Declare support_cooling_filter=1 on the three profiles (0.2/0.6/0.8
variants inherit from 0.4) and insert the cooling-filter conditional
into the H2D and H2S machine start g-code, inside the low-chamber-temp
airduct branch:
{if(cooling_filter_enabled)} M145.2 P0 F0 {else} M145.2 P0 F1 {endif}
H2D Pro intentionally gets no g-code edit: its duct firmware takes the
filter mode over the device channel only, so the flag merely enables
the toggle.
Impact on existing users at default settings: H2D/H2S start g-code gains
exactly one line (M145.2 P0 F1, filter off) in the cool-chamber branch;
nothing is removed or reordered. The existing support_air_filtration=1
overrides are deliberately kept so exhaust-fan behavior for ABS-class
filaments is unchanged, even though the machine-tab row is hidden while
the cooling-filter toggle is shown.
cooling_filter_enabled existed as a config option but was shown nowhere,
and there was no capability flag to gate it. The cooling filter and air
filtration are alternative accessories sharing the same duct, so a
printer declares one or the other.
- new hidden printer capability flag support_cooling_filter
- "Use cooling filter" toggle in the Accessory group, shown only when
the printer supports it; the air-filtration toggle hides in that case
(no vendor restriction: third-party printers keep air filtration)
- explicit defaults (0) in the common machine base
- H2C declares support_cooling_filter=1 instead of support_air_filtration;
its start-gcode already carries the cooling-filter conditional, so the
toggle is functional. On H2C this drops the two exhaust-fan lines that
air filtration emitted for ABS-class filaments, matching the printer's
actual duct accessory; H2C is new on this branch so no existing user
output changes.
Printers without the flag keep exactly the previous accessory UI and
g-code.
New printer option fan_direction (undefine/left/right/both, default
undefine) declares which side the auxiliary part-cooling airflow comes
from. When set and the printer has an auxiliary fan, auto-orient adds a
yaw rotation so the dominant overhang area faces the airflow, and newly
added primitive shapes are pre-oriented the same way (except the Cube,
whose axis-aligned bounding box the pressure-advance pattern calibration
depends on).
- FanDirection enum + fan_direction printer option (Accessory group,
enabled only with auxiliary_fan)
- orient engine: weighted overhang areas per candidate, yaw-direction
search, vertical rotation applied on top of the primary orientation;
the cooling weights are taken from the candidate actually chosen,
including the flat-bottom tie-break
- orient_for_cooling() for primitive placement
- set fan_direction=left on H2C/H2D/H2D Pro/X1/X1E/P1S 0.4 profiles
(X1C/H2S/P2S/X2D/Qidi X-Max 4 already carried the key, which now
takes effect)
With fan_direction unset or no auxiliary fan the vertical rotation stays
identity and auto-orient results are unchanged; slicing and g-code are
never affected.
The engine already implements prime_volume_mode (Default/Saving/Fast)
but nothing in the UI could set it, leaving prime-saving unreachable on
multi-sub-nozzle extruders and fast purge unreachable on printers that
support it.
- new PurgeModeDialog with selectable Standard/Fast or
Standard/Prime Saving cards depending on printer capability
- "Purge mode" sidebar button next to Flushing volumes; opens the
dialog and stores the choice in the project config
- printer preset-load gating: button shown only when the printer has
multiple sub-nozzles per extruder or sets support_fast_purge_mode;
stale project values the printer cannot honor reset to Default
- enable fast purge on A2L 0.4 (support_fast_purge_mode), explicit
default 0 in the common machine base
- new dialog strings added to OrcaSlicer.pot
Printers without these capabilities never show the button and their
projects keep prime_volume_mode at Default, so slicing output is
unchanged.
Enable air filtration support in affected system printer profiles
Some system printer profiles that support air filtration had the feature
incorrectly disabled in the printer settings.
This caused the related filament settings to be hidden, making the feature
unavailable to users even though it is supported by the printer.
Enable "support_air_filtration" in affected system printer profiles and
bump profile version thus forcing Orca to refresh cached settings.
This ensures air filtration settings are visible and usable on printers
that support the feature.
* Disable arc fitting by default on BBL P2S
* Update BBL P2S printer profile
* bump the version so that it automatically update the cache
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
Reduce the size of current and new JSONs by standardising them with 1 tab indentation instead of 4 spaces.
This effectively reduces the size by almost 20 MB.
| Current | New |
|---|---|
| 85.2 Mib | 67 Mib |
Used [JQ](https://jqlang.org/) `--tab` to automatically format every current JSON.
> [!NOTE]
> Some profiles had the arrays on the same line, but those created by Orca were in the standard format (each object below the previous one). In some cases, this increases the number of tabs due to the new lines, but the increase is negligible, and this way both the base profiles and those created by Orca maintain the same style.
* Updated profile to match latest officlal BBL tweaks
Updated the profile for the P2S with several changes to match the latest machine gcode changes made by BBL:
- Added Ventobox support
- Added air purification at the end of the print. When exhaust fan controls are setup in the filament profile, this is skipped
- Disabled auxiliary_fan by default to fix the issue that it overrides auto cooling and heating managed by the printer. Enabling this in printer settings makes it behave as before if so desired
- Updated with other tweaks made by BBL
* Reverted one line in layer change code
Reverted one line in layer change gcode as it was causing issues and was bambu studio specific anyway. Filament change works exactly as expected now.
* Re-enabled soaking time
This was a personal change that sneaked in, but may be unwanted for other users who have been using Orca for this printer for a while.
* Fixed redundant homing command and moved enable input shaping up
Fixed some issues BBL made in their original startup code that executes one redundant homing command for people who disable ABL. Also moved up the enable input shaping command to make the startup sequence quieter.
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Emit Disable Power Loss Recovery
Now only works if it's enabled but the goal it's to force disable it.
With this change it will always emit the command for BBL or Marlin 2.
Co-Authored-By: Michael Rook <54159303+michaelr0@users.noreply.github.com>
* Refactor power loss recovery G-code comments
* Return empty power loss recovery when no compatible printer
* Update power loss recovery comments
Update label and tooltip for power loss recovery
* Add enum for power loss recovery mode
Refactored power loss recovery configuration to use a new PowerLossRecoveryMode enum instead of a boolean. Updated GCodeWriter and related logic to handle the new enum, allowing for 'printer_configuration', 'enable', and 'disable' options. Updated config handling, legacy value conversion, and default values accordingly.
* Update PrintConfig.cpp
---------
Co-authored-by: Michael Rook <54159303+michaelr0@users.noreply.github.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Add ability to disable Power Loss Recovery
* Fix typo in PrintConfig.hpp for power loss recovery
* Attempt to resolve Unknown option exception: disable_power_less_recovery
Add disable_power_loss_recovery property to any json which had scan_first_layer
* Revert "Attempt to resolve Unknown option exception: disable_power_less_recovery"
This reverts commit ddaf34b317.
* Fix typo
* Change attribution from BBS to Orca in PrintConfig.cpp
* Mini refactor power loss recovery handling in GCode export
- Moved power loss recovery G-code generation to a new method in GCodeWriter.
- Support Marlin 2
* Update comments and power loss recovery handling
* Implement power loss recovery G-code commands
Added functions to start and end power loss recovery with appropriate G-code commands and comments.
* Add power loss recovery methods to GCodeWriter
* refactor and fix build errors
---------
Co-authored-by: Michael Rook <michael@rook.id.au>
Co-authored-by: Ioannis Giannakas <59056762+igiannakas@users.noreply.github.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
This reverts commit 4f8d3466508f3706e8d3f656294f7c5d3a9a7f88.
Reason for revert: use another method
Change-Id: I2a6465ea507f15ce200ea9cf03994b18bb2f257f
(cherry picked from commit 630248ae566c8cf8c61ceacb74ae3cd31d9e1501)
This reverts commit 576444e746f4de3ab71c91b8a66fa4a64c3427c8.
Reason for revert: <remove high flow of X/P>
Change-Id: I875f649c62d503bdf1321b5fec829bb190b02bce
(cherry picked from commit 0b46acb8e793af883b797f83a9ad72a55dd69f3e)
Modify the machine start gcode for nozzle diameters 0.2, 0.4, 0.6, and 0.8 on the X1, X1 Carbon, and X1E models to move the compensation lines closer to the edge.
jira: STUDIO-14317
Change-Id: Ib0662d5cf9dfd63b960fcb7c458fa35dc0954c1b
(cherry picked from commit 6aaa7ae4ffd2c893ed41a5eed51a6a7dd2d83f7b)
(cherry picked from commit 62bcdd5b1627526035ce3f23ca9999b958fd05b2)
The configuration changes that were previously reverted are now reintegrated
jira: none
Change-Id: I82148ddb9688ffb358018c187ed71accad47529c
(cherry picked from commit 55fad607fd4e66b6b44b1b11b67f8cc5141c3af6)
