Code review items (raistlin7447):
1. PrintObject::slice() zeroes m_belt_min_z, m_belt_global_z_offset and
m_belt_global_xy_correction before slicing. They were only written in belt
mode, so a project switched to a normal printer, or whose tilt axis was set
to None, kept the old offsets and shifted the adaptive infill octree and the
organic support layers by them.
2. TreeModelVolumes shifts the support blockers into the raft-offset index
space; a test now pins the index the blocker lands on.
3. The final-alignment clamp in libnest2d is opt-in (NfpPConfig::clamp_to_bin)
and arrange sets it for belt printers only. Printers with an off-centre
best_object_pos keep their alignment; a flat-bed test pins that.
4. The preview's belt view follows the loaded G-code, not the selected printer:
GCodeProcessor carries the file's belt keys (and, for a belt file, its bed)
into export_config_for_render(), and GCodeViewer enables the belt view from
the header tilt.
5. belt_shift_layer_grid() also shifts the cached belt floor and the global Z
offset, so a support-only or brim-only change after the purge-prism snap
matches a fresh slice.
6. update_print_fff_config() resets raft_layers and draft_shield on a belt
printer instead of only greying out the fields Print::validate() rejects.
7. GCodeWriter takes a first-layer point test instead of the FirstLayerPlane;
GCode installs one that measures from the belt surface, like its
extrusions, so the first-layer travel speed and the second-layer
temperature change no longer depend on the gcode_remap_* convention.
8. belt_brim_clip_leading_edge() is exported and called by both the generator
and the test.
9. Both phong.vs shaders use slope.up_direction for the overhang highlight.
The pre-slice and G-code axis remaps are gated on belt_printer through
BeltTransformPipeline::axis_remap_enabled(), so belt keys left in a profile
cannot change a non-belt print.
Tests requested in the review: belt-only keys at non-default values leave
non-belt G-code unchanged; switching a sliced project from belt to non-belt
(and tilt axis None) matches a fresh slice; a support-only change on a belt
purge print matches a fresh slice; non-belt start G-code moves keep the
first-layer Z in the processor; the belt brim's segment count catches a band
emitted twice.
The belt-to-non-belt test exposed an unrelated gap: invalidate_step(posSlice)
re-invalidated posSupportMaterial but not posSimplifySupportPath, so after
any re-slice the regenerated support paths were exported unsimplified.
posSimplifySupportPath is now in that list.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
The clang-tidy job on #14394 fails on 129 misc-include-cleaner findings:
the belt sources and tests use std::, Eigen, Point/PrintConfig and
BeltBrim symbols without including the header that provides them, which
only compiled because the precompiled header supplied it. Every include
the job names is added, in each file's existing include style ("../" in
the GCode/ and Support/ subdirectories, quoted libslic3r/ paths in the
GUI and tests). No code changes.
Verified with scripts/clang_tidy_diff.py -p build-tidy --base eb5b9a77b9
(SLIC3R_PCH=OFF compile database, clang-tidy 22.1.8): no findings left.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01L6Kg5igmmMU2YLoK6HrsWV
* Remove Unused Project Includes and Forward-Declare Where a Type Is Only Referenced
Generated with include-what-you-use and applied conservatively. Only OrcaSlicer's own headers, the ones under src/ and tests/, are removed or forward-declared; standard-library and third-party includes are left alone. An include is removed only when both the Release and the Debug configuration leave it unused, never from inside a conditional block, and never from a file with platform-specific blocks, which only gain includes. Files whose only use of a header sits behind a feature or debug macro (libvgcode's OpenGL ES and marker code, the ARACHNE/TESTS_EXPORT_SVGS debug output) keep their includes.
clonable_ptr.hpp gains #pragma once; it had no include guard and was only safe while Config.hpp was its sole includer.
* Remove Unused Project Includes From Files With Platform-Specific Code
A Linux include-what-you-use run cannot see the code inside _WIN32, __APPLE__ or __linux__ blocks, so its verdict is only taken where nothing the removed header declares, directly or through what it includes, is named inside those blocks. Removals also have to hold in both the Release and Debug configuration and never touch a line inside a conditional block.
* Restore the libslic3r Precompiled Header and Direct Includes Lost in the Platform Pass
The platform-file pass treated pchheader.hpp as an ordinary header and
emptied it, and left GUI_Preview.hpp and 14 other files relying on
headers they no longer reached directly.
* Restore MainFrame.hpp in ParamsDialog.cpp for the Windows-Only Reparent Call
* Include Headers That Files Reached Through Ones the Cleanup Removed
* Drop Includes Duplicated by the Cleanup or by Main's Own Additions
* Leave PreciseSeam.cpp as Main Has It After the Precise Seam Rework
Brings belt-printer up to main 4b4a261787. Resolutions:
- G-code header (#15897, #15915): main moved the header, config and
thumbnail block later in _do_export; write_belt_header() moves with it,
still after the thumbnails and outside the BTT_TFT gate.
- _extrude: first-layer acceleration keeps the per-path first-layer plane
test with main's cached nozzle index (#16028); main's set_speed out-param
form (#16108) everywhere else.
- GCodeWriter (#16108): the arc-to-polyline fallback for machine mappings
that cannot express G2/G3 now runs in the out-param extrude_arc_to_xy,
which is the overload GCode calls, and appends to the caller's string.
- GCodeProcessorResult: the belt fields join main's forwarding assign.
- Clipper2 (#15969): belt arrange helpers take Slic3r::Point; the tree
support join types lose their ClipperLib qualifier.
- CLI arrange (#15837): belt printers still reserve no wipe tower.
- Wipe tower options (#15841): the two new sparse-layer toggles are hidden
for belt printers like the rest of the tower options.
- Keyboard shortcuts (#15706): main's registry replaces the old key switch;
the belt view toggle is re-registered in the next commit.
- Print::process: the belt purge-plan undo runs before main's SliceStarted
event.
- scripts/filament_id_snapshot.json: deleted on main (a77209af8f).
- Includes and appended tests: union of both sides.
* Add Missing Includes Across src/libslic3r
Every libslic3r source and header now directly includes the headers declaring what it uses, rather than relying on the precompiled header or transitive includes. Generated with clang-tidy misc-include-cleaner, with libslic3r headers spelled libslic3r/... so they resolve outside the library's private include paths. MultiMaterialSegmentation.hpp, Support/SupportParameters.hpp and Format/STEP.hpp are made self-contained by hand.
* Make the libslic3r Headers Compile on Their Own
Each now includes, or forward-declares, what it uses instead of relying on what its includers happened to include first. Left out: I18N.hpp, which errors on purpose when included from GUI code, and VoxelizeCSGMesh.hpp and SLA/bicubic.h, which nothing includes and which no longer compile at all.
* Add the Includes Missing From the Hand-Fixed libslic3r Headers
clang-tidy would not edit these headers while they failed to compile on their own, so the first pass skipped them. With the headers now self-contained, a second pass adds the rest.
* Keep Windows Setup Ahead of the Added libslic3r Includes
Print.cpp and Thread.cpp open with a _WIN32 block that has to come first; without the precompiled header, Print.cpp otherwise reaches windows.h through OCCT with NONLS defined and boost/regex fails. OpenVDBUtils.cpp and SLA/SupportTreeBuilder.cpp had includes inside #ifndef NOMINMAX, which libslic3r defines on Windows, so those were skipped there. .clang-tidy also ignores the MSVC STL and UCRT internals, Boost.Multiprecision's fwd.hpp and CPython's Windows include directory.
* Re-Add libslic3r Includes After the Clipper2 2.0.1 Migration
Rebasing onto main took main's version of the files the Clipper2 migration rewrote, so their added includes are restored here, along with includes for main's new code. Clipper2's individual headers are now ignored by clang-tidy: they only build the Z variant through clipper2_z.hpp, which defines USINGZ first, so including clipper.core.h and the like directly broke ClipperZUtils.cpp.
Brings in upstream/belt-printer (the Sept 14 main merge) plus Hanif Koh's
21 review-fix commits from PR #15685, on top of the MachineKinematics
refactor and the purge-prism / tree-support / first-layer-speed fixes.
Conflict resolution:
- BeltGCodeWriter is gone (kinematics refactor), so Hanif's plate-offset
fix for it is ported into GCodeWriter: the first-layer-plane checks in
travel_to_xy / travel_to_xyz / _travel_to_z now evaluate the plate-local
point, and BeltGCode::init_belt_writer hands the stored plate origin to
the writer it installs.
- init_belt_writer(Print&) takes Hanif's signature; the BBL flag is set on
the surviving writer by GCode::_do_export.
- The shared emit_belt_brim_bands() loop keeps the BeltFloorObjectGuard the
local branch added, so apron bands classify first-layer height against
their own object.
- eager_lift keeps effective_type: it now carries set_force_normal_lift().
- GCodeWriter's initializer list follows Hanif's member order with
m_kinematics in its declared position.
- TreeSupport::detect_overhangs uses Hanif's clamped build_plate_tilt_slope()
for the non-belt path and the belt shear for the belt path.
Both change emitted G-code, which is why they were kept out of the extraction
commit. Both are wrong only where the machine mapping is non-identity, which is
the definition of each bug.
1. Suppress lifts commanded through an unknown position.
_travel_to_z() emits full XYZ whenever the mapping must emit every axis, because
the mapping can make machine Z depend on logical X/Y, and it builds that point
from m_pos. At print start, and after any custom G-code that invalidates
position, m_pos.xy is the uninitialised origin; mapping (0, 0, z) through a
non-identity remap produces a real but wrong machine point -- for a reverse
mapping, build_vol_max, i.e. the far corner of the bed. The subsequent full-XYZ
move corrects the position, but the lift has already commanded a rapid across
the whole bed at travel speed.
Belt kinematics already guarded this; the Cartesian path did not. The guard is
now applied at all three lift sites through must_skip_lift_now(), not just the
one the extraction covered: travel_to_xyz()'s pending-lift branch,
lazy_lift(spiral_vase=true), and eager_lift(). The latter two also needed the
state fix -- both recorded m_lifted = target_lift regardless, so suppressing
only the emission would leave a later unlift() descending from a height that was
never commanded.
2. Never emit a G2/G3 arc a mapping cannot represent.
extrude_arc_to_xy() emitted G2/G3 with logical X/Y and I/J and never consulted
the mapping. There is no general fix by transforming the arc: a permutation
moves it out of the XY plane that I/J describes, a negation reverses handedness,
and the belt shear maps a circle to an ellipse that G2/G3 cannot express at all.
So supports_arc_moves() gates generation through the existing
GCode::should_disable_arc_fitting() hook, and BeltGCode's special-case override
is deleted -- belt now gets the same behaviour from the general rule instead of
its own exception.
supports_arc_moves() is m_remap_x == 0 && m_remap_y == 1, not !has_axis_remap():
an arc emits only X/Y/I/J, so a mapping that merely negates or reverses Z leaves
every emitted word untouched and keeps its arcs.
The fallback for an unrepresentable arc tessellates it into linear segments at a
0.005mm chord tolerance rather than substituting a single chord, and splits dE
proportionally across the segments. The capability check is hoisted above every
extrusion mutation: an earlier form ran it after filament()->extrude(dE) and so
extruded 2*dE on the fallback path.
Known limits of that fallback, since it is worth stating rather than discovering:
emitted relative E is conserved only to per-segment rounding (a radius-5
semicircle with dE=1.5 emits 1.50012 across 36 segments); the 0.005mm bound is a
logical-frame bound, about 0.00855mm in machine space under a 45-degree belt
shear; unequal endpoint radii and non-finite inputs are unchecked. Ordinary
export takes the original polyline when the mapping rejects arcs, so this path
is a fallback rather than the normal route.
Known gap, not claimed fixed: classic wipe towers have their own
enable_arc_fitting and their own G2/G3 emitter in GCode/WipeTower.cpp, which
should_disable_arc_fitting() does not govern. Belt printers are barred from
classic wipe towers; a remapped Cartesian printer is not.
Tests in tests/fff_print/test_gcodewriter.cpp: reverse-X remap with unknown and
with known position plus an identity control; eager_lift emitting nothing and
recording nothing; the arc-capability matrix including the Z-only cases; and the
tessellated fallback. E accounting is asserted through used_filament() rather
than E(), which resets per line in relative-E mode.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_011jgzj1sf53KMLPweZ8yeUQ
BeltGCodeWriter subclassed GCodeWriter and overrode seven methods, five of them
by copying the base body and changing the transform. The base writer already
carried an axis remap and already branched at each of its seven
coordinate-emission decisions; the subclass did the same branching with a
different transform, and the two copies had begun to drift.
Replace the inheritance with a strategy object owned by GCodeWriter:
CartesianKinematics to_machine = the existing apply_axis_remap; today's base
behaviour, moved rather than changed.
BeltKinematics to_machine = MachineFrameTransform o axis_remap o
BeltBackTransform, plus a world_coordinates variant for
the PA calibration generators.
New: src/libslic3r/GCode/MachineKinematics.{hpp,cpp}, GCode/BeltKinematics.{hpp,cpp}
Deleted: src/libslic3r/BeltGCodeWriter.{hpp,cpp} (341 lines)
Points worth a reviewer's attention:
* The predicate is must_emit_all_axes(), not couples_axes(). The base returns
true for any non-identity remap, including pure permutations that do not
physically couple axes, so the question is "must every axis word be
emitted", not a statement about kinematics.
* Every per-site word-omission branch is preserved. The base deliberately
emits X/Y only, or Z only, or drops Z when its quantised value is unchanged.
The strategy changes which transform applies, never whether words are
omitted.
* set_kinematics() replays the configured remap and build volume onto a newly
installed strategy, because BeltGCode::init_belt_writer runs before
GCode.cpp calls set_axis_remap/set_build_volume_max.
* uses_pointwise_travel_speed() preserves a pre-existing divergence rather
than introducing one: the base travel_to_xyz emits the raw configured travel
speed in its final branch, ignoring the first-layer value computed at the
top, whereas the belt path used the first-layer-aware value throughout. Both
are kept. Unifying them changes feedrates and belongs in its own change.
* The [BELT-DEBUG] block is deleted; it rate-limited itself with a
function-local static thread_local in the hot emission path, and this is the
commit that would otherwise have moved it into shared code.
This commit is intended to preserve existing export output. That is reviewed by
construction -- each emission site keeps its own omission branch and each policy
divergence is preserved -- and is NOT verified against a G-code diff corpus.
Building that corpus is the outstanding work here.
Two API-equivalence exceptions, neither reachable by any caller today:
* Belt kinematics with no plane pointer installed, m_is_first_layer true,
initial and normal travel speeds differing, travel_to_xyz() reaching its
final branch: the old belt writer selected the initial-layer speed, the new
writer selects the normal travel speed. The pending-lift and XY-only
branches keep their previous selection.
* Belt kinematics installed without set_force_normal_lift(true) and a
non-normal lift requested: the old belt writer forced a normal lift, the new
writer can take the slope branch.
The PA-pattern generator reaches the writer through explicit travel_to_z() /
travel_to_xy(), not travel_to_xyz() or the lazy/eager lift paths, and normal
belt export installs both the plane and the forced-normal-lift policy, so
neither exception changes output produced today. They are recorded because a
future caller could reach them.
tests/fff_print/test_gcodewriter.cpp was also not compiling before this branch:
it called writer.to_machine_coords(), a method that existed only on
BeltGCodeWriter. It never surfaced because the build targets OrcaSlicer, not
all, and BUILD_TESTS defaults to OFF, so that translation unit was outside every
compile path. Fixed here; the existing 30-degree coordinate assertions are kept
verbatim as the best available regression net.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_011jgzj1sf53KMLPweZ8yeUQ
Five sites carried a hardcoded fallback for imex_tools_per_gantry that had
to match the value registered in print_config_def, with nothing enforcing
the agreement, and several explanatory comments miscounted the sites they
described or cited stale line numbers.
Add imex_cfg_int/_float/_bool/_enum<T> to IMEXHelpers, which return the
value registered for the key when it is absent from the config, so the
registration is the single source and there is nothing left to keep in
sync. Route every read of the IMEX geometry keys through them: 32 call
sites across IMEXZones, PartPlate, GCodeViewer and Tab. The only direct
lookup left is the bail in PartPlate::imex_multicolor_block_reason, which
must not default because it reports a routing conflict and a defaulted
grid would produce a false warning.
imex_cfg_enum uses dynamic_cast on both halves rather than the type()
comparison the others use: every ConfigOptionEnum<T> reports coEnum, so a
type() check cannot tell one enum type from another and would cast a
ConfigOptionEnum<OtherEnum> to the requested T. The ConfigOptionPercent :
ConfigOptionFloat inheritance that rules dynamic_cast out for the float
accessor has no analogue for enums.
Correct the comments that prompted this: the cache-key input list in
PartPlate named five inputs for a nine-part key, the ImexMarkerKey note
in GCodeViewer called imex_tool_layout an input only the preview reads
when the plate keys it too, and four file:line citations pointed at the
wrong lines. Values are unchanged at every converted site; cache key
strings keep their existing representation.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Closes review comment 6.
The per-tool pressure advance work changed set_pressure_advance() for users who
are not using the feature. RepRapFirmware lost its D qualifier when no tool index
was supplied: upstream emits M572 D0 S<pa> unconditionally, and a bare M572
applies to whatever tool is currently selected and errors when there is none, so
PA started depending on tool-selection state for every RRF user. The D is back,
defaulting to 0, and D<tool> is reached only from the IMEX paths.
The same rewrite had also changed the comment separator from "<value>; Override"
to "<value> ; Override" on the Klipper, RRF, Marlin 2.x and Marlin Legacy
branches, so every non-IMEX print of those flavors carried a one-byte diff.
Restored. Upstream is internally inconsistent here -- BBL and Repetier do use the
spaced form -- and the point is to match it exactly rather than to tidy it.
Emitted output for all six flavors with no tool index is now byte-identical to
upstream. Verified on a real slice: a Klipper profile emits
"SET_PRESSURE_ADVANCE ADVANCE=0.02; Override pressure advance value", an exact
string match, with no EXTRUDER= qualifier. The tests were pinning the regressed
form and are inverted.
Also records at the imex key registrations why they are kept out of the g-code
config block, matching the house convention at the other banned keys.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
M104/M109 address a heater, but every caller of the instance
GCodeWriter::set_temperature overload addresses filaments by logical id, so on a
printer whose physical_extruder_map is not the identity the emitted T named the
wrong head -- or, where the logical id exceeds the head count, no head at all.
With a map of 0,0,0,0,1,2,3 a toolchange to filament 5 emitted "M109 S265 T4"
and "M104 S190 T4 ;cooldown" while the head it meant was T1.
Upstream already treats these commands as physical: the preheat it injects in
GCodeProcessor maps through the same map before emitting, and BBS's own wipe
tower does likewise. Emitting logical is the half that never got the memo.
That mismatch also disabled the cooldown suppression beside the preheat, which
compares the line's T against pem[tool_number] and so never matched a logical
one -- 171 cooldowns survived in a two-head print where none should have. Worse,
it could match the wrong line: a cooldown for filament 1 emitted T1, and a
toolchange to filament 5 gives pem[4] == 1, so a legitimate cooldown for head 0
was deleted because the incoming head happened to be numbered 1.
Translate once, in the instance overload every logical-space caller passes
through. The static overload is already physical-in and is left alone.
Gated on is_imex. physical_extruder_map carries two readings in this tree: the
BBS paths index it by extruder id, the IMEX paths by filament id, and the two
coincide only when the filament and nozzle counts match. Mapping unconditionally
would impose the IMEX reading on profiles that mean the other one --
fdm_bbl_3dp_002_common ships a non-identity [1,0], spared today only because
single_extruder_multi_material suppresses the T qualifier entirely.
The wipe tower's interface-temperature pass has to move with it. It strips the
M109 that post_toolchange emits by searching for that filament's tool index, so
it now searches for the mapped one; left alone it would have stopped matching,
and the surviving blocking M109 would have silently defeated the interface
temperature. Its sibling pass reads WipeTower2 output, which emits no T at all,
and is deliberately unchanged.
The bare T<n> toolchange stays logical -- it selects an AFC lane, not a heater.
Test slices two objects across a head boundary, the only case that reaches this
emission: the same-physical short-circuit in set_extruder suppresses the
cooldown entirely for lane swaps within one head. It scans every M104/M109
rather than matching fixed strings, so it catches any unmapped emission and not
just the two sites changed here. With the mapping neutered it reports 101
offending lines; with it in place, none.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
- BeltGCodeWriter::travel_to_xyz final branch used config.travel_speed
instead of the computed first-layer-aware travel_speed.
- extrude_to_xyz decided emit_xyz vs emit_xy from pre-remap Z; emit full
XYZ whenever an axis remap is active so remapped machine-Z is never
dropped.
- base travel_to_xyz now applies apply_axis_remap() on all emitted
destinations (standalone remap on non-belt printers was unremapped).
- spiral/arc travels fall back to normal linear lift under active remap
(endpoint-only remap can't preserve arc plane/I-J).
- set_axis_remap() is now synced unconditionally each export to avoid a
reused writer retaining a stale non-identity mapping.
The linear approximation used a heuristic segment count clamped to 4..16, so the
lift ran as a coarse polygon. Every vertex is a direction change large enough to
hit the firmware's jerk limit, forcing a decelerate/accelerate at each corner —
the lift micro-stutters instead of running at speed. The segment count now comes
from the chord deviation against the slicing resolution, reusing
Geometry::ArcWelder::arc_discretization_steps, which keeps the turn at each
vertex shallow enough for the firmware to carry speed through the whole move.
Points are emitted through GCodeG1Formatter so they carry the same quantization
as the rest of the G-code, and the move comment now trails the feedrate line to
match _travel_to_z and the G2/G3 branch. No change when arc fitting is enabled.
Brings the belt-printer work up to date with 591 upstream commits.
Conflict resolutions (12 files, 42 hunks):
- GCode.cpp: adopted upstream's per-filament/per-nozzle config refactor
(get_filament_config_index, NOZZLE_CONFIG), the extracted
generate_timelapse_gcode + farthest-point timelapse, and the
ConfigOptionFloatsNullable calibration options. Re-applied the belt
hooks on top: init_belt_writer / axis remap / FirstLayerPlane setup,
on_set_origin, the belt-corrected calib_z for the volumetric speed
tower, and path_on_first_layer (belt's per-path first-layer test) in
place of upstream's layer-index on_first_layer() in the acceleration,
jerk and overhang-detection paths. Swept upstream's new m_writer.
uses to m_writer-> since belt holds the writer by unique_ptr.
- interpolate_value_across_layers: kept upstream's banded stepping and
belt's object-Z-span ratio; dropped upstream's duplicate ratio decl.
- Plater.cpp: took upstream's guarded add_model(...) early-returns and
the VFA vfa_layer_height plumbing; kept the belt temp-tower path,
_calib_apply_belt_mode and belt_calib_flip_ringing_tower. Dropped the
VFA "cut upper" block, superseded upstream by model scaling.
- Brim.cpp: upstream's ObjectInstanceID-keyed brimAreaMap, keeping the
belt early-return.
- 3DScene.cpp: kept both the belt build-plate tilt up_direction and
upstream's per-extruder printable-height shading.
- GCodeViewer.cpp: kept upstream's dim-previous-layers setup and belt's
exemption from the same-result early return.
- TreeSupport.cpp: upstream's >= 0 roof-layer fix inside belt's
belt-floor branch.
- calib.cpp / GCode.hpp / GCodeWriter.{cpp,hpp} / Print.hpp: upstream's
additions adapted to belt's pointer-held writer and helpers.
- Custom.json: kept profile version 02.04.00.03 (belt) over upstream's
02.04.00.01; both bumped from 02.04.00.00.
Building this tree needs the wxInspector dependency, which upstream
added in the interim (python3 and wxWidgets 3.3.2 were already present
in the shared deps prefix).
* Ensure spiral lift positive quadrant
* check for printable area
* clamp area
* simpler version
* Adjust printable area bounds with safety safety margin
Added safety margin to printable area bounds calculations.
* increase safety margin
* Refactor safety margin calculations in GCodeWriter
* New Logic
Co-Authored-By: Ian Bassi <12130714+ianalexis@users.noreply.github.com>
---------
Co-authored-by: Ian Bassi <12130714+ianalexis@users.noreply.github.com>
Conflicts were all co-located additions rather than design collisions:
- GCode.cpp: adopt upstream's toolchange(filament_id, nozzle_id) signature and
per-variant set_config_index() while keeping the IMEX bare-T<n> suppression;
rebase the second-layer temperature loop's non-IMEX branch onto upstream's
get_filament_config_index() resolution.
- Preset.cpp / PresetBundle.cpp / PrintConfig.cpp: keep both sides' option-list
and enum-map entries.
- GLCanvas3D.cpp: upstream's printable_heights argument plus the IMEX ghost pass.
- PartPlate.cpp: keep <set> (still used).
- test_gcodewriter.cpp / test_3mf.cpp: keep both sides' test cases.
Resolves two conflicts:
- GLCanvas3D.hpp: keep both the IMEX ghost render declarations and
upstream's _render_wireframe_overlay().
- test_gcodewriter.cpp: both sides appended test cases to the same
region; keep upstream's origin/machine-limit tests alongside the
pressure-advance and temperature scenarios.
A dual-nozzle H2C print with support filament hangs at its first nozzle
switch. The emitted file shows the change-filament block's M620 O ordinal
jumping from O1 straight to O230, plus a duplicate "M1020 S<n>" toolchange
command right after every change block. Two causes, fixed together because
they interlock (the ordinal check keys off the same toolchange detection
that suppresses the duplicate):
- append_tcr incremented m_toolchange_count once per prime-tower visit
(roughly once per layer), while the change-filament template only emits
its M620 O{toolchange_count + 1} line on real filament changes. With 229
change-less sparse tower layers below the first support layer, the first
real change reported ordinal 230. The counter now advances only when the
expanded change block really contains a toolchange command, and the
placeholder exposes the upcoming change's ordinal (count + 1). The
set_extruder path already counted per real change and is unchanged.
- toolchange_prefix() returned "M1020 S" for BBL printers, so the
custom_gcode_changes_tool() dedup could never match the stock profiles'
line-leading "T[next_filament_id] ..." commands and the writer's own
toolchange was appended after every change block on dual-extruder
machines. The prefix is now the plain "T" (the manual-filament-change tag
branch stays first), and the M1020 form moved into GCodeWriter::toolchange()
as an explicit branch that also carries the nozzle:
"M1020 S<filament> H<nozzle>". The nozzle parameter is signed on purpose:
the null-safe nozzle lookup legitimately yields -1, matching the stock
templates' own H-1 convention.
The prefix change also lets the CoolingBuffer recognize the change blocks'
T commands as tool boundaries on BBL printers (its per-filament attribution
previously keyed off the duplicate M1020, or nothing at all on
single-extruder models); its existing out-of-range guard ignores
T1000-class machine commands.
Verification: full suites green (libslic3r 48998 assertions / 169 cases;
fff_print 692 / 65 including three new scenarios - writer emission per
printer kind, dedup + ordinal progression on sequential prints, and a
prime-tower regression scenario verified to fail against the old per-visit
counting). Byte gate: 18 of 20 fixtures bit-identical; the sequential repro
differs by exactly its 3 removed duplicate M1020 lines, deterministic
across two runs. Reslicing the field project that exposed the hang yields
M620 O1 followed by a gapless O2..O59 and zero duplicate M1020 lines.
Co-authored-by: songwei.li <songwei.li@bambulab.com>
Catches the iXex/IDEX branch up to upstream main (44 commits). One
content conflict resolved:
- src/libslic3r/Print.hpp: kept upstream's default-initialized
m_origin {0,0,0} alongside our m_imex_slice_offset member.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Catches the iXex/IDEX parallel-printing branch up to upstream main
(102 commits). Two content conflicts resolved:
- src/libslic3r/Preset.cpp: s_Preset_printer_options — kept upstream's
new "use_3mf" key and our iMEX printer-capability/mode keys.
- tests/fff_print/test_gcodewriter.cpp: upstream revived the disabled
suite (#14196), dropping the obsolete [.]-tagged lift() test and its
config_lift_unlift.ini; kept their set_speed + z_hop tests and appended
our 10 per-firmware set_pressure_advance/set_temperature scenarios.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
124 upstream commits including CrealityPrint integration (added include
in Plater.cpp alongside the existing IMEXHelpers include), profile fixes
and version bumps (#14084, #14085, Polymaker), CI artifact publishing,
test refactors (arachne walls test added; test_3mf/test_config/
test_gcodewriter content moved/removed upstream — IMEX test file
preserved as it is feedback-only), translations.
* Fix air filtration gcode emitted even if not not supported
- do not emit air filtration gcode if not supported by the printer
- removed redundant "add_eol" parameter from "set_exhaust_fan()" function
Includes nozzle-diameter guards for printers without nozzle info (#13255,
now landed upstream) and manual-calibration nozzle mismatch fix (#13882).
# Conflicts:
# src/slic3r/GUI/GCodeViewer.cpp
# src/slic3r/GUI/GLCanvas3D.hpp
# src/slic3r/GUI/Tab.cpp
Reconciles the belt-printer branch with upstream PRs through #13723. Six
files had conflicts; three additional files needed manual follow-up fixes
where the auto-merge produced code that referenced upstream-renamed fields
or changed function signatures.
Notable reconciliations:
- TreeSupport.cpp: kept belt-floor early-exit branches around HEAD's
drop-down logic, folded upstream's `(distance_to_top > 0 ? 1 : 0)`
formula into the non-belt-floor path (upstream PR #11812). Dropped dead
`roof_enabled`/`force_tip_to_roof` locals.
- TreeSupport3D.cpp: combined upstream's safety-offset + remove_small
changes with HEAD's belt-floor clip in the per-slice trim loop. Dropped
HEAD's `else` block (superseded by upstream's rewritten bottom-contact
propagation) and re-added the belt-floor clip into the new propagation
loop. Gated the propagation on belt printers to prevent OOM when
belt-floor clipping produces empty initial slices.
- TriangleSelector.{cpp,hpp}: merged both new `select_patch` parameters
(HEAD's `up_direction` and upstream's `select_partially`); body uses
`dot(up_direction)` for the overhang angle check and forwards
`select_partially` to `select_triangle`.
- SupportMaterial.cpp: `slicing_params.soluble_interface` →
`zero_gap_interface_bottom` in HEAD's `detect_belt_floor_bottom_contacts`,
matching upstream's same-purpose rename at line 2495.
- Custom.json, GCodeWriter.cpp: simple additive merges (kept entries /
includes from both sides).
Verified by building OrcaSlicer (RelWithDebInfo) after a full deps
rebuild (Eigen v5.0.1, libigl v2.6.0 are now managed deps) and slicing
a scaled Benchy on the NORMALIZER belt-printer profile without OOM.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
