OrcaSlicer/src/libslic3r/Support/SupportSpotsGenerator.hpp

#ifndef SRC_LIBSLIC3R_SUPPORTABLEISSUESSEARCH_HPP_
#define SRC_LIBSLIC3R_SUPPORTABLEISSUESSEARCH_HPP_

#include "PrintConfig.hpp"
#include "MaterialType.hpp"
#include <boost/log/trivial.hpp>
#include <cstddef>
#include <string>
#include <utility>
#include <vector>

namespace Slic3r { class Layer; }


namespace Slic3r {

namespace SupportSpotsGenerator {

struct Params
{
    Params(
        const std::vector<std::string> &filament_types/*, float max_acceleration*/, int raft_layers_count, BrimType brim_type, float brim_width)
        : /*max_acceleration(max_acceleration), */raft_layers_count(raft_layers_count), brim_type(brim_type), brim_width(brim_width)
    {
        if (filament_types.size() > 1) {
            BOOST_LOG_TRIVIAL(debug)
                << "SupportSpotsGenerator does not currently handle different materials properly, only first will be used";
        }
        if (filament_types.empty() || filament_types[0].empty()) {
            BOOST_LOG_TRIVIAL(error) << "SupportSpotsGenerator error: empty filament_type";
            filament_type = std::string("PLA");
        } else {
            filament_type = filament_types[0];
            BOOST_LOG_TRIVIAL(debug) << "SupportSpotsGenerator: applying filament type: " << filament_type;
        }
    }

    // the algorithm should use the following units for all computations: distance [mm], mass [g], time [s], force [g*mm/s^2]
    const float bridge_distance = 16.0f; // mm
    // const float max_acceleration; // mm/s^2 ; max acceleration of object in XY -- should be applicable only to printers with bed slinger, 
    //                               // however we do not have such info yet. The force is usually small anyway, so not such a big deal to include it everytime
    const int raft_layers_count;
    std::string filament_type;

    BrimType brim_type;
    const float brim_width;

    const std::pair<float,float> malformation_distance_factors = std::pair<float, float> { 0.2, 1.1 };
    const float max_curled_height_factor = 10.0f;
    const float curled_distance_expansion = 1.0f; // controls the spread of the area where slow down for curled overhangs is applied
    const float curling_tolerance_limit = 0.1f;

    const float min_distance_between_support_points = 3.0f; //mm
    const float support_points_interface_radius = 1.5f; // mm
    const float min_distance_to_allow_local_supports = 1.0f; //mm

    const float gravity_constant = 9806.65f; // mm/s^2; gravity acceleration on Earth's surface, algorithm assumes that printer is in upwards position.
    const double filament_density = 1.25e-3f; // g/mm^3  ; Common filaments are very lightweight, so precise number is not that important
    const double material_yield_strength = 33.0f * 1e6f; // (g*mm/s^2)/mm^2; 33 MPa is yield strength of ABS, which has the lowest yield strength from common materials.
    const float standard_extruder_conflict_force = 10.0f * gravity_constant; // force that can occasionally push the model due to various factors (filament leaks, small curling, ... );
    const float malformations_additive_conflict_extruder_force = 65.0f * gravity_constant; // for areas with possible high layered curled filaments

    // MPa * 1e^6 = (g*mm/s^2)/mm^2 = g/(mm*s^2); yield strength of the bed surface
    double get_bed_adhesion_yield_strength() const {
        if (raft_layers_count > 0) {
            return get_support_spots_adhesion_strength() * 2.0;
        }

    double yield_strength = 0.02;
    MaterialType::get_yield_strength(filament_type, yield_strength);
        return yield_strength * 1e6;
    }

    double get_support_spots_adhesion_strength() const {
         return 0.016f * 1e6; 
    }
};

void estimate_malformations(std::vector<Layer *> &layers, const Params &params);


enum class SupportPointCause { 
    LongBridge, // point generated on bridge and straight perimeter extrusion longer than the allowed length 
    FloatingBridgeAnchor, // point generated on unsupported bridge endpoint
    FloatingExtrusion, // point generated on extrusion that does not hold on its own
    SeparationFromBed, // point generated for object parts that are connected to the bed, but the area is too small and there is a risk of separation (brim may help)
    UnstableFloatingPart, // point generated for object parts not connected to the bed, holded only by the other support points (brim will not help here)
    WeakObjectPart // point generated when some part of the object is too weak to hold the upper part and may break (imagine hourglass)
    };

// The support points can be sorted into two groups
// 1. Local extrusion support for extrusions that are printed in the air and would not
//    withstand on their own (too long bridges, sharp turns in large overhang, concave bridge holes, etc.)
//    These points have negative force (-EPSILON) and Vec2f::Zero() direction
//    The algorithm still expects that these points will be supported and accounts for them in the global stability check.
// 2. Global stability support points are generated at each spot, where the algorithm detects that extruding the current line
//    may cause separation of the object part from the bed and/or its support spots or crack in the weak connection of the object parts.
//    The generated point's direction is the estimated falling direction of the object part, and the force is equal to te difference
//    between forces that destabilize the object (extruder conflicts with curled filament, weight if instable center of mass, bed movements etc)
//    and forces that stabilize the object (bed adhesion, other support spots adhesion, weight if stable center of mass).
//    Note that the force is only the difference - the amount needed to stabilize the object again.
/*struct SupportPoint
{
    SupportPoint(SupportPointCause cause, const Vec3f &position, float force, float spot_radius, const Vec2f &direction)
        : cause(cause), position(position), force(force), spot_radius(spot_radius), direction(direction)
    {}

    bool is_local_extrusion_support() const
    {
        return cause == SupportPointCause::LongBridge || cause == SupportPointCause::FloatingExtrusion;
    }
    bool is_global_object_support() const { return !is_local_extrusion_support(); }

    SupportPointCause cause; // reason why this support point was generated. Used for the user alerts
    // position is in unscaled coords. The z coordinate is aligned with the layers bottom_z coordiantes
    Vec3f position;
    // force that destabilizes the object to the point of falling/breaking. g*mm/s^2 units
    // It is valid only for global_object_support. For local extrusion support points, the force is -EPSILON
    // values gathered from large XL model: Min : 0 | Max : 18713800 | Average : 1361186 | Median : 329103
    // For reference 18713800 is weight of 1.8 Kg object, 329103 is weight of 0.03 Kg
    // The final sliced object weight was approx 0.5 Kg
    float force;
    // Expected spot size. The support point strength is calculated from the area defined by this value.
    // Currently equal to the support_points_interface_radius parameter above
    float spot_radius;
    // direction of the fall of the object (z part is neglected)
    Vec2f direction;
};

using SupportPoints = std::vector<SupportPoint>;

struct Malformations {
    std::vector<Lines> layers; //for each layer
};

struct PartialObject
{
    PartialObject(Vec3f centroid, float volume, bool connected_to_bed)
        : centroid(centroid), volume(volume), connected_to_bed(connected_to_bed)
    {}

    Vec3f centroid;
    float volume;
    bool  connected_to_bed;
};

using PartialObjects = std::vector<PartialObject>;

std::tuple<SupportPoints, PartialObjects> full_search(const PrintObject *po, const PrintTryCancel& cancel_func, const Params &params);

void estimate_supports_malformations(std::vector<SupportLayer *> &layers, float supports_flow_width, const Params &params);


// NOTE: the boolean marks if the issue is critical or not for now.
std::vector<std::pair<SupportPointCause, bool>> gather_issues(const SupportPoints &support_points,
                                                             PartialObjects      &partial_objects);
*/
}} // namespace Slic3r::SupportSpotsGenerator

#endif /* SRC_LIBSLIC3R_SUPPORTABLEISSUESSEARCH_HPP_ */