{
	"type": "machine",
	"from": "system",
	"instantiation": "true",
	"inherits": "fdm_creality_common",
	"printer_model": "Creality K1_CFS-C",
	"auxiliary_fan": "1",
	"bbl_use_printhost": "0",
	"bed_exclude_area": "0x0",
	"bed_mesh_max": "99999,99999",
	"bed_mesh_min": "-99999,-99999",
	"bed_mesh_probe_distance": "50,50",
	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
	"best_object_pos": "0.5,0.5",
	"change_filament_gcode": "G2 Z{z_after_toolchange + 0.4} I0.86 J0.86 P1 F10000 ; spiral lift a little from second lift\nG1 X0 Y245 F30000\nG1 Z{z_after_toolchange} F600",
	"cooling_tube_length": "0",
	"cooling_tube_retraction": "0",
	"creality_flush_time": "119",
	"default_print_profile": "0.20mm Standard @Creality K1_CFS-C 0.4 nozzle",
	"disable_m73": "0",
	"emit_machine_limits_to_gcode": "1",
	"enable_filament_ramming": "0",
	"extra_loading_move": "0",
	"extruder_clearance_height_to_lid": "101",
	"extruder_clearance_height_to_rod": "45",
	"extruder_clearance_radius": "65",
	"fan_kickstart": "0",
	"fan_speedup_overhangs": "1",
	"fan_speedup_time": "0",
	"gcode_flavor": "klipper",
	"high_current_on_filament_swap": "0",
	"host_type": "octoprint",
	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
	"machine_LED_light_exist": "1",
	"machine_end_gcode": "END_PRINT",
	"machine_load_filament_time": "119",
	"machine_max_acceleration_e": "5000",
	"machine_max_acceleration_extruding": "20000",
	"machine_max_acceleration_retracting": "5000",
	"machine_max_acceleration_travel": "20000",
	"machine_max_acceleration_x": "20000",
	"machine_max_acceleration_y": "20000",
	"machine_max_acceleration_z": "300",
	"machine_max_jerk_e": "10",
	"machine_max_jerk_x": "20",
	"machine_max_jerk_y": "20",
	"machine_max_jerk_z": "5",
	"machine_max_speed_e": "100",
	"machine_max_speed_x": "800",
	"machine_max_speed_y": "800",
	"machine_max_speed_z": "20",
	"machine_min_extruding_rate": "0,0",
	"machine_min_travel_rate": "0,0",
	"machine_pause_gcode": "PAUSE",
	"machine_platform_motion_enable": "1",
	"machine_ptc_exist": "1",
	"machine_start_gcode": "START_PRINT EXTRUDER_TEMP=[nozzle_temperature_initial_layer] BED_TEMP=[bed_temperature_initial_layer_single]\nT[initial_no_support_extruder]\nM204 S2000\nM104 S[nozzle_temperature_initial_layer]\nG1 Z3 F600\nM83\nG92 E0\nG1 Z1 F600",
	"machine_unload_filament_time": "0",
	"manual_filament_change": "0",
	"nozzle_hrc": "0",
	"nozzle_type": "brass",
	"nozzle_volume": "200",
	"parking_pos_retraction": "0",
	"preferred_orientation": "0",
	"prime_tower_position_type": "Middle Upper",
	"printable_area": "0x0,220x0,220x220,0x220",
	"printable_height": "250",
	"printer_technology": "FFF",
	"printer_variant": "0.4",
	"printhost_authorization_type": "key",
	"printhost_ssl_ignore_revoke": "0",
	"purge_in_prime_tower": "1",
	"scan_first_layer": "0",
	"silent_mode": "0",
	"single_extruder_multi_material": "1",
	"support_air_filtration": "1",
	"support_chamber_temp_control": "0",
	"support_multi_bed_types": "1",
	"thumbnails": "96x96,300x300",
	"thumbnails_format": "PNG",
	"time_cost": "0",
	"use_firmware_retraction": "0",
	"use_relative_e_distances": "1",
	"z_offset": "0",
	"default_filament_profile": [
		"Creality Generic PLA @K1-all"
	],
	"deretraction_speed": "40",
	"extruder_colour": "#FCE94F",
	"extruder_offset": "0x0",
	"max_layer_height": "0.3",
	"min_layer_height": "0.08",
	"nozzle_diameter": [
		"0.4"
	],
	"retract_before_wipe": "70%",
	"retract_length_toolchange": "0",
	"retract_lift_above": "0",
	"retract_lift_below": "249",
	"retract_lift_enforce": "All Surfaces",
	"retract_restart_extra": "0",
	"retract_restart_extra_toolchange": "0",
	"retract_when_changing_layer": "1",
	"retraction_length": "0.8",
	"retraction_minimum_travel": "1",
	"retraction_speed": "40",
	"wipe": "1",
	"wipe_distance": "2",
	"z_hop": "0.4",
	"z_hop_types": "Auto Lift",
	"name": "Creality K1_CFS-C 0.4 nozzle",
	"setting_id": "AnvSIapWvZ2Jpc3T"
}