Code review items (raistlin7447):
1. PrintObject::slice() zeroes m_belt_min_z, m_belt_global_z_offset and
m_belt_global_xy_correction before slicing. They were only written in belt
mode, so a project switched to a normal printer, or whose tilt axis was set
to None, kept the old offsets and shifted the adaptive infill octree and the
organic support layers by them.
2. TreeModelVolumes shifts the support blockers into the raft-offset index
space; a test now pins the index the blocker lands on.
3. The final-alignment clamp in libnest2d is opt-in (NfpPConfig::clamp_to_bin)
and arrange sets it for belt printers only. Printers with an off-centre
best_object_pos keep their alignment; a flat-bed test pins that.
4. The preview's belt view follows the loaded G-code, not the selected printer:
GCodeProcessor carries the file's belt keys (and, for a belt file, its bed)
into export_config_for_render(), and GCodeViewer enables the belt view from
the header tilt.
5. belt_shift_layer_grid() also shifts the cached belt floor and the global Z
offset, so a support-only or brim-only change after the purge-prism snap
matches a fresh slice.
6. update_print_fff_config() resets raft_layers and draft_shield on a belt
printer instead of only greying out the fields Print::validate() rejects.
7. GCodeWriter takes a first-layer point test instead of the FirstLayerPlane;
GCode installs one that measures from the belt surface, like its
extrusions, so the first-layer travel speed and the second-layer
temperature change no longer depend on the gcode_remap_* convention.
8. belt_brim_clip_leading_edge() is exported and called by both the generator
and the test.
9. Both phong.vs shaders use slope.up_direction for the overhang highlight.
The pre-slice and G-code axis remaps are gated on belt_printer through
BeltTransformPipeline::axis_remap_enabled(), so belt keys left in a profile
cannot change a non-belt print.
Tests requested in the review: belt-only keys at non-default values leave
non-belt G-code unchanged; switching a sliced project from belt to non-belt
(and tilt axis None) matches a fresh slice; a support-only change on a belt
purge print matches a fresh slice; non-belt start G-code moves keep the
first-layer Z in the processor; the belt brim's segment count catches a band
emitted twice.
The belt-to-non-belt test exposed an unrelated gap: invalidate_step(posSlice)
re-invalidated posSupportMaterial but not posSimplifySupportPath, so after
any re-slice the regenerated support paths were exported unsimplified.
posSimplifySupportPath is now in that list.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
Brings belt-printer up to main 4b4a261787. Resolutions:
- G-code header (#15897, #15915): main moved the header, config and
thumbnail block later in _do_export; write_belt_header() moves with it,
still after the thumbnails and outside the BTT_TFT gate.
- _extrude: first-layer acceleration keeps the per-path first-layer plane
test with main's cached nozzle index (#16028); main's set_speed out-param
form (#16108) everywhere else.
- GCodeWriter (#16108): the arc-to-polyline fallback for machine mappings
that cannot express G2/G3 now runs in the out-param extrude_arc_to_xy,
which is the overload GCode calls, and appends to the caller's string.
- GCodeProcessorResult: the belt fields join main's forwarding assign.
- Clipper2 (#15969): belt arrange helpers take Slic3r::Point; the tree
support join types lose their ClipperLib qualifier.
- CLI arrange (#15837): belt printers still reserve no wipe tower.
- Wipe tower options (#15841): the two new sparse-layer toggles are hidden
for belt printers like the rest of the tower options.
- Keyboard shortcuts (#15706): main's registry replaces the old key switch;
the belt view toggle is re-registered in the next commit.
- Print::process: the belt purge-plan undo runs before main's SliceStarted
event.
- scripts/filament_id_snapshot.json: deleted on main (a77209af8f).
- Includes and appended tests: union of both sides.
With best_object_pos away from the bed centre the placer packs the pile
inside the bin and then translates it so its centre lands on that point,
without checking that it still fits there. A belt printer aims at the
leading end of the belt (BabyBelt Pro: 0.5, 0.05), so any pile longer than
the 50 mm around that point was pushed past the edge: four 90 mm parts on
the 95 x 500 mm belt ended with one across the edge and one outside while
290 mm of belt stayed free.
The final alignment now stops the pile at the edge of the bin; the items'
inflated boxes leave the object spacing as the margin. A pile that does not
fit along an axis is centred on it, as before.
* fix(libnest2d): skip the excluded-region alignment pass when there are none
NfpPlacer::finalAlign(), run from clearItems() and the destructor, always
ran the "find a best position inside the NFP of fixed items" pass even when
no items are fixed. With nothing to avoid, calcnfp() computes the inner-fit
NFP of the pile and can feed clipper a coordinate outside its allowed range.
On Linux/clang the value stays in range so it went unnoticed; on MSVC the
clipper "Coordinate outside allowed range" exception escapes the noexcept
destructor and aborts the process (exit 0xC0000409).
Build the excluded set up front and only run the pass when it is non-empty.
The block exists solely to keep the pile clear of fixed items (excluded
regions / wipe tower), so it is a no-op when there are none and the
wipe-tower behaviour is unchanged.
* test(libnest2d): remove dead nesting tests and split the suite by feature
Seven of the suite's hidden [.] test cases drove code paths Orca abandoned
at the BambuStudio fork: BottomLeftPlacer (used nowhere in src/) and the
stock default NfpPlacer backend, which returns zero bins in Orca. They have
been red since the fork and are never registered with ctest. Remove them.
Split the 1,000-line libnest2d_tests_main.cpp into per-feature files, per the
repo convention, sharing a header for the no-fit-polygon backend setup that
every translation unit must agree on (ODR):
libnest2d_tests.cpp Item and nest() basics
test_geometry.cpp geometry primitives
test_nfp.cpp no-fit-polygon machinery
libnest2d_test_utils.hpp shared includes and the NFP backend specialisation
Along the way: drop a debug exportSVG() helper that only wrote a file on test
failure (so the suite never leaves stray assets), convert the deprecated
Catch::Approx to WithinRel/WithinAbs matchers, and give the tests descriptive
names.
* test(libnest2d): add NfpPlacer unit tests
NfpPlacer is the placement engine the arranger drives, but the suite only
covered the geometry primitives. Add a fixture and five tests that exercise
pack()/accept() directly: a single item lands in the bin, an oversized item
is rejected, the first item is seeded for every starting point, many items
pack without overlap, and the rotation candidates are searched. This lifts
nfpplacer.hpp line coverage from 42% to 87% in the libnest2d suite.
* test(libslic3r): add arrangement::arrange() integration coverage
The libnest2d suite cannot reach Orca's real nesting entry point because it
does not link libslic3r. Add test_arrange.cpp driving arrangement::arrange():
items land on the bed and within bounds, do not overlap, are spaced by their
inflation, an oversized item stays unplaced, overflow spills onto virtual beds,
an empty input is a no-op, and the DONT_ALIGN and USER_DEFINED final-alignment
paths are exercised. A self-test guards the overlap check the other cases use.
* src/*/CMakeLists.txt: adds SYSTEM to arget_include_directories()
* src/*/CMakeLists.txt: removes duplicate sources from lisbslic3r_sources and SLIC3R_GUI_SOURCES"
* .gititnore: adds CMakeLists.txt.user and CMakeLists.txt.autosave
* deps_src/*/CMakeLists.txt: adds SYSTEM to arget_include_directories()
* removes #pragma once from .cpp file
Move many third-party components' source codes from the src folder to a new folder called deps_src. The goal is to make the code structure clearer and easier to navigate.
