{
    "type": "filament",
    "name": "Generic PC @K2 Plus-all",
    "inherits": "fdm_filament_pc",
    "from": "system",
    "setting_id": "GFSA04",
    "instantiation": "true",
    "activate_air_filtration": [
        "0"
    ],
    "additional_cooling_fan_speed": [
        "0"
    ],
    "close_fan_the_first_x_layers": [
        "3"
    ],
    "complete_print_exhaust_fan_speed": [
        "80"
    ],
    "cool_plate_temp": [
        "110"
    ],
    "cool_plate_temp_initial_layer": [
        "110"
    ],
    "during_print_exhaust_fan_speed": [
        "60"
    ],
    "eng_plate_temp": [
        "105"
    ],
    "eng_plate_temp_initial_layer": [
        "105"
    ],
    "filament_cost": [
        "100"
    ],
    "filament_density": [
        "1.18"
    ],
    "filament_deretraction_speed": [
        "nil"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_flow_ratio": [
        "0.95"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_max_volumetric_speed": [
        "16"
    ],
    "filament_minimal_purge_on_wipe_tower": [
        "15"
    ],
    "filament_retract_before_wipe": [
        "nil"
    ],
    "filament_retract_restart_extra": [
        "nil"
    ],
    "filament_retract_when_changing_layer": [
        "nil"
    ],
    "filament_retraction_length": [
        "nil"
    ],
    "filament_retraction_minimum_travel": [
        "nil"
    ],
    "filament_retraction_speed": [
        "nil"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_vendor": [
        "Generic"
    ],
    "filament_wipe": [
        "nil"
    ],
    "filament_wipe_distance": [
        "nil"
    ],
    "filament_z_hop": [
        "nil"
    ],
    "filament_z_hop_types": [
        "nil"
    ],
    "full_fan_speed_layer": [
        "0"
    ],
    "nozzle_temperature": [
        "260"
    ],
    "nozzle_temperature_initial_layer": [
        "260"
    ],
    "nozzle_temperature_range_high": [
        "270"
    ],
    "nozzle_temperature_range_low": [
        "250"
    ],
    "required_nozzle_HRC": [
        "0"
    ],
    "slow_down_for_layer_cooling": [
        "1"
    ],
    "slow_down_layer_time": [
        "12"
    ],
    "temperature_vitrification": [
        "110"
    ],
    "filament_start_gcode": [
        "; filament start gcode\n{if (layer_z > first_layer_height) }\nM104 S[nozzle_temperature]\n{else} \nM104 S[first_layer_temperature]\n{endif}"
    ],
    "filament_end_gcode": [
        ";filament end gcode \n"
    ],
    "activate_chamber_layer": "2",
    "activate_chamber_temp_control": "1",
    "chamber_temperature": "50",
    "cool_cds_fan_start_at_height": "0.5",
    "cool_special_cds_fan_speed": "0",
    "default_filament_colour": "\"\"",
    "enable_overhang_bridge_fan": "1",
    "enable_pressure_advance": "0",
    "enable_special_area_additional_cooling_fan": "0",
    "epoxy_resin_plate_temp": "0",
    "epoxy_resin_plate_temp_initial_layer": "0",
    "filament_cooling_final_speed": "3.4",
    "filament_cooling_initial_speed": "2.2",
    "filament_cooling_moves": "4",
    "filament_load_time": "0",
    "filament_loading_speed": "28",
    "filament_loading_speed_start": "3",
    "filament_multitool_ramming": "0",
    "filament_multitool_ramming_flow": "10",
    "filament_multitool_ramming_volume": "10",
    "filament_notes": "\"\"",
    "filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
    "filament_retract_lift_above": "nil",
    "filament_retract_lift_below": "nil",
    "filament_retract_lift_enforce": "nil",
    "filament_shrink": "100%",
    "filament_toolchange_delay": "0",
    "filament_unload_time": "0",
    "filament_unloading_speed": "90",
    "filament_unloading_speed_start": "100",
    "material_flow_dependent_temperature": "0",
    "pressure_advance": "0.03",
    "support_material_interface_fan_speed": "-1",
    "compatible_printers": [
        "Creality K2 Plus 0.4 nozzle"
    ],
    "filament_id": "00021"
}