{
	"type": "filament",
	"name": "Snapmaker PLA-CF @U1 0.8 nozzle",
	"inherits": "fdm_filament_pla",
	"from": "system",
	"setting_id": "fhhnfJm4dN9FXpWQ",
	"filament_id": "OFhQf8ou",
	"instantiation": "true",
	"compatible_printers": [
		"Snapmaker U1 (0.8 nozzle)"
	],
	"enable_pressure_advance": [
		"0",
		"1"
	],
	"filament_end_gcode": [
		""
	],
	"filament_multitool_ramming": [
		"1",
		"1"
	],
	"filament_multitool_ramming_flow": [
		"25",
		"25"
	],
	"filament_start_gcode": [
		""
	],
	"filament_vendor": [
		"Snapmaker"
	],
	"textured_plate_temp": [
		"65"
	],
	"textured_plate_temp_initial_layer": [
		"65"
	],
	"hot_plate_temp": [
		"65"
	],
	"hot_plate_temp_initial_layer": [
		"65"
	],
	"filament_flow_ratio": [
		"0.98",
		"0.98"
	],
	"filament_max_volumetric_speed": [
		"18",
		"18"
	],
	"filament_minimal_purge_on_wipe_tower": [
		"15",
		"15"
	],
	"filament_multitool_ramming_volume": [
		"5",
		"5"
	],
	"filament_retract_length_toolchange": [
		"10",
		"10"
	],
	"filament_retraction_length": [
		"3",
		"3"
	],
	"filament_type": [
		"PLA-CF"
	],
	"filament_z_hop": [
		"nil",
		"nil"
	],
	"filament_z_hop_types": [
		"Slope Lift",
		"Slope Lift"
	],
	"nozzle_temperature": [
		"220",
		"210"
	],
	"nozzle_temperature_initial_layer": [
		"220",
		"210"
	],
	"nozzle_temperature_range_high": [
		"250",
		"250"
	],
	"nozzle_temperature_range_low": [
		"210",
		"210"
	],
	"pressure_advance": [
		"0.015",
		"0.03"
	],
	"filament_cost": [
		"35"
	],
	"filament_density": [
		"1.22"
	],
	"slow_down_layer_time": [
		"8"
	],
	"activate_air_filtration": [
		"0",
		"0"
	],
	"chamber_temperatures": [
		"0"
	],
	"complete_print_exhaust_fan_speed": [
		"70",
		"70"
	],
	"cool_plate_temp": [
		"45"
	],
	"cool_plate_temp_initial_layer": [
		"45"
	],
	"during_print_exhaust_fan_speed": [
		"70",
		"70"
	],
	"filament_long_retractions_when_cut": [
		"nil",
		"nil"
	],
	"filament_retraction_distances_when_cut": [
		"nil",
		"nil"
	],
	"filament_retraction_speed": [
		"nil",
		"nil"
	],
	"overhang_fan_threshold": [
		"50%"
	],
	"required_nozzle_HRC": [
		"40"
	],
	"slow_down_min_speed": [
		"20"
	],
	"temperature_vitrification": [
		"45"
	],
	"additional_cooling_fan_speed": [
		"0",
		"0"
	],
	"filament_extruder_variant": [
		"Direct Drive Standard",
		"Direct Drive High Flow"
	],
	"fan_min_speed": [
		"100",
		"100"
	],
	"fan_max_speed": [
		"100",
		"100"
	]
}