{
	"type": "filament",
	"name": "Snapmaker PETG HF @U1 base2",
	"inherits": "fdm_filament_petg",
	"from": "system",
	"filament_id": "GFG96",
	"instantiation": "false",
	"cool_plate_temp": [
		"0"
	],
	"cool_plate_temp_initial_layer": [
		"0"
	],
	"eng_plate_temp": [
		"70"
	],
	"eng_plate_temp_initial_layer": [
		"70"
	],
	"filament_type": [
		"PETG"
	],
	"fan_cooling_layer_time": [
		"30"
	],
	"fan_max_speed": [
		"40"
	],
	"filament_cost": [
		"24.99"
	],
	"filament_density": [
		"1.28"
	],
	"filament_flow_ratio": [
		"0.95"
	],
	"filament_max_volumetric_speed": [
		"16"
	],
	"hot_plate_temp": [
		"70"
	],
	"hot_plate_temp_initial_layer": [
		"70"
	],
	"nozzle_temperature_range_high": [
		"270"
	],
	"nozzle_temperature": [
		"220"
	],
	"nozzle_temperature_initial_layer": [
		"220"
	],
	"overhang_fan_speed": [
		"90"
	],
	"overhang_fan_threshold": [
		"10%"
	],
	"slow_down_layer_time": [
		"25"
	],
	"textured_plate_temp": [
		"70"
	],
	"textured_plate_temp_initial_layer": [
		"70"
	],
	"filament_start_gcode": [
		"; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
	],
	"activate_air_filtration": [
		"0"
	],
	"additional_cooling_fan_speed": [
		"0"
	],
	"chamber_temperatures": [
		"0"
	],
	"close_fan_the_first_x_layers": [
		"3"
	],
	"complete_print_exhaust_fan_speed": [
		"70"
	],
	"counter_coef_1": [
		"0"
	],
	"counter_coef_2": [
		"0.008"
	],
	"counter_coef_3": [
		"-0.041"
	],
	"counter_limit_min": [
		"-0.035"
	],
	"counter_limit_max": [
		"0.033"
	],
	"circle_compensation_speed": [
		"200"
	],
	"during_print_exhaust_fan_speed": [
		"70"
	],
	"diameter_limit": [
		"50"
	],
	"fan_min_speed": [
		"20"
	],
	"filament_cooling_before_tower": [
		"0"
	],
	"filament_dev_ams_drying_ams_limitations": [
		"0"
	],
	"filament_dev_ams_drying_temperature": [
		"40.0"
	],
	"filament_dev_ams_drying_time": [
		"8.0"
	],
	"filament_dev_drying_softening_temperature": [
		"40.0"
	],
	"filament_dev_ams_drying_heat_distortion_temperature": [
		"45.0"
	],
	"filament_dev_drying_cooling_temperature": [
		"35.0"
	],
	"filament_dev_chamber_drying_bed_temperature": [
		"90.0"
	],
	"filament_dev_chamber_drying_time": [
		"12.0"
	],
	"filament_flush_temp": [
		"0"
	],
	"filament_flush_volumetric_speed": [
		"0"
	],
	"filament_long_retractions_when_cut": [
		"nil"
	],
	"filament_long_retractions_when_ec": [
		"nil"
	],
	"filament_ramming_volumetric_speed": [
		"-1"
	],
	"filament_ramming_volumetric_speed_nc": [
		"-1"
	],
	"filament_minimal_purge_on_wipe_tower": [
		"15"
	],
	"filament_printable": [
		"3"
	],
	"filament_retraction_distances_when_cut": [
		"nil"
	],
	"filament_retraction_distances_when_ec": [
		"nil"
	],
	"filament_retraction_length": [
		"nil"
	],
	"filament_retraction_minimum_travel": [
		"nil"
	],
	"filament_vendor": [
		"Generic"
	],
	"filament_prime_volume": [
		"45"
	],
	"filament_prime_volume_nc": [
		"60"
	],
	"filament_extruder_variant": [
		"Direct Drive Standard"
	],
	"filament_scarf_seam_type": [
		"none"
	],
	"filament_scarf_height": [
		"10%"
	],
	"filament_scarf_gap": [
		"0%"
	],
	"filament_scarf_length": [
		"10"
	],
	"filament_shrink": [
		"100%"
	],
	"filament_pre_cooling_temperature": [
		"0"
	],
	"filament_pre_cooling_temperature_nc": [
		"0"
	],
	"filament_ramming_travel_time": [
		"0"
	],
	"filament_ramming_travel_time_nc": [
		"0"
	],
	"filament_retract_length_nc": [
		"14"
	],
	"hole_coef_1": [
		"0"
	],
	"hole_coef_2": [
		"-0.008"
	],
	"hole_coef_3": [
		"0.23415"
	],
	"hole_limit_min": [
		"0.088"
	],
	"hole_limit_max": [
		"0.22"
	],
	"impact_strength_z": [
		"10"
	],
	"long_retractions_when_ec": [
		"0"
	],
	"retraction_distances_when_ec": [
		"0"
	],
	"supertack_plate_temp": [
		"70"
	],
	"supertack_plate_temp_initial_layer": [
		"70"
	],
	"no_slow_down_for_cooling_on_outwalls": [
		"0"
	],
	"slow_down_min_speed": [
		"10"
	],
	"temperature_vitrification": [
		"70"
	],
	"filament_change_length": [
		"10"
	],
	"filament_velocity_adaptation_factor": [
		"1"
	],
	"compatible_printers": [],
	"filament_end_gcode": [
		"; filament end gcode \n\n"
	],
	"filament_adaptive_volumetric_speed": [
		"0"
	],
	"volumetric_speed_coefficients": [
		"0 0 0 0 0 0"
	],
	"filament_adhesiveness_category": [
		"300"
	]
}