mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-05-16 18:12:10 +00:00
16727644bb
Reduce the size of current and new JSONs by standardising them with 1 tab indentation instead of 4 spaces. This effectively reduces the size by almost 20 MB. | Current | New | |---|---| | 85.2 Mib | 67 Mib | Used [JQ](https://jqlang.org/) `--tab` to automatically format every current JSON. > [!NOTE] > Some profiles had the arrays on the same line, but those created by Orca were in the standard format (each object below the previous one). In some cases, this increases the number of tabs due to the new lines, but the increase is negligible, and this way both the base profiles and those created by Orca maintain the same style.
41 lines
2.1 KiB
JSON
41 lines
2.1 KiB
JSON
{
|
|
"type": "machine",
|
|
"name": "Geeetech Mizar 0.4 nozzle",
|
|
"inherits": "fdm_geeetech_common",
|
|
"from": "system",
|
|
"setting_id": "GM_GEEETECH_006",
|
|
"instantiation": "true",
|
|
"printer_model": "Geeetech Mizar",
|
|
"default_filament_profile": [
|
|
"Generic PLA @System"
|
|
],
|
|
"printer_variant": "0.4",
|
|
"default_print_profile": "0.20mm Standard @Geeetech common",
|
|
"nozzle_diameter": [
|
|
"0.4"
|
|
],
|
|
"extruder_type": [
|
|
"Bowden"
|
|
],
|
|
"max_layer_height": [
|
|
"0.3"
|
|
],
|
|
"min_layer_height": [
|
|
"0.07"
|
|
],
|
|
"printable_area": [
|
|
"0x0",
|
|
"220x0",
|
|
"220x220",
|
|
"0x220"
|
|
],
|
|
"printable_height": "260",
|
|
"retract_lift_below": [
|
|
"259"
|
|
],
|
|
"machine_start_gcode": ";Geeetech Official open-source firmware for Mizar: https://github.com/Geeetech3D/Mizar \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0",
|
|
"machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors",
|
|
"nozzle_type": "brass",
|
|
"auxiliary_fan": "0"
|
|
}
|