{
	"type": "filament",
	"name": "INSLOGIC PLA Pro @BBL P2S",
	"inherits": "INSLOGIC PLA Pro @base",
	"from": "system",
	"setting_id": "UAd1QXW7vm9gwoEc",
	"instantiation": "true",
	"filament_flow_ratio": [
		"0.98",
		"0.98"
	],
	"filament_max_volumetric_speed": [
		"12",
		"12"
	],
	"filament_scarf_seam_type": [
		"all"
	],
	"filament_scarf_height": [
		"10%"
	],
	"filament_scarf_gap": [
		"0%"
	],
	"filament_scarf_length": [
		"10"
	],
	"filament_change_length": [
		"5"
	],
	"filament_prime_volume": [
		"30"
	],
	"filament_start_gcode": [
		"; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
	],
	"eng_plate_temp": [
		"55"
	],
	"eng_plate_temp_initial_layer": [
		"55"
	],
	"filament_deretraction_speed": [
		"nil",
		"nil"
	],
	"filament_flush_temp": [
		"0",
		"0"
	],
	"filament_flush_volumetric_speed": [
		"0",
		"0"
	],
	"filament_long_retractions_when_cut": [
		"nil",
		"nil"
	],
	"filament_ramming_volumetric_speed": [
		"-1",
		"-1"
	],
	"filament_ramming_volumetric_speed_nc": [
		"-1",
		"-1"
	],
	"filament_retract_before_wipe": [
		"nil",
		"nil"
	],
	"filament_retract_restart_extra": [
		"nil",
		"nil"
	],
	"filament_retract_when_changing_layer": [
		"nil",
		"nil"
	],
	"filament_retraction_distances_when_cut": [
		"10",
		"10"
	],
	"filament_retraction_length": [
		"1",
		"1"
	],
	"filament_retraction_minimum_travel": [
		"nil",
		"nil"
	],
	"filament_retraction_speed": [
		"nil",
		"nil"
	],
	"filament_wipe": [
		"nil",
		"nil"
	],
	"filament_wipe_distance": [
		"nil",
		"nil"
	],
	"filament_z_hop": [
		"nil",
		"nil"
	],
	"filament_z_hop_types": [
		"nil",
		"nil"
	],
	"filament_extruder_variant": [
		"Direct Drive Standard",
		"Direct Drive High Flow"
	],
	"first_x_layer_fan_speed": [
		"40"
	],
	"filament_pre_cooling_temperature": [
		"0",
		"0"
	],
	"filament_pre_cooling_temperature_nc": [
		"0",
		"0"
	],
	"filament_ramming_travel_time": [
		"0",
		"0"
	],
	"filament_ramming_travel_time_nc": [
		"0",
		"0"
	],
	"filament_adaptive_volumetric_speed": [
		"0",
		"0"
	],
	"long_retractions_when_ec": [
		"0",
		"0"
	],
	"nozzle_temperature": [
		"215",
		"215"
	],
	"nozzle_temperature_initial_layer": [
		"215",
		"215"
	],
	"retraction_distances_when_ec": [
		"0",
		"0"
	],
	"volumetric_speed_coefficients": [
		"0 0 0 0 0 0",
		"0 0 0 0 0 0"
	],
	"nozzle_temperature_range_low": [
		"205",
		"205"
	],
	"nozzle_temperature_range_high": [
		"245",
		"245"
	],
	"hot_plate_temp": [
		"55"
	],
	"hot_plate_temp_initial_layer": [
		"55"
	],
	"textured_plate_temp": [
		"55"
	],
	"textured_plate_temp_initial_layer": [
		"55"
	],
	"fan_min_speed": [
		"60",
		"60"
	],
	"fan_max_speed": [
		"100",
		"100"
	],
	"additional_cooling_fan_speed": [
		"70",
		"70"
	],
	"compatible_printers": [
		"Bambu Lab P2S 0.4 nozzle"
	]
}