* Toolchange Cyclic Order
* Apply cyclic order to first layer
* Unit test
* Copilot fixes
---------
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
* fix(GUI): honor "Ignore" when layer height exceeds the configured maximum
Entering a layer height above the printer's max_layer_height on the Print
Settings tab fired two guards in sequence. Tab::on_value_change prompts
"...Adjust to the set range automatically?" with an Adjust/Ignore choice, and
ConfigManipulation::update_print_fff_config then showed an OK-only "Too large
layer height. Reset to X" dialog whose result was never checked, so it always
reset the value. The second guard overrode the user's "Ignore", resetting the
layer height regardless.
Changes:
- Extract the shared Adjust/Ignore dialog into
ConfigManipulation::layer_height_out_of_range_dialog, reused by the tab
(Tab::on_value_change) and the per-object/part settings panels. The dialog now
names the value it will clamp to and reads correctly for too-low as well as
too-high.
- The tab/plate path is already covered by Tab::on_value_change, so the
duplicate reset is dropped from update_print_fff_config.
- The per-object/part panels have no on_value_change hook, so add
ConfigManipulation::check_object_layer_height and call it from the object
settings update paths, gated on the edited option (changed_opt_key ==
"layer_height"). It prompts once per layer-height edit and does not re-prompt
when unrelated object settings change after the user chose "Ignore".
Fixes#14214
* refactor(GUI): unify the layer-height range check across tab and object panels
Copilot review of #14369 noted that the per-object check only guarded the
max at extruder 0 and skipped the too-low case, diverging from the tab.
Move the whole range check into ConfigManipulation::check_layer_height,
used by both Tab::on_value_change and the per-object/part panels. It takes
the widest [min, max] window across the printer's extruders, offers
Adjust/Ignore in both directions, and resets a near-zero value. The tab's
inline block collapses to one call, dropping the duplicated limit logic.
* fix(GUI): only enforce layer-height limits that are actually set
max_layer_height defaults to 0 (unset), so the unconditional range check
offered to clamp any layer height to 0 on presets that don't define it.
Guard each branch (near-zero, too-high, too-low) so an unset limit disables
that direction; the slice-time nozzle-diameter check still applies.
Also run check_layer_height before update_print_fff_config in the object
panels so a near-zero per-object value prompts the same way the tab does,
with update_print_fff_config's fallback still covering the no-minimum case.
* Disable prime tower width for rib walls
Only enable the prime tower Width field when the selected wall type uses the standard tower shape. Rib towers use the rib-specific settings instead, so leaving Width editable suggests it changes rib geometry when it does not.
Fixes#14537
Co-authored-by: Copilot <223556219+Copilot@users.noreply.github.com>
* Simplify prime tower width toggle
Use the existing rib-wall helper when disabling the prime tower width control for rib wall towers.
Co-authored-by: Copilot <223556219+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <223556219+Copilot@users.noreply.github.com>
* Fix junction deviation and jerk settings behavior
Process settings now follow the selected printer's junction deviation
configuration. When machine_max_junction_deviation is enabled,
default_junction_deviation is shown and jerk settings are hidden. When
junction deviation is disabled, jerk settings are restored and
default_junction_deviation is hidden.
Fix a validation issue where junction deviation mismatch warnings could
be reported even when machine_max_junction_deviation was set to 0.
Warnings now apply only when junction deviation is active and point
directly to default_junction_deviation.
Also simplify Motion ability page visibility checks by reusing local
firmware-flavor booleans.
* GUI tweak
- separate Junction Deviation segment
- JD and Jerk stay visible
* Add Optimized Gyroid infill (auto-tuned wavelength + amplitude)
New infill geometry derived from FillGyroid. Two parameters are
auto-computed per-region from density, line spacing, and layer height
(no user inputs):
omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing)
clamped to [0.5, 2.0]
-- Euler-Bernoulli buckling: critical load ~ 1/L^2,
so shorter wavelength under higher load (denser infill)
raises buckling resistance.
amplitude = 0.55 / omega^2, clamped to [0.20, 0.65]
-- Curved-beam bending stress: peak stress ~ A * omega^2,
so amplitude is reduced as omega rises to keep peak
fiber stress bounded while preserving stiffness.
Files:
- src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new)
- src/libslic3r/Fill/FillBase.cpp (factory case)
- src/libslic3r/Fill/Fill.cpp (switch case)
- src/libslic3r/Layer.cpp (switch case)
- src/libslic3r/PrintConfig.{hpp,cpp} (enum + label)
- src/libslic3r/CMakeLists.txt (build sources)
User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown.
Density still chosen by user; omega/amplitude are internal.
* Fix build: layer_height is in FillParams, not Fill base
* Add ipOptimizedGyroid to multiline infill list in ConfigManipulation
* Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean
Per @RF47's review feedback, fold the optimized wave math into FillGyroid
itself behind a per-region boolean instead of a separate infill enum.
What changes:
- New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default
false). When unchecked, gyroid behavior is byte-identical to before.
- Optimized wave math (compute_omega_factor, compute_amplitude_factor,
f_opt, make_*_opt, make_optimized_gyroid_waves) lives inside
FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized.
- FillParams gains a bool gyroid_optimized field, populated in Fill.cpp
from region_config alongside fill_multiline.
- UI checkbox added under Strength > Infill in Tab.cpp, label
"Optimize gyroid wave (experimental)". Toggle is hidden by
ConfigManipulation when sparse_infill_pattern != ipGyroid.
- "gyroid_optimized" added to s_Preset_print_options for preset I/O.
What goes away:
- ipOptimizedGyroid enum value, factory case, switch cases, dropdown
label, string key.
- FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into
FillGyroid.cpp).
- Net diff drops by ~250 lines.
Existing profiles using gyroid are unaffected.
* Wire gyroid_optimized through SurfaceFillParams to FillParams
Linux build failed because line 921 in Fill.cpp populates a
SurfaceFillParams (the dedup struct), not FillParams directly.
Add the field there, in operator< / operator==, and copy it to
FillParams at both conversion sites.
* Use toggle_line for gyroid_optimized: hide row when pattern != gyroid
* Account for multiline wall thickness in omega correction (per @RF47)
When fill_multiline = N, each gyroid wall is N lines thick, so the
geometric scale fed into the buckling correction term should be
spacing * N rather than spacing. Increases omega (tighter wavelength)
when multiline is enabled, consistent with the thicker wall being
more buckling-resistant.
* Optimized gyroid via marching squares on the implicit scalar field
Per @RF47 review: replace the analytical f_opt / make_one_period_opt
wave generator (which had visible kinks at vertical-horizontal
transitions) with a marching-squares iso-extraction on the gyroid
scalar field, modeled on FillTpmsFK.cpp.
- New marchsq::GyroidField in FillGyroid.cpp evaluates
F(x,y,z) = sin(fx*x)cos(fy*y) + sin(fy*y)cos(fz*z) + sin(fz*z)cos(fx*x)
where fx = omega * baseline (anisotropic in x), fy = fz = baseline.
- get_gyroid_polylines() runs marching squares at iso=0 and converts
rings to polylines.
- _fill_surface_single() optimized branch now builds GyroidField,
runs marching squares, and skips the bb.min translate (field
output is already in absolute coords).
- Dropped: f_opt, make_one_period_opt, make_wave_opt,
make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude
has no clean analog in iso-zero extraction.
- Standard (non-optimized) gyroid path unchanged.
* Mass calibration: compensate period by cbrt(omega) for x-anisotropic field
Per @RF47: optimized vs standard gyroid had different masses at the
same sparse_infill_density setting. Cause: scaling fx by omega while
leaving fy=fz at the baseline raised the surface-area-to-volume ratio
by approximately omega^(1/3) (the geometric mean of the three
frequencies).
Fix: multiply the base period by cbrt(omega) so the geometric mean of
(fx, fy, fz) returns to the standard baseline. Net effect:
fx = omega^(2/3) * baseline_orig
fy = fz = omega^(-1/3) * baseline_orig
which preserves total mass at the same density setting while
preserving the load-direction anisotropy this PR introduces.
* Switch optimized gyroid anisotropy from X to Z (per @RF47)
Z is the typical compression-load axis for FFF parts and is not at
delamination risk under compression — so the dominant failure mode
is column buckling of the vertical strands themselves. Tightening
fz directly shortens the effective vertical strand length, which
improves Z-axis buckling resistance.
Mass calibration via cbrt(omega) period compensation still applies
(scaling exactly one of three frequencies by omega; the geometric-
mean preservation argument is symmetric across axes).
* Update src/slic3r/GUI/Tab.cpp
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
* Address review feedback (Copilot + @RF47)
- Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid)
so non-gyroid surfaces don't differ in SurfaceFillParams by an
irrelevant flag (would unnecessarily split fill batching).
[Copilot suggestion, RF47 confirmed correct]
- PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength
is parameterized (the marching-squares iso=0 extraction is invariant
to a uniform field scale, so amplitude has no effect).
- FillBase.hpp: shorten gyroid_optimized comment to match the actual
carried state (no amplitude term).
- FillGyroid.cpp: shorten the marchsq namespace comment block; the
ODR concern was overstated (FillTpmsFK uses the same pattern fine).
* Drop redundant marchsq bb expansion (Copilot)
bb is already offset by 10 * scale_(spacing) above for edge-artifact
margin; the second offset on bb_field doubled the raster area for no
geometric benefit and hurt CPU time on large parts.
* Update src/slic3r/GUI/Tab.cpp
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
* Fix density mismatch + rename to Z-buckling bias optimization
Issue (per @ianalexis): at the same sparse_infill_density setting,
the optimized branch produced denser fill than standard. Verified via
Python sim (sim_gyroid_compare.py) using marching squares on the
implicit field across multiple z slices.
Root cause: the omega formula was inverted from the buckling-physics
intent. The naive sqrt(density_adj) factor produced omega < 1 at
typical print densities (10-30%), which LENGTHENED the Z wavelength
instead of shortening it -- net loss in both mass and strength.
Fix:
- compute_omega_factor: invert to sqrt(1 / density_adj), clamp to
[1.0, 2.0]. Now omega = 2.0 at low density (long strands need
most help) and clamps to 1.0 above ~30% density (no-op, since
standard gyroid is already short enough).
- Remove the cbrt(omega) period compensation. Empirically (sim
table embedded in FillGyroid.cpp comment) the inverted formula
keeps line length per area at ~1.000 of standard across all
densities with no period scaling needed.
Predicted gains (sim, Z-axis Euler buckling proxy):
density line/std strength/std
10% 1.000 2.84x
15% 1.000 1.89x
20% 1.000 1.42x
30%+ 1.000 1.00x (no-op)
Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op
above 30% density and Z-only). Renamed user-facing label to
"Z-buckling bias optimization (experimental)" with updated tooltip
that scopes to vertical compression and discloses the density cutoff.
Internal config key (gyroid_optimized) unchanged for diff size.
Real-world Instron compression tests at Brown's Prince Lab to follow.
---------
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
Hide tree support parameters not in use
- hide independent support layer height for organic tree support
- hide threshold overlap for tree supports
Co-authored-by: SoftFever <softfeverever@gmail.com>
Fix hybrid tree first-layer support base flow and UI consistency
Fix incorrect first-layer generation for hybrid tree supports.
The support base on the first layer used brim flow instead of support material flow,
which could lead to incorrect extrusion behavior and wrong material usage in
multi-material prints.
Additionally, spacing and density for the regular support part were not consistently
derived from the actual first-layer support flow when first-layer and regular
line widths differed.
Hybrid-specific behavior is clarified:
- first-layer expansion applies only to the regular support part
- tree-only regions keep their existing behavior
The first-layer support pattern is aligned with normal and organic tree supports
to ensure consistent and meaningful density behavior.
Also make first-layer support expansion and density settings visible whenever
supports are enabled, as density was already affecting hybrid supports but was
hidden in the UI.
* Elefant foot compensation for solid layers
Elefant foot compensation for solid layers above bottommost by infill density manipulation.
* Update Fill.cpp
* change the option to expert cat
* use is_approx for float
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Union ex brims
Revert "Union ex brims"
This reverts commit bbc9a39faf318dc2df093eb2bdcebf19a4162fe9.
Update Brim.cpp
* dont repeat paths
* Update Brim.cpp
* multimaterial brim independiente
* Normal brim if is by object
* fix print order
* cleaning 1
* cleaning 2
* Normal brim if multimaterial on first layer
* fix artifact
* combine_brim optional
refactoring
* refactoring gcode.cpp
* refactoring brim.cpp
Update Brim.cpp
* Remove multimaterial first-layer check for brims
Stop detecting extruders used on the first layer and remove the is_multimaterial_first_layer guard. Simplify can_combine_brims to only consider combine_brims and whether printing is ByObject, allowing brims to be combined across extruders unless printing by object or combine_brims is disabled. Cleans up unused code and simplifies brim-generation conditions.
* Remove material specification from unified brim comment
* Update PrintConfig.cpp
Previously, wipe tower behavior was determined by checking if the printer
was a QIDI vendor. This introduces a configurable enum (Type 1 / Type 2)
so any printer can select its wipe tower implementation. BBL printers
remain hardcoded to Type 1. Qidi profiles default to Type 1.
