Merge branch 'main' into feature/wipetower2_travel_path

The linear approximation used a heuristic segment count clamped to 4..16, so the
lift ran as a coarse polygon. Every vertex is a direction change large enough to
hit the firmware's jerk limit, forcing a decelerate/accelerate at each corner —
the lift micro-stutters instead of running at speed. The segment count now comes
from the chord deviation against the slicing resolution, reusing
Geometry::ArcWelder::arc_discretization_steps, which keeps the turn at each
vertex shallow enough for the firmware to carry speed through the whole move.

Points are emitted through GCodeG1Formatter so they carry the same quantization
as the rest of the G-code, and the move comment now trails the feedrate line to
match _travel_to_z and the G2/G3 branch. No change when arc fitting is enabled.

CMakeLists.txt

@@ -80,8 +80,12 @@ endif()
 
 if (DEFINED BBL_RELEASE_TO_PUBLIC)
     add_compile_definitions("BBL_RELEASE_TO_PUBLIC=${BBL_RELEASE_TO_PUBLIC}")
+    if (BBL_RELEASE_TO_PUBLIC)
+        add_compile_definitions(WXINSPECTOR_DISABLE)
+    endif ()
 else ()
     add_compile_definitions("BBL_RELEASE_TO_PUBLIC=$<CONFIG:Release>")
+    add_compile_definitions("$<$<CONFIG:Release>:WXINSPECTOR_DISABLE>")
 endif ()
 
 find_package(Git)

deps/OpenSSL/OpenSSL.cmake

@@ -52,6 +52,14 @@ ExternalProject_Add(dep_OpenSSL
 	CONFIGURE_COMMAND ${_conf_cmd} ${_cross_arch}
         "--openssldir=${DESTDIR}"
         "--prefix=${DESTDIR}"
+        # OpenSSL's linux-x86_64 target sets multilib=64, so it installs to
+        # <prefix>/lib64 while every other dep uses <prefix>/lib. CPython's
+        # --with-openssl only ever emits -L<dir>/lib, so it misses the bundled
+        # static libs and silently links the system OpenSSL instead -- which,
+        # against 1.1.1w headers, leaves _ssl.so with an undefined
+        # SSL_get_peer_certificate (removed in OpenSSL 3.x). Pin libdir so the
+        # prefix stays single-layout.
+        "--libdir=lib"
         ${_cross_comp_prefix_line}
         no-shared
         no-asm

deps_src/imgui/imstb_textedit.h

@@ -465,6 +465,57 @@ static void stb_textedit_click(STB_TEXTEDIT_STRING *str, STB_TexteditState *stat
       STB_TEXTEDIT_LAYOUTROW(&r, str, 0);
       y = r.ymin;
    }
+   else
+   {
+      // In multi-line mode, clamp y to stay within the text vertical bounds.
+      // This lets the click still land at a valid location if the mouse is slightly
+      // above or below the text.
+      StbTexteditRow r;
+      int n = STB_TEXTEDIT_STRINGLEN(str);
+      int i = 0;
+      float base_y = 0, y_min, y_max;
+
+      // Get the first row to establish y_min and start the iteration
+      STB_TEXTEDIT_LAYOUTROW(&r, str, 0);
+      if (r.num_chars <= 0)
+      {
+         state->cursor = 0;
+         state->select_start = state->cursor;
+         state->select_end = state->cursor;
+         state->has_preferred_x = 0;
+         return;
+      }
+      y_min = r.ymin;
+      y_max = base_y + r.ymax;
+      i = r.num_chars;
+      base_y += r.baseline_y_delta;
+
+      // Walk the remaining rows to find the bottom of the last row
+      while (i < n)
+      {
+         STB_TEXTEDIT_LAYOUTROW(&r, str, i);
+         if (r.num_chars <= 0)
+            break;
+         y_max = base_y + r.ymax;
+         i += r.num_chars;
+         base_y += r.baseline_y_delta;
+      }
+
+      // If the text ends with a newline, account for the empty trailing line
+      // so the cursor can be placed on it
+      if (n > 0 && STB_TEXTEDIT_GETCHAR(str, n - 1) == STB_TEXTEDIT_NEWLINE)
+      {
+         STB_TEXTEDIT_LAYOUTROW(&r, str, n);
+         y_max = base_y + r.ymax;
+      }
+
+      // Subtract half the last line height to avoid rounding issues when the mouse
+      // is just barely below the last line (keep cursor on the last line, not after the text)
+      y_max -= (r.ymax - r.ymin) * 0.5f;
+
+      if (y < y_min) y = y_min;
+      if (y > y_max) y = y_max;
+   }
 
    state->cursor = stb_text_locate_coord(str, x, y);
    state->select_start = state->cursor;
@@ -485,6 +536,50 @@ static void stb_textedit_drag(STB_TEXTEDIT_STRING *str, STB_TexteditState *state
       STB_TEXTEDIT_LAYOUTROW(&r, str, 0);
       y = r.ymin;
    }
+   else
+   {
+      // In multi-line mode, clamp y to stay within the text vertical bounds.
+      // This lets the drag keep working if the mouse goes off the top or bottom of the text.
+      StbTexteditRow r;
+      int n = STB_TEXTEDIT_STRINGLEN(str);
+      int i = 0;
+      float base_y = 0, y_min, y_max;
+
+      // Get the first row to establish y_min and start the iteration
+      STB_TEXTEDIT_LAYOUTROW(&r, str, 0);
+      if (r.num_chars <= 0)
+         return;
+      y_min = r.ymin;
+      y_max = base_y + r.ymax;
+      i = r.num_chars;
+      base_y += r.baseline_y_delta;
+
+      // Walk the remaining rows to find the bottom of the last row
+      while (i < n)
+      {
+         STB_TEXTEDIT_LAYOUTROW(&r, str, i);
+         if (r.num_chars <= 0)
+            break;
+         y_max = base_y + r.ymax;
+         i += r.num_chars;
+         base_y += r.baseline_y_delta;
+      }
+
+      // If the text ends with a newline, account for the empty trailing line
+      // so the cursor can be placed on it
+      if (n > 0 && STB_TEXTEDIT_GETCHAR(str, n - 1) == STB_TEXTEDIT_NEWLINE)
+      {
+         STB_TEXTEDIT_LAYOUTROW(&r, str, n);
+         y_max = base_y + r.ymax;
+      }
+
+      // Subtract half the last line height to avoid rounding issues when the mouse
+      // is just barely below the last line (keep cursor on the last line, not after the text)
+      y_max -= (r.ymax - r.ymin) * 0.5f;
+
+      if (y < y_min) y = y_min;
+      if (y > y_max) y = y_max;
+   }
 
    if (state->select_start == state->select_end)
       state->select_start = state->cursor;

resources/calib/temperature_tower/gen_belt_temp_tower.py

@@ -1,79 +0,0 @@
-#!/usr/bin/env python3
-"""Belt temperature-tower asset generator (discrete-provini design).
-
-A vertical temperature tower cannot be sliced on a belt printer, so lay a row of
-DISCRETE provini (one per temperature) along the belt (designed Y) with a fixed
-surface gap. Each provino is the chevron+arc unit (belt_temp_provino_unit.stl,
-keel-first); its temperature is ENGRAVED upright into the 50 mm face — a raised
-number would be an unsupported overhang on the belt. The C++ calib_temp belt branch
-(Plater.cpp) injects one M104 per zone 70 layers INTO provino i:
-  print_z[i] = i * PITCH * cos(theta) + 70 * layer_height   (theta = 45)
-inside the body, not in the empty inter-provino gap (which has no sliced layers for
-the event to attach to). PITCH below is the shared geometry contract with that code —
-keep them in sync.
-
-Generates one STL per filament temp range used by Temp_Calibration_Dlg.
-"""
-import numpy as np, trimesh, os
-from matplotlib.textpath import TextPath
-from matplotlib.font_manager import FontProperties
-from shapely.geometry import Polygon as ShPoly
-from shapely.ops import unary_union
-
-HERE = os.path.dirname(os.path.abspath(__file__))
-UNIT = os.path.join(HERE, 'belt_temp_provino_unit.stl')   # single provino, keel-first
-SURF_GAP = 25.0            # surface-to-surface gap between provini (mm) — user spec
-TEXT_H = 9.0
-TEXT_DEPTH = 0.8           # engraving depth (numbers are CUT into the face, not raised:
-                          # a raised number is an unsupported Y-overhang on the belt)
-TEXT_OVERSHOOT = 0.6       # extra height poking out of the face for a clean boolean cut
-
-# Temperature ranges (start, end) per filament family, 5 C step. File name encodes them.
-RANGES = [(230,190),(270,230),(250,230),(280,240),(240,210),(320,280)]
-
-unit = trimesh.load(UNIT)
-dY = unit.bounds[1,1] - unit.bounds[0,1]
-PITCH = dY + SURF_GAP                       # designed-Y pitch == C++ contract constant
-print(f"unit dY={dY:.2f}  PITCH={PITCH:.3f}  (C++ contract: print_z[i]=i*{PITCH:.3f}*cos45)")
-
-# 50 mm face normal (0,-1,1)/sqrt2 ; UPRIGHT basis u=+X det(+1) (verified non-mirrored)
-n = np.array([0,-1,1.])/np.sqrt(2)
-u = np.array([1,0,0.]); v = np.array([0,1,1.])/np.sqrt(2)
-R = np.column_stack([u,v,n])
-fn = unit.face_normals; fc = unit.triangles_center; fa = unit.area_faces
-sel = (fn@n) > 0.9
-face_c = (fc[sel]*fa[sel,None]).sum(0)/fa[sel].sum()
-
-def text_mesh(s):
-    tp = TextPath((0,0), s, size=TEXT_H, prop=FontProperties(family='DejaVu Sans'))
-    rings = [ShPoly(p) for p in tp.to_polygons() if len(p)>=3]
-    rings.sort(key=lambda r:r.area, reverse=True)
-    used=[False]*len(rings); parts=[]
-    for i,o in enumerate(rings):
-        if used[i]: continue
-        holes=[]
-        for j in range(i+1,len(rings)):
-            if not used[j] and o.contains(rings[j]): holes.append(rings[j].exterior.coords); used[j]=True
-        parts.append(ShPoly(o.exterior.coords,holes)); used[i]=True
-    poly = unary_union(parts)
-    geoms = list(poly.geoms) if poly.geom_type=='MultiPolygon' else [poly]
-    m = trimesh.util.concatenate([trimesh.creation.extrude_polygon(g,height=TEXT_DEPTH+TEXT_OVERSHOOT) for g in geoms])
-    c = m.bounds.mean(axis=0); m.apply_translation([-c[0],-c[1],0]); return m
-
-for t_start, t_end in RANGES:
-    temps = list(range(t_start, t_end-1, -5))
-    parts=[]
-    for i,T in enumerate(temps):
-        c = unit.copy(); c.apply_translation([0, i*PITCH, 0])
-        t = text_mesh(str(T)); M=np.eye(4); M[:3,:3]=R; t.apply_transform(M)
-        # place the text spanning from TEXT_DEPTH inside the face to TEXT_OVERSHOOT outside,
-        # then CUT it out of the provino (engrave) — no raised material, no Y-overhang.
-        t.apply_translation(face_c - n*TEXT_DEPTH + np.array([0,i*PITCH,0]))
-        c = trimesh.boolean.difference([c, t], engine='manifold')
-        parts.append(c)
-    asset = trimesh.util.concatenate(parts)
-    out = os.path.join(HERE, f"belt_temp_tower_{t_start}_{t_end}.stl")
-    asset.export(out)
-    dims = np.round(asset.bounds[1]-asset.bounds[0],1)
-    wt = all(p.is_watertight for p in parts)
-    print(f"  {t_start}->{t_end}: {len(temps)} zones  bbox={dims}  watertight={wt}  -> {os.path.basename(out)}")

resources/profiles/Custom.json

@@ -1,13 +1,9 @@
 {
 	"name": "Custom Printer",
-	"version": "02.04.00.04",
+	"version": "02.04.00.03",
 	"force_update": "0",
 	"description": "My configurations",
 	"machine_model_list": [
-		{
-			"name": "Generic Belt Printer",
-			"sub_path": "machine/MyBeltPrinter.json"
-		},
 		{
 			"name": "Generic Klipper Printer",
 			"sub_path": "machine/MyKlipper.json"
@@ -66,14 +62,6 @@
 			"name": "0.16mm Optimal @MyKlipper",
 			"sub_path": "process/0.16mm Optimal @MyKlipper.json"
 		},
-		{
-			"name": "0.12mm Fine @MyBeltPrinter",
-			"sub_path": "process/0.12mm Fine @MyBeltPrinter.json"
-		},
-		{
-			"name": "0.20mm Standard @MyBeltPrinter",
-			"sub_path": "process/0.20mm Standard @MyBeltPrinter.json"
-		},
 		{
 			"name": "0.20mm Standard @MyKlipper",
 			"sub_path": "process/0.20mm Standard @MyKlipper.json"
@@ -274,38 +262,18 @@
 			"name": "MyKlipper 0.8 nozzle",
 			"sub_path": "machine/MyKlipper 0.8 nozzle.json"
 		},
-		{
-			"name": "fdm_belt_common",
-			"sub_path": "machine/fdm_belt_common.json"
-		},
 		{
 			"name": "fdm_toolchanger_common",
 			"sub_path": "machine/fdm_toolchanger_common.json"
 		},
-		{
-			"name": "MyRRF 0.4 nozzle",
-			"sub_path": "machine/MyRRF 0.4 nozzle.json"
-		},
-		{
-			"name": "MyBeltPrinter 0.2 nozzle",
-			"sub_path": "machine/MyBeltPrinter 0.2 nozzle.json"
-		},
-		{
-			"name": "MyBeltPrinter 0.4 nozzle",
-			"sub_path": "machine/MyBeltPrinter 0.4 nozzle.json"
-		},
-		{
-			"name": "MyBeltPrinter 0.6 nozzle",
-			"sub_path": "machine/MyBeltPrinter 0.6 nozzle.json"
-		},
-		{
-			"name": "MyBeltPrinter 0.8 nozzle",
-			"sub_path": "machine/MyBeltPrinter 0.8 nozzle.json"
-		},
 		{
 			"name": "MyRepetier 0.4 nozzle",
 			"sub_path": "machine/MyRepetier 0.4 nozzle.json"
 		},
+		{
+			"name": "MyRRF 0.4 nozzle",
+			"sub_path": "machine/MyRRF 0.4 nozzle.json"
+		},
 		{
 			"name": "MyToolChanger 0.2 nozzle",
 			"sub_path": "machine/MyToolChanger 0.2 nozzle.json"

resources/profiles/Custom/filament/Generic ABS @MyToolChanger.json

@@ -24,12 +24,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic ASA @MyToolChanger.json

@@ -24,12 +24,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PA @MyToolChanger.json

@@ -24,12 +24,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PA-CF @MyToolChanger.json

@@ -24,12 +24,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PC @MyToolChanger.json

@@ -25,12 +25,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PETG @MyToolChanger.json

@@ -25,12 +25,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PLA @MyToolChanger.json

@@ -25,12 +25,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PLA-CF @MyToolChanger.json

@@ -25,12 +25,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/filament/Generic PVA @MyToolChanger.json

@@ -25,12 +25,6 @@
 	"filament_loading_speed_start": [
 		"50"
 	],
-	"filament_multitool_ramming": [
-		"1"
-	],
-	"filament_multitool_ramming_flow": [
-		"40"
-	],
 	"filament_stamping_distance": [
 		"45"
 	],

resources/profiles/Custom/machine/MyBeltPrinter 0.2 nozzle.json

@@ -1,27 +0,0 @@
-{
-	"type": "machine",
-	"name": "MyBeltPrinter 0.2 nozzle",
-	"inherits": "fdm_belt_common",
-	"from": "system",
-	"setting_id": "3w1uyJdmm14QhDnH",
-	"instantiation": "true",
-	"printer_model": "Generic Belt Printer",
-	"default_print_profile": "0.12mm Fine @MyBeltPrinter",
-	"nozzle_diameter": [
-		"0.2"
-	],
-	"max_layer_height": [
-		"0.16"
-	],
-	"min_layer_height": [
-		"0.04"
-	],
-	"printer_variant": "0.2",
-	"printable_area": [
-		"0x0",
-		"350x0",
-		"350x350",
-		"0x350"
-	],
-	"printable_height": "300"
-}

resources/profiles/Custom/machine/MyBeltPrinter 0.4 nozzle.json

@@ -1,20 +0,0 @@
-{
-	"type": "machine",
-	"name": "MyBeltPrinter 0.4 nozzle",
-	"inherits": "fdm_belt_common",
-	"from": "system",
-	"setting_id": "6nRHUtvJOUffocbu",
-	"instantiation": "true",
-	"printer_model": "Generic Belt Printer",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"printer_variant": "0.4",
-	"printable_area": [
-		"0x0",
-		"350x0",
-		"350x350",
-		"0x350"
-	],
-	"printable_height": "300"
-}

resources/profiles/Custom/machine/MyBeltPrinter 0.6 nozzle.json

@@ -1,26 +0,0 @@
-{
-	"type": "machine",
-	"name": "MyBeltPrinter 0.6 nozzle",
-	"inherits": "fdm_belt_common",
-	"from": "system",
-	"setting_id": "K0m9HbUNwKT4UCJV",
-	"instantiation": "true",
-	"printer_model": "Generic Belt Printer",
-	"nozzle_diameter": [
-		"0.6"
-	],
-	"max_layer_height": [
-		"0.4"
-	],
-	"min_layer_height": [
-		"0.12"
-	],
-	"printer_variant": "0.6",
-	"printable_area": [
-		"0x0",
-		"350x0",
-		"350x350",
-		"0x350"
-	],
-	"printable_height": "300"
-}

resources/profiles/Custom/machine/MyBeltPrinter 0.8 nozzle.json

@@ -1,26 +0,0 @@
-{
-	"type": "machine",
-	"name": "MyBeltPrinter 0.8 nozzle",
-	"inherits": "fdm_belt_common",
-	"from": "system",
-	"setting_id": "rHAweDz4eNwttPNA",
-	"instantiation": "true",
-	"printer_model": "Generic Belt Printer",
-	"nozzle_diameter": [
-		"0.8"
-	],
-	"max_layer_height": [
-		"0.6"
-	],
-	"min_layer_height": [
-		"0.2"
-	],
-	"printer_variant": "0.8",
-	"printable_area": [
-		"0x0",
-		"350x0",
-		"350x350",
-		"0x350"
-	],
-	"printable_height": "300"
-}

resources/profiles/Custom/machine/MyBeltPrinter.json

@@ -1,12 +0,0 @@
-{
-	"type": "machine_model",
-	"name": "Generic Belt Printer",
-	"model_id": "my_belt_01",
-	"nozzle_diameter": "0.4;0.2;0.6;0.8",
-	"machine_tech": "FFF",
-	"family": "MyPrinter",
-	"bed_model": "Custom_350_bed.stl",
-	"bed_texture": "orcaslicer_bed_texture.svg",
-	"hotend_model": "",
-	"default_materials": "Generic PLA @System;Generic PLA-CF @System;Generic PETG @System;Generic TPU @System;Generic PC @System;Generic PVA @System;Generic PA @System;Generic PA-CF @System"
-}

resources/profiles/Custom/machine/fdm_belt_common.json

@@ -1,99 +0,0 @@
-{
-	"type": "machine",
-	"name": "fdm_belt_common",
-	"inherits": "fdm_klipper_common",
-	"from": "system",
-	"instantiation": "false",
-	"gcode_flavor": "klipper",
-	"single_extruder_multi_material": "0",
-	"default_filament_profile": [
-		"Generic PLA @System"
-	],
-	"default_print_profile": "0.20mm Standard @MyBeltPrinter",
-	"max_layer_height": [
-		"0.32"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"deretraction_speed": [
-		"30"
-	],
-	"extruder_colour": [
-		"#FCE94F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"retract_before_wipe": [
-		"70%"
-	],
-	"retract_length_toolchange": [
-		"2"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"0"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"18"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"30"
-	],
-	"travel_slope": [
-		"3"
-	],
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"1"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Normal Lift"
-	],
-	"gcode_remap_x": "rev_x",
-	"gcode_remap_y": "pos_z",
-	"gcode_remap_z": "pos_y",
-	"printer_extruder_id": [
-		"1"
-	],
-	"belt_printer": "1",
-	"belt_slice_rotation": "x",
-	"belt_slice_rotation_angle": "45",
-	"belt_slice_rotation_global": "1",
-	"build_plate_tilt_x": "45",
-	"purge_in_prime_tower": "0",
-	"scan_first_layer": "0",
-	"auxiliary_fan": "0"
-}

resources/profiles/Custom/machine/fdm_klipper_common.json

@@ -116,7 +116,7 @@
 	"deretraction_speed": [
 		"30"
 	],
-	"z_hop_types": "Normal Lift",
+	"z_hop_types": "Slope Lift",
 	"silent_mode": "0",
 	"single_extruder_multi_material": "1",
 	"change_filament_gcode": "",

resources/profiles/Custom/machine/fdm_repetier_common.json

@@ -118,7 +118,7 @@
 	"deretraction_speed": [
 		"30"
 	],
-	"z_hop_types": "Normal Lift",
+	"z_hop_types": "Slope Lift",
 	"silent_mode": "0",
 	"single_extruder_multi_material": "1",
 	"change_filament_gcode": "",

resources/profiles/Custom/machine/fdm_rrf_common.json

@@ -116,7 +116,7 @@
 	"deretraction_speed": [
 		"30"
 	],
-	"z_hop_types": "Normal Lift",
+	"z_hop_types": "Slope Lift",
 	"silent_mode": "0",
 	"single_extruder_multi_material": "1",
 	"change_filament_gcode": "",

resources/profiles/Custom/machine/fdm_toolchanger_common.json

@@ -6,6 +6,7 @@
 	"instantiation": "false",
 	"gcode_flavor": "klipper",
 	"single_extruder_multi_material": "0",
+	"wait_for_temp_on_wipe_tower": "1",
 	"default_filament_profile": [
 		"Generic PLA @MyToolChanger"
 	],
@@ -172,11 +173,11 @@
 		"0.4"
 	],
 	"z_hop_types": [
-		"Normal Lift",
-		"Normal Lift",
-		"Normal Lift",
-		"Normal Lift",
-		"Normal Lift"
+		"Slope Lift",
+		"Slope Lift",
+		"Slope Lift",
+		"Slope Lift",
+		"Slope Lift"
 	],
 	"purge_in_prime_tower": "0",
 	"machine_pause_gcode": "M601",

resources/profiles/Custom/process/0.12mm Fine @MyBeltPrinter.json

@@ -1,20 +0,0 @@
-{
-	"type": "process",
-	"name": "0.12mm Fine @MyBeltPrinter",
-	"inherits": "fdm_process_klipper_common",
-	"from": "system",
-	"setting_id": "EugqqdLJ423bgEwN",
-	"instantiation": "true",
-	"layer_height": "0.12",
-	"initial_layer_print_height": "0.12",
-	"bottom_shell_layers": "5",
-	"top_shell_layers": "6",
-	"support_top_z_distance": "0.08",
-	"support_bottom_z_distance": "0.08",
-	"skirt_loops": "0",
-	"skirt_distance": "0",
-	"compatible_printers": [
-		"MyBeltPrinter 0.2 nozzle",
-		"MyBeltPrinter 0.4 nozzle"
-	]
-}

resources/profiles/Custom/process/0.20mm Standard @MyBeltPrinter.json

@@ -1,17 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm Standard @MyBeltPrinter",
-	"inherits": "fdm_process_klipper_common",
-	"from": "system",
-	"setting_id": "YzCDAgH3uLOM53pF",
-	"instantiation": "true",
-	"layer_height": "0.2",
-	"initial_layer_print_height": "0.2",
-	"skirt_loops": "0",
-	"skirt_distance": "0",
-	"compatible_printers": [
-		"MyBeltPrinter 0.4 nozzle",
-		"MyBeltPrinter 0.6 nozzle",
-		"MyBeltPrinter 0.8 nozzle"
-	]
-}

resources/profiles/IdeaFormer.json

@@ -1,54 +0,0 @@
-{
-    "name": "IdeaFormer",
-    "version": "02.00.00.03",
-    "force_update": "0",
-    "description": "IdeaFormer belt printer configurations",
-    "machine_model_list": [
-        {
-            "name": "IdeaFormer IR3 V2",
-            "sub_path": "machine/IdeaFormer IR3 V2.json"
-        }
-    ],
-    "process_list": [
-        {
-            "name": "fdm_process_common",
-            "sub_path": "process/fdm_process_common.json"
-        },
-        {
-            "name": "0.20mm Standard @IdeaFormer IR3 V2",
-            "sub_path": "process/0.20mm Standard @IdeaFormer IR3 V2.json"
-        }
-    ],
-    "filament_list": [
-        {
-            "name": "Generic PLA @IdeaFormer IR3 V2",
-            "sub_path": "filament/Generic PLA @IdeaFormer IR3 V2.json"
-        },
-        {
-            "name": "eSUN PLA @IdeaFormer IR3 V2",
-            "sub_path": "filament/eSUN PLA @IdeaFormer IR3 V2.json"
-        },
-        {
-            "name": "Generic PETG @IdeaFormer IR3 V2",
-            "sub_path": "filament/Generic PETG @IdeaFormer IR3 V2.json"
-        }
-    ],
-    "machine_list": [
-        {
-            "name": "fdm_machine_common",
-            "sub_path": "machine/fdm_machine_common.json"
-        },
-        {
-            "name": "fdm_klipper_common",
-            "sub_path": "machine/fdm_klipper_common.json"
-        },
-        {
-            "name": "fdm_belt_common",
-            "sub_path": "machine/fdm_belt_common.json"
-        },
-        {
-            "name": "IdeaFormer IR3 V2 0.4 nozzle",
-            "sub_path": "machine/IdeaFormer IR3 V2 0.4 nozzle.json"
-        }
-    ]
-}

resources/profiles/IdeaFormer/filament/Generic PETG @IdeaFormer IR3 V2.json

@@ -1,113 +0,0 @@
-{
-	"type": "filament",
-	"name": "Generic PETG @IdeaFormer IR3 V2",
-	"inherits": "Generic PETG @System",
-	"from": "system",
-	"setting_id": "n4zaXcUUzTqAxq5f",
-	"instantiation": "true",
-	"compatible_printers": [
-		"IdeaFormer IR3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PETG"
-	],
-	"filament_vendor": [
-		"Generic"
-	],
-	"filament_settings_id": [
-		"Generic PETG @IdeaFormer IR3 V2"
-	],
-	"filament_diameter": [
-		"1.75"
-	],
-	"filament_density": [
-		"1.27"
-	],
-	"filament_flow_ratio": [
-		"0.95"
-	],
-	"filament_cost": [
-		"25"
-	],
-	"filament_max_volumetric_speed": [
-		"10"
-	],
-	"nozzle_temperature": [
-		"240"
-	],
-	"nozzle_temperature_initial_layer": [
-		"245"
-	],
-	"nozzle_temperature_range_low": [
-		"220"
-	],
-	"nozzle_temperature_range_high": [
-		"260"
-	],
-	"temperature_vitrification": [
-		"70"
-	],
-	"hot_plate_temp": [
-		"80"
-	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
-	"cool_plate_temp": [
-		"80"
-	],
-	"cool_plate_temp_initial_layer": [
-		"80"
-	],
-	"textured_plate_temp": [
-		"80"
-	],
-	"textured_plate_temp_initial_layer": [
-		"80"
-	],
-	"fan_min_speed": [
-		"40"
-	],
-	"fan_max_speed": [
-		"60"
-	],
-	"overhang_fan_threshold": [
-		"25%"
-	],
-	"overhang_fan_speed": [
-		"80"
-	],
-	"close_fan_the_first_x_layers": [
-		"3"
-	],
-	"full_fan_speed_layer": [
-		"8"
-	],
-	"slow_down_min_speed": [
-		"20"
-	],
-	"slow_down_layer_time": [
-		"4"
-	],
-	"fan_cooling_layer_time": [
-		"100"
-	],
-	"reduce_fan_stop_start_freq": [
-		"1"
-	],
-	"filament_retraction_length": [
-		"2"
-	],
-	"filament_retraction_speed": [
-		"40"
-	],
-	"filament_deretraction_speed": [
-		"40"
-	],
-	"filament_z_hop": [
-		"0.4"
-	],
-	"filament_start_gcode": [
-		"; Generic PETG @IdeaFormer IR3 V2 — belt PETG, bed 80C"
-	]
-}

resources/profiles/IdeaFormer/filament/eSUN PLA @IdeaFormer IR3 V2.json

@@ -1,35 +0,0 @@
-{
-	"type": "filament",
-	"name": "eSUN PLA @IdeaFormer IR3 V2",
-	"inherits": "Generic PLA @IdeaFormer IR3 V2",
-	"from": "system",
-	"setting_id": "XqkviBmFHEglXueX",
-	"instantiation": "true",
-	"compatible_printers": [
-		"IdeaFormer IR3 V2 0.4 nozzle"
-	],
-	"filament_type": [
-		"PLA"
-	],
-	"filament_vendor": [
-		"eSUN"
-	],
-	"filament_settings_id": [
-		"eSUN PLA @IdeaFormer IR3 V2"
-	],
-	"nozzle_temperature_initial_layer": [
-		"200"
-	],
-	"nozzle_temperature": [
-		"200"
-	],
-	"enable_pressure_advance": [
-		"1"
-	],
-	"pressure_advance": [
-		"0.12"
-	],
-	"filament_max_volumetric_speed": [
-		"20"
-	]
-}

resources/profiles/IdeaFormer/machine/IdeaFormer IR3 V2 0.4 nozzle.json

@@ -1,94 +0,0 @@
-{
-	"type": "machine",
-	"name": "IdeaFormer IR3 V2 0.4 nozzle",
-	"inherits": "fdm_belt_common",
-	"from": "system",
-	"setting_id": "MDQZgwRgg72lmjtu",
-	"instantiation": "true",
-	"printer_model": "IdeaFormer IR3 V2",
-	"printer_variant": "0.4",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"printable_area": [
-		"0x0",
-		"250x0",
-		"250x2000",
-		"0x2000"
-	],
-	"printable_height": "250",
-	"belt_printer_infinite_y": "1",
-	"thumbnails": [
-		"48x48/PNG",
-		"300x300/PNG"
-	],
-	"default_filament_profile": [
-		"Generic PLA @IdeaFormer IR3 V2"
-	],
-	"default_print_profile": "0.20mm Standard @IdeaFormer IR3 V2",
-	"use_relative_e_distances": "1",
-	"machine_max_acceleration_e": [
-		"5000"
-	],
-	"machine_max_acceleration_extruding": [
-		"5000"
-	],
-	"machine_max_acceleration_retracting": [
-		"1000"
-	],
-	"machine_max_acceleration_travel": [
-		"9000"
-	],
-	"machine_max_acceleration_x": [
-		"5000"
-	],
-	"machine_max_acceleration_y": [
-		"5000"
-	],
-	"machine_max_acceleration_z": [
-		"100"
-	],
-	"machine_max_jerk_e": [
-		"2.5"
-	],
-	"machine_max_jerk_x": [
-		"10"
-	],
-	"machine_max_jerk_y": [
-		"10"
-	],
-	"machine_max_jerk_z": [
-		"0.4"
-	],
-	"machine_max_speed_e": [
-		"60"
-	],
-	"machine_max_speed_x": [
-		"500"
-	],
-	"machine_max_speed_y": [
-		"500"
-	],
-	"machine_max_speed_z": [
-		"20"
-	],
-	"retraction_length": [
-		"2"
-	],
-	"retraction_speed": [
-		"40"
-	],
-	"deretraction_speed": [
-		"40"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"retract_lift_below": [
-		"300"
-	],
-	"machine_start_gcode": "; === IdeaFormer IR3 V2 Belt Printer Start ===\n; Axes: X=lateral, Y=gantry height (probe), Z=belt\nG90 ; absolute positioning\nM82 ; absolute extruder\nG21 ; millimeters\nG28 ; home all axes\nG1 Y20 F500 ; lift nozzle 20mm from belt\n; Bed + hotend temps come from the active filament profile. Belt PLA requires 75 C bed — use Generic/eSun PLA @IdeaFormer IR3 V2 filament presets to get it automatically.\nM140 S[hot_plate_temp_initial_layer] ; set bed temp\nM104 S[nozzle_temperature_initial_layer] ; hotend temp\nM109 S[nozzle_temperature_initial_layer] ; wait hotend\nM190 S[hot_plate_temp_initial_layer] ; wait bed\n; --- Purge blob ---\nG92 E0 ; zero extruder\nG1 Y.1 ; nozzle 0.1mm above belt\nG1 E15 F1000 ; purge 15mm blob\nG1 Z20 E25 F800 ; belt advance 20mm + extrude\nG1 E23 ; retract 2mm\nG28 Y ; re-probe belt surface\nG1 E25 ; de-retract\n; --- Prime lines (full 250mm bed width) ---\nFMS_on ; filament motion sensor\nG1 X250 E50 F2000 ; prime line 1\nG92 Z0 ; reset belt origin\nG1 Z.4 ; belt advance 0.4mm\nG1 X0 E75 ; prime line 2\nG1 F1000 ; default feedrate\nG92 E0 Z0 ; zero extruder + belt = print origin\n",
-	"machine_end_gcode": "; === IdeaFormer IR3 V2 Belt Printer End ===\nM400 ; wait for moves to finish\nM104 S0 ; heater off\nM140 S0 ; bed off\nG92 E0 ; zero extruder\nG1 E-5 F300 ; retract 5mm\nG4 P5000 ; wait for ooze\nG91 ; relative mode - keep every end move relative on a belt\nG1 Y20 F1000 ; raise gantry 20mm for clearance over the part\nG1 Z676 F3000 ; advance belt one full machine-depth to eject the part and clean the belt\nG90 ; back to absolute\nG28 X ; home X only - NEVER 'G28' all: that homes Z/belt and reverses the whole print back into the gantry\nFMS_off ; filament motion sensor off\nBED_MESH_CLEAR\nM84 ; disable motors\n",
-	"machine_pause_gcode": "PAUSE",
-	"layer_change_gcode": "G92 E0 ; belt: reset extruder at layer change (relative E)"
-}

resources/profiles/IdeaFormer/machine/IdeaFormer IR3 V2.json

@@ -1,12 +0,0 @@
-{
-	"type": "machine_model",
-	"name": "IdeaFormer IR3 V2",
-	"model_id": "IdeaFormer_IR3_V2",
-	"nozzle_diameter": "0.4",
-	"machine_tech": "FFF",
-	"family": "IdeaFormer",
-	"bed_model": "",
-	"bed_texture": "",
-	"hotend_model": "",
-	"default_materials": "Generic PLA @IdeaFormer IR3 V2;Generic PETG @IdeaFormer IR3 V2"
-}

resources/profiles/IdeaFormer/machine/fdm_belt_common.json

@@ -1,99 +0,0 @@
-{
-	"type": "machine",
-	"name": "fdm_belt_common",
-	"inherits": "fdm_klipper_common",
-	"from": "system",
-	"instantiation": "false",
-	"gcode_flavor": "klipper",
-	"single_extruder_multi_material": "0",
-	"default_filament_profile": [
-		"Generic PLA @System"
-	],
-	"default_print_profile": "0.20mm Standard @IdeaFormer IR3 V2",
-	"max_layer_height": [
-		"0.32"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"deretraction_speed": [
-		"30"
-	],
-	"extruder_colour": [
-		"#FCE94F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"retract_before_wipe": [
-		"70%"
-	],
-	"retract_length_toolchange": [
-		"2"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"0"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"18"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retraction_speed": [
-		"30"
-	],
-	"travel_slope": [
-		"3"
-	],
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"1"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Normal Lift"
-	],
-	"gcode_remap_x": "rev_x",
-	"gcode_remap_y": "pos_z",
-	"gcode_remap_z": "pos_y",
-	"printer_extruder_id": [
-		"1"
-	],
-	"belt_printer": "1",
-	"belt_slice_rotation": "x",
-	"belt_slice_rotation_angle": "45",
-	"belt_slice_rotation_global": "1",
-	"build_plate_tilt_x": "45",
-	"purge_in_prime_tower": "0",
-	"scan_first_layer": "0",
-	"auxiliary_fan": "0"
-}

resources/profiles/IdeaFormer/machine/fdm_klipper_common.json

@@ -1,141 +0,0 @@
-{
-	"type": "machine",
-	"name": "fdm_klipper_common",
-	"inherits": "fdm_machine_common",
-	"from": "system",
-	"instantiation": "false",
-	"gcode_flavor": "klipper",
-	"machine_max_acceleration_e": [
-		"5000",
-		"5000"
-	],
-	"machine_max_acceleration_extruding": [
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_retracting": [
-		"5000",
-		"5000"
-	],
-	"machine_max_acceleration_travel": [
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_x": [
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_y": [
-		"20000",
-		"20000"
-	],
-	"machine_max_acceleration_z": [
-		"500",
-		"200"
-	],
-	"machine_max_speed_e": [
-		"25",
-		"25"
-	],
-	"machine_max_speed_x": [
-		"500",
-		"200"
-	],
-	"machine_max_speed_y": [
-		"500",
-		"200"
-	],
-	"machine_max_speed_z": [
-		"12",
-		"12"
-	],
-	"machine_max_jerk_e": [
-		"2.5",
-		"2.5"
-	],
-	"machine_max_jerk_x": [
-		"9",
-		"9"
-	],
-	"machine_max_jerk_y": [
-		"9",
-		"9"
-	],
-	"machine_max_jerk_z": [
-		"0.2",
-		"0.4"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0"
-	],
-	"max_layer_height": [
-		"0.32"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"printable_height": "250",
-	"extruder_clearance_radius": "65",
-	"extruder_clearance_height_to_rod": "36",
-	"extruder_clearance_height_to_lid": "140",
-	"printer_settings_id": "",
-	"printer_technology": "FFF",
-	"printer_variant": "0.4",
-	"retraction_minimum_travel": [
-		"1"
-	],
-	"retract_before_wipe": [
-		"70%"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_length": [
-		"0.8"
-	],
-	"retract_length_toolchange": [
-		"2"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retraction_speed": [
-		"30"
-	],
-	"deretraction_speed": [
-		"30"
-	],
-	"z_hop_types": "Normal Lift",
-	"silent_mode": "0",
-	"single_extruder_multi_material": "1",
-	"change_filament_gcode": "",
-	"wipe": [
-		"1"
-	],
-	"default_filament_profile": [
-		"Generic PLA @System"
-	],
-	"default_print_profile": "0.20mm Standard @MyKlipper",
-	"bed_exclude_area": [
-		"0x0"
-	],
-	"machine_start_gcode": "M190 S[bed_temperature_initial_layer_single]\nM109 S[nozzle_temperature_initial_layer]\nPRINT_START EXTRUDER=[nozzle_temperature_initial_layer] BED=[bed_temperature_initial_layer_single]\n",
-	"machine_end_gcode": "PRINT_END",
-	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
-	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
-	"machine_pause_gcode": "PAUSE",
-	"scan_first_layer": "0",
-	"nozzle_type": "undefine",
-	"auxiliary_fan": "0"
-}

resources/profiles/IdeaFormer/machine/fdm_machine_common.json

@@ -1,119 +0,0 @@
-{
-	"type": "machine",
-	"name": "fdm_machine_common",
-	"from": "system",
-	"instantiation": "false",
-	"printer_technology": "FFF",
-	"deretraction_speed": [
-		"40"
-	],
-	"extruder_colour": [
-		"#FCE94F"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"gcode_flavor": "marlin",
-	"silent_mode": "0",
-	"machine_max_acceleration_e": [
-		"5000"
-	],
-	"machine_max_acceleration_extruding": [
-		"10000"
-	],
-	"machine_max_acceleration_retracting": [
-		"1000"
-	],
-	"machine_max_acceleration_x": [
-		"10000"
-	],
-	"machine_max_acceleration_y": [
-		"10000"
-	],
-	"machine_max_acceleration_z": [
-		"500"
-	],
-	"machine_max_speed_e": [
-		"60"
-	],
-	"machine_max_speed_x": [
-		"500"
-	],
-	"machine_max_speed_y": [
-		"500"
-	],
-	"machine_max_speed_z": [
-		"10"
-	],
-	"machine_max_jerk_e": [
-		"5"
-	],
-	"machine_max_jerk_x": [
-		"8"
-	],
-	"machine_max_jerk_y": [
-		"8"
-	],
-	"machine_max_jerk_z": [
-		"0.4"
-	],
-	"machine_min_extruding_rate": [
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0"
-	],
-	"max_layer_height": [
-		"0.32"
-	],
-	"min_layer_height": [
-		"0.08"
-	],
-	"printable_height": "250",
-	"extruder_clearance_radius": "65",
-	"extruder_clearance_height_to_rod": "36",
-	"extruder_clearance_height_to_lid": "140",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"printer_settings_id": "",
-	"printer_variant": "0.4",
-	"retraction_minimum_travel": [
-		"2"
-	],
-	"retract_before_wipe": [
-		"70%"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_length": [
-		"1"
-	],
-	"retract_length_toolchange": [
-		"1"
-	],
-	"z_hop": [
-		"0"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retraction_speed": [
-		"60"
-	],
-	"single_extruder_multi_material": "1",
-	"change_filament_gcode": "",
-	"wipe": [
-		"1"
-	],
-	"default_print_profile": "",
-	"machine_start_gcode": "G0 Z20 F9000\nG92 E0; G1 E-10 F1200\nG28\nM970 Q1 A10 B10 C130 K0\nM970 Q1 A10 B131 C250 K1\nM974 Q1 S1 P0\nM970 Q0 A10 B10 C130 H20 K0\nM970 Q0 A10 B131 C250 K1\nM974 Q0 S1 P0\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG29 ;Home\nG90;\nG92 E0 ;Reset Extruder \nG1 Z2.0 F3000 ;Move Z Axis up \nG1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position\nM109 S205;\nG1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little\nG1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line\nG92 E0 ;Reset Extruder \nG1 X110 Y110 Z2.0 F3000 ;Move Z Axis up",
-	"machine_end_gcode": "M400 ; wait for buffer to clear\nG92 E0 ; zero the extruder\nG1 E-4.0 F3600; retract \nG91\nG1 Z3;\nM104 S0 ; turn off hotend\nM140 S0 ; turn off bed\nM106 S0 ; turn off fan\nG90 \nG0 X110 Y200 F3600 \nprint_end",
-	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
-	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
-	"machine_pause_gcode": "M601"
-}

resources/profiles/IdeaFormer/process/0.20mm Standard @IdeaFormer IR3 V2.json

@@ -1,23 +0,0 @@
-{
-	"type": "process",
-	"name": "0.20mm Standard @IdeaFormer IR3 V2",
-	"inherits": "fdm_process_common",
-	"from": "system",
-	"setting_id": "91atcIwv5728phqX",
-	"instantiation": "true",
-	"layer_height": "0.2",
-	"initial_layer_print_height": "0.2",
-	"initial_layer_line_width": "0.42",
-	"wall_loops": "2",
-	"reduce_infill_retraction": "1",
-	"detect_overhang_wall": "1",
-	"skirt_loops": "0",
-	"skirt_distance": "0",
-	"sparse_infill_pattern": "grid",
-	"sparse_infill_speed": "200",
-	"support_base_pattern": "rectilinear",
-	"support_interface_pattern": "rectilinear",
-	"compatible_printers": [
-		"IdeaFormer IR3 V2 0.4 nozzle"
-	]
-}

resources/profiles/IdeaFormer/process/fdm_process_common.json

@@ -1,108 +0,0 @@
-{
-	"type": "process",
-	"name": "fdm_process_common",
-	"from": "system",
-	"instantiation": "false",
-	"adaptive_layer_height": "0",
-	"reduce_crossing_wall": "0",
-	"max_travel_detour_distance": "0",
-	"bottom_surface_pattern": "monotonic",
-	"bottom_shell_thickness": "0",
-	"bridge_speed": "50",
-	"brim_width": "5",
-	"brim_object_gap": "0.1",
-	"compatible_printers": [],
-	"compatible_printers_condition": "",
-	"print_sequence": "by layer",
-	"default_acceleration": "1000",
-	"initial_layer_acceleration": "500",
-	"top_surface_acceleration": "1000",
-	"travel_acceleration": "1000",
-	"inner_wall_acceleration": "1000",
-	"outer_wall_acceleration": "700",
-	"bridge_no_support": "0",
-	"draft_shield": "disabled",
-	"elefant_foot_compensation": "0",
-	"enable_arc_fitting": "0",
-	"wall_infill_order": "inner wall/outer wall/infill",
-	"infill_direction": "45",
-	"sparse_infill_density": "15%",
-	"sparse_infill_pattern": "crosshatch",
-	"initial_layer_print_height": "0.2",
-	"infill_combination": "0",
-	"infill_wall_overlap": "25%",
-	"interface_shells": "0",
-	"ironing_flow": "10%",
-	"ironing_spacing": "0.15",
-	"ironing_speed": "30",
-	"ironing_type": "no ironing",
-	"reduce_infill_retraction": "1",
-	"filename_format": "{input_filename_base}_{layer_height}mm_{filament_type[initial_tool]}_{printer_model}_{print_time}.gcode",
-	"detect_overhang_wall": "1",
-	"slowdown_for_curled_perimeters": "1",
-	"overhang_1_4_speed": "0",
-	"overhang_2_4_speed": "50",
-	"overhang_3_4_speed": "30",
-	"overhang_4_4_speed": "10",
-	"line_width": "110%",
-	"inner_wall_line_width": "110%",
-	"outer_wall_line_width": "100%",
-	"top_surface_line_width": "93.75%",
-	"sparse_infill_line_width": "110%",
-	"initial_layer_line_width": "120%",
-	"internal_solid_infill_line_width": "120%",
-	"support_line_width": "96%",
-	"wall_loops": "3",
-	"print_settings_id": "",
-	"raft_layers": "0",
-	"seam_position": "aligned",
-	"skirt_distance": "2",
-	"skirt_height": "3",
-	"min_skirt_length": "4",
-	"skirt_loops": "0",
-	"minimum_sparse_infill_area": "15",
-	"spiral_mode": "0",
-	"standby_temperature_delta": "-5",
-	"enable_support": "0",
-	"resolution": "0.012",
-	"support_type": "normal(auto)",
-	"support_on_build_plate_only": "0",
-	"support_top_z_distance": "0.2",
-	"support_bottom_z_distance": "0.2",
-	"support_filament": "0",
-	"support_interface_loop_pattern": "0",
-	"support_interface_filament": "0",
-	"support_interface_top_layers": "2",
-	"support_interface_bottom_layers": "2",
-	"support_interface_spacing": "0.5",
-	"support_interface_speed": "80",
-	"support_base_pattern": "default",
-	"support_base_pattern_spacing": "2.5",
-	"support_speed": "150",
-	"support_threshold_angle": "30",
-	"support_object_xy_distance": "0.35",
-	"tree_support_branch_angle": "30",
-	"tree_support_wall_count": "0",
-	"tree_support_with_infill": "0",
-	"detect_thin_wall": "0",
-	"top_surface_pattern": "monotonicline",
-	"top_shell_thickness": "0.8",
-	"enable_prime_tower": "1",
-	"wipe_tower_no_sparse_layers": "0",
-	"prime_tower_width": "60",
-	"xy_hole_compensation": "0",
-	"xy_contour_compensation": "0",
-	"layer_height": "0.2",
-	"bottom_shell_layers": "3",
-	"top_shell_layers": "4",
-	"bridge_flow": "1",
-	"initial_layer_speed": "45",
-	"initial_layer_infill_speed": "45",
-	"outer_wall_speed": "45",
-	"inner_wall_speed": "80",
-	"sparse_infill_speed": "150",
-	"internal_solid_infill_speed": "150",
-	"top_surface_speed": "50",
-	"gap_infill_speed": "30",
-	"travel_speed": "200"
-}

resources/profiles/OrcaFilamentLibrary.json

@@ -1,6 +1,6 @@
 {
 	"name": "OrcaFilamentLibrary",
-	"version": "02.04.00.03",
+	"version": "02.04.00.04",
 	"force_update": "0",
 	"description": "Orca Filament Library",
 	"filament_list": [

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu PET-CF @base.json

@@ -36,6 +36,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_type": [
 		"PET-CF"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu PETG Basic @base.json

@@ -39,6 +39,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_vendor": [
 		"Bambu Lab"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu PETG Translucent @base.json

@@ -39,6 +39,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_vendor": [
 		"Bambu Lab"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu PLA Aero @base.json

@@ -21,6 +21,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_type": [
 		"PLA-AERO"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu Support For PLA-PETG @base.json

@@ -27,6 +27,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_scarf_seam_type": [
 		"none"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Bambu/Bambu Support for ABS @base.json

@@ -21,6 +21,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_vendor": [
 		"Bambu Lab"
 	],

resources/profiles/OrcaFilamentLibrary/filament/COEX/COEX TPU 60A @base.json

@@ -36,6 +36,9 @@
 	"filament_max_volumetric_speed": [
 		"1"
 	],
+	"filament_multitool_ramming_flow": [
+		"1"
+	],
 	"filament_retraction_minimum_travel": [
 		"3"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elas/Elas ASA @base.json

@@ -72,15 +72,6 @@
 	"fan_min_speed": [
 		"10"
 	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
 	"filament_cost": [
 		"599"
 	],
@@ -99,30 +90,12 @@
 	"filament_is_support": [
 		"0"
 	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
 	"filament_long_retractions_when_cut": [
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
 		"15"
 	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"0"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"10"
-	],
-	"filament_multitool_ramming_volume": [
-		"10"
-	],
 	"filament_notes": [
 		""
 	],
@@ -165,21 +138,6 @@
 	"filament_soluble": [
 		"0"
 	],
-	"filament_stamping_distance": [
-		"0"
-	],
-	"filament_stamping_loading_speed": [
-		"0"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
 	"filament_vendor": [
 		"Elas"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elas/Elas PETG Basic @base.json

@@ -42,15 +42,6 @@
 	"fan_min_speed": [
 		"20"
 	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
 	"filament_cost": [
 		"445"
 	],
@@ -69,30 +60,12 @@
 	"filament_is_support": [
 		"0"
 	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
 	"filament_long_retractions_when_cut": [
 		"1"
 	],
 	"filament_max_volumetric_speed": [
 		"18"
 	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"0"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"10"
-	],
-	"filament_multitool_ramming_volume": [
-		"10"
-	],
 	"filament_notes": [
 		""
 	],
@@ -135,21 +108,6 @@
 	"filament_soluble": [
 		"0"
 	],
-	"filament_stamping_distance": [
-		"0"
-	],
-	"filament_stamping_loading_speed": [
-		"0"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
 	"filament_wipe": [
 		"nil"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elas/Elas PLA Basic @base.json

@@ -71,15 +71,6 @@
 	"fan_min_speed": [
 		"60"
 	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
 	"filament_cost": [
 		"449.5"
 	],
@@ -98,30 +89,12 @@
 	"filament_is_support": [
 		"0"
 	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
 	"filament_long_retractions_when_cut": [
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
 		"25"
 	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"0"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"10"
-	],
-	"filament_multitool_ramming_volume": [
-		"10"
-	],
 	"filament_notes": [
 		""
 	],
@@ -164,21 +137,6 @@
 	"filament_soluble": [
 		"0"
 	],
-	"filament_stamping_distance": [
-		"0"
-	],
-	"filament_stamping_loading_speed": [
-		"0"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
 	"filament_vendor": [
 		"Elas"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elas/Elas PLA Pro @base.json

@@ -71,15 +71,6 @@
 	"fan_min_speed": [
 		"100"
 	],
-	"filament_cooling_final_speed": [
-		"0"
-	],
-	"filament_cooling_initial_speed": [
-		"0"
-	],
-	"filament_cooling_moves": [
-		"0"
-	],
 	"filament_cost": [
 		"500"
 	],
@@ -98,30 +89,12 @@
 	"filament_is_support": [
 		"0"
 	],
-	"filament_loading_speed": [
-		"0"
-	],
-	"filament_loading_speed_start": [
-		"0"
-	],
 	"filament_long_retractions_when_cut": [
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
 		"18"
 	],
-	"filament_minimal_purge_on_wipe_tower": [
-		"0"
-	],
-	"filament_multitool_ramming": [
-		"0"
-	],
-	"filament_multitool_ramming_flow": [
-		"10"
-	],
-	"filament_multitool_ramming_volume": [
-		"10"
-	],
 	"filament_notes": [
 		""
 	],
@@ -164,21 +137,6 @@
 	"filament_soluble": [
 		"0"
 	],
-	"filament_stamping_distance": [
-		"0"
-	],
-	"filament_stamping_loading_speed": [
-		"0"
-	],
-	"filament_toolchange_delay": [
-		"0"
-	],
-	"filament_unloading_speed": [
-		"0"
-	],
-	"filament_unloading_speed_start": [
-		"0"
-	],
 	"filament_vendor": [
 		"Elas"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elegoo/Elegoo PAHT-CF @System.json

@@ -24,6 +24,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"nozzle_temperature": [
 		"290"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elegoo/Elegoo PETG @base.json

@@ -35,6 +35,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_vendor": [
 		"Elegoo"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Elegoo/Elegoo PLA Wood @System.json

@@ -12,6 +12,9 @@
 	"filament_max_volumetric_speed": [
 		"10"
 	],
+	"filament_multitool_ramming_flow": [
+		"10"
+	],
 	"nozzle_temperature": [
 		"220"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Eolas Prints/Eolas Prints PLA Neon @System.json

@@ -44,5 +44,8 @@
 	],
 	"filament_max_volumetric_speed": [
 		"10"
+	],
+	"filament_multitool_ramming_flow": [
+		"10"
 	]
 }

resources/profiles/OrcaFilamentLibrary/filament/Eolas Prints/Eolas Prints PLA Silk @System.json

@@ -44,5 +44,8 @@
 	],
 	"filament_max_volumetric_speed": [
 		"8"
+	],
+	"filament_multitool_ramming_flow": [
+		"8"
 	]
 }

resources/profiles/OrcaFilamentLibrary/filament/Generic PA-CF @System.json

@@ -10,5 +10,8 @@
 	"filament_type": [
 		"PA-CF"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"compatible_printers": []
 }

resources/profiles/OrcaFilamentLibrary/filament/Generic PETG HF @System.json

@@ -8,5 +8,8 @@
 	"filament_max_volumetric_speed": [
 		"20"
 	],
+	"filament_multitool_ramming_flow": [
+		"20"
+	],
 	"compatible_printers": []
 }

resources/profiles/OrcaFilamentLibrary/filament/Generic PETG-CF @System.json

@@ -17,6 +17,9 @@
 	"filament_max_volumetric_speed": [
 		"11.5"
 	],
+	"filament_multitool_ramming_flow": [
+		"13"
+	],
 	"overhang_fan_speed": [
 		"100"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Generic PLA High Speed @System.json

@@ -12,6 +12,9 @@
 	"filament_max_volumetric_speed": [
 		"18"
 	],
+	"filament_multitool_ramming_flow": [
+		"25"
+	],
 	"slow_down_layer_time": [
 		"4"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Generic PLA Matte @System.json

@@ -8,6 +8,9 @@
 	"filament_max_volumetric_speed": [
 		"11"
 	],
+	"filament_multitool_ramming_flow": [
+		"11"
+	],
 	"filament_retraction_length": [
 		"0.8"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Generic PP-CF @System.json

@@ -15,6 +15,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_type": [
 		"PP-CF"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Generic PP-GF @System.json

@@ -15,6 +15,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_type": [
 		"PP-GF"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Overture/Overture Air PLA @base.json

@@ -17,6 +17,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_vendor": [
 		"Overture"
 	],

resources/profiles/OrcaFilamentLibrary/filament/Valment/Valment PLA Silk @base.json

@@ -23,6 +23,9 @@
 	"filament_max_volumetric_speed": [
 		"7.5"
 	],
+	"filament_multitool_ramming_flow": [
+		"7.5"
+	],
 	"filament_vendor": [
 		"Valment"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_abs.json

@@ -43,6 +43,12 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"15"
+	],
+	"filament_multitool_ramming_volume": [
+		"10"
+	],
 	"filament_type": [
 		"ABS"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_asa.json

@@ -43,6 +43,12 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
+	"filament_multitool_ramming_volume": [
+		"10"
+	],
 	"filament_type": [
 		"ASA"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_bvoh.json

@@ -41,6 +41,15 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming": [
+		"0"
+	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
+	"filament_multitool_ramming_volume": [
+		"0.1"
+	],
 	"filament_type": [
 		"BVOH"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_common.json

@@ -66,6 +66,12 @@
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
 	],
+	"filament_multitool_ramming": [
+		"1"
+	],
+	"filament_multitool_ramming_volume": [
+		"5"
+	],
 	"filament_retract_before_wipe": [
 		"nil"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_cope.json

@@ -41,6 +41,9 @@
 	"filament_max_volumetric_speed": [
 		"16"
 	],
+	"filament_multitool_ramming_flow": [
+		"16"
+	],
 	"filament_scarf_seam_type": [
 		"none"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_eva.json

@@ -8,6 +8,9 @@
 	"filament_type": [
 		"EVA"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"supertack_plate_temp": [
 		"0"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_hips.json

@@ -41,6 +41,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_type": [
 		"HIPS"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pa.json

@@ -44,6 +44,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"filament_type": [
 		"PA"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_paht.json

@@ -7,6 +7,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"filament_type": [
 		"PAHT"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pc.json

@@ -86,6 +86,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"16"
+	],
 	"filament_flow_ratio": [
 		"0.94"
 	]

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pctg.json

@@ -26,6 +26,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"10"
+	],
 	"filament_type": [
 		"PCTG"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pe.json

@@ -38,6 +38,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"filament_type": [
 		"PE"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pet.json

@@ -26,6 +26,9 @@
 	"filament_max_volumetric_speed": [
 		"10"
 	],
+	"filament_multitool_ramming_flow": [
+		"15"
+	],
 	"filament_type": [
 		"PETG"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pha.json

@@ -38,6 +38,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_type": [
 		"PHA"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pla.json

@@ -38,6 +38,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"20"
+	],
 	"filament_scarf_seam_type": [
 		"none"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pla_silk.json

@@ -9,6 +9,9 @@
 	"filament_flow_ratio": [
 		"0.98"
 	],
+	"filament_multitool_ramming_flow": [
+		"10"
+	],
 	"slow_down_layer_time": [
 		"8"
 	]

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pp.json

@@ -38,6 +38,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"filament_type": [
 		"PP"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_ppa.json

@@ -47,6 +47,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_type": [
 		"PPA-CF"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pps.json

@@ -43,6 +43,9 @@
 	"filament_max_volumetric_speed": [
 		"4"
 	],
+	"filament_multitool_ramming_flow": [
+		"4"
+	],
 	"filament_type": [
 		"PPS"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_pva.json

@@ -40,6 +40,15 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming": [
+		"0"
+	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
+	"filament_multitool_ramming_volume": [
+		"0.1"
+	],
 	"filament_soluble": [
 		"1"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_sbs.json

@@ -11,6 +11,9 @@
 	"filament_max_volumetric_speed": [
 		"12"
 	],
+	"filament_multitool_ramming_flow": [
+		"12"
+	],
 	"filament_type": [
 		"SBS"
 	],

resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_tpu.json

@@ -43,6 +43,15 @@
 	"filament_max_volumetric_speed": [
 		"3.2"
 	],
+	"filament_multitool_ramming": [
+		"0"
+	],
+	"filament_multitool_ramming_flow": [
+		"3.2"
+	],
+	"filament_multitool_ramming_volume": [
+		"0.1"
+	],
 	"filament_retraction_length": [
 		"0.4"
 	],

resources/profiles/OrcaFilamentLibrary/filament/eSUN/eSUN PLA-Marble @base.json

@@ -17,6 +17,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_vendor": [
 		"eSUN"
 	],

resources/profiles/OrcaFilamentLibrary/filament/eSUN/eSUN PLA-Matte @base.json

@@ -17,6 +17,9 @@
 	"filament_max_volumetric_speed": [
 		"8"
 	],
+	"filament_multitool_ramming_flow": [
+		"8"
+	],
 	"filament_vendor": [
 		"eSUN"
 	],

resources/profiles/OrcaFilamentLibrary/filament/eSUN/eSUN ePLA-LW @System.json

@@ -21,6 +21,9 @@
 	"filament_max_volumetric_speed": [
 		"6"
 	],
+	"filament_multitool_ramming_flow": [
+		"6"
+	],
 	"filament_vendor": [
 		"eSUN"
 	],

resources/profiles/Printcepts.json

@@ -1,54 +0,0 @@
-{
-	"name": "Printcepts",
-	"version": "01.00.00.01",
-	"force_update": "0",
-	"description": "Printcepts belt printer configurations",
-	"machine_model_list": [
-		{
-			"name": "BabyBelt Pro",
-			"sub_path": "machine/BabyBelt Pro.json"
-		}
-	],
-	"process_list": [
-		{
-			"name": "fdm_process_common",
-			"sub_path": "process/fdm_process_common.json"
-		},
-		{
-			"name": "0.20mm Standard @BabyBelt Pro",
-			"sub_path": "process/0.20mm Standard @BabyBelt Pro.json"
-		}
-	],
-	"filament_list": [
-		{
-			"name": "Generic PLA @BabyBelt Pro",
-			"sub_path": "filament/Generic PLA @BabyBelt Pro.json"
-		},
-		{
-			"name": "eSUN PLA @BabyBelt Pro",
-			"sub_path": "filament/eSUN PLA @BabyBelt Pro.json"
-		},
-		{
-			"name": "Generic PETG @BabyBelt Pro",
-			"sub_path": "filament/Generic PETG @BabyBelt Pro.json"
-		}
-	],
-	"machine_list": [
-		{
-			"name": "fdm_machine_common",
-			"sub_path": "machine/fdm_machine_common.json"
-		},
-		{
-			"name": "fdm_klipper_common",
-			"sub_path": "machine/fdm_klipper_common.json"
-		},
-		{
-			"name": "fdm_belt_common",
-			"sub_path": "machine/fdm_belt_common.json"
-		},
-		{
-			"name": "BabyBelt Pro 0.4 nozzle",
-			"sub_path": "machine/BabyBelt Pro 0.4 nozzle.json"
-		}
-	]
-}

resources/profiles/Printcepts/BabyBelt Pro_bed_texture.svg

@@ -1,70 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" width="95.0mm" height="500.0mm" viewBox="0 0 95.0 500.0" preserveAspectRatio="xMidYMid meet">
-  <!-- Printcepts BabyBelt Pro bed texture: 95 x 500 mm belt plate. -->
-  <!-- Transparent plate; green (#195F30) BabyBelt Pro logo centered along X, near the bottom edge. -->
-  <rect x="0" y="0" width="95.0" height="500.0" fill="none"/>
-  <g transform="translate(14.2500,436.3488) scale(0.067538)">
-    <g transform="translate(-11.000000,692.938562) scale(0.100000,-0.100000)"
-fill="#195F30" stroke="none">
-<path d="M1963 5604 l-1423 -1324 0 -2050 0 -2050 443 0 c244 0 741 3 1105 7
-l662 6 0 746 c-1 575 -4 768 -14 841 -47 324 -179 486 -473 581 -40 12 -73 26
--73 30 0 4 32 17 72 29 212 64 333 166 378 320 35 121 38 191 32 868 l-5 662
--629 0 c-395 0 -628 4 -628 10 0 5 635 601 1410 1325 776 724 1410 1318 1410
-1321 0 2 -190 4 -422 3 l-423 0 -1422 -1325z m-334 -2029 c143 -16 174 -96
-173 -446 -2 -411 -24 -458 -224 -462 l-93 -2 -3 450 c-1 248 0 456 3 463 3 9
-18 12 47 8 24 -3 67 -8 97 -11z m-4 -1556 c160 -29 173 -62 182 -469 9 -455
--14 -593 -108 -641 -39 -19 -193 -44 -210 -33 -10 6 -13 1147 -3 1157 6 6 45
-2 139 -14z"/>
-<path d="M3464 5979 c-142 -132 -263 -245 -268 -250 -6 -5 69 -9 190 -9 l199
-1 268 249 267 250 -198 0 -198 0 -260 -241z"/>
-<path d="M3650 5649 c-135 -126 -254 -238 -265 -249 -19 -20 -18 -20 177 -20
-l197 0 228 211 c125 116 246 229 268 250 l40 39 -200 -1 -200 0 -245 -230z"/>
-<path d="M2537 5089 c-101 -24 -204 -105 -251 -197 -96 -190 -19 -420 172
--514 l67 -33 2670 0 2670 0 57 27 c74 34 146 107 184 183 43 88 43 230 0 322
--35 76 -113 153 -193 191 l-58 27 -2640 2 c-1513 0 -2656 -3 -2678 -8z m5063
--77 c-57 -37 -118 -111 -140 -168 -31 -82 -25 -206 12 -279 26 -49 93 -121
-133 -143 15 -8 -640 -11 -2410 -11 l-2430 0 30 21 c200 146 201 425 1 569
-l-39 29 2434 -1 c2263 0 2432 -1 2409 -17z m-4890 -43 c270 -122 185 -526
--109 -522 -257 2 -370 324 -170 485 74 60 194 76 279 37z m5201 -12 c94 -55
-140 -135 140 -242 0 -285 -393 -374 -517 -117 -26 54 -30 162 -9 219 28 74 97
-139 173 164 53 17 166 4 213 -24z"/>
-<path d="M2917 3973 c-4 -174 -7 -550 -7 -835 l0 -518 326 0 326 0 -7 150 -7
-150 110 0 110 0 11 -32 c5 -18 26 -86 46 -150 l36 -118 325 0 c179 0 323 4
-320 9 -3 4 -155 374 -337 822 -182 448 -333 820 -336 827 -4 9 -105 12 -457
-12 l-453 0 -6 -317z m773 -745 c0 -5 -47 -8 -104 -8 l-103 0 -7 92 c-3 50 -6
-202 -5 337 l1 246 109 -330 c60 -181 109 -333 109 -337z"/>
-<path d="M4680 3455 l0 -835 448 0 c693 1 885 16 985 80 99 63 126 132 134
-340 12 327 -44 405 -342 476 -28 7 -27 8 25 19 199 42 255 95 267 248 11 146
--32 285 -110 353 -145 126 -329 153 -1049 154 l-358 0 0 -835z m846 520 c36
--23 44 -54 44 -162 0 -152 -29 -183 -170 -183 l-40 0 0 186 0 187 71 -6 c39
--3 82 -13 95 -22z m4 -625 c33 -18 40 -52 40 -208 0 -200 -9 -214 -143 -228
-l-67 -7 0 233 0 233 74 -6 c41 -3 84 -10 96 -17z"/>
-<path d="M6150 4286 c0 -3 131 -242 290 -531 l290 -526 0 -304 0 -305 385 0
-385 0 0 299 0 299 305 533 305 534 -377 3 c-207 1 -381 -2 -385 -6 -16 -16
--110 -258 -172 -444 l-62 -187 -18 77 c-18 75 -139 450 -171 525 l-15 37 -380
-0 c-209 0 -380 -2 -380 -4z"/>
-<path d="M2910 1355 l0 -1185 830 0 830 0 0 240 0 240 -350 0 -350 0 0 255 0
-255 300 0 300 0 0 230 0 230 -300 0 -300 0 0 220 0 220 320 0 320 0 0 240 0
-240 -800 0 -800 0 0 -1185z"/>
-<path d="M4680 1355 l0 -1185 775 0 775 0 0 240 0 240 -295 0 -295 0 0 945 0
-945 -480 0 -480 0 0 -1185z"/>
-<path d="M5800 2300 l0 -240 280 0 280 0 0 -945 0 -945 480 0 480 0 0 945 0
-945 285 0 285 0 0 240 0 240 -1045 0 -1045 0 0 -240z"/>
-<path d="M8032 1358 l-2 -1188 1008 1 c621 1 971 5 912 10 -309 27 -631 139
--885 306 -593 391 -984 1122 -1025 1918 -4 77 -8 -394 -8 -1047z"/>
-<path d="M7441 1934 c-43 -36 -59 -70 -70 -148 -18 -124 16 -252 76 -291 32
--21 226 -33 328 -20 114 14 161 97 153 269 -5 96 -24 151 -68 191 -20 18 -39
-20 -205 23 l-182 3 -32 -27z m389 -199 c7 -8 10 -22 6 -30 -4 -13 -34 -15
--186 -15 -189 0 -202 3 -186 45 8 22 348 22 366 0z"/>
-<path d="M7450 1267 c-14 -6 -35 -32 -47 -57 -21 -41 -23 -58 -23 -222 l0
--178 270 0 270 0 0 105 0 105 -121 0 -120 0 3 28 3 27 118 3 117 3 0 99 0 100
--113 0 c-121 0 -138 -7 -162 -65 -8 -19 -9 -19 -12 2 -10 55 -116 84 -183 50z
-m134 -203 c15 -38 8 -44 -54 -44 -62 0 -69 6 -54 44 9 23 99 23 108 0z"/>
-<path d="M466 1193 l-29 -43 -163 0 -164 0 0 -235 0 -235 165 0 165 0 27 -42
-28 -42 3 163 c1 89 1 233 0 319 l-3 157 -29 -42z"/>
-<path d="M7443 620 c-48 -20 -58 -60 -61 -262 l-4 -188 271 0 271 0 0 110 0
-110 -110 0 -110 0 0 70 c0 76 -21 145 -51 160 -22 12 -176 12 -206 0z m161
--186 c15 -39 8 -44 -64 -44 -72 0 -79 5 -64 44 9 23 119 23 128 0z"/>
-</g>
-  </g>
-</svg>