* Add IdeaFormer IR3 V2 belt printer profile
Self-contained vendor profile for the IdeaFormer IR3 V2 (45 deg belt printer):
machine (0.4 nozzle) + 0.20mm process + Generic PLA/PETG filaments, with the
belt machine-frame transforms set explicitly on the machine preset
(belt_printer, belt_slice_rotation x/45/global, build_plate_tilt_x=45,
gcode_remap_x/y/z, gcode_shear_z=pos_tan, gcode_scale_y=inv_cos).
The vendor bundles its own machine/process commons (fdm_belt_common,
fdm_klipper_common, fdm_machine_common, fdm_process_common) on purpose:
OrcaSlicer resolves system-preset inheritance per-vendor, so a profile that
inherits the Custom vendor's commons cross-vendor fails to resolve its parent
and the whole IdeaFormer vendor silently fails to load. Bundling the commons
(and listing them in IdeaFormer.json in dependency order) keeps the vendor
self-contained, matching how every other vendor folder is structured.
Machine limits, bed temperature (75 C for belt PLA) and start/end G-code are
taken from a working IdeaFormer IR3 V2.
* feat(belt/profile): eSUN PLA @IdeaFormer IR3 V2 — HW-calibrated belt filament
Add an eSUN PLA belt profile for the IR3 V2, inheriting Generic PLA @IdeaFormer
IR3 V2 (self-contained: parent is in the same IdeaFormer vendor, registered
after it in filament_list). HW-calibrated on the IR3 V2:
- nozzle_temperature 200/200 (temp-tower calibration)
- pressure_advance 0.12 (PA calibration)
- filament_max_volumetric_speed 10 mm³/s (max-vol-speed calibration: wall
failed at 126 mm/s → 126 × 0.0798 mm³/mm ≈ 10 mm³/s)
* Bump Elegoo profile version to refresh installed bundle
Bumps the Elegoo vendor profile version so installed profile bundles are refreshed from bundled resources after the recent Elegoo profile sync.\n\nThe previous version stayed at 02.04.00.00 after the profile layout changed, so existing installs could keep loading stale system/Elegoo files. That stale bundle can abort during profile loading and cause user presets inheriting from Elegoo machines, such as OrangeStorm Giga and Neptune 3 Max, to report missing parents.\n\nValidation:\n- jq parsed resources/profiles/Elegoo.json\n- verified all Elegoo.json sub_path entries exist\n- git diff --check
* Fix Elegoo process profile manifest
* Fix: Disable redundant toolchange retraction for Elegoo Centauri Carbon
Sets `retract_length_toolchange` to 0 in the Elegoo Centauri Carbon (ECC) machine profile.
This resolves an issue where a massive filament blob would form on the prime tower immediately after resuming a manual filament change (M600). The blob was caused by a conflict between OrcaSlicer's default toolchange logic and Elegoo's hardcoded firmware behavior:
- Elegoo's firmware (specifically the `cmd_PAUSE` and `cmd_RESUME` sequences) completely takes over pressure management during an M600. It performs its own initial 2mm retraction, a 120mm purge, and a silicone brush wipe, returning the print head to the prime tower perfectly primed.
- Previously, Slicer was unaware of the firmware's priming and would issue a redundant 2mm un-retract (`G1 E2`) upon resume. Forcing 2mm of filament out of an already-full nozzle created the blob.
By disabling the toolchange retraction (`0`), Slicer correctly hands off filament pressure management during an M600 entirely to the Elegoo firmware, preventing double-retractions and eliminating the blob.
* fix errors after merging main
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Update the stealth mode description to reflect the current code changes in 2.4.
* disable HMS if bambu network plugin is not installed or in stealth mode
* fix build err
* add hide_login_side_panel to control whether to show login panel in home page
* Support 'Default' filament option (index 0)
Treat filament index 0 as the new "Default" (use active object/part filament) instead of using 1. Update config defaults and tooltips for wall/sparse/solid infill filament options (min/default -> 0, tooltip explains "Default"). Adjust normalization and propagation logic to respect explicit feature overrides and only apply base extruder when feature values are zero; only copy sparse->solid infill when sparse > 0. Introduce FeatureFilamentOverrideMask and clamp_feature_filament_to_valid to resolve and clamp feature filaments. Update UI lists and selection behavior to expose a "Default" entry and handle zero-based indices in PartPlate and Plater.
* enable_filament_for_features option
Co-Authored-By: LixNix <105106115+lixnix@users.noreply.github.com>
* \n
* Allow wipe_tower_filament to equal nozzle count
Relax the assertion in Print::extruders to permit wipe_tower_filament == config().nozzle_diameter.size(). The configuration value is 1-based and the code subtracts 1 when pushing the extruder index, so equality should be valid and selecting the last nozzle should not trigger an assertion.
* Revert "Allow wipe_tower_filament to equal nozzle count"
This reverts commit 2c976574327a8bcdc74a1b296bf1aaff7752a94e.
* Revert "enable_filament_for_features option"
This reverts commit 01c13baeddb8e26793f752deab788ee4d086975b.
* Migrate legacy feature filament defaults
Add migration logic to convert legacy feature filament selections from 1 to 0 for older 3mf files. Introduces a local migrate_legacy_feature_filament_defaults lambda in src/OrcaSlicer.cpp and src/slic3r/GUI/Plater.cpp that scans keys (wall_filament, sparse_infill_filament, solid_infill_filament, support_filament, support_interface_filament) on configs/objects/volumes, updates values, counts conversions and logs the result. Also adds a Semver check for "2.4.0-dev" in OrcaSlicer to trigger the migration for files older than that version. This preserves expected default filament selections when loading older project files.
* Update OrcaSlicer.cpp
* Extract migration helper to ConfigMigrations
Centralize legacy feature-filament default migration by moving the duplicated lambda into ConfigMigrations::migrate_legacy_feature_filament_defaults (src/libslic3r/Config.cpp) and declaring it in Config.hpp. Update OrcaSlicer.cpp and slic3r/GUI/Plater.cpp to call the new function instead of inline lambdas. The helper converts specific feature filament keys (wall_filament, sparse_infill_filament, solid_infill_filament, support_filament, support_interface_filament) from int 1 to 0 and returns the count of conversions to avoid duplicated migration logic.
* Remove DynamicFilamentList1Based and consolidate lists
Delete the specialized DynamicFilamentList1Based struct and its global instance. Update Choice registrations to use the single dynamic_filament_list for wall, sparse_infill and solid_infill filaments, and remove the extra update call for the removed instance. This consolidates filament choice handling and removes duplicated logic in Plater.cpp.
* move it
* fix objects
* Update Config.hpp
* Update profiles
* fix(ElegooLink): pass printer SN to CC2 device panel URL
The CC2 panel subscribes to MQTT topics keyed by the printer serial number.
Without sn= in the URL it uses a wrong hardcoded fallback SN, subscribes to
the wrong topics, and shows Offline permanently even though the printer is
reachable.
- Cache the SN in elegoo_cc2_test() (already fetches it, was discarding it)
- Look up cache in get_print_host_webui(); fall back to a short LAN HTTP
call on first use before the test has run
- Append sn= to the panel URL
- Clear the wrong hardcoded fallback SN/IP from the panel bundle
- Add a small synchronous boot script to the panel that fetches the SN
from the printer before the bundle reads URLSearchParams, as a fallback
for unpatched binaries
* fix(ElegooLink): persist CC2 serial number in AppConfig dev_sn section
Store the printer SN under [dev_sn] keyed by normalized print_host after
a successful connection test or system/info fetch. Reuse it on later
sessions before hitting the network, matching how access_code is keyed by
dev_id for other LAN printers.
* fix(ElegooLink): answer get_sn IPC instantly from dev_sn cache
The CC2 panel always calls get_sn with a 10s timeout. Remove the HTTP
fallback from get_sn() and resolve IPC from dev_sn/memory only so Device
tab load is not blocked after sn= is already in the URL.
* fix(ElegooLink): skip get_sn IPC when URL already has sn
The CC2 device panel calls get_sn with a 10s timeout on every MQTT
connect even when Orca passes sn= in the query string. Use the URL
serial immediately and only fall back to IPC when it is missing.
* refactor(ElegooLink): resolve CC2 SN via PrintHost::get_sn in GUI
Drop the ElegooLink.hpp include from PrinterWebViewHandler; the webview
IPC handler uses the existing PrintHost virtual instead. Keep CC2 serial
lookup helpers file-local in ElegooLink.cpp and share them between
get_sn() and get_print_host_webui().
* chore: drop redundant <memory> include in PrinterWebViewHandler
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Update/add re:3D profiles.
* Fix encoding issue with UTF-8 BOM
* Change spaces to tabs.
* Fix alignment-based space indentation issues.
* Test: rename_from property
* Test 2: rename_from property
* Test 3: use 'renamed' instead of 'rename'
* Add renamed property for each conflicting profile.
* Revert to optimized assets improved on [#13149](https://github.com/OrcaSlicer/OrcaSlicer/pull/13149)
* Sync Elegoo profiles from ElegooSlicer
Update vendor Elegoo.json, filament/machine/process trees, and OrcaFilamentLibrary
Elegoo entries. Align machine default material names with existing filament preset names.
* feat: expose filament_name for G-code export filename format
Derive from filament_settings_id for the first active extruder and strip the suffix after @, matching ElegooSlicer so filename_format can use {filament_name}.
* chore: reorder Elegoo entries in OrcaFilamentLibrary
Group Elegoo @base profiles and bump library version to 02.03.02.62.
* sync OrcaFilamentLibrary.json with Elegoo filament profiles
* fix: clean up Elegoo process renamed_from for profile validation
Add single renamed_from only where preset names changed from legacy Orca
names; remove duplicate Rapid @System library entries that conflicted with
ECC2 vendor presets.
* fix(profiles): add missing Elegoo renamed_from for profile validation
CI custom-preset tests still inherit legacy Orca preset names that no
longer exist after the Elegoo bundle update. Add renamed_from on process,
Neptune 4 machines, OrcaFilamentLibrary filaments, and Giga profiles so
inherits resolve again, without changing print parameters.
Update Snapmaker U1 (0.4 nozzle).json
Updated Snapmaker U1 0.4 nozzle "change_filament_gcode" and "machine_end_gcode" to fix the issue of collisions when using "Print by Object"
PR #13388 added resources/printers/N6.json for X2D support but did not
bump resources/printers/version.txt. PresetUpdater only copies files
from the install's resources/printers/ to the user's data_dir/printers/
when the resources version is newer than the user's stored version, so
every existing install stays at 02.00.00.29 and never receives N6.json.
At runtime, json_diff::load_compatible_settings("N6", "") reads from
data_dir/printers/N6.json; the silent file-missing failure leaves
is_support_bed_leveling, is_support_pa_calibration, and
SupportCalibrationNozzleOffset at their defaults, hiding the Bed
Leveling and Nozzle Offset Calibration checkboxes in the Send Print
Job dialog for the X2D.
Bumping the patch version triggers the existing propagation logic on
next startup.
Fixes#13780Fixes#13794
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* initial commit
* fix upper bounds for assemblies
* significantly less Z shift issues, still not quite tamped down yet though
* add instrumentation to logs
* finally found the issue
* update printer defaults
fix: OK/Cancel buttons clipped in Flushing Volume dialog (#13511)
The WipingDialog renders its UI inside a wxWebView. When the dialog
was clamped to screen size (many filaments, small displays, high DPI),
the HTML content exceeded the WebView bounds and the OK/Cancel buttons
fell below the visible area.
HTML fix:
- Convert .container to flexbox column with overflow-y: auto
- Pin .button-container with flex-shrink: 0 so it stays visible
- Allow .scroll-container to flex-grow for the table area
C++ fix:
- Replace heuristic extra_size with accurate fixed_overhead estimate
- Use correct cell height (25 DIP) matching HTML table row height
- Add screen margin for window decorations
- Enforce minimum dialog size when clamped
Co-authored-by: SoftFever <softfeverever@gmail.com>
* clean up UI elements
* further cleaning
* final cleanup for first round of settings UI streamlining
* update generic belt printer settings
* fix generic again
