{
	"type": "filament",
	"name": "Prusament rPLA @CORE One",
	"renamed_from": "Prusament rPLA CORE One;Prusament rPLA @CORE One MMU3;Prusament rPLA CORE One MMU3",
	"inherits": "fdm_filament_pla",
	"from": "system",
	"setting_id": "Bw6H4vFnq7YExyLd",
	"filament_id": "OFWRITFw",
	"instantiation": "true",
	"include": [
		"fdm_filament_template_nextruder_pla"
	],
	"chamber_temperature": [
		"20"
	],
	"close_fan_the_first_x_layers": [
		"1"
	],
	"compatible_printers": [
		"Prusa CORE One 0.25 nozzle",
		"Prusa CORE One 0.3 nozzle",
		"Prusa CORE One 0.4 nozzle",
		"Prusa CORE One 0.5 nozzle",
		"Prusa CORE One HF 0.4 nozzle",
		"Prusa CORE One HF 0.5 nozzle",
		"Prusa CORE One MMU3 0.4 nozzle",
		"Prusa CORE One MMU3 0.25 nozzle",
		"Prusa CORE One MMU3 0.3 nozzle"
	],
	"fan_cooling_layer_time": [
		"40"
	],
	"fan_max_speed": [
		"100"
	],
	"fan_min_speed": [
		"85"
	],
	"filament_cost": [
		"37.49"
	],
	"filament_density": [
		"1.24"
	],
	"filament_diameter": [
		"1.75"
	],
	"filament_end_gcode": [
		"; Filament-specific end gcode"
	],
	"filament_flow_ratio": [
		"1"
	],
	"filament_max_volumetric_speed": [
		"10"
	],
	"filament_minimal_purge_on_wipe_tower": [
		"15"
	],
	"filament_notes": [
		""
	],
	"filament_soluble": [
		"0"
	],
	"filament_start_gcode": [
		"M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.07{elsif nozzle_diameter[filament_extruder_id]==0.35}0.06{elsif nozzle_diameter[filament_extruder_id]==0.6}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
	],
	"filament_type": [
		"PLA"
	],
	"filament_vendor": [
		"Prusa Polymers"
	],
	"filament_z_hop": [
		"0.6"
	],
	"filament_z_hop_types": [
		"Slope Lift"
	],
	"full_fan_speed_layer": [
		"3"
	],
	"hot_plate_temp": [
		"60"
	],
	"hot_plate_temp_initial_layer": [
		"60"
	],
	"idle_temperature": [
		"170"
	],
	"nozzle_temperature": [
		"205"
	],
	"nozzle_temperature_initial_layer": [
		"205"
	],
	"overhang_fan_speed": [
		"100"
	],
	"reduce_fan_stop_start_freq": [
		"1"
	],
	"slow_down_layer_time": [
		"8"
	],
	"slow_down_min_speed": [
		"20"
	]
}