{
	"type": "filament",
	"name": "PolyLite CosPLA @base",
	"inherits": "fdm_filament_pla",
	"from": "system",
	"filament_id": "OFJgijky",
	"instantiation": "false",
	"bed_type": [
		"Cool Plate"
	],
	"cool_plate_temp": [
		"60"
	],
	"cool_plate_temp_initial_layer": [
		"60"
	],
	"eng_plate_temp": [
		"60"
	],
	"eng_plate_temp_initial_layer": [
		"60"
	],
	"filament_cost": [
		"20.99"
	],
	"filament_flow_ratio": [
		"0.95"
	],
	"filament_max_volumetric_speed": [
		"16"
	],
	"filament_vendor": [
		"Polymaker"
	],
	"hot_plate_temp": [
		"60"
	],
	"hot_plate_temp_initial_layer": [
		"60"
	],
	"nozzle_temperature": [
		"230"
	],
	"nozzle_temperature_initial_layer": [
		"230"
	],
	"nozzle_temperature_range_high": [
		"230"
	],
	"overhang_fan_speed": [
		"75"
	],
	"slow_down_layer_time": [
		"5"
	],
	"slow_down_min_speed": [
		"5"
	],
	"temperature_vitrification": [
		"59"
	],
	"textured_plate_temp": [
		"60"
	],
	"textured_plate_temp_initial_layer": [
		"60"
	],
	"filament_type": [
		"PLA"
	],
	"close_additional_fan_first_x_layers": [
		"3"
	],
	"retraction_distances_when_ec": [
		"0"
	],
	"filament_start_gcode": [
		"; filament start gcode\n{if  (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255\n{elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
	],
	"filament_end_gcode": [
		"; filament end gcode \n\n"
	],
	"volumetric_speed_coefficients": [
		"0 0 0 0 0 0"
	],
	"filament_adhesiveness_category": [
		"100"
	],
	"filament_dev_chamber_drying_bed_temperature": [
		"70"
	],
	"filament_dev_ams_drying_time": [
		"12",
		"12",
		"12",
		"12"
	],
	"filament_dev_ams_drying_ams_limitations": [
		"1",
		"0"
	],
	"filament_dev_ams_drying_heat_distortion_temperature": [
		"45"
	],
	"filament_dev_drying_cooling_temperature": [
		"45"
	],
	"filament_dev_ams_drying_temperature": [
		"45",
		"45",
		"45",
		"45"
	],
	"filament_dev_drying_softening_temperature": [
		"50"
	]
}