
-resolved `compatible_printers` list or condition.
+quality ladder and the `fdm_process_*` base names. The `@<target>` is a human label, not a reference: it
+usually does not equal a real variant, and compatibility comes from the resolved `compatible_printers`
+list or condition.

 ## `filament`

@@ -59,30 +58,6 @@ to the first `@`; the target half is a label except for reserved forms:
  chosen at runtime
  ([color is a runtime property](filament-profiles.md#color-is-a-runtime-property)).

-## Checking names
-
-Check every newly added profile's `name` against its type and role: model, selectable preset or base.
-Apply the same checks to an intentional name change. The human-readable naming shapes are not enforced
-by `check`: inspect the added or renamed profiles in the diff, using neighbouring names as context and
-following the bundle's established style where the type-specific conventions allow variation.
-
-For bases (`instantiation: "false"`), use the type-specific conventions:
-
-| Type | Base names |
-| --- | --- |
-| `machine` | `fdm_machine_common`, `fdm_<vendor>_common`, or an established machine-family base name |
-| `process` | `fdm_process_*`, including shared roots and per-layer-height / per-nozzle bases such as `fdm_process_single_0.20` |
-| `filament` | `fdm_filament_*` material roots or `<Product> @base` product roots |
-
-Shared base names across bundles are intentional, including product roots such as `Fiberon PA6-CF @base`.
-Investigate a newly authored base that retains an unrelated selectable preset's name from a copy.
-
-**Name uniqueness is checked by CI.** `check_preset_name_uniqueness` checks type + name within each
-bundle. `check_machine_model_name_uniqueness` checks model names across the entire tree, even with
-`--vendor`: `Preset::get_printer_type` matches `printer_model` against all vendors' models and returns
-the first match, so a duplicate makes lookup depend on vendor order. Both run as part of
-`python3 scripts/orca_profile_tool.py check`.
-
 ## Not the same as the filename

 The loader keys off `name`, and a filename that disagrees usually still loads. Index `name` must equal the
@@ -17,7 +17,6 @@ The table highlights gaps that need human review. What CI *does* run:
 | A `renamed_from` whose old name is still a live preset | The redirect is inert while a live preset carries that name |
 | A preset differentiated only by color, or an all-printer library preset without `@System` | Per-color presets split one product across ids and the selector fills with near-duplicates; CI stays green |
 | Per-extruder vector length on a multi-nozzle printer | Silently padded (with the **first** value) or truncated |
-| A name that ignores its type's convention — a model in a `process` quality slot, or an unrelated target label left in a copied preset | The selector misrepresents the preset's quality or intended printer |

 ## 1. Was the vendor `version` bumped?

@@ -170,15 +169,6 @@ vendor, and a filename that disagrees with the preset's `name` (common; the load
 Check for Windows-invalid characters, reserved device names, trailing path-component spaces/dots,
 and case mismatches in `sub_path` or asset paths. See [cross-platform paths](validation.md#cross-platform-paths).

-## 16. Do the preset names follow the conventions?
-
-Check **every newly added profile and intentional name change**, including models and bases,
-against [the naming conventions](naming.md#checking-names). Preserve shipped names during
-ordinary tuning; renaming a shipped selectable preset requires the migration in item 4.
-
-*Why:* CI checks name uniqueness, but does not enforce the naming conventions. Catch naming
-mistakes before the names ship and existing projects depend on them.
-
 ---

 ## Reporting the review
@@ -413,14 +413,6 @@ jobs:
        GH_TOKEN: ${{ github.token }}
      run: |
        api="$GITHUB_API_URL/repos/$GITHUB_REPOSITORY/actions/caches"
-        # The save step reports success even when its tar failed, so keep
-        # the older entries unless the new one is listed.
-        if ! curl -sSf -H "Authorization: Bearer $GH_TOKEN" \
-            "$api?ref=$GITHUB_REF&key=$CCACHE_ENTRY" \
-            | jq -e --arg entry "$CCACHE_ENTRY" 'any(.actions_caches[]; .key == $entry)' > /dev/null; then
-          echo "$CCACHE_ENTRY was not saved; keeping the older entries."
-          exit 0
-        fi
        curl -sSf -H "Authorization: Bearer $GH_TOKEN" \
          "$api?ref=$GITHUB_REF&key=ccache-$CCACHE_LEG-&per_page=100" \
          | jq -r --arg prefix "ccache-$CCACHE_LEG-" --argjson run "$GITHUB_RUN_ID" \
@@ -798,13 +798,6 @@ jobs:
        env:
          GH_TOKEN: ${{ github.token }}
        run: |
-          # The save step reports success even when its tar failed, so keep
-          # the older entries unless the new one is listed.
-          if ! gh cache list --ref "$GITHUB_REF" --key "$CCACHE_ENTRY" --json key \
-              | jq -e --arg entry "$CCACHE_ENTRY" 'any(.[]; .key == $entry)' > /dev/null; then
-            echo "$CCACHE_ENTRY was not saved; keeping the older entries."
-            exit 0
-          fi
          gh cache list --ref "$GITHUB_REF" --key "ccache-$CCACHE_LEG-" --limit 100 --json id,key \
            | jq -r --arg prefix "ccache-$CCACHE_LEG-" --argjson run "$GITHUB_RUN_ID" \
                '.[] | select((.key | ltrimstr($prefix) | split("-")[0] | tonumber?) < $run) | .id' \
@@ -1,199 +0,0 @@
-name: Daily OFL OTA Update
-
-run-name: Daily OFL OTA Update [OFL barrier]
-
-# This workflow is intended for creating and publishing the OrcaFilamentLibrary (OFL) OPC package to
-# https://github.com/OrcaSlicer/orcaslicer-profiles, which generates an OTA update.
-# This cronjob runs daily at 00:00 UTC every day and scans main plus every release/vX.Y.Z branch for
-# changes to resources/profiles/OrcaFilamentLibrary since that branch's own last successful run. Any
-# branch with no changes is skipped; each changed branch gets its own post_merge_profiles.yml dispatch.
-#
-# OFL has no dedicated FOLDER_MERGERS grant (it isn't merged through the PR merge-bot delegation
-# scheme), so post_merge_profiles.yml is dispatched with an explicit `vendor` input, which that
-# workflow trusts and uses to bypass the FOLDER_MERGERS check for this trigger. That same explicit-
-# vendor-dispatch path is also what makes post_merge_profiles.yml call the OTA auto-publish API after
-# uploading - see post_merge_profiles.yml for both sides of that contract.
-#
-# Each run captures a timestamp, dispatches the needed OFL publishers, waits for
-# all of them to finish, then clears the pending-publish table once. Changes merged
-# after that timestamp remain pending for the next run.
-
-on:
-  schedule:
-    - cron: "0 0 * * *"
-
-  workflow_dispatch:
-
-permissions:
-  actions: write # list this workflow's past runs and dispatch post_merge_profiles.yml
-  contents: read
-
-env:
-  VENDOR: OrcaFilamentLibrary
-
-jobs:
-  daily-job:
-    if: ${{ github.repository == 'OrcaSlicer/OrcaSlicer' }}
-    runs-on: ubuntu-24.04
-    steps:
-      - name: Capture start timestamp
-        id: start
-        shell: bash
-        run: |
-          set -euo pipefail
-          timestamp="$(date -u +%s)"
-          echo "timestamp=$timestamp" >> "$GITHUB_OUTPUT"
-
-      - name: Checkout repository
-        uses: actions/checkout@v7
-        with:
-          # Full history: the per-branch "since last successful run" check below
-          # needs to look arbitrarily far back if a prior run failed or was skipped.
-          fetch-depth: 0
-
-      - name: Fetch all branches
-        shell: bash
-        run: git fetch origin '+refs/heads/*:refs/remotes/origin/*'
-
-      - name: Scan branches and publish changed OFL profiles
-        shell: bash
-        env:
-          GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-          SCAN_UNTIL: ${{ steps.start.outputs.timestamp }}
-        run: |
-          set -euo pipefail
-
-          mapfile -t branches < <(
-            gh api "repos/${{ github.repository }}/branches" --paginate --jq '.[].name' \
-              | grep -E '^(main|release/v[0-9]+\.[0-9]+\.[0-9]+)$' | sort -u
-          )
-
-          # The cron run is the checkpoint: a successful run means every
-          # dispatched branch publisher completed and the pending queue was
-          # cleared. Manual or push-triggered post_merge_profiles runs are not
-          # checkpoints for this scan.
-          successful_cron_runs="$(gh api --method GET \
-            "repos/${{ github.repository }}/actions/workflows/ofl-ota-cronjob.yml/runs" \
-            -f status=success -f branch=main -f per_page=100 --paginate \
-            --jq '.workflow_runs[] | select((.display_title // "") | contains("[OFL barrier]"))')"
-          since="$(jq -rs 'sort_by(.run_started_at) | last.run_started_at // empty' <<< "$successful_cron_runs")"
-
-          for branch in "${branches[@]}"; do
-            echo "::group::$branch"
-
-            if [ -z "$since" ]; then
-              echo "No prior successful OFL cron run; checking $branch through $SCAN_UNTIL."
-              changed_files="$(git log --until="$SCAN_UNTIL" --name-only --pretty=format: "origin/$branch" -- \
-                resources/profiles/OrcaFilamentLibrary resources/profiles/OrcaFilamentLibrary.json \
-                | sed '/^$/d')"
-            else
-              changed_files="$(git log --since="$since" --until="$SCAN_UNTIL" --name-only --pretty=format: "origin/$branch" -- \
-                resources/profiles/OrcaFilamentLibrary resources/profiles/OrcaFilamentLibrary.json \
-                | sed '/^$/d')"
-            fi
-
-            if [ -n "$changed_files" ]; then
-              echo "OFL changed on $branch from ${since:-the beginning} through $SCAN_UNTIL:"
-              echo "$changed_files"
-              changed=true
-            else
-              echo "No OFL changes on $branch through $SCAN_UNTIL."
-              changed=false
-            fi
-
-            if [ "$changed" = true ]; then
-              dispatch_id="${GITHUB_RUN_ID}-${branch//\//-}"
-              # Record successful dispatches for the barrier step below.
-              # Branches whose workflow predates workflow_dispatch are skipped
-              # with a warning, as they were before the barrier was added.
-              if gh workflow run post_merge_profiles.yml \
-                --repo "${{ github.repository }}" \
-                --ref "$branch" \
-                -f vendor="$VENDOR" -f auto_publish=true \
-                -f ofl_cron_dispatch_id="$dispatch_id"; then
-                printf '%s\t%s\n' "$branch" "$dispatch_id" >> "$RUNNER_TEMP/ofl-dispatches.tsv"
-              else
-                echo "::warning::skipping $branch because post_merge_profiles.yml could not be dispatched at that ref"
-              fi
-            fi
-
-            echo "::endgroup::"
-          done
-
-      - name: Wait for OFL publishers
-        id: wait
-        shell: bash
-        env:
-          GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-          DISPATCHES_FILE: ${{ runner.temp }}/ofl-dispatches.tsv
-        run: |
-          set -euo pipefail
-
-          if [ ! -s "$DISPATCHES_FILE" ]; then
-            echo "No OFL publisher workflows were dispatched; pending queue will not be cleared."
-            echo "publishers_dispatched=false" >> "$GITHUB_OUTPUT"
-            exit 0
-          fi
-
-          : > "$RUNNER_TEMP/ofl-run-ids.tsv"
-          while IFS=$'\t' read -r branch dispatch_id; do
-            [ -n "$branch" ] || continue
-            echo "Waiting for OFL publisher on $branch ($dispatch_id)"
-
-            run_id=""
-            for _ in {1..120}; do
-              runs_json="$(gh api --method GET \
-                "repos/${{ github.repository }}/actions/workflows/post_merge_profiles.yml/runs" \
-                -f branch="$branch" -f event=workflow_dispatch -f per_page=100)"
-              run_id="$(jq -r --arg marker "[OFL cron $dispatch_id]" \
-                '[.workflow_runs[] | select((.display_title // "") | contains($marker))] \
-                | sort_by(.created_at) | last | .id // empty' <<< "$runs_json")"
-              [ -n "$run_id" ] && break
-              sleep 5
-            done
-
-            if [ -z "$run_id" ]; then
-              echo "::error::could not find dispatched post_merge_profiles run for $branch ($dispatch_id)"
-              exit 1
-            fi
-            printf '%s\t%s\n' "$branch" "$run_id" >> "$RUNNER_TEMP/ofl-run-ids.tsv"
-          done < "$DISPATCHES_FILE"
-
-          all_success=true
-          while IFS=$'\t' read -r branch run_id; do
-            [ -n "$run_id" ] || continue
-            echo "Watching OFL publisher run $run_id for $branch"
-            if ! gh run watch "$run_id" --repo "${{ github.repository }}" --exit-status; then
-              all_success=false
-            fi
-          done < "$RUNNER_TEMP/ofl-run-ids.tsv"
-
-          if [ "$all_success" != true ]; then
-            echo "::error::one or more OFL publisher workflows failed; pending queue will not be cleared"
-            exit 1
-          fi
-          echo "publishers_dispatched=true" >> "$GITHUB_OUTPUT"
-
-      - name: Clear OFL pending queue
-        if: steps.wait.outputs.publishers_dispatched == 'true'
-        shell: bash
-        env:
-          OTA_API_BASE_URL: ${{ vars.OTA_API_BASE_URL }}
-          OTA_API_KEY: ${{ secrets.OFL_OTA_PUBLISH_KEY }}
-          TIMESTAMP: ${{ steps.start.outputs.timestamp }}
-        run: |
-          set -euo pipefail
-          [ -n "$OTA_API_BASE_URL" ] || { echo "::error::vars.OTA_API_BASE_URL is not set"; exit 1; }
-          [ -n "$OTA_API_KEY" ] || { echo "::error::secrets.OFL_OTA_PUBLISH_KEY is not set"; exit 1; }
-
-          resp_file="$RUNNER_TEMP/ota-pending-clear-response.json"
-          status="$(curl -sS -o "$resp_file" -w '%{http_code}' -X POST \
-            "${OTA_API_BASE_URL%/}/api/v1/ota/ofl/pending/clear?timestamp=$TIMESTAMP" \
-            -H "Authorization: Bearer $OTA_API_KEY")"
-          body="$(cat "$resp_file")"
-          echo "$body"
-
-          if [ "$status" != "200" ]; then
-            echo "::error::OTA pending-clear call failed with HTTP $status"
-            exit 1
-          fi
@@ -5,9 +5,8 @@
 #             re-sliced on its own to see whether it changes the G-code
 #   harness - the GUI-vs-CLI parity harness (metrics only, never fails)
 # Both test the latest successful build_all.yml Linux AppImage from main, with
-# sources checked out at the commit that build was made from; a manual run can
-# name another branch, or pin one build by its run id. Nothing here gates a
-# build or a PR.
+# sources checked out at the commit that build was made from. Nothing here
+# gates a build or a PR.
 name: Parity Nightly

 on:
@@ -21,13 +20,9 @@ on:
        required: false
        default: "main"
      build_branch:
-        description: "branch whose newest successful build_all artifact to test (a PR build is the PR merged into its base; sources are checked out at the PR head)"
+        description: "branch whose latest successful build_all artifact to test"
        required: false
        default: "main"
-      build_run_id:
-        description: "build_all run id to test instead of build_branch's newest (same PR caveat)"
-        required: false
-        default: ""
      fixtures:
        description: "harness fixture ids, space-separated (empty = all)"
        required: false
@@ -55,53 +50,14 @@ jobs:
        env:
          GH_TOKEN: ${{ github.token }}
          GH_REPO: ${{ github.repository }}
-          BRANCH: ${{ inputs.build_branch || 'main' }}
-          RUN_ID: ${{ inputs.build_run_id }}
-          SCHEDULED: ${{ github.event_name == 'schedule' }}
        run: |
          set -euo pipefail
-          if [ -n "$RUN_ID" ]; then
-            [[ $RUN_ID =~ ^[0-9]+$ ]] || { echo "build_run_id must be a numeric run id, got '$RUN_ID'" >&2; exit 1; }
-            # a pinned build is read directly, not through a search; it must come
-            # from this repository, because the later jobs check out its commit here
-            found=$(gh api "repos/$GH_REPO/actions/runs/$RUN_ID" --jq \
-              'select(.path == ".github/workflows/build_all.yml" and .conclusion == "success"
-                      and .head_repository.full_name == env.GH_REPO)
-               | "\(.id) \(.head_sha) \(.created_at)"')
-            [ -n "$found" ] || { echo "run $RUN_ID is not a successful build_all run of $GH_REPO" >&2; exit 1; }
-          else
-            # GitHub serves filtered run listings (branch=, status=, head_sha=, ...)
-            # from a search index that has returned weeks-old results, while the
-            # unfiltered listing stays current, so list unfiltered and filter here.
-            # The repository check keeps out fork PRs whose branch has the same
-            # name. A feature branch is normally built only for its PR, and a PR
-            # build compiles the PR merged into its base rather than head_sha, so
-            # a build of the branch itself (push or dispatch) is preferred when
-            # the same page has one.
-            pick='([.workflow_runs[] | select(.head_branch == env.BRANCH and .conclusion == "success"
-                    and .head_repository.full_name == env.GH_REPO)]
-                   | map(select(.event != "pull_request"))[0] // .[0])
-                  | select(.) | "\(.id) \(.head_sha) \(.created_at)"'
-            # a page of 100 runs spans about a day and a half; a manual run may
-            # target a branch that last built weeks ago
-            pages=3
-            if [ "$SCHEDULED" != true ]; then pages=20; fi
-            found=""
-            for page in $(seq "$pages"); do
-              found=$(gh api "repos/$GH_REPO/actions/workflows/build_all.yml/runs?per_page=100&page=$page" --jq "$pick")
-              if [ -n "$found" ]; then break; fi
-            done
-            [ -n "$found" ] || { echo "no successful $BRANCH build among the last $((pages * 100)) build_all runs; pass build_run_id to test an older one" >&2; exit 1; }
-          fi
-          read -r run_id head_sha created <<< "$found"
-          # the nightly fails rather than report on a stale build
-          if [ "$SCHEDULED" = true ] && [ $(( $(date +%s) - $(date -d "$created" +%s) )) -gt 172800 ]; then
-            echo "newest $BRANCH build $run_id is from $created, over 48 hours old" >&2
-            exit 1
-          fi
-          printf 'run_id=%s\nhead_sha=%s\n' "$run_id" "$head_sha" >> "$GITHUB_OUTPUT"
+          gh run list --workflow build_all.yml \
+            --branch "${{ inputs.build_branch || 'main' }}" \
+            --status success --limit 1 --json databaseId,headSha \
+            --jq '"run_id=\(.[0].databaseId)\nhead_sha=\(.[0].headSha)"' \
+            >> "$GITHUB_OUTPUT"
          cat "$GITHUB_OUTPUT"
-          echo "Testing build [$run_id](https://github.com/$GH_REPO/actions/runs/$run_id) of \`$head_sha\`, built $created" >> "$GITHUB_STEP_SUMMARY"

  effect:
    name: Override sweep effect stage (shard ${{ matrix.shard }})
@@ -1,14 +1,5 @@
 name: Post-merge profiles

-run-name: >-
-  Post-merge profiles${{
-    inputs.ofl_cron_dispatch_id != '' &&
-    inputs.vendor == 'OrcaFilamentLibrary' &&
-    (inputs.auto_publish == true || inputs.auto_publish == 'true') &&
-    format(' [OFL cron {0}]', inputs.ofl_cron_dispatch_id) ||
-    ''
-  }}
-
 # Push-triggered counterpart to check_profiles.yml (which only gates PRs). When a
 # profile change lands on main or a release branch, rebuild the affected vendors'
 # binary preset caches (<vendor>.opc) and publish each as a versioned ZIP asset on
@@ -17,19 +8,6 @@ run-name: >-
 # only then does it become a live OTA update - this workflow does none of that
 # last part (no changelog, no R2, no webhook).
 #
-# A workflow_dispatch carrying a `vendor` input (e.g. the daily OFL cron - OFL has
-# no FOLDER_MERGERS grant, since it isn't merged through the PR merge-bot delegation
-# scheme) publishes that vendor directly and skips the FOLDER_MERGERS check below.
-# workflow_dispatch is already a trusted, explicit trigger, unlike the automatic
-# push-diff path the FOLDER_MERGERS check exists to gate.
-#
-# Separately, an ordinary push whose diff touches an OrcaFilamentLibrary company
-# folder (resources/profiles/OrcaFilamentLibrary/filament/<Company>/**) records
-# that PR as pending via POST /api/v1/ota/ofl/pending, regardless of whether
-# OrcaFilamentLibrary as a whole is authorized to publish in this same run - a
-# partner's OTA Manager dashboard should see a merged PR immediately, well
-# before the daily cron actually builds and publishes it.
-#
 # Asset contract expected by OrcaCloud's release scanner:
 #   ^(\d+\.\d+\.\d+)_([^_]+)_(\d+(?:\.\d+){3})_(\d{12})\.zip$
 #     <orca_ver>_<vendor>_<profile_version>_<UTC yyyymmddHHMM>.zip   (zip root: <vendor>.opc)
@@ -39,45 +17,16 @@ run-name: >-
 on:
  push:
    branches:
-    # once v2.5.0 stable is released, this will be removed, so nightly won't receive OTA updates.
    - main
-    # release/vX.Y.Z point-release branches only, not the release/vX.Y working
-    # branch profile PRs land on first - "v*.*.*" requires two literal dots,
-    # which release/vX.Y (one dot) doesn't have.
-    - release/v*.*.*
+    - release/*
    paths:
    - 'resources/profiles/**'
    - '.github/workflows/post_merge_profiles.yml'

  workflow_dispatch:
-    inputs:
-      vendor:
-        description: >-
-          Publish only this vendor, bypassing the FOLDER_MERGERS grant check.
-          For trusted explicit dispatches only (e.g. the OFL nightly cron).
-          Leave empty to fall back to diffing the triggering commit.
-        required: false
-        type: string
-      auto_publish:
-        description: >-
-          After publishing, also call the OTA auto-publish API to go live
-          immediately, skipping the human changelog/Publish step. Separate
-          from `vendor` on purpose: a maintainer can dispatch with just
-          `vendor` set to rebuild/republish an asset without it going live.
-          Only the OFL nightly cron should set this to true.
-        required: false
-        type: boolean
-        default: false
-      ofl_cron_dispatch_id:
-        description: >-
-          Unique marker supplied by the trusted OFL daily cron so it can find
-          and wait for this dispatched workflow run.
-        required: false
-        type: string

 permissions:
  contents: read
-  pull-requests: read  # commits/{sha}/pulls lookup in the OFL-pending step

 # One run per branch; let a run finish rather than cancel it, since it publishes.
 concurrency:
@@ -117,38 +66,8 @@ jobs:
        shell: bash
        env:
          FOLDER_MERGERS: ${{ vars.FOLDER_MERGERS }}
-          DISPATCH_VENDOR: ${{ github.event_name == 'workflow_dispatch' && inputs.vendor || '' }}
        run: |
          set -euo pipefail
-
-          # A vendor has a manifest plus either a preset directory or a version
-          # field; this drops non-vendor files such as blacklist.json. Shared by
-          # both the explicit-dispatch path below and the push-diff path further
-          # down, so the definition of "valid vendor" can't drift between them.
-          is_valid_vendor() {
-            local v="$1"
-            local json="resources/profiles/$v.json"
-            [ -f "$json" ] && { [ -d "resources/profiles/$v" ] || jq -e '.version' "$json" >/dev/null 2>&1; }
-          }
-
-          # Explicit vendor dispatch (e.g. the OFL cron): trust the caller and
-          # skip both the git-diff detection and the FOLDER_MERGERS check below.
-          if [ -n "$DISPATCH_VENDOR" ]; then
-            v="$DISPATCH_VENDOR"
-            # Becomes part of the release asset filename and the OTA API's
-            # payload; keep it to the same charset every real vendor name uses.
-            if ! [[ "$v" =~ ^[A-Za-z0-9]+$ ]]; then
-              echo "::error::vendor '$v' must be alphanumeric"
-              exit 1
-            fi
-            if ! is_valid_vendor "$v"; then
-              echo "::error::vendor '$v' has no resources/profiles/$v.json with a profile directory or version field"
-              exit 1
-            fi
-            echo "vendors=$v" >> "$GITHUB_OUTPUT"
-            exit 0
-          fi
-
          base='${{ github.event.before }}'
          head='${{ github.sha }}'
          # Zero SHA (branch created / force push) or manual dispatch: fall back
@@ -156,10 +75,6 @@ jobs:
          if [ -z "$base" ] || [ "$base" = "0000000000000000000000000000000000000000" ] || ! git cat-file -e "$base^{commit}" 2>/dev/null; then
            base="$head^"
          fi
-          # Exposed so the OFL-pending step below can reuse this exact diff
-          # range instead of re-deriving it (and drifting from this logic).
-          echo "base=$base" >> "$GITHUB_OUTPUT"
-          echo "head=$head" >> "$GITHUB_OUTPUT"
          mapfile -t candidates < <(
            git diff --name-only "$base" "$head" -- resources/profiles \
              | sed -nE 's#^resources/profiles/([^/]+)/.*#\1#p; s#^resources/profiles/([^/]+)\.json$#\1#p' \
@@ -169,7 +84,10 @@ jobs:
          vendors=()
          for v in "${candidates[@]:-}"; do
            [ -n "$v" ] || continue
-            if is_valid_vendor "$v"; then
+            json="resources/profiles/$v.json"
+            # A vendor has a manifest plus either a preset directory or a version
+            # field; this drops non-vendor files such as blacklist.json.
+            if [ -f "$json" ] && { [ -d "resources/profiles/$v" ] || jq -e '.version' "$json" >/dev/null 2>&1; }; then
              vendors+=("$v")
            fi
          done
@@ -183,9 +101,6 @@ jobs:
          # sibling bundle JSON are covered by at least one FOLDER_MERGERS
          # grant. The account part is intentionally ignored here: this is a
          # post-merge safety check, not an authorization check for a command.
-          # An ineligible vendor (e.g. OrcaFilamentLibrary, which has no grant)
-          # is dropped on its own - it never blocks other vendors in the same
-          # push from publishing.
          grants=()
          while IFS= read -r raw_line; do
            line="${raw_line#"${raw_line%%[![:space:]]*}"}"
@@ -212,29 +127,23 @@ jobs:
            return 1
          }

-          authorized=()
          unauthorized=()
          for v in "${vendors[@]}"; do
-            if is_granted "resources/profiles/$v" && is_granted "resources/profiles/$v.json"; then
-              authorized+=("$v")
-            else
+            if ! is_granted "resources/profiles/$v" || ! is_granted "resources/profiles/$v.json"; then
              unauthorized+=("$v")
            fi
          done

          if [ "${#unauthorized[@]}" -ne 0 ]; then
-            echo "::warning::skipping vendor(s) with no FOLDER_MERGERS grant (no asset built or published for them this run): ${unauthorized[*]}"
+            echo "vendors=" >> "$GITHUB_OUTPUT"
+            exit 0
          fi

-          echo "vendors=${authorized[*]}" >> "$GITHUB_OUTPUT"
+          echo "vendors=${vendors[*]}" >> "$GITHUB_OUTPUT"

      - name: Resolve Orca version
        id: orca
-        # Unconditional: needed both by the vendor-publish pipeline below (only
-        # when vendors is non-empty) and by the OFL-pending step at the end
-        # (which runs whenever OFL itself changed, even if vendors ends up
-        # empty because OFL has no FOLDER_MERGERS grant). Cheap and harmless
-        # to always resolve - version.inc is present on every commit.
+        if: steps.vendors.outputs.vendors != ''
        shell: bash
        run: |
          set -euo pipefail
@@ -333,132 +242,3 @@ jobs:
            echo "### Published to \`$repo\` release \`$RELEASE_TAG\`"
            for f in "$ASSET_DIR"/*.zip; do echo "- \`$(basename "$f")\`"; done
          } >> "$GITHUB_STEP_SUMMARY"
-
-      - name: Notify OTA auto-publish
-        # Gated on auto_publish specifically, not just "vendor was dispatched":
-        # a maintainer manually dispatching with vendor=OrcaFilamentLibrary (e.g.
-        # to rebuild/republish an asset while debugging) must not silently go
-        # live. Only a caller that explicitly opts in with auto_publish=true
-        # (the OFL nightly cron) skips the human changelog/Publish step.
-        if: >-
-          steps.vendors.outputs.vendors != '' && github.event_name == 'workflow_dispatch'
-          && (inputs.auto_publish == true || inputs.auto_publish == 'true')
-        shell: bash
-        env:
-          OTA_API_BASE_URL: ${{ vars.OTA_API_BASE_URL }}
-          OTA_API_KEY: ${{ secrets.OFL_OTA_PUBLISH_KEY }}
-          ASSET_DIR: ${{ steps.pkg.outputs.dir }}
-        run: |
-          set -euo pipefail
-          [ -n "$OTA_API_BASE_URL" ] || { echo "::error::vars.OTA_API_BASE_URL is not set"; exit 1; }
-          [ -n "$OTA_API_KEY" ] || { echo "::error::secrets.OFL_OTA_PUBLISH_KEY is not set"; exit 1; }
-
-          mapfile -t zip_files < <(cd "$ASSET_DIR" && ls -1 *.zip)
-          filenames_json="$(printf '%s\n' "${zip_files[@]}" | jq -R . | jq -s .)"
-          payload="$(jq -n --argjson filenames "$filenames_json" '{filenames: $filenames}')"
-
-          resp_file="$RUNNER_TEMP/ota-auto-publish-response.json"
-          status="$(curl -sS -o "$resp_file" -w '%{http_code}' -X POST \
-            "${OTA_API_BASE_URL%/}/api/v1/ota/auto-publish" \
-            -H "Authorization: Bearer $OTA_API_KEY" \
-            -H 'Content-Type: application/json' \
-            -d "$payload")"
-          body="$(cat "$resp_file")"
-          echo "$body"
-
-          if [ "$status" != "200" ]; then
-            echo "::error::OTA auto-publish call failed with HTTP $status"
-            exit 1
-          fi
-
-          # A 200 can still carry per-file "error" results (e.g. NOT_FOUND); the
-          # asset is already safely published to the profiles release above, but
-          # it never went live, so treat that as a failure worth surfacing loudly.
-          error_count="$(jq '[.results[] | select(.status == "error")] | length' <<< "$body")"
-          if [ "$error_count" != "0" ]; then
-            jq -r '.results[] | select(.status == "error") | "::error::\(.filename): \(.code) - \(.message)"' <<< "$body"
-            exit 1
-          fi
-
-      - name: Record OFL pending changes
-        # A real merge, never the cron's explicit-vendor dispatch (that's
-        # automation publishing, not a new merge to report). This covers two
-        # trigger shapes: an ordinary push, and a vendor-less workflow_dispatch
-        # - the latter is exactly what pr-merge-bot.yml's re-dispatch after a
-        # successful /bot merge looks like (a GITHUB_TOKEN-authored merge fires
-        # no push event at all, which is why that re-dispatch exists). Both
-        # land in the same diff-fallback path in "Resolve changed vendors", so
-        # base/head/orca_ver are already correctly populated either way - only
-        # this condition needs widening.
-        # Placed last in the job on purpose: a failure here must never block
-        # the vendor-publish pipeline above, which a step failing earlier in
-        # the job would do (subsequent steps without always() get skipped).
-        if: >-
-          github.event_name == 'push' ||
-          (github.event_name == 'workflow_dispatch' && !inputs.vendor)
-        shell: bash
-        env:
-          GH_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-          OTA_API_BASE_URL: ${{ vars.OTA_API_BASE_URL }}
-          OTA_API_KEY: ${{ secrets.OFL_OTA_PUBLISH_KEY }}
-        run: |
-          set -euo pipefail
-          base='${{ steps.vendors.outputs.base }}'
-          head='${{ steps.vendors.outputs.head }}'
-          orca_ver='${{ steps.orca.outputs.orca_ver }}'
-
-          # Only real vendor subdirectories under filament/, e.g.
-          # .../filament/Qidi/x.json -> "Qidi". This naturally excludes loose
-          # top-level files (.../filament/Generic PLA @System.json - no further
-          # slash to match) and is further filtered below to drop "base", the
-          # shared @base/@System inheritance folder, not a partner company.
-          mapfile -t ofl_companies < <(
-            git diff --name-only "$base" "$head" -- resources/profiles/OrcaFilamentLibrary/filament \
-              | sed -nE 's#^resources/profiles/OrcaFilamentLibrary/filament/([^/]+)/.*#\1#p' \
-              | grep -vx 'base' \
-              | sort -u
-          )
-
-          if [ "${#ofl_companies[@]}" -eq 0 ]; then
-            echo "No OFL company folders changed in this push."
-            exit 0
-          fi
-
-          [ -n "$OTA_API_BASE_URL" ] || { echo "::error::vars.OTA_API_BASE_URL is not set"; exit 1; }
-          [ -n "$OTA_API_KEY" ] || { echo "::error::secrets.OFL_OTA_PUBLISH_KEY is not set"; exit 1; }
-
-          # The head commit's own merged PR, not a per-commit walk: this
-          # assumes the ordinary one-PR-per-push shape every other merge path
-          # in this repo already assumes (pr-merge-bot.yml's re-dispatch logic
-          # does the same). A merge commit's parents don't matter here - this
-          # API call works the same regardless of merge strategy.
-          pr_json="$(gh api "repos/${{ github.repository }}/commits/$head/pulls" \
-            --jq '[.[] | select(.merged_at != null)] | sort_by(.merged_at) | last // empty')"
-
-          if [ -z "$pr_json" ]; then
-            echo "::warning::push $head touches OFL compan(y/ies) (${ofl_companies[*]}) but has no associated merged PR; skipping pending record(s)"
-            exit 0
-          fi
-          pr_number="$(jq -r '.number' <<< "$pr_json")"
-          pr_url="$(jq -r '.html_url' <<< "$pr_json")"
-          pr_title="$(jq -r '.title' <<< "$pr_json")"
-
-          for company in "${ofl_companies[@]}"; do
-            payload="$(jq -n --arg vendor "$company" --arg ver "$orca_ver" --argjson pr "$pr_number" \
-              --arg url "$pr_url" --arg title "$pr_title" \
-              '{vendor: $vendor, orcaSlicerVersion: $ver, prNumber: $pr, prUrl: $url, prTitle: $title}')"
-
-            resp_file="$RUNNER_TEMP/ofl-pending-$company.json"
-            status="$(curl -sS -o "$resp_file" -w '%{http_code}' -X POST \
-              "${OTA_API_BASE_URL%/}/api/v1/ota/ofl/pending" \
-              -H "Authorization: Bearer $OTA_API_KEY" \
-              -H 'Content-Type: application/json' \
-              -d "$payload")"
-            body="$(cat "$resp_file")"
-            echo "$body"
-
-            if [ "$status" != "200" ]; then
-              echo "::error::OFL pending record failed for vendor=$company (PR #$pr_number): HTTP $status"
-              exit 1
-            fi
-          done
@@ -56,9 +56,9 @@ You can do this in Environment Variables settings.
 endif ()

 if (APPLE)
-    # if CMAKE_OSX_DEPLOYMENT_TARGET is not set, set it to 12.0 (the lowest Xcode 27 accepts)
+    # if CMAKE_OSX_DEPLOYMENT_TARGET is not set, set it to 11.3
    if (NOT CMAKE_OSX_DEPLOYMENT_TARGET)
-        set(CMAKE_OSX_DEPLOYMENT_TARGET "12.0" CACHE STRING "Minimum OS X deployment version" FORCE)
+        set(CMAKE_OSX_DEPLOYMENT_TARGET "11.3" CACHE STRING "Minimum OS X deployment version" FORCE)
    endif ()
    message(STATUS "CMAKE_OSX_DEPLOYMENT_TARGET: ${CMAKE_OSX_DEPLOYMENT_TARGET}")
 endif ()
@@ -70,9 +70,6 @@ if (POLICY CMP0092)
    cmake_policy(SET CMP0092 NEW)
 endif ()

-# project() reads this, so set it first.
-set(CMAKE_USER_MAKE_RULES_OVERRIDE "${CMAKE_CURRENT_LIST_DIR}/cmake/modules/ClangClShowIncludes.cmake")
-
 project(OrcaSlicer)

 # Backward compatibility for old CMake versions
@@ -279,11 +276,6 @@ if (APPLE)
    endif()
    SET(CMAKE_XCODE_ATTRIBUTE_PRODUCT_BUNDLE_IDENTIFIER "com.orcaslicer.OrcaSlicer")

-    # The macOS CI jobs build with Ninja (build_release_macos.sh -x), so the Xcode generator
-    # is not covered. Xcode adds -Wshorten-64-to-32 by default ("Implicit Conversion to 32 Bit
-    # Type"); Ninja/-Wall does not, and under -Werror it fails Xcode builds on code CI accepts.
-    set(CMAKE_XCODE_ATTRIBUTE_GCC_WARN_64_TO_32_BIT_CONVERSION "NO")
-
    message(STATUS "Orca: IS_CROSS_COMPILE: ${IS_CROSS_COMPILE}")
 elseif (CMAKE_SYSTEM_NAME STREQUAL "Linux")
    set(CMAKE_INSTALL_RPATH "$ORIGIN")
@@ -834,37 +826,6 @@ find_package(OpenSSL REQUIRED)
 find_package(CURL REQUIRED)
 find_package(Freetype REQUIRED)

-if (SLIC3R_GUI)
-    # LibDataChannel's installed export references its bundled dependencies,
-    # but does not install their CMake targets. Recreate those targets from
-    # the same dependency prefix before loading the LibDataChannel config.
-    if (NOT TARGET Usrsctp::usrsctp)
-        find_library(_ORCA_USRSCTP_LIBRARY NAMES usrsctp
-            PATHS "${CMAKE_PREFIX_PATH}/lib" NO_DEFAULT_PATH)
-        if (_ORCA_USRSCTP_LIBRARY)
-            add_library(Usrsctp::usrsctp UNKNOWN IMPORTED GLOBAL)
-            set_target_properties(Usrsctp::usrsctp PROPERTIES
-                IMPORTED_LOCATION "${_ORCA_USRSCTP_LIBRARY}"
-                IMPORTED_LINK_INTERFACE_LANGUAGES C
-                INTERFACE_LINK_LIBRARIES "Threads::Threads")
-        endif()
-    endif()
-
-    if (NOT TARGET LibJuice::LibJuice)
-        find_library(_ORCA_LIBJUICE_LIBRARY NAMES juice
-            PATHS "${CMAKE_PREFIX_PATH}/lib" NO_DEFAULT_PATH)
-        if (_ORCA_LIBJUICE_LIBRARY)
-            add_library(LibJuice::LibJuice UNKNOWN IMPORTED GLOBAL)
-            set_target_properties(LibJuice::LibJuice PROPERTIES
-                IMPORTED_LOCATION "${_ORCA_LIBJUICE_LIBRARY}"
-                IMPORTED_LINK_INTERFACE_LANGUAGES C
-                INTERFACE_LINK_LIBRARIES "Threads::Threads")
-        endif()
-    endif()
-
-    find_package(LibDataChannel CONFIG REQUIRED)
-endif()
-

 add_library(libcurl INTERFACE)
 target_link_libraries(libcurl INTERFACE CURL::libcurl)
@@ -1145,7 +1106,6 @@ function(orcaslicer_copy_dlls target config postfix output_dlls)
    endif ()
    file(COPY ${_occt_dlls}
            ${CMAKE_PREFIX_PATH}/bin/freetype.dll
-            ${CMAKE_PREFIX_PATH}/bin/avformat-61.dll
            ${CMAKE_PREFIX_PATH}/bin/avcodec-61.dll
            ${CMAKE_PREFIX_PATH}/bin/swresample-5.dll
            ${CMAKE_PREFIX_PATH}/bin/swscale-8.dll
@@ -1158,11 +1118,11 @@ function(orcaslicer_copy_dlls target config postfix output_dlls)
        ${_out_dir}/WebView2Loader.dll

        ${_out_dir}/freetype.dll
-        ${_out_dir}/avformat-61.dll
        ${_out_dir}/avcodec-61.dll
        ${_out_dir}/swresample-5.dll
        ${_out_dir}/swscale-8.dll
        ${_out_dir}/avutil-59.dll
+        PARENT_SCOPE
    )
    list(APPEND _dll_list ${_occt_staged})
    set(${output_dlls} ${_dll_list} PARENT_SCOPE)
@@ -1182,10 +1142,7 @@ function(orcaslicer_copy_sos target config postfix output_sos)
        set(_out_dir "${CMAKE_CURRENT_BINARY_DIR}")
    endif ()

-    file(COPY ${CMAKE_PREFIX_PATH}/lib/libavformat.so
-            ${CMAKE_PREFIX_PATH}/lib/libavformat.so.61
-            ${CMAKE_PREFIX_PATH}/lib/libavformat.so.61.1.100
-            ${CMAKE_PREFIX_PATH}/lib/libavcodec.so
+    file(COPY ${CMAKE_PREFIX_PATH}/lib/libavcodec.so
            ${CMAKE_PREFIX_PATH}/lib/libavcodec.so.61
            ${CMAKE_PREFIX_PATH}/lib/libavcodec.so.61.3.100
            ${CMAKE_PREFIX_PATH}/lib/libavutil.so
@@ -1200,9 +1157,6 @@ function(orcaslicer_copy_sos target config postfix output_sos)
         DESTINATION ${_out_dir})

    set(${output_sos}
-        ${_out_dir}/libavformat.so
-        ${_out_dir}/libavformat.so.61
-        ${_out_dir}/libavformat.so.61.1.100
        ${_out_dir}/libavcodec.so
        ${_out_dir}/libavcodec.so.61
        ${_out_dir}/libavcodec.so.61.3.100
@@ -1332,8 +1286,6 @@ endif ()

 if (CMAKE_SYSTEM_NAME STREQUAL "Linux")
    set(LIBRARY_FILES
-    ${LIBDIR_BIN}/libavformat.so.61
-    ${LIBDIR_BIN}/libavformat.so.61.1.100
    ${LIBDIR_BIN}/libavcodec.so.61
    ${LIBDIR_BIN}/libavcodec.so.61.3.100
    ${LIBDIR_BIN}/libavutil.so.59
@@ -53,7 +53,7 @@ while getopts ":dpa:snt:xbc:i:j:Tuh" opt; do
        echo "   -s: Build slicer only"
        echo "   -u: Build universal app only (requires existing arm64 and x86_64 app bundles)"
        echo "   -n: Nightly build"
-        echo "   -t: Specify minimum version of the target platform, default is 12.0"
+        echo "   -t: Specify minimum version of the target platform, default is 11.3"
        echo "   -x: Use Ninja Multi-Config CMake generator, default is Xcode"
        echo "   -b: Build without reconfiguring CMake"
        echo "   -c: Set CMake build configuration, default is Release"
@@ -95,7 +95,7 @@ if [ -z "$DEPS_CMAKE_GENERATOR" ]; then
 fi

 if [ -z "$OSX_DEPLOYMENT_TARGET" ]; then
-  export OSX_DEPLOYMENT_TARGET="12.0"
+  export OSX_DEPLOYMENT_TARGET="11.3"
 fi

 if [ -z "$CMAKE_IGNORE_PREFIX_PATH" ]; then
@@ -1,10 +0,0 @@
-# ccache does not parse the -clang: arguments CMake uses for clang-cl's gcc-style
-# depfile, so a cache hit writes the object and no depfile, and Ninja then records
-# no headers for that object. ccache reproduces /showIncludes output on a hit.
-foreach (_lang C CXX)
-    if (CMAKE_${_lang}_COMPILER_ID STREQUAL "Clang" AND
-        CMAKE_${_lang}_COMPILER_FRONTEND_VARIANT STREQUAL "MSVC")
-        set(CMAKE_DEPFILE_FLAGS_${_lang} "/showIncludes")
-        set(CMAKE_${_lang}_DEPFILE_FORMAT msvc)
-    endif ()
-endforeach ()
@@ -26,9 +26,9 @@ endif()

 cmake_minimum_required(VERSION 3.2)
 if (APPLE)
-    # if CMAKE_OSX_DEPLOYMENT_TARGET is not set, set it to 12.0 (the lowest Xcode 27 accepts)
+    # if CMAKE_OSX_DEPLOYMENT_TARGET is not set, set it to 11.3
    if (NOT CMAKE_OSX_DEPLOYMENT_TARGET)
-        set(CMAKE_OSX_DEPLOYMENT_TARGET "12.0" CACHE STRING "Minimum OS X deployment version" FORCE)
+        set(CMAKE_OSX_DEPLOYMENT_TARGET "11.3" CACHE STRING "Minimum OS X deployment version" FORCE)
    endif ()
    message(STATUS "CMAKE_OSX_DEPLOYMENT_TARGET: ${CMAKE_OSX_DEPLOYMENT_TARGET}")

@@ -38,14 +38,6 @@ if(POLICY CMP0135) # DOWNLOAD_EXTRACT_TIMESTAMP
    cmake_policy(SET CMP0135 NEW)
 endif()

-# project() reads this, so set it first. scripts/flatpak/make_deps_tar.sh packs deps/
-# without cmake/, so the file is missing in a Flatpak build.
-set(_rules_override "${CMAKE_CURRENT_LIST_DIR}/../cmake/modules/ClangClShowIncludes.cmake")
-if (EXISTS "${_rules_override}")
-    set(CMAKE_USER_MAKE_RULES_OVERRIDE "${_rules_override}")
-endif ()
-unset(_rules_override)
-
 project(OrcaSlicer-deps)

 # Backward compatibility for old CMake versions
@@ -164,7 +156,7 @@ if (NOT _is_multi AND NOT CMAKE_BUILD_TYPE)
 endif ()

 function(orcaslicer_add_cmake_project projectname)
-    cmake_parse_arguments(P_ARGS "FORWARD_CONFIG" "INSTALL_DIR;BUILD_COMMAND;INSTALL_COMMAND;SOURCE_DIR" "CMAKE_ARGS" ${ARGN})
+    cmake_parse_arguments(P_ARGS "FORWARD_CONFIG" "INSTALL_DIR;BUILD_COMMAND;INSTALL_COMMAND" "CMAKE_ARGS" ${ARGN})

    # MSVC is true for clang-cl as well, so the sub-build toolchain has to key on the
    # generator. A non-Visual-Studio superbuild passes its own generator down, and with
@@ -210,18 +202,12 @@ function(orcaslicer_add_cmake_project projectname)
      set(_build_j "-j${NPROC}")
    endif ()

-    set(_source_dir_arg "")
-    if (P_ARGS_SOURCE_DIR)
-        set(_source_dir_arg SOURCE_DIR ${P_ARGS_SOURCE_DIR})
-    endif ()
-
 if (NOT IS_CROSS_COMPILE OR NOT APPLE)
    ExternalProject_Add(
        dep_${projectname}
        EXCLUDE_FROM_ALL    ON
        INSTALL_DIR         ${DESTDIR}
        DOWNLOAD_DIR        ${DEP_DOWNLOAD_DIR}/${projectname}
-        ${_source_dir_arg}
        ${_gen}
        CMAKE_ARGS
            -DCMAKE_POLICY_VERSION_MINIMUM=3.5
@@ -234,7 +220,6 @@ if (NOT IS_CROSS_COMPILE OR NOT APPLE)
            -DCMAKE_CXX_COMPILER:STRING=${CMAKE_CXX_COMPILER}
            -DCMAKE_C_COMPILER_LAUNCHER:STRING=${CMAKE_C_COMPILER_LAUNCHER}
            -DCMAKE_CXX_COMPILER_LAUNCHER:STRING=${CMAKE_CXX_COMPILER_LAUNCHER}
-            -DCMAKE_USER_MAKE_RULES_OVERRIDE:STRING=${CMAKE_USER_MAKE_RULES_OVERRIDE}
            -DCMAKE_TOOLCHAIN_FILE:STRING=${CMAKE_TOOLCHAIN_FILE}
            -DCMAKE_EXE_LINKER_FLAGS:STRING=${CMAKE_EXE_LINKER_FLAGS}
            -DCMAKE_SHARED_LINKER_FLAGS:STRING=${CMAKE_SHARED_LINKER_FLAGS}
@@ -255,14 +240,12 @@ if (NOT IS_CROSS_COMPILE OR NOT APPLE)
        # note for future devs: shared libs may actually create a size reduction
        # but orcaslicer_deps tends to get really funny regarding linking after that (notably boost)
        # so, as much as I would like to use that, it's not happening
-        if (NOT P_ARGS_SOURCE_DIR)
-            ExternalProject_Add_Step(dep_${projectname} free_download_space
-                    DEPENDEES download # do after download
-                    COMMENT "Freeing Space: Removing source archive"
-                    WORKING_DIRECTORY ${DEP_DOWNLOAD_DIR}
-                    COMMAND ${CMAKE_COMMAND} -E rm -rf ${projectname}
-            )
-        endif ()
+        ExternalProject_Add_Step(dep_${projectname} free_download_space
+                DEPENDEES download # do after download
+                COMMENT "Freeing Space: Removing source archive"
+                WORKING_DIRECTORY ${DEP_DOWNLOAD_DIR}
+                COMMAND ${CMAKE_COMMAND} -E rm -r ${projectname}
+        )
        ExternalProject_Add_Step(dep_${projectname} free_build_space
                DEPENDEES install # do after install
                COMMENT "Freeing Space: Removing source and build files"
@@ -276,7 +259,6 @@ else()
        EXCLUDE_FROM_ALL    ON
        INSTALL_DIR         ${DESTDIR}
        DOWNLOAD_DIR        ${DEP_DOWNLOAD_DIR}/${projectname}
-        ${_source_dir_arg}
        ${_gen}
        CMAKE_ARGS
            -DCMAKE_POLICY_VERSION_MINIMUM=3.5
@@ -285,7 +267,6 @@ else()
            -DCMAKE_IGNORE_PREFIX_PATH:STRING=${CMAKE_IGNORE_PREFIX_PATH}
            -DCMAKE_C_COMPILER_LAUNCHER:STRING=${CMAKE_C_COMPILER_LAUNCHER}
            -DCMAKE_CXX_COMPILER_LAUNCHER:STRING=${CMAKE_CXX_COMPILER_LAUNCHER}
-            -DCMAKE_USER_MAKE_RULES_OVERRIDE:STRING=${CMAKE_USER_MAKE_RULES_OVERRIDE}
            -DBUILD_SHARED_LIBS:BOOL=OFF
            ${_cmake_osx_arch}
            "${_configs_line}"
@@ -405,6 +386,10 @@ include(libnoise/libnoise.cmake)

 include(Draco/Draco.cmake)

+include(FFMPEG/FFMPEG.cmake)
+include(Assimp/Assimp.cmake)
+
+
 # I *think* 1.1 is used for *just* md5 hashing?
 # 3.1 has everything in the right place, but the md5 funcs used are deprecated
 # a grep across the repo shows it is used for other things
@@ -415,12 +400,6 @@ if(NOT OPENSSL_FOUND)
    set(OPENSSL_PKG dep_OpenSSL)
 endif()

-include(FFMPEG/FFMPEG.cmake)
-include(Assimp/Assimp.cmake)
-
-include(DataChannel/DataChannel.cmake)
-set(DATACHANNEL_PKG dep_DataChannel)
-
 # we don't want to load a "wrong" openssl when loading curl
 # so, just don't even bother
 # ...i think this is how it works? change if wrong
@@ -494,7 +473,6 @@ set(_dep_list
    dep_wxInspector
    dep_FFMPEG
    dep_Assimp
-    ${DATACHANNEL_PKG}
    )

 if (MSVC)
@@ -1,37 +0,0 @@
-# libdatachannel is the native ICE/DTLS/SCTP implementation used by the
-# GUI WebRTC camera controller. Keep the source revision fixed: the signaling
-# protocol is evolving independently of this transport dependency.
-#
-# It vendors plog, usrsctp and libjuice as git submodules, which a plain
-# GitHub tag tarball does not include. The flatpak sandbox has no network
-# access during the build, so there the manifest itself clones the repo
-# (submodules and all) into the dependency download directory before the
-# sandbox closes. ExternalProject_Add is pointed at that existing checkout
-# instead of being given its own network-dependent download method.
-if (FLATPAK)
-    set(_datachannel_source
-        SOURCE_DIR ${DEP_DOWNLOAD_DIR}/DataChannel
-    )
-else()
-    set(_datachannel_source
-        GIT_REPOSITORY https://github.com/paullouisageneau/libdatachannel.git
-        GIT_TAG v0.24.5
-        GIT_SHALLOW ON
-        GIT_SUBMODULES_RECURSE ON
-    )
-endif()
-
-orcaslicer_add_cmake_project(DataChannel
-    DEPENDS ${OPENSSL_PKG}
-    CMAKE_ARGS
-        -DNO_EXAMPLES=ON
-        -DNO_TESTS=ON
-        -DNO_WEBSOCKET=ON
-        -DNO_MEDIA=ON
-        -DUSE_NICE=OFF
-        -DUSE_SYSTEM_JUICE=OFF
-        -DUSE_SYSTEM_USRSCTP=OFF
-        -DOPENSSL_ROOT_DIR:PATH=${DESTDIR}
-        -DOPENSSL_USE_STATIC_LIBS=ON
-    ${_datachannel_source}
-)
@@ -1,26 +1,14 @@
 set(_conf_cmd ./configure)

-set(_ffmpeg_depends)
-set(_ffmpeg_configure_command ${_conf_cmd})
-if (TARGET dep_OpenSSL)
-    set(_ffmpeg_depends DEPENDS dep_OpenSSL)
-    set(_ffmpeg_configure_command
-        ${CMAKE_COMMAND} -E env
-        "PKG_CONFIG_PATH=${DESTDIR}/lib/pkgconfig:$ENV{PKG_CONFIG_PATH}"
-        ${_conf_cmd}
-    )
-endif()
-
 if (MSVC)
    set(_source_dir "${CMAKE_BINARY_DIR}/dep_FFMPEG-prefix/src/dep_FFMPEG")

-    set(PREBUILD_URL_arm64 "https://github.com/Noisyfox/FFmpeg-Builds-Orca/releases/download/autobuild-2026-09-18-16-50/ffmpeg-n7.0.3-33-g887d4b4919-winarm64-orca-shared-7.0.zip")
-    set(PREBUILD_HASH_arm64 "da480cbb39680056de824c57ec4dc3bd577b479ebbc310ff1f9dc55cf014b4c1")
-    set(PREBUILD_URL_x64 "https://github.com/Noisyfox/FFmpeg-Builds-Orca/releases/download/autobuild-2026-09-18-16-50/ffmpeg-n7.0.3-33-g887d4b4919-win64-orca-shared-7.0.zip")
-    set(PREBUILD_HASH_x64 "85da19daf198f5548259d8aabb349db84997a3f6e6886d8d7764114add9c6dae")
+    set(PREBUILD_URL_arm64 "https://github.com/Noisyfox/FFmpeg-Builds-Orca/releases/download/autobuild-2026-07-17-14-28/ffmpeg-n7.0.3-31-g9b6ffd74b5-winarm64-orca-shared-7.0.zip")
+    set(PREBUILD_HASH_arm64 "12f4140279f2f8469885e1b5b2e8be9d788882914c21523cacd56989f3548054")
+    set(PREBUILD_URL_x64 "https://github.com/Noisyfox/FFmpeg-Builds-Orca/releases/download/autobuild-2026-07-17-14-28/ffmpeg-n7.0.3-31-g9b6ffd74b5-win64-orca-shared-7.0.zip")
+    set(PREBUILD_HASH_x64 "e65916020ddb9ef84b2666dfbcbfc9b1d67f69d15b4a66db53754637bf2d498c")

    ExternalProject_Add(dep_FFMPEG
-        ${_ffmpeg_depends}
        URL ${PREBUILD_URL_${DEPS_ARCH}}
        URL_HASH SHA256=${PREBUILD_HASH_${DEPS_ARCH}}
        DOWNLOAD_DIR ${DEP_DOWNLOAD_DIR}/FFMPEG
@@ -33,8 +21,6 @@ if (MSVC)
    )

 else ()
-    set(_openssl_cmd --enable-openssl)
-
    if (APPLE)
        set(_minos_cmd
            "--extra-cflags=-mmacosx-version-min=${DEP_OSX_TARGET}"
@@ -66,11 +52,10 @@ else ()
    endif()

    ExternalProject_Add(dep_FFMPEG
-        ${_ffmpeg_depends}
        URL https://github.com/FFmpeg/FFmpeg/archive/refs/tags/n7.0.3.tar.gz
        URL_HASH SHA256=DEEDCABE339165214A3637DF4C86A507AEF0D793CF8774FF68735F4737E8DDBC
        DOWNLOAD_DIR ${DEP_DOWNLOAD_DIR}/FFMPEG
-        CONFIGURE_COMMAND ${_ffmpeg_configure_command}
+        CONFIGURE_COMMAND ${_conf_cmd}
            ${_cross_cmd}
            ${_pic_cmd}
            ${_arch_cmd}
@@ -78,21 +63,20 @@ else ()
            "--prefix=${DESTDIR}"
            ${_link_cmd}
            ${_minos_cmd}
-            ${_openssl_cmd}
            --disable-doc
            --enable-small
            --disable-outdevs
            --disable-filters
            --enable-filter=*null*,afade,*fifo,*format,*resample,aeval,allrgb,allyuv,atempo,pan,*bars,color,*key,crop,draw*,eq*,framerate,*_qsv,*_vaapi,*v4l2*,hw*,scale,volume,test*
            --disable-protocols
-            --enable-protocol=file,fd,pipe,http,https,rtp,tcp,udp
+            --enable-protocol=file,fd,pipe,rtp,udp
            --disable-muxers
            --enable-muxer=rtp
            --disable-encoders
            --disable-decoders
            --enable-decoder=*aac*,h264*,mp3*,mjpeg,rv*
            --disable-demuxers
-            --enable-demuxer=h264,mp3,mov,mpjpeg,rtsp,sdp
+            --enable-demuxer=h264,mp3,mov
            --disable-zlib
            --disable-avdevice
        BUILD_IN_SOURCE ON
@@ -1,137 +0,0 @@
-# Deferred Page Construction: High Level Design
-
-## Why it exists
-
-The main window is a notebook of tabs, and only one of them is on screen when the first
-frame appears. Others are opened later in the session, some never, and some only exist
-for certain printers. Building every tab before the first frame makes each startup pay for
-tabs the user may never open.
-
-This subsystem builds a tab the first time it is shown, and builds the rest in small units
-while the user is idle after startup. Startup pays only for what the first frame shows,
-the other tabs are usually ready before anyone opens them, and a click that lands in the
-middle of the idle build waits for one unit at most. Work that is not a tab, such as a
-dialog or the 3D view's GL resources, uses the same machinery.
-
-## The parts
-
-The parts are independent. A holder can hold anything a factory makes, a placeholder page
-is a holder with a widget, a staged object can live outside a holder, and the scheduler
-knows none of them; it runs tasks, which the main window makes from the holders.
-
-### The holder: `Lazy<T>`
-
-A holder keeps one object and the factory that makes it. The rest of the app reads the
-object if it exists, makes sure it exists now when about to show or navigate to it, or runs
-something once it exists. A type with one instance in the app gets these as statics
-through `LazyInstance<T>`, so callers need no reference to the main window, and all of them
-are harmless while no holder exists.
-
-The holder guarantees that callers see the object only once it is completely built. A
-build cannot re-enter itself, so a nested request finds nothing yet, and a factory that
-returns null or a unit that throws leaves the holder and the scheduler able to carry on.
-The holder does not own the object; its wx parent does, as for any window. The holder has
-no wx dependency and is unit-tested.
-
-### The placeholder page: `LazyPage<Panel>`
-
-The notebook needs a page object for a tab to exist and for tabs to be inserted and
-removed by pointer, and the placeholder is that object. It builds the real panel inside
-itself the first time it is shown and forwards showing and hiding afterwards, so a panel's
-own show handling stays its activation hook. Nothing builds while the main window is
-hidden; the window's first show builds the start page. A page that is out of the book is
-not prebuilt. A panel built while its page is hidden stays hidden, and gets the theming
-the window applied before the panel existed.
-
-### Staged construction: `StagedBuild`
-
-A constructor too big to be one unit builds a skeleton and queues the rest as steps, which
-run one per unit. A child panel's steps can be forwarded to its parent, and the parent is
-complete only once the child is. Nothing may use what a step builds before the last step
-has run, so staged panels follow these constraints:
-
- members created in steps start out null, so a partly built panel can be destroyed;
- timers, event handlers and destructors that touch step content check that the panel is
-  complete first;
- nothing takes focus while off screen, since a unit may run while the user is typing
-  elsewhere;
- a widget added by a step keeps its place in the sizer through an empty slot the skeleton
-  creates.
-
-### The scheduler: `IdleScheduler` and `PrebuildQueue`
-
-The queue holds tasks in order, and a slice runs units of the first pending task until
-the task finishes, the time budget is spent, or input arrives. It has no wx dependency and
-is unit-tested with a fake clock. A task whose work goes away, such as a tab removed from
-the book, is skipped, and becomes pending again if the work comes back.
-
-A slice runs only once the user has been idle for a short quiet time, and each slice is its
-own timer message, so paint, timers and input queued in between are handled before the
-next slice. Posting slices as pending events would not do that, because wx drains every
-pending event before the next native message. On GTK a timer that is always due starves
-the lower-priority sources that repaint and deliver posted events, so slices are a few
-milliseconds apart. On Windows a slice also waits while the native queue holds input,
-not counting mouse moves, which Windows synthesizes whenever a window appears under the
-cursor. A slice never runs inside a `wxYield()`, where it would build pages in the middle of
-the code that yielded. A unit cannot be interrupted, so the largest unit bounds how long a
-click can wait.
-When nothing is pending the timer stops and the subsystem costs nothing.
-
-The main window owns the scheduler because it owns what the tasks build, and clearing the
-queue with the window keeps a task from outliving its object. Each owner provides its own
-tasks, such as a tab, a dialog, the Prepare tab's settings page one option group at a
-time, the Prepare page's layout at the size the book gives its pages, or the 3D view's GL
-resources.
-
-### The 3D view's GL resources
-
-OpenGL is loaded on the Prepare tab's canvas. When the start page is not Prepare, loading
-it is an idle task that makes the context current on the hidden canvas, so the start page
-paints first and Prepare never appears. Loading it on a shown canvas under `Freeze()` holds
-back the start page's paint, and on GTK `Freeze()` cannot hide the canvas, which is a
-native child window or a Wayland subsurface drawn outside GTK. A hidden Windows child
-window keeps its device context, macOS attaches the context to a hidden view, and GTK
-creates the canvas's surface when the widget is realized, so on GTK the task realizes the
-canvas first. If the context cannot be made current, the canvas's first render loads the
-resources.
-
-## Rules
-
-**Before the first frame.** Only the start page and the Prepare tab's plater are built
-before the first frame. Everything else goes through a holder.
-
-**Reaching a lazy object.** Callers use the type's statics. Reading it if built is for
-things the object can live without, such as a rescale, a color change or a status refresh.
-Making sure it exists is for navigating to it or showing it. Running something once it is
-built is for state it would not fetch for itself on construction. A panel that pulls its
-state when constructed only ever needs to be read if built.
-
-**Unit size.** A unit should fit in one slice on a fast machine. A constructor over that is
-staged, and a single widget over it is accepted unless the widget itself can be split.
-
-**Order.** Tasks run cheapest and most likely to be opened first. Each holder's order is
-given where it is created, with gaps so a new task fits between its neighbors. A negative
-order is never prebuilt, for something few sessions open that costs more to build unasked
-than it saves.
-
-## Adopting it
-
-A lazy tab needs a panel type deriving from `LazyInstance`, a placeholder page the main
-window creates once with its order and registers for the idle build, and every use of the
-panel outside the main window going through the statics. Its constructor has to cope with
-the main window already existing and the user being busy elsewhere, so it takes no focus
-while off screen, and it does all of its own setup, since the main window does nothing to a
-panel after creating it.
-
-To stage a heavy constructor, keep the skeleton in the constructor, move the rest into
-steps in its original order, and follow the staged-construction constraints. Measure the
-units; a step that is still one big widget is split inside the widget or accepted.
-
-## Verifying
-
-The log lists the queue when it is registered, reports each completed task at info level
-and each slice and unit at debug level, and reports every on-demand build with its units
-and time. A task's completion line counts only the slice it finished in. A run from the
-configured start page should show every registered task complete in order, with no unit
-longer than intended. A click on a tab during the idle build should show an on-demand
-build for what was left, with the slices resuming once the user is idle again.
@@ -1,123 +0,0 @@
-# Multiline infill — High Level Design
-
-## Purpose and scope
-
-`fill_multiline` prints every sparse infill wall as N adjacent lines instead of
-one, so a wall is `d1 = N * spacing` thick. Only internal sparse infill uses it.
-Each pattern first builds its single-line centerlines at N times the usual line
-spacing (so the density holds), and `multiline_fill()` then replaces each
-centerline by the lines of that wall: the centerline itself when N is odd, and
-closed outlines around it at every `spacing` out to `d1 / 2`. The outlines are
-clipped to the fill region contracted by half a line width, then connected like
-any other infill.
-
-Outlines of centerlines that cross each other overlap at every crossing, which
-over-extrudes the wall intersections. The line-crossing patterns Grid,
-Triangles, Tri-hexagon and Cubic therefore build centerlines that never cross
-(`FillRectilinear::fill_surface_trapezoidal()`), and so do Adaptive Cubic and
-Support Cubic (`FillAdaptive`); the other patterns outline their usual
-centerlines.
-
-## Non-crossing centerlines
-
-The crossing lines are resolved into x-monotone paths, the levels of the line
-arrangement: walking along x, the k-th path is always the k-th line from the
-bottom. At every crossing, the two paths bounce off each other instead of
-passing through. Adjacent paths meet only at crossings, so their outlines touch
-there and nowhere overlap.
-
-Where two paths meet, each is cut short by a line perpendicular to the bisector
-of its bend, `d1 / 2` from the crossing. The two cut segments are parallel and
-`d1` apart, so the outermost lines of the two walls sit exactly `spacing` apart,
-like the lines inside a wall. Where three lines meet at one point, the middle
-path runs straight through and the outer two are cut `d1` from it.
-
-Each pattern builds its rows along x in a rotated frame. Grid lines run at ±45°
-there, and its rows are trapezoid waves that transpose on alternate layers. The three families of Triangles, Tri-hexagon and
-Cubic run at 0°, 60° and 120°. Those rows rotate by 120° every layer about a
-3-fold center of the arrangement, so each family takes every role in turn.
-The pattern is phased on fixed positions, so it lines up across layers and
-across the regions of one layer. Rounding the corners with
-`sparse_infill_smooth_factor` happens before `multiline_fill()`.
-
-## Cubic
-
-Single-line Cubic draws the three families at the same spacing `h` and shifts
-them with z: by `+dx`, `-dx` and `+dx`, `dx = z / sqrt(2)`. The multiline paths
-follow the same lines. In the frame where one family is horizontal, the other two
-cross in rows `h` apart, alternating by half a period, at height
-`tau = -3 * dx (mod h)` above the horizontal line below them. The crossings split
-every band between horizontal lines into up-pointing triangles of height `tau`,
-down-pointing triangles of height `h - tau`, and hexagons. At `tau = 0` (and `h`)
-all three families meet at common points, as in Triangles. At `tau = h / 2` the
-triangles are equal, as in Tri-hexagon. The origin of that frame is always a
-3-fold center, whatever z is, so the per-layer rotation keeps the lines in place.
-
-Each band holds two paths that touch at its crossings: the upper one takes the
-V below the crossing and runs along the top horizontal line, and the lower one
-takes the inverted V above it and runs along the bottom line. Both are the same function
-of `tau`, the lower one mirrored with `h - tau`. `cubic_upper_level()` builds one
-period of the upper path as the lower envelope of five lines, clipped from below:
-
- the two slanted lines through the crossings,
- the horizontal line, lowered when the triangle above it is less than `1.5 * d1` high,
- the two chamfers where the path turns onto and off the horizontal line, `d1 / 2`
-  from those crossings,
- the flat cut into the V at the crossing.
-
-The cut height `clamp(tau - d1 / 2, 0, h - d1) + d1` is what makes the pattern
-continuous in z. While both triangles are at least `1.5 * d1` high, every
-crossing is a pair of bends `d1 / 2` from it, as in Tri-hexagon. When a triangle
-is thinner, its three paths stack like a triple crossing. The path through it
-flattens toward its base line and lies on it once the triangle is under `d1 / 2`
-high, and the paths beside it are pushed `d1` away. The layout thus reaches the
-Triangles one where the families meet. Adjacent paths stay at least `d1` apart
-at every `tau` and at every density up to 100%.
-
-## Adaptive Cubic
-
-Adaptive Cubic and Support Cubic take their lines from an octree of cubes
-standing on a corner. On each layer every cube cuts its three mid-planes into
-segments of the same three 60° families as Cubic, but the pattern is not
-periodic. Smaller cubes near the surface add finer lines, and a finer line ends
-where it meets the wall of its coarser cube, so the lines form crossings and
-T-junctions. `FillAdaptive::multiline_paths()` builds the paths from these
-segments directly, for each fill region and within `4 * d1` of it.
-
-At a crossing the two paths bounce as in Cubic. At a T-junction the through line
-runs straight on and the path of the ending line stops there. Every path still
-runs left to right in the frame where one family is horizontal, and that family
-rotates with the layer.
-
-Every line of every cube size lies on one fine lattice, so crossings closer than
-a few `d1` are the corners of one small triangle of that lattice, as in Cubic.
-The cuts follow the Cubic rules without a closed formula:
-
- The two bends of a crossing are cut `d1` apart, `d1 / 2` each, perpendicular
-  to their bisector, so their walls touch. A cut goes no further than the path
-  end, and the other bend takes the rest of `d1`.
- At the tip of a small triangle, between the two slanted families, a cut also
-  goes no further than the neighbouring bend turning the other way, and the
-  path beyond that bend is kept a wall away from it. The bends onto the
-  horizontal family are not limited this way: pushing their paths apart would
-  open gaps between walls that should touch.
- A cut moves the path only where the cut line lies beyond it, near its bend.
-  The sharp bends between the two slanted families are cut after the bends onto
-  the horizontal family, so the tip of a small triangle wins, as in Cubic.
- A path stopping at a T-junction is trimmed until it is `d1` less half a line
-  spacing from every other path, so that its end overlaps the wall it stops on
-  by half a line and bonds to it. The paths are trimmed one at a time against
-  the others as already trimmed, so two ends facing each other meet instead of
-  both backing off. A path stopping on the line of another is trimmed before
-  that one, so it gives way and the other still reaches the line it stops on. A
-  second round trims every path again from its full length, so an end grows
-  back where the ends it gave way to were trimmed later, and a last round only
-  shortens them, keeping them that far apart. Paths shorter than `d1` are left
-  out.
- A line that ends on another less than `2 * d1` past a crossing stops at that
-  crossing instead, the shorter one where both do. The path along such a stub
-  would be trimmed away, leaving a hole between the walls that were cut to
-  touch it.
-
-Short paths enclosed by coarser lines still print as closed outlines, but most
-paths run on across several cells.
@@ -76,10 +76,9 @@ and the count of errors the original parse hit.

 Each entry is one preset **in source form**: what its JSON sub-file states and nothing
 that resolving it derives — the preset's own config diff, the name of the preset it
-inherits, the names of the presets it includes, and the parse metadata (name, sub-path,
-description, instantiation, setting and filament ids, renames). Non-instantiated base
-presets are stored too; the children that inherit from or include them cannot resolve
-without them.
+inherits, and the parse metadata (name, sub-path, description, instantiation, setting
+and filament ids, renames). Non-instantiated base presets are stored too; the children
+that inherit from them cannot resolve without them.

 **The payload names its own keys.** The dictionary holds the distinct `opt_key`s the
 file uses, the `ConfigOptionType` each was written as, and the distinct enum *value
@@ -162,9 +161,9 @@ cache nothing can invalidate is worse than no cache.

 Vendors load in a fixed order, because filament inheritance crosses exactly one
 boundary: any vendor's filament may inherit from the shared Orca filament library,
-and nothing else reaches across vendors — an `include` is always vendor-local. The
-library therefore goes first, alone; every other vendor follows in parallel, resolving
-against it; and the results are merged in a stable order:
+and nothing else reaches across vendors. The library therefore goes first, alone;
+every other vendor follows in parallel, resolving against it; and the results are
+merged in a stable order:

 ```mermaid
 flowchart LR
@@ -212,16 +211,13 @@ and its cache was never written back.

 Serving from a cache is not a memory-image restore. The entries are deserialized and
 then installed one by one — inheritance resolved against the presets installed before
-them and the currently loaded filament library, includes layered in, configs flattened
-onto the collection defaults, validated and registered — by the same function the JSON
-path calls straight after parsing a sub-file. An `include` layers what the included
-base states, between the parent and the preset's own keys: the base's diff against the
-default, taken when the base itself was installed and before the per-variant padding
-`inherits` sees, so only what a template sets reaches the presets including it. The two
-paths share everything below the parse, which is what makes a cache-loaded bundle
-indistinguishable from a JSON-loaded one by construction rather than by test coverage.
-Installation also rebuilds each preset's file path from the local data directory, so a
-shipped cache never carries the generating machine's paths.
+them and the currently loaded filament library, configs flattened onto the collection
+defaults, validated and registered — by the same function the JSON path calls straight
+after parsing a sub-file. The two paths share everything below the parse, which is what
+makes a cache-loaded bundle indistinguishable from a JSON-loaded one by construction
+rather than by test coverage. Installation also rebuilds each preset's file path from
+the local data directory, so a shipped cache never carries the generating machine's
+paths.

 App upgrades work because a cache normally survives one. Only a deliberate
 `CACHE_VERSION` bump makes an installed cache unreadable, and that is handled at
@@ -1,197 +0,0 @@
-# Prime tower sparse layers — High Level Design
-
-## Purpose and scope
-
-A prime tower exists to absorb filament changes, but it is planned on every
-object layer below the topmost change, not only on the layers that purge. The
-layers in between carry no filament change and print nothing but a block of the
-tower's own footprint to keep its top level. They are called sparse layers, and
-on a print with few changes they are most of the tower: they cost time, filament
-and a travel to the tower on every layer.
-
-Two settings trade that cost against something else. `wipe_tower_no_sparse_layers`
-drops them, which sinks the tower below the model. `wipe_tower_sparse_layers_combination`
-merges runs of them into fewer, thicker layers, which keeps the tower level with
-the model. Both are off by default, and with both off the tower prints one layer
-per object layer as it always has.
-
-The decisions belong to tower planning and G-code emission. They do not change
-sliced object geometry, but they do change the emitted G-code, the filament and
-time estimates, and — for the compacted case — whether a plate is printable at
-all. Changing either setting invalidates the tower step.
-
-## What a sparse layer is
-
-`ToolOrdering::fill_wipe_tower_partitions` counts the filament changes per layer
-and propagates that count downwards, so every layer below the topmost change is
-marked as carrying a tower. It then fills any gap between two tower layers, so
-the tower is continuous from the bed to its last purge. `wipe_tower_layer_height`
-is the distance from the previous tower layer, which is the object's layer height
-whenever the tower prints on every layer.
-
-`Print::_make_wipe_tower` plans one tower layer per such object layer. A layer
-whose only call keeps the current filament leaves no toolchange in the plan, and
-the layer it generates is a single result whose initial and new tool are equal.
-That is what `wipe_tower_layer_is_sparse` recognises, and it is the unit both
-settings work on.
-
-The plan stays one entry per tower layer in every case. The G-code emitter walks
-`WipeTowerData::tool_changes` by layer index, advancing once per object layer
-that carries a tower, so a planner that removed entries would silently shift
-every later layer onto the wrong tower geometry. Layers that print nothing are
-therefore still planned and still generated; they are marked, and the emitter
-drops them.
-
-## Shared rules
-
-Tower planning, G-code emission and the plate validation all have to agree about
-which layers print and where. They ask one set of free functions, declared beside
-the tower classes, rather than each re-deriving the answer from the raw options:
-
- `wipe_tower_sparse_layers_skipped` — whether sparse layers are really dropped.
-  Smooth timelapse and clumping detection park the nozzle on the tower every
-  layer, so with either of them on no layer is ever dropped and the option reads
-  as off everywhere.
- `wipe_tower_sparse_layers_combined` — whether runs are really merged. The same
-  two rule it out, and so does `wipe_tower_no_sparse_layers`: dropping the layers
-  outright is the stronger answer to the same problem, so the two settings are
-  exclusive and the GUI greys out the second while the first is on.
- `wipe_tower_layer_is_sparse`, `wipe_tower_layer_is_combined_away` — per-layer
-  questions the emitter asks about generated results.
- `compute_compacted_wipe_tower_z` — the tower's print z per planned layer when
-  it is compacted.
- `combine_sparse_wipe_tower_layers` and its `combine_sparse_wipe_tower_plan`
-  wrapper — the merge rule, applied to either generator's plan.
-
-Both tower generators are driven through these. `WipeTower` (Type 1, the block
-tower) and `WipeTower2` (Type 2, the default) keep separate plans with the same
-per-layer shape — print z, layer height, toolchanges, and a `combined_away` flag
-— so one template covers both.
-
-## Dropping sparse layers
-
-With `wipe_tower_no_sparse_layers`, the tower only grows on layers that carry a
-real change. It therefore falls one layer height behind the object for every
-sparse layer, and by the top of a tall print it can sit far below the model. The
-nozzle has to reach down to it at each purge.
-
-`compute_compacted_wipe_tower_z` derives that z once, from the generated results,
-so the emitter and the validator cannot disagree. Emission descends to it, but
-only once the nozzle is parked over the tower: descending while still over the
-model would drive the nozzle into the print, so a descent that would do that is
-deferred until after the travel to the tower. Extrusions emitted without an
-explicit z — the nozzle-change wipe in particular — are pulled down to the
-compacted z for the same reason.
-
-Reaching down is only safe if nothing tall stands near the tower. `Print.hpp`
-carries the clearance rule: a keep-out zone grown from the tower's footprint by
-the spiral z-hop envelope, and a per-object limit on how high an object may rise
-near it, tiered by the nozzle cone, the head body, the rod and the lid. The same
-rule serves the precise check on real extrusions, the pre-slice estimate that
-feeds the plater, and the outlines the plater draws while an object is dragged,
-so that the ring the user sees touches the object's outline exactly when the
-check trips.
-
-## Merging sparse layers
-
-With `wipe_tower_sparse_layers_combination`, no layer is dropped and nothing is
-compacted: the tower keeps following the object, and the nozzle never descends.
-Instead a run of consecutive sparse layers prints once, on the run's last layer,
-at the accumulated height of everything it covers — the same way infill
-combination merges sparse infill. The layers below it in the run print nothing.
-
-`combine_sparse_wipe_tower_plan` runs before the tower's depths are planned,
-because the heights it rewrites feed the extrusion flow of every later pass. It
-raises `height` in place on the layer that prints a run and sets `combined_away`
-on the rest; generation then proceeds unchanged, and the flag is copied onto the
-results so the emitter can drop them.
-
-Four constraints shape the rule:
-
- **Whole layers only.** A tower layer is entered at the object's z, so a merged
-  layer has to end on an object layer boundary. The merged height is therefore a
-  sum of whole layer heights, never a clamped value.
- **The nozzle's maximum layer height.** A run stops growing as soon as one more
-  layer would pass `max_layer_height` for the nozzle printing it — three quarters
-  of the nozzle diameter when that is left at 0, as elsewhere in slicing. The cap
-  is read through the filament-to-nozzle map, since `max_layer_height` is per
-  nozzle while the tower indexes filaments. This is what makes the setting inert
-  at common layer heights: two 0.2 mm layers are 0.4 mm and do not fit under a
-  0.3 mm maximum, so nothing merges until the layer height is 0.15 mm or below,
-  or the maximum is raised.
- **A filament change purges at its own z.** A layer with a real change can
-  neither be merged away nor absorb the run below it, so a run always ends on its
-  own last sparse layer and the change above it is untouched.
- **The first layer stays on the bed.** It carries the brim and is never merged.
-
-A run holds one filament throughout — that is what makes it sparse — so the cap
-is uniform across it, and the tower reserves depth only for the purges above a
-layer, so a run has one footprint and the merged layer covers exactly the area
-the layers it replaces would have.
-
-## Emission and accounting
-
-`WipeTowerIntegration` drops a layer whose results are marked, for both settings,
-through the same `ignore_sparse` path in `tool_change` and
-`is_empty_wipe_tower_gcode`. A dropped layer emits no travel to the tower and no
-extrusion.
-
-Filament used is accumulated by the generators while they write, so a layer that
-will be dropped must not be charged. Type 1 asks `layer_is_printed` at each of
-its accumulation points; Type 2 guards the equivalent block in `finish_layer`,
-which also stops a merged-away layer from adding height of its own — the layer
-that prints the run carries all of it.
-
-A merged layer is the only case where the tower's layer height differs from the
-object layer it sits on, and therefore the only case where the height the
-exporter already emitted for that layer is wrong for the tower. Both generators
-do declare a height, but each hardcodes a tag dialect — the block tower forces
-the BBL tag, the other writes the compatible one — while the G-code processor
-reads only the tag its printer uses. On a non-BBL printer with a Type 1 tower the
-declaration is dropped, and the merged layer is drawn and costed as a thin one.
-`WipeTowerIntegration::tower_height_tag` therefore declares it at export time,
-where the printer is known, and only when the tower's own G-code does not already
-carry the tag that will be read. The object's height returns on the next object
-path, because emission forces the processor role to the tower on any layer that
-carries one.
-
-## Constraints
-
-A layer that prints nothing prints nothing at all, including any interface work
-the tower planner scheduled there. The Type 1 block planner marks a layer as a
-contact layer when a filament category stops or starts being used relative to the
-layer below, and a sparse layer immediately above a change qualifies. Merging a
-run, like dropping its layers, replaces that interface with the run's single
-layer. Both settings are off by default for this among other reasons.
-
-Neither setting changes what the tower is for. A plate that needs a tower on
-every layer — smooth timelapse, clumping detection — gets one, and the settings
-read as off rather than compacting or merging in one place and not another.
-
-## Implementation and verification
-
- [WipeTower.hpp](../../src/libslic3r/GCode/WipeTower.hpp) declares the shared
-  rules and the plan-merging template;
-  [WipeTower.cpp](../../src/libslic3r/GCode/WipeTower.cpp) implements them and
-  the Type 1 tower, [WipeTower2.cpp](../../src/libslic3r/GCode/WipeTower2.cpp)
-  the Type 2 tower.
- [ToolOrdering.cpp](../../src/libslic3r/GCode/ToolOrdering.cpp) decides which
-  layers carry a tower at all, and
-  [Print.cpp](../../src/libslic3r/Print.cpp) plans it and runs the clearance
-  check whose rule lives in [Print.hpp](../../src/libslic3r/Print.hpp).
- [GCode.cpp](../../src/libslic3r/GCode.cpp) emits the tower, drops the layers
-  that print nothing, and declares a merged layer's height;
-  [PrintConfig.cpp](../../src/libslic3r/PrintConfig.cpp) defines the settings and
-  [ConfigManipulation.cpp](../../src/slic3r/GUI/ConfigManipulation.cpp) their
-  mutual exclusion.
- [GLCanvas3D.cpp](../../src/slic3r/GUI/GLCanvas3D.cpp) and
-  [PartPlate.cpp](../../src/slic3r/GUI/PartPlate.cpp) draw the compacted tower's
-  keep-out outlines live while the user drags.
- [Rule tests](../../tests/libslic3r/test_wipe_tower.cpp) cover the gating of
-  both settings, the per-layer predicates, the compacted z, the merge rule's run
-  flushing, height conservation, the nozzle cap and the first-layer exemption,
-  and the clearance geometry the plater draws.
- [Slicing tests](../../tests/fff_print/test_wipe_tower.cpp) slice a real print
-  and check that a run folds, that the tower still covers the object exactly
-  once, that a run too thin for the cap is left alone, and that a merged layer
-  declares its height in the tag the printer's processor reads.
@@ -1,240 +0,0 @@
-# Printer agents
-
-Printer agents isolate printer-specific communication from the rest of OrcaSlicer. The GUI and
-`DeviceManager` operate on a shared set of printer operations and device state; a selected printer
-agent implements those operations for a particular printer ecosystem. The agent boundary allows
-Bambu, Moonraker-based printers, built-in integrations, and Python-provided integrations to use the
-same application workflow without making the GUI understand every printer protocol.
-
-The current boundary is an adapter boundary around the existing application contract. In particular,
-some request fields and message payloads still use the Bambu-shaped representation that existing
-`MachineObject` and `DeviceManager` code consumes. The printer agent is responsible for translating
-that representation into the protocol spoken by its printer. This is an intentional compatibility
-constraint of the current design; the interface is not yet a neutral printer protocol.
-
-The v1 dialect migration path is deliberately narrow. `DeviceManager` currently speaks the Bambu JSON
-dialect because that is the payload shape already used throughout the command and state workflow. The
-v1 `OrcaPrinterAgent` also accepts that Bambu dialect. Its transport path places the small translation
-needed for the target printer at `deliver_to_sink`, keeping the compatibility code at the edge rather
-than spreading it through `DeviceManager` or the agent interface.
-
-The eventual direction is for `DeviceManager` to produce an Orca JSON dialect. The Bambu agent will then
-own the translation from Orca JSON to Bambu's protocol, while `OrcaPrinterAgent` can forward the Orca
-payload directly to its sink. The v1 translation at `deliver_to_sink` can then be removed without
-changing `DeviceManager`, the command callers, or the rest of the agent workflow.
-
-## Components
-
-The system has four relevant layers:
-
-```text
-GUI / DeviceManager / MachineObject
-              |
-        NetworkAgent
-          /       \
- IPrinterAgent   ICloudServiceAgent
-      |                 |
- printer protocol   authentication and cloud services
-```
-
-### `DeviceManager` and `MachineObject`
-
-`DeviceManager` owns the application-facing printer workflow. It maintains `MachineObject` instances,
-updates their state, filters devices for the active printer agent, and initiates operations such as
-homing, temperature changes, printing, subscriptions, and camera playback.
-
-`MachineObject` remains the shared state model used by the GUI. It does not contain the implementation
-of a printer protocol. When a device is discovered or returned by a cloud query, the device is tagged
-with the active `printer_agent_id`. Device lists and selected-machine operations use that tag to avoid
-sending an operation through an agent that does not own the device.
-
-### `NetworkAgent`
-
-`NetworkAgent` is the façade used by the GUI and `DeviceManager`. It owns:
-
- the currently selected `IPrinterAgent`;
- the registered cloud-service instances, indexed by provider;
- callbacks shared by the active printer agent and the application;
- the forwarding methods for printer commands and cloud operations.
-
-There is one active printer agent for the currently selected printer preset. Switching the preset
-increments the machine-list generation, disconnects the old printer agent, removes its callbacks, and
-installs the newly selected agent. The façade then forwards printer operations to that agent.
-
-Cloud operations are selected separately using a provider key. `NetworkAgent` forwards a cloud request
-to the matching `ICloudServiceAgent`, and forwards cloud camera operations with a device ID. The
-printer agent receives a cloud-agent pointer through `set_cloud_agent()` when it is created, allowing
-printer communication to obtain cloud tokens without depending on a concrete cloud implementation.
-
-### `IPrinterAgent`
-
-`IPrinterAgent` is the printer-facing contract. It covers:
-
- cloud-relay and direct-LAN message delivery;
- LAN connection, discovery, binding, and certificates;
- printer subscriptions and callbacks;
- print operations;
- filament synchronization;
- camera capability and local camera URL reporting;
- printer command methods.
-
-Concrete built-in implementations include the Bambu wrapper, the native Orca/Moonraker path, and
-other printer-agent implementations registered by the application. A printer agent may use either
-the cloud agent, a direct LAN connection, or both.
-
-### `ICloudServiceAgent`
-
-`ICloudServiceAgent` owns authentication and services provided by a cloud backend. It covers login
-state, tokens, user and printer lists, settings synchronization, model services, cloud messages, and
-cloud camera operations.
-
-Cloud camera operations are device-scoped:
-
- `get_camera_url(dev_id, callback)` obtains a stream URL for one device;
- `create_camera_signaling_channel(dev_id)` creates signaling for one device where the provider
-  supports it.
-
-This is separate from the local camera URL exposed by `IPrinterAgent`, which is currently scoped to
-the active printer agent because a normal LAN agent represents one physical printer connection.
-
-## Agent registration and selection
-
-`NetworkAgentFactory` maintains the printer-agent registry. Each registry entry contains an agent ID,
-a display name, and a factory function. Built-in agents register during application initialization.
-Python printer-agent capabilities register dynamically and contribute an agent ID and factory entry.
-
-The selected printer preset contains the printer-agent choice. If no explicit choice is stored, the
-application preserves the existing default behavior: Bambu presets select the Bambu agent and other
-presets select the native Orca agent. When a preset is changed, `GUI_App` resolves the effective agent
-ID, obtains the corresponding cloud agent, creates the printer agent through the registry, and installs
-it in `NetworkAgent`.
-
-The registry rejects conflicting agent IDs. This matters for Python plugins because an agent ID is the
-stable identity used by presets and device ownership; two enabled plugin capabilities must not claim
-the same ID.
-
-## Message and command flow
-
-There are two low-level message paths:
-
- `send_message()` publishes a command through the printer's cloud relay;
- `send_message_to_printer()` sends a command directly to the printer over the LAN path.
-
-Both paths accept a JSON string, quality-of-service and flag values, and return the existing network
-status code domain. The agent owns the conversion from that JSON contract to its native transport.
-
-The typed `command_*` methods are the application-facing convenience layer. The five generic defaults
-currently implemented by `IPrinterAgent` construct the existing JSON dialect and route through the
-same message path:
-
-| Method | Default operation |
-| --- | --- |
-| `command_xyz_abs()` | Send `G90` for absolute positioning |
-| `command_auto_leveling()` | Send `G29` for bed leveling |
-| `command_go_home()` | Use the supported homing operation or send `G28` |
-| `command_set_bed()` | Use the supported bed control or send `M140` |
-| `command_set_nozzle()` | Send `M104` for nozzle temperature |
-
-These are compatibility defaults for common printer workflows, not a guarantee that every firmware
-implements every command identically. An agent can override a method when its protocol needs another
-operation. For example, a Klipper configuration may use `BED_MESH_CALIBRATE` instead of `G29`.
-
-The remaining common command methods default to `ORCA_NETWORK_ERR_CMD_NOT_SUPPORTED` because their
-existing behavior is vendor-specific or has no portable implementation:
-
- AMS RFID refresh;
- AMS calibration;
- AMS tray selection;
- camera start;
- axis control.
-
-The methods remain on the common interface so an agent that supports them can override them explicitly.
-`sequence_id` remains part of the command contract because `DeviceManager` creates and tracks it as
-the command ID.
-
-## Device ownership and stale responses
-
-Printer-agent ownership is represented by `printer_agent_id` on device records and `MachineObject`
-instances. The active agent ID is attached when a device is discovered, returned by a cloud list, or
-reused after a preset switch. Local-machine configuration also persists the agent ID so a saved LAN
-device is not silently reused by an unrelated agent.
-
-Cloud printer-list responses carry three pieces of request context added by `NetworkAgent`:
-
-```text
-provider   cloud provider used for the request
-agent_id   active printer agent when the request was made
-generation machine-list generation when the request was made
-```
-
-`DeviceManager` accepts the response only when those values still match the current provider, active
-agent, and generation. This prevents a slow response from the previous preset or provider from
-repopulating the current device list.
-
-The provider mapping is currently selected by `GUI_App`: the Bambu agent maps to the Bambu cloud
-provider and other agents map to the Orca cloud provider. The generation check protects that existing
-selection from races; it does not make cloud-provider ownership intrinsic to an agent. Cloud-printer
-ownership and the broader Orca cloud services are therefore still separate architectural concerns.
-
-## Python printer agents
-
-`PrinterAgentPluginCapability` implements `IPrinterAgent` directly. The live capability object is
-registered with `NetworkAgentFactory` and handed out as the printer agent when its agent ID is selected.
-The plugin receives the selected `ICloudServiceAgent` through `set_cloud_agent()` just like a built-in
-printer agent.
-
-Python plugins must implement the core communication and lifecycle methods required by the interface,
-including agent metadata, printer connection, discovery callbacks, and the two message-send methods.
-Methods that are meaningful only to a particular printer are optional overrides where the C++ base
-class provides a default.
-
-All ten `command_*` methods are available in the Python binding and in the trampoline. Their override
-status is intentionally optional:
-
- the five generic commands use the C++ default when Python does not override them;
- the five vendor-specific commands return `NOT_SUPPORTED` unless Python supplies an implementation;
- a Python implementation can replace either behavior for its own protocol.
-
-The Python camera binding exposes HTTP, HTTPS, RTSP, and HTTP-snapshot modes. WebRTC remains a
-built-in C++ camera mode, but is not exposed as a Python mode because the current Python capability
-does not provide the corresponding cloud signaling-channel contract.
-
-## Camera playback boundary
-
-The camera stream mode describes how a stream is obtained; it does not by itself define ownership of
-the wxWidgets view that renders it. `MediaPlayCtrl` selects and tears down the active backend, while
-the wx parent owns the child window or renderer. This is important because a web view, native media
-control, and frame-based/WebRTC renderer have different wx window-lifetime requirements.
-
-Cloud URL and signaling requests are routed through `NetworkAgent` to the cloud provider selected for
-the device. Local URL requests are routed to the active printer agent. The distinction keeps cloud
-account services device-scoped while preserving the current one-LAN-agent/one-printer model.
-
-## Compatibility constraints
-
-The printer-agent boundary intentionally preserves several existing application contracts:
-
- Bambu-shaped JSON is still the shared command representation;
- existing network status codes are reused, with Orca-specific unsupported/capability errors added
-  in the Orca-reserved range;
- `MachineObject` remains the shared device-state model;
- preset and local-machine data retain compatibility with the existing agent-selection behavior;
- Python plugins use the existing capability and pybind11 registration system.
-
-The agent abstraction is therefore responsible for containing vendor differences, not for pretending
-that all vendor protocols are identical. The planned Orca JSON dialect is the protocol-neutral command
-model for the `DeviceManager`/agent boundary. Once it is introduced, Bambu-specific translation remains
-inside the Bambu agent and the Orca agent's v1 sink adapter can be removed as a self-contained cleanup.
-
-## Main implementation locations
-
- [`IPrinterAgent`](../../src/slic3r/Utils/IPrinterAgent.hpp) — printer-agent contract and generic command defaults
- [`ICloudServiceAgent`](../../src/slic3r/Utils/ICloudServiceAgent.hpp) — cloud service and per-device
-  cloud camera contract
- [`NetworkAgent`](../../src/slic3r/Utils/NetworkAgent.hpp) — façade and dispatch between active agents
- [`NetworkAgentFactory`](../../src/slic3r/Utils/NetworkAgentFactory.hpp) — built-in and Python agent registry
- [`DeviceManager`](../../src/slic3r/GUI/DeviceCore/DevManager.cpp) — device ownership, filtering, and
-  stale-response checks
- [`PrinterAgentPluginCapability`](../../src/slic3r/plugin/pluginTypes/printerAgent/PrinterAgentPluginCapability.cpp)
-  — Python bindings
- [`MediaPlayCtrl`](../../src/slic3r/GUI/MediaPlayCtrl.cpp) — camera backend selection and playback lifecycle
@@ -8,7 +8,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: PACKAGE VERSION\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
 "Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
 "Language-Team: LANGUAGE <LL@li.org>\n"
@@ -6161,6 +6161,9 @@ msgstr ""
 msgid "Preferences"
 msgstr ""

+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr ""
@@ -6168,9 +6171,6 @@ msgstr ""
 msgid "View"
 msgstr ""

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr ""

@@ -8,7 +8,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-03-15 10:55+0100\n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6637,6 +6637,9 @@ msgstr "Mostrar el contorn al voltant de l'objecte seleccionat a l'escena 3D"
 msgid "Preferences"
 msgstr "Preferències"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6645,9 +6648,6 @@ msgstr "Edita"
 msgid "View"
 msgstr "Vista"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Paquet de perfils"
@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Jakub Hencl\n"
 "Language-Team: \n"
@@ -6602,6 +6602,9 @@ msgstr "Zobrazit obrys kolem vybraného objektu ve 3D scéně."
 msgid "Preferences"
 msgstr "Předvolby"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6610,9 +6613,6 @@ msgstr "Upravit"
 msgid "View"
 msgstr "Zobrazit"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Balík předvoleb"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Heiko Liebscher <hliebschergmail.com>\n"
 "Language-Team: \n"
@@ -6490,6 +6490,9 @@ msgstr "Kontur um das ausgewählte Objekt in der 3D-Szene anzeigen."
 msgid "Preferences"
 msgstr "Einstellungen"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6498,9 +6501,6 @@ msgstr "Bearbeiten"
 msgid "View"
 msgstr "Ansicht"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Vorlagen-Bundle"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-17 15:44-0300\n"
 "Last-Translator: Alexandre Folle de Menezes\n"
 "Language-Team: \n"
@@ -6157,6 +6157,9 @@ msgstr ""
 msgid "Preferences"
 msgstr ""

+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr ""
@@ -6164,9 +6167,6 @@ msgstr ""
 msgid "View"
 msgstr ""

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr ""

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Ian A. Bassi <>\n"
 "Language-Team: \n"
@@ -6346,6 +6346,9 @@ msgstr "Mostrar el contorno alrededor del objeto seleccionado en la escena 3D."
 msgid "Preferences"
 msgstr "Preferencias"

+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Edición"
@@ -6353,9 +6356,6 @@ msgstr "Edición"
 msgid "View"
 msgstr "Vista"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Paquete de perfiles"

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-20 13:33+0200\n"
 "Last-Translator: Manu Goiogana <mgoiogana@gmail.com>\n"
 "Language-Team: \n"
@@ -6392,6 +6392,9 @@ msgstr "Erakutsi hautatutako objektuaren inguruko ingerada 3D eszenan."
 msgid "Preferences"
 msgstr "Hobespenak"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6400,9 +6403,6 @@ msgstr "Editatu"
 msgid "View"
 msgstr "Bista"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Aurrezarpen-paketea"

@@ -6,7 +6,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: Guislain Cyril, Thomas Lété\n"
@@ -6439,6 +6439,9 @@ msgstr "Afficher le tracé contour de l’objet sélectionné dans la scène 3D.
 msgid "Preferences"
 msgstr "Préférences"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6447,9 +6450,6 @@ msgstr "Édition"
 msgid "View"
 msgstr "Affichage"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Paquet de préréglages"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "Language: hu\n"
 "MIME-Version: 1.0\n"
 "Content-Type: text/plain; charset=UTF-8\n"
@@ -6541,6 +6541,9 @@ msgstr "Körvonal megjelenítése a kijelölt objektum körül a 3D nézetben."
 msgid "Preferences"
 msgstr "Beállítások"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6549,9 +6552,6 @@ msgstr "Szerkesztés"
 msgid "View"
 msgstr "Nézet"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Beállításcsomag"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6543,6 +6543,9 @@ msgstr "Mostra il contorno attorno all'oggetto selezionato nella scena 3D."
 msgid "Preferences"
 msgstr "Preferenze"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6551,9 +6554,6 @@ msgstr "Modifica"
 msgid "View"
 msgstr "Vista"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Pacchetto profili"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -6553,6 +6553,9 @@ msgstr "3Dシーンで選択したオブジェクトの周りにアウトライ
 msgid "Preferences"
 msgstr "設定"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6561,9 +6564,6 @@ msgstr "編集"
 msgid "View"
 msgstr "表示"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "プリセットバンドル"
@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-06-02 17:12+0900\n"
 "Last-Translator: crwusiz <crwusiz@gmail.com>\n"
 "Language-Team: \n"
@@ -6566,6 +6566,9 @@ msgstr "3D 장면에서 선택한 객체 주변에 윤곽선 표시"
 msgid "Preferences"
 msgstr "기본 설정"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6574,9 +6577,6 @@ msgstr "편집"
 msgid "View"
 msgstr "시점"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "사전 설정 번들"
@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: \n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-02 14:13+0300\n"
 "Last-Translator: Gintaras Kučinskas <sharanchius@gmail.com>\n"
 "Language-Team: \n"
@@ -6528,6 +6528,9 @@ msgstr "Rodyti kontūrą aplink pasirinktą objektą 3D scenoje."
 msgid "Preferences"
 msgstr "Parinktys"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6536,9 +6539,6 @@ msgstr "Redaguoti"
 msgid "View"
 msgstr "Vaizdas"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Profilių rinkinys"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: \n"
 "Language-Team: \n"
@@ -7122,6 +7122,9 @@ msgstr "Toon een omtrek rond het geselecteerde object in de 3D-scène."
 msgid "Preferences"
 msgstr "Voorkeuren"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -7130,9 +7133,6 @@ msgstr "Bewerken"
 msgid "View"
 msgstr "Weergave"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Voorinstellingenbundel"
@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: OrcaSlicer 2.3.0-rc\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: \n"
 "Last-Translator: Krzysztof Morga <<tlumaczeniebs@gmail.com>>\n"
 "Language-Team: \n"
@@ -6689,6 +6689,9 @@ msgstr "Przełącza wyświetlanie konturu wokół zaznaczonego obiektu w scenie
 msgid "Preferences"
 msgstr "Preferencje"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6697,9 +6700,6 @@ msgstr "Edycja"
 msgid "View"
 msgstr "Widok"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Pakiet profili"
@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-26 11:14-0300\n"
 "Last-Translator: Alexandre Folle de Menezes\n"
 "Language-Team: Portuguese, Brazilian\n"
@@ -6363,6 +6363,9 @@ msgstr "Mostrar contorno ao redor do objeto selecionado na cena 3D."
 msgid "Preferences"
 msgstr "Preferências"

+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Editar"
@@ -6370,9 +6373,6 @@ msgstr "Editar"
 msgid "View"
 msgstr "Visualizar"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Pacote de Predefinições"

@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: OrcaSlicer V2.5.0\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-02-25 13:38+0300\n"
 "Last-Translator: Felix14_v2\n"
 "Language-Team: Felix14_v2 (ДС/ТГ: @felix14_v2, почта: aleks111001@list.ru), Andylg <andylg@yandex.ru>\n"
@@ -6597,6 +6597,9 @@ msgstr "Отображение контура вокруг выбранных м
 msgid "Preferences"
 msgstr "Настройки"

+msgid "Open speed dial"
+msgstr ""
+
 msgctxt "Menu"
 msgid "Edit"
 msgstr "Правка"
@@ -6604,9 +6607,6 @@ msgstr "Правка"
 msgid "View"
 msgstr "Вид"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Пакет профилей"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "Language: sv\n"
 "MIME-Version: 1.0\n"
 "Content-Type: text/plain; charset=UTF-8\n"
@@ -7205,6 +7205,9 @@ msgstr "Visa en kontur runt det markerade objektet i 3D-scenen."
 msgid "Preferences"
 msgstr "Inställningar"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -7213,9 +7216,6 @@ msgstr "Redigera"
 msgid "View"
 msgstr "Vy"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Förinställningspaket"
@@ -7,7 +7,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-19 13:40+0700\n"
 "Last-Translator: Icezaza\n"
 "Language-Team: Thai\n"
@@ -6520,6 +6520,9 @@ msgstr "แสดงเค้าร่างรอบๆ วัตถุที
 msgid "Preferences"
 msgstr "การตั้งค่า"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6528,9 +6531,6 @@ msgstr "แก้ไข"
 msgid "View"
 msgstr "มุมมอง"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "ชุดที่ตั้งไว้ล่วงหน้า"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-08-21 23:18+0300\n"
 "Last-Translator: GlauTech\n"
 "Language-Team: \n"
@@ -6588,6 +6588,9 @@ msgstr "3D sahnede seçilen nesnenin etrafındaki ana hatları göster."
 msgid "Preferences"
 msgstr "Tercihler"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6596,9 +6599,6 @@ msgstr "Düzen"
 msgid "View"
 msgstr "Görünüm"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Ön ayar paketi"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: orcaslicerua\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-07-17 16:25+0300\n"
 "Last-Translator: Andrij Mizyk <andm1zyk@proton.me>\n"
 "Language-Team: Ukrainian\n"
@@ -6557,6 +6557,9 @@ msgstr "Показувати контур навколо виділеного о
 msgid "Preferences"
 msgstr "Налаштування"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6565,9 +6568,6 @@ msgstr "Редагування"
 msgid "View"
 msgstr "Вигляд"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "Набір пресетів"

@@ -3,7 +3,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-10-02 17:43+0700\n"
 "Last-Translator: \n"
 "Language-Team: hainguyen.ts13@gmail.com\n"
@@ -6907,6 +6907,9 @@ msgstr "Hiện đường viền xung quanh vật thể đã chọn trong cảnh
 msgid "Preferences"
 msgstr "Tùy chọn"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6915,9 +6918,6 @@ msgstr "Chỉnh sửa"
 msgid "View"
 msgstr "Xem"

-msgid "Open Speed Dial"
-msgstr ""
-
 # AI Translated
 msgid "Preset Bundle"
 msgstr "Gói cài đặt sẵn"
@@ -6,7 +6,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Slic3rPE\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2026-06-11 12:37-0300\n"
 "Last-Translator: Handle <mail@bysb.net>\n"
 "Language-Team: \n"
@@ -6375,6 +6375,9 @@ msgstr "在3D场景中显示选中对象的轮廓"
 msgid "Preferences"
 msgstr "偏好设置"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6383,9 +6386,6 @@ msgstr "编辑"
 msgid "View"
 msgstr "视图"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "预设包"

@@ -9,7 +9,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2026-09-22 17:02+0800\n"
+"POT-Creation-Date: 2026-09-22 12:39+0800\n"
 "PO-Revision-Date: 2025-11-28 13:48-0600\n"
 "Last-Translator: tntchn <15895303+tntchn@users.noreply.github.com>\n"
 "Language-Team: \n"
@@ -6505,6 +6505,9 @@ msgstr "在 3D 場景中顯示選定物件的輪廓"
 msgid "Preferences"
 msgstr "偏好設定"

+msgid "Open speed dial"
+msgstr ""
+
 # AI Translated
 msgctxt "Menu"
 msgid "Edit"
@@ -6513,9 +6516,6 @@ msgstr "編輯"
 msgid "View"
 msgstr "視角"

-msgid "Open Speed Dial"
-msgstr ""
-
 msgid "Preset Bundle"
 msgstr "設定檔組"

@@ -6,7 +6,6 @@
 	"instantiation": "false",
 	"gcode_flavor": "marlin2",
 	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n",
-	"file_start_gcode": ";TIME:{print_time_sec}s",
 	"machine_start_gcode": "M4899 T3 ; Enable v3 jerk and S-curve acceleration \nM104 S150 ; Set hotend temp to 150 degrees to prevent ooze\nM190 S{first_layer_bed_temperature[0]} ; set and wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; set final nozzle temp to stabilize\nG28 ;Home\n;LAYER_COUNT:{total_layer_count}",
 	"machine_end_gcode": "M104 S0\nM140 S0\n;Retract the filament\nG92 E1\nG1 E-1 F300\nG28 X0 Y0\nM18",
 	"change_filament_gcode": "M600",
@@ -1,6 +1,6 @@
 {
 	"name": "Anycubic",
-	"version": "02.04.00.07",
+	"version": "02.04.00.05",
 	"force_update": "0",
 	"description": "Anycubic configurations",
 	"machine_model_list": [
@@ -48,10 +48,6 @@
 			"name": "Anycubic Kobra 3 Max",
 			"sub_path": "machine/Anycubic Kobra 3 Max.json"
 		},
-		{
-			"name": "Anycubic Kobra 3 V2",
-			"sub_path": "machine/Anycubic Kobra 3 V2.json"
-		},
 		{
 			"name": "Anycubic Kobra Max",
 			"sub_path": "machine/Anycubic Kobra Max.json"
@@ -106,10 +102,6 @@
 			"name": "0.08mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.08mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.08mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.08mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -126,10 +118,6 @@
 			"name": "0.10mm Detail @Anycubic Kobra 3 0.2 nozzle",
 			"sub_path": "process/0.10mm Detail @Anycubic Kobra 3 0.2 nozzle.json"
 		},
-		{
-			"name": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "process/0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
 		{
 			"name": "0.10mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.10mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -154,10 +142,6 @@
 			"name": "0.12mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.12mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.12mm Standard @Anycubic Kobra S1 Max 0.25 nozzle",
 			"sub_path": "process/0.12mm Standard @Anycubic Kobra S1 Max 0.25 nozzle.json"
@@ -230,10 +214,6 @@
 			"name": "0.16mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.16mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.16mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.16mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -306,10 +286,6 @@
 			"name": "0.20mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.20mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.20mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.20mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -366,10 +342,6 @@
 			"name": "0.24mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.24mm Standard @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "process/0.24mm Standard @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -398,10 +370,6 @@
 			"name": "0.28mm Standard @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "process/0.28mm Standard @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "0.28mm Standard @Anycubic Kobra Neo 0.4 nozzle",
 			"sub_path": "process/0.28mm Standard @Anycubic Kobra Neo 0.4 nozzle.json"
@@ -458,10 +426,6 @@
 			"name": "0.30mm Standard @Anycubic Kobra 3 Max 0.6 nozzle",
 			"sub_path": "process/0.30mm Standard @Anycubic Kobra 3 Max 0.6 nozzle.json"
 		},
-		{
-			"name": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
 		{
 			"name": "0.30mm Standard @Anycubic Kobra S1 Max 0.6 nozzle",
 			"sub_path": "process/0.30mm Standard @Anycubic Kobra S1 Max 0.6 nozzle.json"
@@ -490,10 +454,6 @@
 			"name": "0.40mm Standard @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "process/0.40mm Standard @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "0.40mm Standard @Anycubic Kobra S1 Max 0.8 nozzle",
 			"sub_path": "process/0.40mm Standard @Anycubic Kobra S1 Max 0.8 nozzle.json"
@@ -517,34 +477,6 @@
 		{
 			"name": "0.56mm Standard @Anycubic Kobra S1 Max 0.8 nozzle",
 			"sub_path": "process/0.56mm Standard @Anycubic Kobra S1 Max 0.8 nozzle.json"
-		},
-		{
-			"name": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "process/0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "process/0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "process/0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle.json"
 		}
 	],
 	"filament_list": [
@@ -596,10 +528,6 @@
 			"name": "Anycubic ABS @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic ABS @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic ABS @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic ABS @Anycubic Kobra S1 0.4 nozzle.json"
@@ -636,10 +564,6 @@
 			"name": "Anycubic ASA @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic ASA @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic ASA @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic ASA @Anycubic Kobra S1 0.4 nozzle.json"
@@ -780,10 +704,6 @@
 			"name": "Anycubic PETG @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PETG @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra S1 0.4 nozzle.json"
@@ -848,22 +768,6 @@
 			"name": "Anycubic PLA @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra S1 0.4 nozzle.json"
@@ -888,22 +792,6 @@
 			"name": "Anycubic PLA @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Glow @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Glow @Anycubic Kobra X 0.4 nozzle.json"
@@ -912,10 +800,6 @@
 			"name": "Anycubic PLA High Speed @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA High Speed @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA High Speed @Anycubic Kobra S1 0.4 nozzle.json"
@@ -940,26 +824,10 @@
 			"name": "Anycubic PLA Luminous @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Luminous @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Matte @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Matte @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -976,30 +844,10 @@
 			"name": "Anycubic PLA Matte @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Matte @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Silk @Anycubic Kobra 3 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 Max 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Silk @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra S1 0.4 nozzle.json"
@@ -1020,10 +868,6 @@
 			"name": "Anycubic PLA Silk @Anycubic Kobra X 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra X 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA Translucent @Anycubic Kobra S1 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA Translucent @Anycubic Kobra S1 Max 0.4 nozzle.json"
@@ -1136,10 +980,6 @@
 			"name": "Anycubic TPU @Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "filament/Anycubic TPU @Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "filament/Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
 		{
 			"name": "Anycubic TPU @Anycubic Kobra S1 0.4 nozzle",
 			"sub_path": "filament/Anycubic TPU @Anycubic Kobra S1 0.4 nozzle.json"
@@ -1176,22 +1016,6 @@
 			"name": "Anycubic PETG @Anycubic Kobra 3 0.4 nozzle",
 			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 0.4 nozzle.json"
 		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
-		{
-			"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "filament/Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic PLA @Anycubic Kobra 2 Max 0.4 nozzle",
 			"sub_path": "filament/Anycubic PLA @Anycubic Kobra 2 Max 0.4 nozzle.json"
@@ -1350,22 +1174,6 @@
 			"name": "Anycubic Kobra 3 Max 0.8 nozzle",
 			"sub_path": "machine/Anycubic Kobra 3 Max 0.8 nozzle.json"
 		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.2 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.2 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.4 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.4 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.6 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.6 nozzle.json"
-		},
-		{
-			"name": "Anycubic Kobra 3 V2 0.8 nozzle",
-			"sub_path": "machine/Anycubic Kobra 3 V2 0.8 nozzle.json"
-		},
 		{
 			"name": "Anycubic Kobra Max 0.4 nozzle",
 			"sub_path": "machine/Anycubic Kobra Max 0.4 nozzle.json"
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_abs",
-	"from": "system",
-	"setting_id": "LXkKhWH9YcYPr3IT",
-	"filament_id": "OF223rZv",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic ABS @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"ABS"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"5"
-	],
-	"nozzle_temperature": [
-		"250"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"15"
-	],
-	"fan_min_speed": [
-		"1"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.05"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"70%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"100"
-	],
-	"hot_plate_temp": [
-		"90"
-	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
-	"nozzle_temperature_initial_layer": [
-		"250"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"15"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"16"
-	],
-	"slow_down_min_speed": [
-		"25"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"90"
-	],
-	"textured_plate_temp_initial_layer": [
-		"90"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_asa",
-	"from": "system",
-	"setting_id": "cWBQa7XzDl3czIOs",
-	"filament_id": "OF0yFLkY",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic ASA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"ASA"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"270"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"15"
-	],
-	"fan_min_speed": [
-		"1"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"30"
-	],
-	"filament_density": [
-		"1.04"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"70%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"100"
-	],
-	"hot_plate_temp": [
-		"100"
-	],
-	"hot_plate_temp_initial_layer": [
-		"100"
-	],
-	"nozzle_temperature_initial_layer": [
-		"270"
-	],
-	"nozzle_temperature_range_high": [
-		"280"
-	],
-	"nozzle_temperature_range_low": [
-		"240"
-	],
-	"overhang_fan_speed": [
-		"15"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"16"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"110"
-	],
-	"textured_plate_temp": [
-		"100"
-	],
-	"textured_plate_temp_initial_layer": [
-		"100"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pet",
-	"from": "system",
-	"setting_id": "suyxKj9qKLtpBhhU",
-	"filament_id": "OFo6n2pB",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PETG @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PETG"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"8"
-	],
-	"nozzle_temperature": [
-		"230"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"5"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"20"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"15"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.23"
-	],
-	"filament_deretraction_speed": [
-		"80"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"80%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"6"
-	],
-	"hot_plate_temp": [
-		"70"
-	],
-	"hot_plate_temp_initial_layer": [
-		"70"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"90"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"25"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"70"
-	],
-	"textured_plate_temp_initial_layer": [
-		"70"
-	]
-}
@@ -1,42 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "OOOjWFMFhP1fMhFf",
-	"filament_id": "OFo6n2pB",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PETG @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PETG"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"hot_plate_temp": [
-		"70"
-	],
-	"hot_plate_temp_initial_layer": [
-		"70"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "uJRZr6orTVm79FeE",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"1.6"
-	],
-	"nozzle_temperature": [
-		"230"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "udLvkeYZ9Av7GkDz",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "W69H1Vca3f74FfYj",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "TR27JCwXxHeVhVHN",
-	"filament_id": "OFmjN2bc",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.6"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "i0FTxiH68CKHiLLT",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,258 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "XHa1HSjh0RjAo0nz",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_layer_time_BRASS": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,261 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "iRVPFxNMEfkCDnMh",
-	"filament_id": "OF80Qbpq",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Galaxy @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_max_speed_BRASS": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"fan_min_speed_BRASS": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "itTckVFabfsVbNBK",
-	"filament_id": "OF5PtjTp",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Glow @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"0"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"40"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"0%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"2"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"2"
-	],
-	"filament_z_hop": [
-		"0.4"
-	],
-	"filament_z_hop_types": [
-		"Auto Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"9"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "YLxoiuRDXBWLQYw4",
-	"filament_id": "OFjVOWfJ",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA High Speed @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"18"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"nil"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"2"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"210"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"7"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "JwcCfY4XVCRJaDeS",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"nil"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "Sjw7irNgwCZMfWS3",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"50"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "HeQwxU4T2W1V0LM3",
-	"filament_id": "OFCSyK66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Marble @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"210"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "H3PIqeTzjvtFQXYv",
-	"filament_id": "OFIE3vOf",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Matte @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.98"
-	],
-	"filament_max_volumetric_speed": [
-		"9"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"0"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "4zmGMIi6jHJhU4c6",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.97"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"100"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "wLkJ1CJgdWnT4NoJ",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.94"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"50"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "kkcDxmDe6F9fwhoJ",
-	"filament_id": "OF5F0S66",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Metal @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"Slope Lift"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"215"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.035"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "QRl3zpmacQ8D8aNX",
-	"filament_id": "OFCp3Bgo",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA SE @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.97"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.8"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"14"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "qF5SGZKoINokZfx2",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"nil"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"0.5"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"30"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"65"
-	],
-	"textured_plate_temp_initial_layer": [
-		"65"
-	]
-}
@@ -1,51 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "6aUrszW2Dj8CNYIp",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_speed": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"pressure_advance": [
-		"0.025"
-	],
-	"slow_down_layer_time": [
-		"10"
-	]
-}
@@ -1,51 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "f8K19ebfxiXji84y",
-	"filament_id": "OFFwJWea",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Silk @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"7.2"
-	],
-	"nozzle_temperature": [
-		"220"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_speed": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"65"
-	],
-	"hot_plate_temp_initial_layer": [
-		"65"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"pressure_advance": [
-		"0.025"
-	]
-}
@@ -1,273 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_pla",
-	"from": "system",
-	"setting_id": "NTs7c6NqAudTl9wk",
-	"filament_id": "OF7c9fln",
-	"instantiation": "true",
-	"filament_settings_id": [
-		"Anycubic PLA Translucent @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_flow_ratio": [
-		"0.96"
-	],
-	"filament_max_volumetric_speed": [
-		"12"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"dont_slow_down_outer_wall": [
-		"1"
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"80"
-	],
-	"fan_cooling_layer_time_BRASS": [
-		"100"
-	],
-	"fan_max_speed": [
-		"80"
-	],
-	"fan_max_speed_BRASS": [
-		"100"
-	],
-	"fan_min_speed": [
-		"60"
-	],
-	"fan_min_speed_BRASS": [
-		"70"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"20"
-	],
-	"filament_density": [
-		"1.24"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"nil"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"nil"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"1.2"
-	],
-	"filament_retraction_minimum_travel": [
-		"nil"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"nil"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"0"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"nozzle_temperature_BRASS": [
-		"205"
-	],
-	"nozzle_temperature_initial_layer": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"50%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"0"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_layer_time_BRASS": [
-		"10"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "filament",
-	"name": "Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_filament_tpu",
-	"from": "system",
-	"setting_id": "oSWtTJpng3ERixPJ",
-	"filament_id": "OFMsDGbs",
-	"instantiation": "true",
-	"filament_vendor": [
-		"Anycubic"
-	],
-	"filament_settings_id": [
-		"Anycubic TPU @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"TPU"
-	],
-	"filament_flow_ratio": [
-		"1"
-	],
-	"filament_max_volumetric_speed": [
-		"3.2"
-	],
-	"nozzle_temperature": [
-		"210"
-	],
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"activate_air_filtration": [
-		"0"
-	],
-	"activate_chamber_temp_control": [
-		"0"
-	],
-	"additional_cooling_fan_speed": [
-		"0"
-	],
-	"bed_type": [
-		"High Temp Plate"
-	],
-	"chamber_temperature": [
-		"0"
-	],
-	"close_fan_the_first_x_layers": [
-		"1"
-	],
-	"compatible_printers_condition": "",
-	"compatible_prints": [],
-	"compatible_prints_condition": "",
-	"complete_print_exhaust_fan_speed": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"35"
-	],
-	"cool_plate_temp_initial_layer": [
-		"35"
-	],
-	"default_filament_colour": [
-		""
-	],
-	"during_print_exhaust_fan_speed": [
-		"60"
-	],
-	"enable_overhang_bridge_fan": [
-		"1"
-	],
-	"enable_pressure_advance": [
-		"0"
-	],
-	"eng_plate_temp": [
-		"0"
-	],
-	"eng_plate_temp_initial_layer": [
-		"0"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"fan_max_speed": [
-		"100"
-	],
-	"fan_min_speed": [
-		"80"
-	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
-	"filament_cost": [
-		"0"
-	],
-	"filament_density": [
-		"1.23"
-	],
-	"filament_deretraction_speed": [
-		"25"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_end_gcode": [
-		"; filament end gcode\n"
-	],
-	"filament_is_support": [
-		"0"
-	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
-	"filament_long_retractions_when_cut": [
-		"nil"
-	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"15"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"0"
-	],
-	"filament_multitool_ramming_volume": [
-		"0"
-	],
-	"filament_notes": [
-		""
-	],
-	"filament_ramming_parameters": [
-		"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-	],
-	"filament_retract_before_wipe": [
-		"0%"
-	],
-	"filament_retract_lift_above": [
-		"nil"
-	],
-	"filament_retract_lift_below": [
-		"nil"
-	],
-	"filament_retract_lift_enforce": [
-		"nil"
-	],
-	"filament_retract_restart_extra": [
-		"nil"
-	],
-	"filament_retract_when_changing_layer": [
-		"1"
-	],
-	"filament_retraction_distances_when_cut": [
-		"nil"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_minimum_travel": [
-		"1"
-	],
-	"filament_retraction_speed": [
-		"35"
-	],
-	"filament_shrink": [
-		"100%"
-	],
-	"filament_soluble": [
-		"0"
-	],
-	"filament_start_gcode": [
-		"; filament start gcode"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
-	"filament_wipe": [
-		"1"
-	],
-	"filament_wipe_distance": [
-		"nil"
-	],
-	"filament_z_hop": [
-		"nil"
-	],
-	"filament_z_hop_types": [
-		"nil"
-	],
-	"full_fan_speed_layer": [
-		"3"
-	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
-	"nozzle_temperature_initial_layer": [
-		"230"
-	],
-	"nozzle_temperature_range_high": [
-		"230"
-	],
-	"nozzle_temperature_range_low": [
-		"190"
-	],
-	"overhang_fan_speed": [
-		"100"
-	],
-	"overhang_fan_threshold": [
-		"95%"
-	],
-	"pressure_advance": [
-		"0.05"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"required_nozzle_HRC": [
-		"0"
-	],
-	"slow_down_for_layer_cooling": [
-		"1"
-	],
-	"slow_down_layer_time": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"support_material_interface_fan_speed": [
-		"-1"
-	],
-	"temperature_vitrification": [
-		"60"
-	],
-	"textured_plate_temp": [
-		"60"
-	],
-	"textured_plate_temp_initial_layer": [
-		"60"
-	]
-}
@@ -1,255 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "gaQ37xRo6J467j1y",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.2 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.2",
-	"nozzle_diameter": [
-		"0.2"
-	],
-	"default_print_profile": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": [
-		"230x110"
-	],
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": [
-		"512x512/PNG/top"
-	],
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"40"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "G92 E0\nG1 E-2 F3600\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F900 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.14"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0.3"
-	],
-	"retract_lift_below": [
-		"258"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"0"
-	],
-	"retraction_speed": [
-		"40"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"1"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}
@@ -1,251 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "l49qdfdrHYEO04bV",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.4 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.4",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"default_print_profile": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": "230x110/PNG",
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": "512x512/PNG/top",
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"60"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400\nG92 E0 ; zero the extruder\nG1 E-2 F3600\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F900 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.28"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"259"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"1"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"60"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "0",
-	"support_chamber_temp_control": "0",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Slope Lift"
-	],
-	"z_offset": "0"
-}
@@ -1,251 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "hQQgQT5HeCVGpBAL",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.6 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.6",
-	"nozzle_diameter": [
-		"0.6"
-	],
-	"default_print_profile": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": "230x110/PNG",
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": "512x512/PNG/top",
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"30"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400 ; wait for buffer to clear\nG92 E0 ; zero the extruder\nG1 E-1 F3600 ; retract\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F600 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.05\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.42"
-	],
-	"min_layer_height": [
-		"0.12"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"259"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"30"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}
@@ -1,255 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"setting_id": "LBhbohm7o4jW6OYw",
-	"instantiation": "true",
-	"printer_technology": "FFF",
-	"printer_settings_id": "Anycubic Kobra 3 V2 0.8 nozzle",
-	"printer_model": "Anycubic Kobra 3 V2",
-	"printer_variant": "0.8",
-	"nozzle_diameter": [
-		"0.8"
-	],
-	"default_print_profile": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"default_filament_profile": [
-		"Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"disable_m73": "0",
-	"gcode_flavor": "klipper",
-	"printable_area": [
-		"0x0",
-		"255x0",
-		"255x255",
-		"0x255"
-	],
-	"printable_height": "260",
-	"thumbnails": [
-		"230x110"
-	],
-	"thumbnails_format": "PNG",
-	"thumbnails_internal": [
-		"512x512/PNG/top"
-	],
-	"thumbnails_internal_switch": "1",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [],
-	"bed_mesh_max": "0,0",
-	"bed_mesh_min": "0,0",
-	"bed_mesh_probe_distance": "0,0",
-	"before_layer_change_gcode": "; BEFORE_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "; FLUSH_START\n;;; M400 P0\nT[next_extruder] ; change extruder\n; 1\n;;; G1 E-2 F2400\n;;; G1 Z{max(toolchange_z+0.6, 5.0)} F600\n;;; G1 X271.5 F12000\n;;; G1 E-5 F600\n;;; G1 X278 F600\n;;; M400 P3530\n;;; G1 E-1 F600\n;;; G1 Z{max(toolchange_z+2.6, 7.0)}  F600\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P31050\n;;; M400 P17510\n; 2\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n;;; G1 X250 F1200\n;;; M400 P0\n;;; G1 X278 F18000\n;;; G1 X271.5 F1200\n;;; G1 E2 F300\n;;; M400 P0\n; 3.1\n;;; M106 S255\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.2\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n; 3.3\n;;; G1 X36 Y260 Z-0.8 F9600\n;;; G1 X50 Y260 Z1 F9600\n;;; G1 X86 Y260 Z1 F9600\n;;; G1 X90 Y260 Z-0.8 F9600\n;;; G1 X90 Y259 Z-0.8 F9600\n;;; G1 X86 Y259 Z1 F9600\n;;; G1 X50 Y259 Z1 F9600\n;;; G1 X36 Y259 Z-0.8 F9600\n;;; G1 Z{toolchange_z}\n;;; M400 P0\n; FLUSH_END",
-	"cooling_tube_length": "0",
-	"cooling_tube_retraction": "0",
-	"deretraction_speed": [
-		"0"
-	],
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "0",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "0",
-	"extruder_clearance_height_to_lid": "250",
-	"extruder_clearance_height_to_rod": "20",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"FF4D4F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": "; AFTER_LAYER_CHANGE [layer_num] @ [layer_z]mm",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M400 ; wait for buffer to clear\nG92 E0 ; zero the extruder\nG1 E-2 F3000 ; retract\n{if max_layer_z < max_print_height-1}G1 Z{max_layer_z+2} F600 ; Move print head further up{endif}\nG1 X250 Y220 F12000 ; present print\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107;turn off fan\nM84; disable motors\n; disable stepper motors\n\n",
-	"machine_load_filament_time": "42",
-	"machine_max_acceleration_e": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"1000",
-		"1000"
-	],
-	"machine_max_jerk_e": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_x": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_y": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_jerk_z": [
-		"20",
-		"20",
-		"20"
-	],
-	"machine_max_speed_e": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_x": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_y": [
-		"600",
-		"300",
-		"780"
-	],
-	"machine_max_speed_z": [
-		"15",
-		"10",
-		"26"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M600",
-	"machine_start_gcode": "G9111 bedTemp=[first_layer_bed_temperature] extruderTemp=[first_layer_temperature[initial_tool]]\nM117\nM900 K0.051\n; print_bed_min = {print_bed_min[0]},{print_bed_min[1]}\n; print_bed_max = {print_bed_max[0]},{print_bed_max[1]}\n; print_bed_size = {print_bed_size[0]},{print_bed_size[1]}\n; first_layer_print_min = {first_layer_print_min[0]},{first_layer_print_min[1]}\n; first_layer_print_max = {first_layer_print_max[0]},{first_layer_print_max[1]}\n; first_layer_print_size = {first_layer_print_size[0]},{first_layer_print_size[1]}",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.56"
-	],
-	"min_layer_height": [
-		"0.16"
-	],
-	"nozzle_height": "4",
-	"nozzle_hrc": "0",
-	"nozzle_type": "brass",
-	"nozzle_volume": "107",
-	"parking_pos_retraction": "0",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printer_flush_multiplier": "1",
-	"printer_notes": "",
-	"printer_structure": "i3",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"0"
-	],
-	"retract_lift_above": [
-		"0.3"
-	],
-	"retract_lift_below": [
-		"259.6"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_on_top_layer": [
-		"1"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"0"
-	],
-	"retraction_length": [
-		"1"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"40"
-	],
-	"scan_first_layer": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "1",
-	"template_custom_gcode": "",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Auto Lift"
-	],
-	"z_offset": "0"
-}
@@ -1,12 +0,0 @@
-{
-    "type": "machine_model",
-    "machine_tech": "FFF",
-    "family": "Anycubic",
-    "name": "Anycubic Kobra 3 V2",
-    "model_id": "Anycubic Kobra 3 V2",
-    "nozzle_diameter": "0.4;0.2;0.6;0.8",
-    "bed_model": "Anycubic Kobra 3 V2_buildplate_model.stl",
-    "bed_texture": "Anycubic Kobra 3 V2_buildplate_texture.svg",
-    "hotend_model": "",
-    "default_materials": "Anycubic PLA @Anycubic Kobra 3 V2 0.2 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.4 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.6 nozzle;Anycubic PLA @Anycubic Kobra 3 V2 0.8 nozzle"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "9yiDozcVDSxKkz4V",
-	"instantiation": "true",
-	"print_settings_id": "0.08mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.08",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "7",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "1",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "350",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "8%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "3",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "200",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "1",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "grid",
-	"sparse_infill_speed": "450",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.08",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "15",
-	"support_top_z_distance": "0.08",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "9",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "200",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "eSyZsnWMuOyokoLr",
-	"instantiation": "true",
-	"print_settings_id": "0.10mm Standard @Anycubic Kobra 3 V2 0.2 nozzle",
-	"layer_height": "0.1",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.2 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "5",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "50%",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "10",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.075",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "0",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "100",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.25",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.1",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "10",
-	"inner_wall_line_width": "0.22",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "100%",
-	"internal_solid_infill_line_width": "0.22",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "120",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.22",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "10",
-	"outer_wall_line_width": "0.22",
-	"outer_wall_speed": "80",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "100%",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "20",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "100%",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.22",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "150",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.1",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.5",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.22",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.1",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "7",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.22",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "120",
-	"travel_acceleration": "15000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "4",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,58 +0,0 @@
-{
-	"type": "process",
-	"name": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "HqXRokM0mAA691LV",
-	"instantiation": "true",
-	"print_settings_id": "0.12mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.12",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "2000",
-	"bridge_speed": "30",
-	"brim_type": "auto_brim",
-	"default_acceleration": "5000",
-	"default_jerk": "9",
-	"gap_infill_speed": "180",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"inner_wall_speed": "150",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_speed": "180",
-	"ironing_flow": "10%",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "60",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "35",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"small_perimeter_speed": "50%",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_speed": "180",
-	"support_interface_top_layers": "2",
-	"support_threshold_angle": "20",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_speed": "150",
-	"travel_acceleration": "5000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "NCKx6glFcaEOhqZC",
-	"instantiation": "true",
-	"print_settings_id": "0.12mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.12",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "5",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "350",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "300",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "430",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.12",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "20",
-	"support_top_z_distance": "0.12",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "5",
-	"top_shell_thickness": "0.6",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "200",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,51 +0,0 @@
-{
-	"type": "process",
-	"name": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "mVDCX89vYKfBA57g",
-	"instantiation": "true",
-	"print_settings_id": "0.16mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.16",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "2000",
-	"default_acceleration": "4000",
-	"default_jerk": "9",
-	"infill_anchor_max": "20",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"internal_solid_infill_acceleration": "4000",
-	"internal_solid_infill_speed": "200",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "150",
-	"overhang_1_4_speed": "60",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "30",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"small_perimeter_speed": "50%",
-	"sparse_infill_acceleration": "4000",
-	"sparse_infill_speed": "200",
-	"support_line_width": "0.42",
-	"support_threshold_angle": "25",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "4000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "ut3FZjM7h3doFjRg",
-	"instantiation": "true",
-	"print_settings_id": "0.16mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.16",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "4",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "60",
-	"overhang_2_4_speed": "30",
-	"overhang_3_4_speed": "10",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "300",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.16",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "25",
-	"support_top_z_distance": "0.16",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "6",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "150",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,57 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"from": "system",
-	"setting_id": "V7T6yBxuQzWucCpA",
-	"instantiation": "true",
-	"print_settings_id": "0.20mm High Quality @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.2",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"bottom_shell_thickness": "0",
-	"bridge_acceleration": "4000",
-	"bridge_speed": "50",
-	"brim_object_gap": "0.1",
-	"brim_width": "5",
-	"default_acceleration": "4000",
-	"default_jerk": "9",
-	"initial_layer_infill_speed": "50",
-	"initial_layer_speed": "50",
-	"inner_wall_acceleration": "4000",
-	"inner_wall_jerk": "9",
-	"inner_wall_speed": "150",
-	"internal_solid_infill_acceleration": "4000",
-	"internal_solid_infill_speed": "250",
-	"ironing_flow": "10%",
-	"outer_wall_acceleration": "2000",
-	"outer_wall_jerk": "9",
-	"outer_wall_speed": "60",
-	"overhang_4_4_speed": "10",
-	"prime_tower_width": "30",
-	"raft_first_layer_expansion": "5",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"seam_slope_conditional": "1",
-	"seam_slope_inner_walls": "1",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"sparse_infill_acceleration": "4000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "270",
-	"support_line_width": "0.42",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_speed": "200",
-	"travel_acceleration": "4000",
-	"travel_jerk": "9",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wipe_on_loops": "0",
-	"wipe_tower_extra_spacing": "120%"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "K5se4jnf2XHJNkEQ",
-	"instantiation": "true",
-	"print_settings_id": "0.20mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.2",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "250",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "130",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "130",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "300",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.4",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "30",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "0",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "5",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "130",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "cg8f6Q9o8nRePSC9",
-	"instantiation": "true",
-	"print_settings_id": "0.24mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.24",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "200",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.45",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "200",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "200",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "35",
-	"support_top_z_distance": "0.2",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "15%",
-	"top_shell_layers": "4",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "180",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,24 +0,0 @@
-{
-	"type": "process",
-	"name": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "DhqKrBJZh4W22xna",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.24mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.24",
-	"brim_type": "auto_brim",
-	"default_acceleration": "6000",
-	"default_jerk": "9",
-	"elefant_foot_compensation": "0.1",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"outer_wall_jerk": "9",
-	"raft_first_layer_expansion": "5",
-	"sparse_infill_acceleration": "6000",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "Qe8XQonRxfA8Jei1",
-	"instantiation": "true",
-	"print_settings_id": "0.28mm Standard @Anycubic Kobra 3 V2 0.4 nozzle",
-	"layer_height": "0.28",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.4 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "2000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "auto_brim",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "10000",
-	"default_jerk": "9",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "200",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "20",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "45",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.5",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_speed": "45",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"inner_wall_line_width": "0.45",
-	"inner_wall_speed": "200",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.42",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "180",
-	"ironing_angle": "-1",
-	"ironing_flow": "10%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.42",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "15",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "9",
-	"outer_wall_line_width": "0.42",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "0%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "5",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "30",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "10%",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "30%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.45",
-	"sparse_infill_pattern": "grid",
-	"sparse_infill_speed": "200",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "100%",
-	"support_interface_top_layers": "2",
-	"support_line_width": "0.42",
-	"support_object_xy_distance": "60%",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.2",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "4",
-	"top_shell_thickness": "1",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.42",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "180",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "120%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "13ES5eks7VTR3G2E",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.3",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.6 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "500",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "5000",
-	"default_jerk": "20",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "0",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.075",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "50",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.62",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.3",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "10000",
-	"inner_wall_jerk": "15",
-	"inner_wall_line_width": "0.62",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "5000",
-	"internal_solid_infill_line_width": "0.62",
-	"internal_solid_infill_pattern": "monotonic",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.62",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "0",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "15",
-	"outer_wall_line_width": "0.62",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "15",
-	"overhang_4_4_speed": "10",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "35",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "1",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "10",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "10000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.62",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "100",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.62",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "3",
-	"top_shell_thickness": "0.6",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "5000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.62",
-	"top_surface_pattern": "monotonicline",
-	"top_surface_speed": "150",
-	"travel_acceleration": "15000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "0.8",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "150%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,17 +0,0 @@
-{
-	"type": "process",
-	"name": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "avPzsOBN3DnXTaol",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.32mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.32",
-	"initial_layer_print_height": "0.32",
-	"inner_wall_speed": "120",
-	"outer_wall_speed": "80",
-	"overhang_2_4_speed": "40",
-	"overhang_3_4_speed": "30",
-	"top_solid_infill_flow_ratio": "0.95"
-}
@@ -1,24 +0,0 @@
-{
-	"type": "process",
-	"name": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"inherits": "0.30mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"from": "system",
-	"setting_id": "7pIVSig189FDjOMY",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.36mm Standard @Anycubic Kobra 3 V2 0.6 nozzle",
-	"layer_height": "0.36",
-	"brim_type": "auto_brim",
-	"default_acceleration": "6000",
-	"default_jerk": "9",
-	"elefant_foot_compensation": "0.1",
-	"inner_wall_acceleration": "6000",
-	"inner_wall_jerk": "9",
-	"outer_wall_jerk": "9",
-	"raft_first_layer_expansion": "5",
-	"sparse_infill_acceleration": "6000",
-	"support_threshold_angle": "30",
-	"top_bottom_infill_wall_overlap": "15%",
-	"travel_acceleration": "10000",
-	"travel_jerk": "9"
-}
@@ -1,289 +0,0 @@
-{
-	"type": "process",
-	"name": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "0yxg7c5tH07ZMIL4",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.4",
-	"compatible_printers": [
-		"Anycubic Kobra 3 V2 0.8 nozzle"
-	],
-	"accel_to_decel_enable": "1",
-	"accel_to_decel_factor": "50%",
-	"alternate_extra_wall": "0",
-	"bottom_shell_layers": "3",
-	"bottom_shell_thickness": "0",
-	"bottom_solid_infill_flow_ratio": "1",
-	"bottom_surface_pattern": "monotonic",
-	"bridge_acceleration": "5000",
-	"bridge_angle": "0",
-	"bridge_density": "100%",
-	"bridge_flow": "0.9",
-	"bridge_no_support": "0",
-	"bridge_speed": "30",
-	"brim_ears_detection_length": "1",
-	"brim_ears_max_angle": "125",
-	"brim_object_gap": "0.15",
-	"brim_type": "outer_only",
-	"brim_width": "5",
-	"compatible_printers_condition": "",
-	"counterbore_hole_bridging": "none",
-	"default_acceleration": "6000",
-	"default_jerk": "20",
-	"detect_narrow_internal_solid_infill": "1",
-	"detect_overhang_wall": "1",
-	"detect_thin_wall": "1",
-	"dont_filter_internal_bridges": "disabled",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0.1",
-	"elefant_foot_compensation_layers": "1",
-	"enable_arc_fitting": "0",
-	"enable_overhang_speed": "1",
-	"enable_prime_tower": "1",
-	"enable_support": "0",
-	"enforce_support_layers": "0",
-	"ensure_vertical_shell_thickness": "ensure_all",
-	"exclude_object": "1",
-	"extra_perimeters_on_overhangs": "1",
-	"filter_out_gap_fill": "0",
-	"flush_into_infill": "0",
-	"flush_into_objects": "0",
-	"flush_into_support": "1",
-	"fuzzy_skin": "none",
-	"fuzzy_skin_first_layer": "0",
-	"fuzzy_skin_point_distance": "0.8",
-	"fuzzy_skin_thickness": "0.3",
-	"gap_fill_target": "topbottom",
-	"gap_infill_speed": "50",
-	"gcode_add_line_number": "0",
-	"gcode_comments": "0",
-	"gcode_label_objects": "1",
-	"hole_to_polyhole": "0",
-	"hole_to_polyhole_threshold": "0.01",
-	"hole_to_polyhole_twisted": "1",
-	"independent_support_layer_height": "1",
-	"infill_anchor": "400",
-	"infill_anchor_max": "10",
-	"infill_combination": "0",
-	"infill_direction": "45",
-	"infill_jerk": "9",
-	"infill_wall_overlap": "15%",
-	"initial_layer_acceleration": "500",
-	"initial_layer_infill_speed": "30",
-	"initial_layer_jerk": "9",
-	"initial_layer_line_width": "0.82",
-	"initial_layer_min_bead_width": "85%",
-	"initial_layer_print_height": "0.4",
-	"initial_layer_speed": "30",
-	"initial_layer_travel_speed": "100%",
-	"inner_wall_acceleration": "0",
-	"inner_wall_jerk": "15",
-	"inner_wall_line_width": "0.82",
-	"inner_wall_speed": "150",
-	"interface_shells": "0",
-	"internal_bridge_flow": "1",
-	"internal_bridge_speed": "150%",
-	"internal_solid_infill_acceleration": "10000",
-	"internal_solid_infill_line_width": "0.82",
-	"internal_solid_infill_pattern": "zig-zag",
-	"internal_solid_infill_speed": "150",
-	"ironing_angle": "-1",
-	"ironing_flow": "15%",
-	"ironing_pattern": "zig-zag",
-	"ironing_spacing": "0.1",
-	"ironing_speed": "15",
-	"ironing_type": "no ironing",
-	"is_infill_first": "0",
-	"line_width": "0.82",
-	"make_overhang_printable": "0",
-	"make_overhang_printable_angle": "55",
-	"make_overhang_printable_hole_size": "0",
-	"max_bridge_length": "10",
-	"max_travel_detour_distance": "0",
-	"max_volumetric_extrusion_rate_slope": "0",
-	"max_volumetric_extrusion_rate_slope_segment_length": "5",
-	"min_bead_width": "85%",
-	"min_feature_size": "25%",
-	"min_length_factor": "0.5",
-	"min_width_top_surface": "300%",
-	"minimum_sparse_infill_area": "0",
-	"mmu_segmented_region_interlocking_depth": "0",
-	"mmu_segmented_region_max_width": "0",
-	"notes": "",
-	"only_one_wall_first_layer": "0",
-	"only_one_wall_top": "1",
-	"ooze_prevention": "0",
-	"outer_wall_acceleration": "5000",
-	"outer_wall_jerk": "15",
-	"outer_wall_line_width": "0.82",
-	"outer_wall_speed": "120",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "25",
-	"overhang_4_4_speed": "5",
-	"overhang_reverse": "0",
-	"overhang_reverse_internal_only": "0",
-	"overhang_reverse_threshold": "50%",
-	"post_process": [],
-	"precise_outer_wall": "0",
-	"precise_z_height": "0",
-	"prime_tower_brim_width": "5",
-	"prime_tower_width": "35",
-	"prime_volume": "20",
-	"print_flow_ratio": "1",
-	"print_order": "default",
-	"print_sequence": "by layer",
-	"raft_contact_distance": "0.1",
-	"raft_expansion": "1.5",
-	"raft_first_layer_density": "90%",
-	"raft_first_layer_expansion": "2",
-	"raft_layers": "0",
-	"reduce_crossing_wall": "0",
-	"reduce_infill_retraction": "1",
-	"resolution": "0.012",
-	"role_based_wipe_speed": "1",
-	"rotate_solid_infill_direction": "1",
-	"scarf_angle_threshold": "155",
-	"scarf_joint_flow_ratio": "1",
-	"scarf_joint_speed": "100%",
-	"scarf_overhang_threshold": "40%",
-	"seam_gap": "10%",
-	"seam_position": "aligned",
-	"seam_slope_conditional": "0",
-	"seam_slope_entire_loop": "0",
-	"seam_slope_inner_walls": "0",
-	"seam_slope_min_length": "20",
-	"seam_slope_start_height": "0",
-	"seam_slope_steps": "10",
-	"seam_slope_type": "none",
-	"single_extruder_multi_material_priming": "0",
-	"skirt_distance": "2",
-	"skirt_height": "1",
-	"skirt_loops": "0",
-	"skirt_speed": "50",
-	"slice_closing_radius": "0.049",
-	"slicing_mode": "regular",
-	"slow_down_layers": "1",
-	"slowdown_for_curled_perimeters": "0",
-	"small_area_infill_flow_compensation": "0",
-	"small_area_infill_flow_compensation_model": [
-		"0,0",
-		"\n0.2,0.4444",
-		"\n0.4,0.6145",
-		"\n0.6,0.7059",
-		"\n0.8,0.7619",
-		"\n1.5,0.8571",
-		"\n2,0.8889",
-		"\n3,0.9231",
-		"\n5,0.9520",
-		"\n10,1"
-	],
-	"small_perimeter_speed": "50%",
-	"small_perimeter_threshold": "0",
-	"solid_infill_direction": "45",
-	"solid_infill_filament": "1",
-	"sparse_infill_acceleration": "5000",
-	"sparse_infill_density": "15%",
-	"sparse_infill_filament": "1",
-	"sparse_infill_line_width": "0.82",
-	"sparse_infill_pattern": "3dhoneycomb",
-	"sparse_infill_speed": "100",
-	"spiral_mode": "0",
-	"spiral_mode_max_xy_smoothing": "200%",
-	"spiral_mode_smooth": "0",
-	"staggered_inner_seams": "0",
-	"standby_temperature_delta": "0",
-	"support_angle": "0",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "0.2",
-	"support_bottom_interface_spacing": "0.5",
-	"support_bottom_z_distance": "0.2",
-	"support_critical_regions_only": "0",
-	"support_expansion": "0",
-	"support_filament": "0",
-	"support_interface_bottom_layers": "-1",
-	"support_interface_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_not_for_body": "1",
-	"support_interface_pattern": "auto",
-	"support_interface_spacing": "0.2",
-	"support_interface_speed": "80",
-	"support_interface_top_layers": "3",
-	"support_line_width": "0.82",
-	"support_object_xy_distance": "0.35",
-	"support_on_build_plate_only": "1",
-	"support_remove_small_overhang": "1",
-	"support_speed": "100",
-	"support_style": "default",
-	"support_threshold_angle": "40",
-	"support_top_z_distance": "0.25",
-	"support_type": "tree(auto)",
-	"thick_bridges": "0",
-	"thick_internal_bridges": "1",
-	"timelapse_type": "0",
-	"top_bottom_infill_wall_overlap": "25%",
-	"top_shell_layers": "3",
-	"top_shell_thickness": "0.8",
-	"top_solid_infill_flow_ratio": "0.97",
-	"top_surface_acceleration": "2000",
-	"top_surface_jerk": "9",
-	"top_surface_line_width": "0.82",
-	"top_surface_pattern": "monotonic",
-	"top_surface_speed": "150",
-	"travel_acceleration": "10000",
-	"travel_jerk": "12",
-	"travel_speed": "350",
-	"travel_speed_z": "0",
-	"tree_support_adaptive_layer_height": "1",
-	"tree_support_angle_slow": "25",
-	"tree_support_auto_brim": "1",
-	"tree_support_branch_angle": "40",
-	"tree_support_branch_angle_organic": "40",
-	"tree_support_branch_diameter": "5",
-	"tree_support_branch_diameter_angle": "5",
-	"tree_support_branch_diameter_double_wall": "3",
-	"tree_support_branch_diameter_organic": "2",
-	"tree_support_branch_distance": "5",
-	"tree_support_branch_distance_organic": "1",
-	"tree_support_brim_width": "3",
-	"tree_support_tip_diameter": "1.5",
-	"tree_support_top_rate": "30%",
-	"tree_support_wall_count": "0",
-	"wall_direction": "auto",
-	"wall_distribution_count": "1",
-	"wall_filament": "1",
-	"wall_generator": "classic",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"wall_loops": "2",
-	"wall_sequence": "inner wall/outer wall",
-	"wall_transition_angle": "10",
-	"wall_transition_filter_deviation": "25%",
-	"wall_transition_length": "100%",
-	"wipe_before_external_loop": "0",
-	"wipe_on_loops": "0",
-	"wipe_speed": "80%",
-	"wipe_tower_bridging": "10",
-	"wipe_tower_cone_angle": "15",
-	"wipe_tower_extra_spacing": "150%",
-	"wipe_tower_extruder": "0",
-	"wipe_tower_max_purge_speed": "90",
-	"wipe_tower_no_sparse_layers": "0",
-	"wipe_tower_rotation_angle": "0",
-	"wiping_volumes_extruders": [
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70",
-		"70"
-	],
-	"xy_contour_compensation": "0",
-	"xy_hole_compensation": "0"
-}
@@ -1,17 +0,0 @@
-{
-	"type": "process",
-	"name": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"inherits": "0.40mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"from": "system",
-	"setting_id": "2cCCPfRX7H33XrMb",
-	"instantiation": "true",
-	"filename_format": "{timestamp}-{if plate_name==\"\" then input_filename_base+\"_plate\" else plate_name endif}{\"(\"+plate_number+\")\"}_{filament_type[initial_tool]}_{layer_height}_{print_time}.gcode",
-	"print_settings_id": "0.48mm Standard @Anycubic Kobra 3 V2 0.8 nozzle",
-	"layer_height": "0.48",
-	"initial_layer_print_height": "0.48",
-	"inner_wall_speed": "180",
-	"outer_wall_speed": "140",
-	"overhang_2_4_speed": "40",
-	"overhang_3_4_speed": "30",
-	"top_solid_infill_flow_ratio": "0.95"
-}
--- a/Show More
+++ b/Show More