mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-09-24 17:26:47 +00:00
226e95f734
Adds the LulzBot Mini 1 (single extruder, 0.5 mm nozzle, 2.85 mm filament)
to the existing Lulzbot vendor, which previously shipped only TAZ models.
Values are taken from LulzBot's own current slicer configuration
(github.com/lulzbot3d/CuraLE) rather than estimated:
- geometry and custom g-code from resources/definitions/single_mini_mini_1.def.json
and resources/gcodes/mini_1/{mini_1_start,mini_1_end}.gcode
- filament temperatures and cooling from resources/materials/*.xml.fdm_material,
overridden by resources/quality/single_mini/<material>/*.inst.cfg
The start g-code reproduces the Mini's nozzle wipe and four-washer G29 probe,
with the filament-type temperature conditionals used by the sibling TAZ profiles.
One deliberate departure from current CuraLE: the pre-wipe retract is 30 mm,
the value used by Cura LE 4.13.x, rather than the 4 mm current CuraLE uses.
The Mini probes by electrical contact between nozzle and washer, so the nozzle
must stay clean through the wipe and all four touches. At 4 mm the melt zone
stays full and can ooze onto a washer, which caused auto-levelling failures on
hardware; 30 mm empties it. The cost is a ~24 s purge at print start.
The three filament presets follow docs/HLSD/filament_id.md rule 4: a vendor
tuning a generic material inherits Generic X @System, keeps the Generic X base
name and declares no filament_id, so identity stays with OrcaFilamentLibrary.
Their compatible_printers is the Mini alone, disjoint from Generic X @Lulzbot
(TAZ only) as rule 3 requires. They exist because temperature is a filament-scope
setting, so LulzBot's values need printer-scoped presets. All six plate types
carry the same temperature, because the Mini has a single bed and curr_bed_type
can hold a stale value carried over from another printer.
Strictly additive: no existing profile is modified, so TAZ behaviour is
unchanged and no migration is required. Lulzbot.json is bumped to 02.04.00.05.
Verified with scripts/orca_profile_tool.py check and scripts/check_profile.sh
on the full tree (profile tool, system validation, slice, filament subtypes and
custom-preset fixtures all pass), by diffing sliced output against LulzBot's own
Cura LE g-code for the same model and filament (temps, retraction, speeds and
the full wipe/probe sequence match), and by printing a 3DBenchy on a Mini 1 over
OctoPrint.
Claude-Session: https://claude.ai/code/session_012aLyqsXB7FKqwQdE2QF7Et
Co-authored-by: Claude Opus 5 <noreply@anthropic.com>
Co-authored-by: SoftFever <103989404+SoftFever@users.noreply.github.com>
109 lines
3.2 KiB
JSON
109 lines
3.2 KiB
JSON
{
|
|
"type": "process",
|
|
"name": "0.25mm Standard @Lulzbot Mini 1",
|
|
"inherits": "fdm_process_common",
|
|
"from": "system",
|
|
"setting_id": "bqY8CEHwvUYnLRPe",
|
|
"instantiation": "true",
|
|
"reduce_crossing_wall": "0",
|
|
"layer_height": "0.25",
|
|
"max_travel_detour_distance": "0",
|
|
"bottom_surface_pattern": "monotonic",
|
|
"bottom_shell_layers": "5",
|
|
"bottom_shell_thickness": "0",
|
|
"bridge_flow": "0.85",
|
|
"bridge_speed": "25",
|
|
"brim_width": "0",
|
|
"brim_object_gap": "0",
|
|
"compatible_printers_condition": "",
|
|
"print_sequence": "by layer",
|
|
"default_acceleration": "0",
|
|
"outer_wall_acceleration": "0",
|
|
"top_surface_acceleration": "0",
|
|
"bridge_no_support": "0",
|
|
"draft_shield": "disabled",
|
|
"elefant_foot_compensation": "0.1",
|
|
"enable_arc_fitting": "0",
|
|
"outer_wall_line_width": "0.5",
|
|
"wall_infill_order": "inner wall/outer wall/infill",
|
|
"line_width": "0.5",
|
|
"infill_direction": "45",
|
|
"sparse_infill_density": "20%",
|
|
"sparse_infill_pattern": "crosshatch",
|
|
"initial_layer_acceleration": "0",
|
|
"travel_acceleration": "0",
|
|
"inner_wall_acceleration": "0",
|
|
"initial_layer_line_width": "0.50",
|
|
"initial_layer_print_height": "0.425",
|
|
"infill_combination": "0",
|
|
"sparse_infill_line_width": "0.50",
|
|
"infill_wall_overlap": "25%",
|
|
"interface_shells": "0",
|
|
"ironing_flow": "15%",
|
|
"ironing_spacing": "0.1",
|
|
"ironing_speed": "15",
|
|
"ironing_type": "no ironing",
|
|
"reduce_infill_retraction": "1",
|
|
"filename_format": "{input_filename_base}_{filament_type[initial_tool]}_{print_time}.gcode",
|
|
"detect_overhang_wall": "1",
|
|
"overhang_1_4_speed": "0",
|
|
"overhang_2_4_speed": "20",
|
|
"overhang_3_4_speed": "15",
|
|
"overhang_4_4_speed": "10",
|
|
"inner_wall_line_width": "0.50",
|
|
"wall_loops": "2",
|
|
"print_settings_id": "",
|
|
"raft_layers": "0",
|
|
"seam_position": "aligned",
|
|
"skirt_distance": "3",
|
|
"skirt_height": "1",
|
|
"skirt_loops": "2",
|
|
"minimum_sparse_infill_area": "10",
|
|
"internal_solid_infill_line_width": "0",
|
|
"spiral_mode": "0",
|
|
"standby_temperature_delta": "-5",
|
|
"enable_support": "0",
|
|
"resolution": "0.012",
|
|
"support_type": "normal(auto)",
|
|
"support_style": "grid",
|
|
"support_on_build_plate_only": "0",
|
|
"support_top_z_distance": "0.19",
|
|
"support_filament": "0",
|
|
"support_line_width": "0.5",
|
|
"support_interface_loop_pattern": "0",
|
|
"support_interface_filament": "0",
|
|
"support_interface_top_layers": "3",
|
|
"support_interface_bottom_layers": "-1",
|
|
"support_interface_spacing": "0.2",
|
|
"support_interface_speed": "100%",
|
|
"support_base_pattern": "rectilinear",
|
|
"support_base_pattern_spacing": "0.2",
|
|
"support_speed": "40",
|
|
"support_threshold_angle": "30",
|
|
"support_object_xy_distance": "60%",
|
|
"tree_support_branch_angle": "40",
|
|
"tree_support_wall_count": "0",
|
|
"detect_thin_wall": "1",
|
|
"top_surface_pattern": "monotonicline",
|
|
"top_surface_line_width": "0.5",
|
|
"top_shell_layers": "5",
|
|
"top_shell_thickness": "1.0",
|
|
"initial_layer_speed": "35%",
|
|
"initial_layer_infill_speed": "35%",
|
|
"outer_wall_speed": "40",
|
|
"inner_wall_speed": "45",
|
|
"internal_solid_infill_speed": "40",
|
|
"top_surface_speed": "30",
|
|
"gap_infill_speed": "30",
|
|
"sparse_infill_speed": "60",
|
|
"travel_speed": "175",
|
|
"enable_prime_tower": "1",
|
|
"wipe_tower_no_sparse_layers": "0",
|
|
"prime_tower_width": "30",
|
|
"xy_hole_compensation": "0",
|
|
"xy_contour_compensation": "0",
|
|
"compatible_printers": [
|
|
"Lulzbot Mini 1 0.5 nozzle"
|
|
]
|
|
}
|