Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) (#13379 )

* Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) New infill geometry derived from FillGyroid. Two parameters are auto-computed per-region from density, line spacing, and layer height (no user inputs): omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing) clamped to [0.5, 2.0] -- Euler-Bernoulli buckling: critical load ~ 1/L^2, so shorter wavelength under higher load (denser infill) raises buckling resistance. amplitude = 0.55 / omega^2, clamped to [0.20, 0.65] -- Curved-beam bending stress: peak stress ~ A * omega^2, so amplitude is reduced as omega rises to keep peak fiber stress bounded while preserving stiffness. Files: - src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new) - src/libslic3r/Fill/FillBase.cpp (factory case) - src/libslic3r/Fill/Fill.cpp (switch case) - src/libslic3r/Layer.cpp (switch case) - src/libslic3r/PrintConfig.{hpp,cpp} (enum + label) - src/libslic3r/CMakeLists.txt (build sources) User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown. Density still chosen by user; omega/amplitude are internal. * Fix build: layer_height is in FillParams, not Fill base * Add ipOptimizedGyroid to multiline infill list in ConfigManipulation * Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean Per @RF47's review feedback, fold the optimized wave math into FillGyroid itself behind a per-region boolean instead of a separate infill enum. What changes: - New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default false). When unchecked, gyroid behavior is byte-identical to before. - Optimized wave math (compute_omega_factor, compute_amplitude_factor, f_opt, make_*_opt, make_optimized_gyroid_waves) lives inside FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized. - FillParams gains a bool gyroid_optimized field, populated in Fill.cpp from region_config alongside fill_multiline. - UI checkbox added under Strength > Infill in Tab.cpp, label "Optimize gyroid wave (experimental)". Toggle is hidden by ConfigManipulation when sparse_infill_pattern != ipGyroid. - "gyroid_optimized" added to s_Preset_print_options for preset I/O. What goes away: - ipOptimizedGyroid enum value, factory case, switch cases, dropdown label, string key. - FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into FillGyroid.cpp). - Net diff drops by ~250 lines. Existing profiles using gyroid are unaffected. * Wire gyroid_optimized through SurfaceFillParams to FillParams Linux build failed because line 921 in Fill.cpp populates a SurfaceFillParams (the dedup struct), not FillParams directly. Add the field there, in operator< / operator==, and copy it to FillParams at both conversion sites. * Use toggle_line for gyroid_optimized: hide row when pattern != gyroid * Account for multiline wall thickness in omega correction (per @RF47) When fill_multiline = N, each gyroid wall is N lines thick, so the geometric scale fed into the buckling correction term should be spacing * N rather than spacing. Increases omega (tighter wavelength) when multiline is enabled, consistent with the thicker wall being more buckling-resistant. * Optimized gyroid via marching squares on the implicit scalar field Per @RF47 review: replace the analytical f_opt / make_one_period_opt wave generator (which had visible kinks at vertical-horizontal transitions) with a marching-squares iso-extraction on the gyroid scalar field, modeled on FillTpmsFK.cpp. - New marchsq::GyroidField in FillGyroid.cpp evaluates F(x,y,z) = sin(fx*x)cos(fy*y) + sin(fy*y)cos(fz*z) + sin(fz*z)cos(fx*x) where fx = omega * baseline (anisotropic in x), fy = fz = baseline. - get_gyroid_polylines() runs marching squares at iso=0 and converts rings to polylines. - _fill_surface_single() optimized branch now builds GyroidField, runs marching squares, and skips the bb.min translate (field output is already in absolute coords). - Dropped: f_opt, make_one_period_opt, make_wave_opt, make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude has no clean analog in iso-zero extraction. - Standard (non-optimized) gyroid path unchanged. * Mass calibration: compensate period by cbrt(omega) for x-anisotropic field Per @RF47: optimized vs standard gyroid had different masses at the same sparse_infill_density setting. Cause: scaling fx by omega while leaving fy=fz at the baseline raised the surface-area-to-volume ratio by approximately omega^(1/3) (the geometric mean of the three frequencies). Fix: multiply the base period by cbrt(omega) so the geometric mean of (fx, fy, fz) returns to the standard baseline. Net effect: fx = omega^(2/3) * baseline_orig fy = fz = omega^(-1/3) * baseline_orig which preserves total mass at the same density setting while preserving the load-direction anisotropy this PR introduces. * Switch optimized gyroid anisotropy from X to Z (per @RF47) Z is the typical compression-load axis for FFF parts and is not at delamination risk under compression — so the dominant failure mode is column buckling of the vertical strands themselves. Tightening fz directly shortens the effective vertical strand length, which improves Z-axis buckling resistance. Mass calibration via cbrt(omega) period compensation still applies (scaling exactly one of three frequencies by omega; the geometric- mean preservation argument is symmetric across axes). * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> * Address review feedback (Copilot + @RF47) - Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid) so non-gyroid surfaces don't differ in SurfaceFillParams by an irrelevant flag (would unnecessarily split fill batching). [Copilot suggestion, RF47 confirmed correct] - PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength is parameterized (the marching-squares iso=0 extraction is invariant to a uniform field scale, so amplitude has no effect). - FillBase.hpp: shorten gyroid_optimized comment to match the actual carried state (no amplitude term). - FillGyroid.cpp: shorten the marchsq namespace comment block; the ODR concern was overstated (FillTpmsFK uses the same pattern fine). * Drop redundant marchsq bb expansion (Copilot) bb is already offset by 10 * scale_(spacing) above for edge-artifact margin; the second offset on bb_field doubled the raster area for no geometric benefit and hurt CPU time on large parts. * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Ian Bassi <ian.bassi@outlook.com> * Fix density mismatch + rename to Z-buckling bias optimization Issue (per @ianalexis): at the same sparse_infill_density setting, the optimized branch produced denser fill than standard. Verified via Python sim (sim_gyroid_compare.py) using marching squares on the implicit field across multiple z slices. Root cause: the omega formula was inverted from the buckling-physics intent. The naive sqrt(density_adj) factor produced omega < 1 at typical print densities (10-30%), which LENGTHENED the Z wavelength instead of shortening it -- net loss in both mass and strength. Fix: - compute_omega_factor: invert to sqrt(1 / density_adj), clamp to [1.0, 2.0]. Now omega = 2.0 at low density (long strands need most help) and clamps to 1.0 above ~30% density (no-op, since standard gyroid is already short enough). - Remove the cbrt(omega) period compensation. Empirically (sim table embedded in FillGyroid.cpp comment) the inverted formula keeps line length per area at ~1.000 of standard across all densities with no period scaling needed. Predicted gains (sim, Z-axis Euler buckling proxy): density line/std strength/std 10% 1.000 2.84x 15% 1.000 1.89x 20% 1.000 1.42x 30%+ 1.000 1.00x (no-op) Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op above 30% density and Z-only). Renamed user-facing label to "Z-buckling bias optimization (experimental)" with updated tooltip that scopes to vertical compression and discloses the density cutoff. Internal config key (gyroid_optimized) unchanged for diff size. Real-world Instron compression tests at Brown's Prince Lab to follow. --------- Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> Co-authored-by: Ian Bassi <ian.bassi@outlook.com> Co-authored-by: SoftFever <softfeverever@gmail.com>
Modifications to the hotbed temperature of various types of printing plates (#13717 )
2026-05-20 20:03:47 +00:00 · 2026-05-20 23:42:32 +08:00 · 2026-05-20 22:55:58 +08:00 · 2026-05-20 19:25:51 +08:00 · 2026-05-20 19:21:02 +08:00 · 2026-05-20 19:20:09 +08:00
513 changed files with 8725 additions and 3994 deletions
--- a/.idea/.gitignore
+++ b/.idea/.gitignore
@@ -1,8 +0,0 @@
-# Default ignored files
-/shelf/
-/workspace.xml
-# Editor-based HTTP Client requests
-/httpRequests/
-# Datasource local storage ignored files
-/dataSources/
-/dataSources.local.xml
--- a/.idea/OrcaSlicer.iml
+++ b/.idea/OrcaSlicer.iml
@@ -1,2 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<module classpath="CMake" type="CPP_MODULE" version="4" />
--- a/.idea/codeStyles/Project.xml
+++ b/.idea/codeStyles/Project.xml
@@ -1,7 +0,0 @@
-<component name="ProjectCodeStyleConfiguration">
-  <code_scheme name="Project" version="173">
-    <clangFormatSettings>
-      <option name="ENABLED" value="true" />
-    </clangFormatSettings>
-  </code_scheme>
-</component>
--- a/.idea/codeStyles/codeStyleConfig.xml
+++ b/.idea/codeStyles/codeStyleConfig.xml
@@ -1,5 +0,0 @@
-<component name="ProjectCodeStyleConfiguration">
-  <state>
-    <option name="USE_PER_PROJECT_SETTINGS" value="true" />
-  </state>
-</component>
--- a/.idea/misc.xml
+++ b/.idea/misc.xml
@@ -1,4 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<project version="4">
-  <component name="CMakeWorkspace" PROJECT_DIR="$PROJECT_DIR$" />
-</project>
--- a/.idea/modules.xml
+++ b/.idea/modules.xml
@@ -1,8 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<project version="4">
-  <component name="ProjectModuleManager">
-    <modules>
-      <module fileurl="file://$PROJECT_DIR$/.idea/OrcaSlicer.iml" filepath="$PROJECT_DIR$/.idea/OrcaSlicer.iml" />
-    </modules>
-  </component>
-</project>
--- a/.idea/vcs.xml
+++ b/.idea/vcs.xml
@@ -1,6 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<project version="4">
-  <component name="VcsDirectoryMappings">
-    <mapping directory="" vcs="Git" />
-  </component>
-</project>
--- a/localization/i18n/it/OrcaSlicer_it.po
+++ b/localization/i18n/it/OrcaSlicer_it.po
--- a/resources/data/hints.ini
+++ b/resources/data/hints.ini
@@ -94,8 +94,8 @@ text = Switch workspaces\nYou can switch between <b>Prepare</b> and <b>Preview</
 [hint:How to use keyboard shortcuts]
 text = How to use keyboard shortcuts\nDid you know that Orca Slicer offers a wide range of keyboard shortcuts and 3D scene operations?

-[hint:Reverse on odd]
-text = Reverse on odd\nDid you know that <b>Reverse on odd</b> feature can significantly improve the surface quality of your overhangs?
+[hint:Reverse on even]
+text = Reverse on even\nDid you know that <b>Reverse on even</b> feature can significantly improve the surface quality of your overhangs? However, it can cause wall inconsistencies so use carefully!

 [hint:Cut Tool]
 text = Cut Tool\nDid you know that you can cut a model at any angle and position with the cutting tool?
--- a/resources/images/filter.svg
+++ b/resources/images/filter.svg
@@ -0,0 +1 @@
+<?xml version="1.0" encoding="UTF-8"?><svg id="a" xmlns="http://www.w3.org/2000/svg" width="16" height="16" viewBox="0 0 16 16"><polygon points=".5 .5 5.5 7.5 5.5 13.5 9.5 15.5 9.5 7.5 14.5 .5 .5 .5" style="fill:none; stroke:#949494; stroke-linecap:round; stroke-linejoin:round;"/><line x1="8.64" y1="4.5" x2="10.19" y2="2.34" style="fill:none; stroke:#949494; stroke-linecap:round; stroke-linejoin:round;"/></svg>
--- a/resources/profiles/Afinia/filament/fdm_filament_common.json
+++ b/resources/profiles/Afinia/filament/fdm_filament_common.json
@@ -61,7 +61,7 @@
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Anet
+++ b/resources/profiles/Anet
--- a/resources/profiles/Anet/Anet
+++ b/resources/profiles/Anet/Anet
--- a/resources/profiles/Anet/machine/Anet
+++ b/resources/profiles/Anet/machine/Anet
@@ -1,237 +0,0 @@
-{
-	"type": "machine",
-	"name": "Anet A8 Plus 0.4 nozzle",
-	"inherits": "",
-	"from": "User",
-	"adaptive_bed_mesh_margin": "0",
-	"auxiliary_fan": "0",
-	"bbl_use_printhost": "0",
-	"bed_custom_model": "",
-	"bed_custom_texture": "",
-	"bed_exclude_area": [
-		"0x0"
-	],
-	"bed_mesh_max": "99999,99999",
-	"bed_mesh_min": "-99999,-99999",
-	"bed_mesh_probe_distance": "50,50",
-	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
-	"best_object_pos": "0.5,0.5",
-	"change_extrusion_role_gcode": "",
-	"change_filament_gcode": "M600",
-	"cooling_tube_length": "5",
-	"cooling_tube_retraction": "91.5",
-	"default_bed_type": "",
-	"default_filament_profile": [
-		"Anycubic Generic PLA"
-	],
-	"default_print_profile": "0.20mm Standard @Anycubic 4MaxPro2",
-	"deretraction_speed": [
-		"25"
-	],
-	"disable_m73": "0",
-	"emit_machine_limits_to_gcode": "1",
-	"enable_filament_ramming": "1",
-	"enable_long_retraction_when_cut": "0",
-	"extra_loading_move": "-2",
-	"extruder_clearance_height_to_lid": "140",
-	"extruder_clearance_height_to_rod": "36",
-	"extruder_clearance_radius": "65",
-	"extruder_colour": [
-		"#018001"
-	],
-	"extruder_offset": [
-		"0x0"
-	],
-	"fan_kickstart": "0",
-	"fan_speedup_overhangs": "1",
-	"fan_speedup_time": "0",
-	"gcode_flavor": "marlin",
-	"head_wrap_detect_zone": [],
-	"high_current_on_filament_swap": "0",
-	"host_type": "octoprint",
-	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
-	"long_retractions_when_cut": [
-		"0"
-	],
-	"machine_end_gcode": "M104 S0 ; turn off extruder heating\nM140 S0 ; turn off bed heating\nM107 ; turn off fans\nG91 ; relative positioning\nG0 Z+0.5 ; move Z up a tiny bit\nG90 ; absolute positioning\nG0 X135 Y105 F{machine_max_speed_x[0]*60} ; move extruder to center position\nG0 Z190.5 F{machine_max_speed_z[0]*60} ; lower the plattform to Z min\nM84 ; steppers off\nG90 ; absolute positioning\n",
-	"machine_load_filament_time": "0",
-	"machine_max_acceleration_e": [
-		"5000",
-		"5000"
-	],
-	"machine_max_acceleration_extruding": [
-		"1250",
-		"1250"
-	],
-	"machine_max_acceleration_retracting": [
-		"1250",
-		"1250"
-	],
-	"machine_max_acceleration_travel": [
-		"1500",
-		"1500"
-	],
-	"machine_max_acceleration_x": [
-		"1000",
-		"900"
-	],
-	"machine_max_acceleration_y": [
-		"1000",
-		"900"
-	],
-	"machine_max_acceleration_z": [
-		"1000",
-		"100"
-	],
-	"machine_max_jerk_e": [
-		"5",
-		"5"
-	],
-	"machine_max_jerk_x": [
-		"6",
-		"6"
-	],
-	"machine_max_jerk_y": [
-		"6",
-		"6"
-	],
-	"machine_max_jerk_z": [
-		"0.2",
-		"0.2"
-	],
-	"machine_max_junction_deviation": [
-		"0.10",
-		"0"
-	],
-	"machine_max_speed_e": [
-		"120",
-		"120"
-	],
-	"machine_max_speed_x": [
-		"200",
-		"200"
-	],
-	"machine_max_speed_y": [
-		"200",
-		"200"
-	],
-	"machine_max_speed_z": [
-		"64",
-		"16"
-	],
-	"machine_min_extruding_rate": [
-		"0",
-		"0"
-	],
-	"machine_min_travel_rate": [
-		"0",
-		"0"
-	],
-	"machine_pause_gcode": "M601",
-	"machine_start_gcode": "G21 ; metric values\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 X0 Y0 ; home X and Y\nG28 Z0 ; home Z\nG1 Z30 F{machine_max_speed_z[0]*60} ; move Z a bit down to not blow on the bed edge while heating\nG1 X10 F3900 ; let some space on x to prevent the filament cooling exhaust from beeing blocked by the servo motor\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM106 S80 ; turn on fan to prevent air nozzle melt while heating up\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM107 ; start with the fan off\nG28 X0 ; goto X home again\nG92 E0 ; zero the extruded length\nG1 Z0.2 F360 ; move plattform upwards\n; extrude material next to the plattform (comment or remove following lines to disable)\nG1 F180 E20 ; extrude some material next to the plattform\nG92 E0 ; zero the extruded length\nG1 E-[retraction_length] F{retraction_speed[0]*60} ; do a filament retract\nG92 E0 ; zero the extruded length again\nG1 X5 F3900 ; move sideways to get rid of that string\nG1 E[retraction_length] F{retraction_speed[0]*60} ; do a filament deretract with retract parameters\nG92 E0 ; zero the extruded length again\n; draw intro line (comment or remove following lines to disable)\nG1 X30 E5 F700 ; draw intro line\nG92 E0 ; zero the extruded length\nG1 E-[retraction_length] F{retraction_speed[0]*60} ; do a filament retract\nG1 X40 Z2.0 ; move away from the introline\nG92 E0 ; zero the extruded length again\nG1 E[retraction_length] F{retraction_speed[0]*60} ; do a filament deretract with retract parameters\n; end of intro line code\nM117 Printing...\nG5",
-	"machine_tool_change_time": "0",
-	"machine_unload_filament_time": "0",
-	"manual_filament_change": "0",
-	"max_layer_height": [
-		"0.3"
-	],
-	"max_resonance_avoidance_speed": "120",
-	"min_layer_height": [
-		"0.07"
-	],
-	"min_resonance_avoidance_speed": "70",
-	"nozzle_diameter": [
-		"0.4"
-	],
-	"nozzle_height": "2.5",
-	"nozzle_hrc": "0",
-	"nozzle_type": "undefine",
-	"nozzle_volume": "0",
-	"parking_pos_retraction": "92",
-	"pellet_modded_printer": "0",
-	"preferred_orientation": "0",
-	"printable_area": [
-		"0x0",
-		"300x0",
-		"300x300",
-		"0x300"
-	],
-	"printable_height": "350",
-	"printer_model": "Anet A8 Plus",
-	"printer_notes": "",
-	"printer_settings_id": "Anet A8 Plus 0.4 nozzle",
-	"printer_structure": "undefine",
-	"printer_technology": "FFF",
-	"printer_variant": "0.4",
-	"printhost_authorization_type": "key",
-	"printhost_ssl_ignore_revoke": "0",
-	"printing_by_object_gcode": "",
-	"purge_in_prime_tower": "1",
-	"resonance_avoidance": "0",
-	"retract_before_wipe": [
-		"0%"
-	],
-	"retract_length_toolchange": [
-		"10"
-	],
-	"retract_lift_above": [
-		"0"
-	],
-	"retract_lift_below": [
-		"0"
-	],
-	"retract_lift_enforce": [
-		"All Surfaces"
-	],
-	"retract_restart_extra": [
-		"0"
-	],
-	"retract_restart_extra_toolchange": [
-		"0"
-	],
-	"retract_when_changing_layer": [
-		"1"
-	],
-	"retraction_distances_when_cut": [
-		"18"
-	],
-	"retraction_length": [
-		"2.5"
-	],
-	"retraction_minimum_travel": [
-		"2"
-	],
-	"retraction_speed": [
-		"35"
-	],
-	"scan_first_layer": "0",
-	"silent_mode": "0",
-	"single_extruder_multi_material": "1",
-	"support_air_filtration": "1",
-	"support_chamber_temp_control": "1",
-	"support_multi_bed_types": "0",
-	"template_custom_gcode": "",
-	"thumbnails": "48x48/PNG,300x300/PNG",
-	"thumbnails_format": "PNG",
-	"time_cost": "0",
-	"time_lapse_gcode": "",
-	"travel_slope": [
-		"3"
-	],
-	"upward_compatible_machine": [],
-	"use_firmware_retraction": "0",
-	"use_relative_e_distances": "1",
-	"wipe": [
-		"1"
-	],
-	"wipe_distance": [
-		"1"
-	],
-	"z_hop": [
-		"0.4"
-	],
-	"z_hop_types": [
-		"Normal Lift"
-	],
-	"z_offset": "0"
-}
--- a/resources/profiles/Anet/machine/Anet
+++ b/resources/profiles/Anet/machine/Anet
--- a/resources/profiles/Anycubic/filament/fdm_filament_common.json
+++ b/resources/profiles/Anycubic/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Anycubic/machine/Anycubic
+++ b/resources/profiles/Anycubic/machine/Anycubic
--- a/resources/profiles/Artillery/filament/fdm_filament_common.json
+++ b/resources/profiles/Artillery/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/BBL/filament/fdm_filament_common.json
+++ b/resources/profiles/BBL/filament/fdm_filament_common.json
@@ -97,7 +97,7 @@
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_ramming_volumetric_speed": [
 		"-1"
--- a/resources/profiles/Blocks/filament/fdm_filament_common.json
+++ b/resources/profiles/Blocks/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/CONSTRUCT3D/filament/fdm_filament_common.json
+++ b/resources/profiles/CONSTRUCT3D/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/CoLiDo/filament/fdm_filament_common.json
+++ b/resources/profiles/CoLiDo/filament/fdm_filament_common.json
@@ -67,7 +67,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Comgrow/filament/fdm_filament_common.json
+++ b/resources/profiles/Comgrow/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Creality/filament/fdm_filament_common.json
+++ b/resources/profiles/Creality/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Cubicon/filament/fdm_filament_common.json
+++ b/resources/profiles/Cubicon/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/DeltaMaker/filament/fdm_filament_pet.json
+++ b/resources/profiles/DeltaMaker/filament/fdm_filament_pet.json
@@ -14,7 +14,7 @@
 		"15"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"8"
 	],
 	"filament_type": [
 		"PETG"
--- a/resources/profiles/DeltaMaker/filament/fdm_filament_pla.json
+++ b/resources/profiles/DeltaMaker/filament/fdm_filament_pla.json
@@ -6,7 +6,7 @@
 	"instantiation": "false",
 	"fan_cooling_layer_time": "100",
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_type": [
 		"PLA"
--- a/resources/profiles/DeltaMaker/filament/fdm_filament_tpu.json
+++ b/resources/profiles/DeltaMaker/filament/fdm_filament_tpu.json
@@ -14,7 +14,7 @@
 		"30"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"3.6"
 	],
 	"filament_type": [
 		"TPU"
--- a/resources/profiles/Dremel/filament/fdm_filament_common.json
+++ b/resources/profiles/Dremel/filament/fdm_filament_common.json
@@ -40,7 +40,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Elegoo/filament/fdm_filament_common.json
+++ b/resources/profiles/Elegoo/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Eryone/filament/fdm_filament_common.json
+++ b/resources/profiles/Eryone/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/FLSun/filament/fdm_filament_common.json
+++ b/resources/profiles/FLSun/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Flashforge/filament/fdm_filament_common.json
+++ b/resources/profiles/Flashforge/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Flashforge/filament/fdm_filament_pet.json
+++ b/resources/profiles/Flashforge/filament/fdm_filament_pet.json
@@ -38,7 +38,7 @@
 		"15"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"8"
 	],
 	"filament_type": [
 		"PETG"
--- a/resources/profiles/Flashforge/filament/fdm_filament_pla.json
+++ b/resources/profiles/Flashforge/filament/fdm_filament_pla.json
@@ -8,7 +8,7 @@
 		"100"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_type": [
 		"PLA"
--- a/resources/profiles/FlyingBear/filament/Ghost7/fdm_filament_common_Ghost7.json
+++ b/resources/profiles/FlyingBear/filament/Ghost7/fdm_filament_common_Ghost7.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/FlyingBear/filament/S1/fdm_filament_common_S1.json
+++ b/resources/profiles/FlyingBear/filament/S1/fdm_filament_common_S1.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/FlyingBear/filament/fdm_filament_common.json
+++ b/resources/profiles/FlyingBear/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/InfiMech/filament/EX+APS/fdm_filament_common_EX+APS.json
+++ b/resources/profiles/InfiMech/filament/EX+APS/fdm_filament_common_EX+APS.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/InfiMech/filament/EX/fdm_filament_common_EX.json
+++ b/resources/profiles/InfiMech/filament/EX/fdm_filament_common_EX.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/InfiMech/filament/HSN/fdm_filament_common_HSN.json
+++ b/resources/profiles/InfiMech/filament/HSN/fdm_filament_common_HSN.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/InfiMech/filament/fdm_filament_common.json
+++ b/resources/profiles/InfiMech/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/LH/filament/fdm_filament_common.json
+++ b/resources/profiles/LH/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/LONGER/filament/fdm_filament_common.json
+++ b/resources/profiles/LONGER/filament/fdm_filament_common.json
@@ -64,7 +64,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/OrcaArena/filament/fdm_filament_common.json
+++ b/resources/profiles/OrcaArena/filament/fdm_filament_common.json
@@ -70,7 +70,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_common.json
+++ b/resources/profiles/OrcaFilamentLibrary/filament/base/fdm_filament_common.json
@@ -61,7 +61,7 @@
 		"nil"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Peopoly/filament/fdm_filament_common.json
+++ b/resources/profiles/Peopoly/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Phrozen/filament/fdm_filament_common.json
+++ b/resources/profiles/Phrozen/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Prusa/filament/fdm_filament_common.json
+++ b/resources/profiles/Prusa/filament/fdm_filament_common.json
@@ -58,7 +58,7 @@
 		"1.75"
 	],
 	"filament_max_volumetric_speed": [
-		"0"
+		"12"
 	],
 	"filament_minimal_purge_on_wipe_tower": [
 		"15"
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -30,9 +30,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -48,12 +48,6 @@
 	"pressure_advance": [
 		"0.04"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"80"
-	],
 	"filament_density": [
 		"1.24"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -30,9 +30,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -48,12 +48,6 @@
 	"pressure_advance": [
 		"0.04"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"80"
-	],
 	"filament_density": [
 		"1.24"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
Peyton Marcotte	956fcea7e2	Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) (#13379 ) * Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) New infill geometry derived from FillGyroid. Two parameters are auto-computed per-region from density, line spacing, and layer height (no user inputs): omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing) clamped to [0.5, 2.0] -- Euler-Bernoulli buckling: critical load ~ 1/L^2, so shorter wavelength under higher load (denser infill) raises buckling resistance. amplitude = 0.55 / omega^2, clamped to [0.20, 0.65] -- Curved-beam bending stress: peak stress ~ A * omega^2, so amplitude is reduced as omega rises to keep peak fiber stress bounded while preserving stiffness. Files: - src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new) - src/libslic3r/Fill/FillBase.cpp (factory case) - src/libslic3r/Fill/Fill.cpp (switch case) - src/libslic3r/Layer.cpp (switch case) - src/libslic3r/PrintConfig.{hpp,cpp} (enum + label) - src/libslic3r/CMakeLists.txt (build sources) User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown. Density still chosen by user; omega/amplitude are internal. * Fix build: layer_height is in FillParams, not Fill base * Add ipOptimizedGyroid to multiline infill list in ConfigManipulation * Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean Per @RF47's review feedback, fold the optimized wave math into FillGyroid itself behind a per-region boolean instead of a separate infill enum. What changes: - New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default false). When unchecked, gyroid behavior is byte-identical to before. - Optimized wave math (compute_omega_factor, compute_amplitude_factor, f_opt, make__opt, make_optimized_gyroid_waves) lives inside FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized. - FillParams gains a bool gyroid_optimized field, populated in Fill.cpp from region_config alongside fill_multiline. - UI checkbox added under Strength > Infill in Tab.cpp, label "Optimize gyroid wave (experimental)". Toggle is hidden by ConfigManipulation when sparse_infill_pattern != ipGyroid. - "gyroid_optimized" added to s_Preset_print_options for preset I/O. What goes away: - ipOptimizedGyroid enum value, factory case, switch cases, dropdown label, string key. - FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into FillGyroid.cpp). - Net diff drops by ~250 lines. Existing profiles using gyroid are unaffected. Wire gyroid_optimized through SurfaceFillParams to FillParams Linux build failed because line 921 in Fill.cpp populates a SurfaceFillParams (the dedup struct), not FillParams directly. Add the field there, in operator< / operator==, and copy it to FillParams at both conversion sites. * Use toggle_line for gyroid_optimized: hide row when pattern != gyroid * Account for multiline wall thickness in omega correction (per @RF47) When fill_multiline = N, each gyroid wall is N lines thick, so the geometric scale fed into the buckling correction term should be spacing * N rather than spacing. Increases omega (tighter wavelength) when multiline is enabled, consistent with the thicker wall being more buckling-resistant. * Optimized gyroid via marching squares on the implicit scalar field Per @RF47 review: replace the analytical f_opt / make_one_period_opt wave generator (which had visible kinks at vertical-horizontal transitions) with a marching-squares iso-extraction on the gyroid scalar field, modeled on FillTpmsFK.cpp. - New marchsq::GyroidField in FillGyroid.cpp evaluates F(x,y,z) = sin(fxx)cos(fyy) + sin(fyy)cos(fzz) + sin(fzz)cos(fxx) where fx = omega * baseline (anisotropic in x), fy = fz = baseline. - get_gyroid_polylines() runs marching squares at iso=0 and converts rings to polylines. - _fill_surface_single() optimized branch now builds GyroidField, runs marching squares, and skips the bb.min translate (field output is already in absolute coords). - Dropped: f_opt, make_one_period_opt, make_wave_opt, make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude has no clean analog in iso-zero extraction. - Standard (non-optimized) gyroid path unchanged. * Mass calibration: compensate period by cbrt(omega) for x-anisotropic field Per @RF47: optimized vs standard gyroid had different masses at the same sparse_infill_density setting. Cause: scaling fx by omega while leaving fy=fz at the baseline raised the surface-area-to-volume ratio by approximately omega^(1/3) (the geometric mean of the three frequencies). Fix: multiply the base period by cbrt(omega) so the geometric mean of (fx, fy, fz) returns to the standard baseline. Net effect: fx = omega^(2/3) * baseline_orig fy = fz = omega^(-1/3) * baseline_orig which preserves total mass at the same density setting while preserving the load-direction anisotropy this PR introduces. * Switch optimized gyroid anisotropy from X to Z (per @RF47) Z is the typical compression-load axis for FFF parts and is not at delamination risk under compression — so the dominant failure mode is column buckling of the vertical strands themselves. Tightening fz directly shortens the effective vertical strand length, which improves Z-axis buckling resistance. Mass calibration via cbrt(omega) period compensation still applies (scaling exactly one of three frequencies by omega; the geometric- mean preservation argument is symmetric across axes). * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> * Address review feedback (Copilot + @RF47) - Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid) so non-gyroid surfaces don't differ in SurfaceFillParams by an irrelevant flag (would unnecessarily split fill batching). [Copilot suggestion, RF47 confirmed correct] - PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength is parameterized (the marching-squares iso=0 extraction is invariant to a uniform field scale, so amplitude has no effect). - FillBase.hpp: shorten gyroid_optimized comment to match the actual carried state (no amplitude term). - FillGyroid.cpp: shorten the marchsq namespace comment block; the ODR concern was overstated (FillTpmsFK uses the same pattern fine). * Drop redundant marchsq bb expansion (Copilot) bb is already offset by 10 * scale_(spacing) above for edge-artifact margin; the second offset on bb_field doubled the raster area for no geometric benefit and hurt CPU time on large parts. * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Ian Bassi <ian.bassi@outlook.com> * Fix density mismatch + rename to Z-buckling bias optimization Issue (per @ianalexis): at the same sparse_infill_density setting, the optimized branch produced denser fill than standard. Verified via Python sim (sim_gyroid_compare.py) using marching squares on the implicit field across multiple z slices. Root cause: the omega formula was inverted from the buckling-physics intent. The naive sqrt(density_adj) factor produced omega < 1 at typical print densities (10-30%), which LENGTHENED the Z wavelength instead of shortening it -- net loss in both mass and strength. Fix: - compute_omega_factor: invert to sqrt(1 / density_adj), clamp to [1.0, 2.0]. Now omega = 2.0 at low density (long strands need most help) and clamps to 1.0 above ~30% density (no-op, since standard gyroid is already short enough). - Remove the cbrt(omega) period compensation. Empirically (sim table embedded in FillGyroid.cpp comment) the inverted formula keeps line length per area at ~1.000 of standard across all densities with no period scaling needed. Predicted gains (sim, Z-axis Euler buckling proxy): density line/std strength/std 10% 1.000 2.84x 15% 1.000 1.89x 20% 1.000 1.42x 30%+ 1.000 1.00x (no-op) Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op above 30% density and Z-only). Renamed user-facing label to "Z-buckling bias optimization (experimental)" with updated tooltip that scopes to vertical compression and discloses the density cutoff. Internal config key (gyroid_optimized) unchanged for diff size. Real-world Instron compression tests at Brown's Prince Lab to follow. --------- Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> Co-authored-by: Ian Bassi <ian.bassi@outlook.com> Co-authored-by: SoftFever <softfeverever@gmail.com>	2026-05-20 23:42:32 +08:00
HYzd766	b882da99ad	Modifications to the hotbed temperature of various types of printing plates (#13717 )	2026-05-20 22:55:58 +08:00
ExPikaPaka	19eb9e634f	Adds force sync UI button. Added missing code for previous PR (#13757 )	2026-05-20 19:25:51 +08:00
Ian Chua	62d4344e59	feat: Updated UI for better distinction of orca cloud and bambu cloud (#13755 ) * feat: Updated UI for better distinction of orca cloud and bambu cloud * refined UI	2026-05-20 19:21:02 +08:00
Ian Chua	4542a15009	fix: use bambu's network plugin (#13756 )	2026-05-20 19:20:09 +08:00
raistlin7447	b7f872541d	Fix input_filename_base using object name instead of project name (#13753 )	2026-05-20 12:32:53 +08:00
ExPikaPaka	1aedf8f22c	Added UI force-sync button and fixed bug that didn't sync in one case… (#13745 ) * Added UI force-sync button and fixed bug that didn't sync in one case and caused orange highlight * Fix sync preset race: join old thread before starting new one --------- Co-authored-by: Mykola Nahirnyi <mnahirnyi@amcbridge.com> Co-authored-by: SoftFever <softfeverever@gmail.com>	2026-05-20 12:18:08 +08:00
SoftFever	d2c24fdabb	Fix Linux/Wayland crash on Preview tab at startup (#13747 )	2026-05-20 01:54:17 +08:00
Kappa971	5a77daf75c	Fix Italian translation (#13720 )	2026-05-20 00:46:22 +08:00
Ioannis Giannakas	75039f8bec	Fix first layer toolhead preaheating bug with 2+ extuders and ooze prevention enabled (#13741 )	2026-05-20 00:23:04 +08:00
Ian Chua	ebf9d9fd42	feat: add UI feedback on http error and some logs (#13738 ) * feat: add UI feedback on http error and some logs * spelling fix * show error dialog only once per session * show errors with plater notification when on developer mode * remove return * remove irrelevant logs	2026-05-19 23:15:44 +08:00
Ian Bassi	ff68a2859d	Ignore Jerk values Warning if using JD (#13575 ) * Ignore Jerk values if using JD * add flavor check	2026-05-19 09:42:44 -03:00
SoftFever	46e47cec0a	Fix ObjectTable crash on cell deselect after wxWidgets 3.3.2 upgrade (#13740 ) GridCellSupportEditor::DoActivate dereferenced grid->GetSelectedBlocks().begin() without checking against end(). In wxWidgets 3.1.5 that range always contained at least one block; in 3.3.2 it is empty after the user deselects, and the dereference crashes inside wxGridBlockCoords::GetLeftCol(). Fall back to the (row, col) that triggered activation when the selection is empty, so the existing single-cell branch handles it. While here, drop a dead local_table cast that was never read.	2026-05-19 18:14:33 +08:00
Ioannis Giannakas	f4a9830752	Fix reverse on even hint (#13739 )	2026-05-19 10:50:26 +01:00
Brandon Wees	1f2ed70288	fix: macOS deep links after wxWidgets 3.3.2 upgrade (#13737 ) Fix macOS orcaslicer:// deep links after wxWidgets 3.3.2 upgrade Install an OrcaSlicer-owned kAEGetURL Apple Event handler from on_init_inner(). The wxWidgets 3.3.2 handler registered in applicationWillFinishLaunching: stopped delivering URL events to GUI_App::MacOpenURL on macOS (#13119), so links from Printables / Thingiverse opened a blank project instead of importing the model. Registering our own handler late in startup is last-writer-wins on NSAppleEventManager and routes back to the existing MacOpenURL -> start_download path, restoring the pre-upgrade behavior without touching wxWidgets. Co-authored-by: Claude Opus 4.7 <noreply@anthropic.com>	2026-05-19 17:13:07 +08:00
Ioannis Giannakas	3370e224b2	Cooling: add per-printer non-zero fan PWM floor and fix N=0 fan ramp override (#13715 ) * Cooling: add per-printer non-zero fan PWM floor and fix N=0 ramp override * updated parameter naming	2026-05-19 09:40:53 +01:00
SoftFever	7fc1e109c5	delete misshaped profiles	2026-05-19 14:35:20 +08:00
SoftFever	374e4ad8a9	Follow up update for PR #13724 : improve GC and shorten comments	2026-05-19 14:32:18 +08:00
SoftFever	d0fbda3af1	Fix Linux segfault when loading Fluidd/Mainsail printer hosts (#7210 ) (#13724 ) * Fix Linux segfault when loading Fluidd/Mainsail printer hosts (#7210) Co-authored-by: VittC <58783944+VittC@users.noreply.github.com> * narrow down the changes --------- Co-authored-by: VittC <58783944+VittC@users.noreply.github.com>	2026-05-19 14:26:34 +08:00
Andrew	f78836bef4	Stop tracking .idea files (#13735 )	2026-05-19 11:20:04 +08:00
SoftFever	d8369e5f75	Fix faint toolbar icons on Wayland (#13723 ) Use glBlendFuncSeparate in GLTexture::render_sub_texture so destination alpha stays at 1.0. The Wayland compositor honors framebuffer alpha for window compositing; the previous straight-alpha blend reduced dst alpha at anti-aliased icon edges, making them semi-transparent against the desktop. RGB blending is unchanged, so X11/Windows/macOS are unaffected.	2026-05-19 01:38:37 +08:00
SoftFever	88b4a63228	Fix Linux data-view dropdown popup parenting (#13721 ) Delay opening the object-list filament dropdown on wxGTK until the editor window is mapped, avoiding popup creation without a valid native toplevel. Also set the GTK transient parent for dropdown popups created from data-view cell editors.	2026-05-19 01:01:53 +08:00
yw4z	dc12126b78	Fix 2 Linux assertation errors on gtk_window_resize() (#13718 ) Update DropDown.cpp	2026-05-18 19:01:42 +03:00
yw4z	054a173af7	Fix possible crash on startup because of low max volumetric speed on profiles (#13716 ) * Update fdm_filament_common.json * update * Update fdm_filament_common.json	2026-05-18 19:00:48 +03:00
Kappa971	248a55abd0	Update Italian translation (#13674 )	2026-05-18 10:29:38 -03:00
yw4z	b4aa070c40	MultiChooseDialog & CheckList class & improvements for Profile Dependencies (#9971 ) * init * fix * fix * update * update * update * Update Tab.cpp * Update CheckList.cpp	2026-05-18 19:46:47 +08:00
Thomas Henauer	b9ff15054f	Fix wxGTK submenu popup parenting and sizing on Wayland (#13707 )	2026-05-18 18:01:19 +08:00
CSLRDoesntGameDev	ddeaa4ba82	Add patches to the Anycubic Kobra X machine json (#13677 ) add patched anycubic kobra x machine json Co-authored-by: SoftFever <softfeverever@gmail.com>	2026-05-18 16:57:24 +08:00
Ian Chua	b333b04815	log: add logs surrounding logout to potentially catch any unwanted logouts or errors (#13713 ) # Description Currently, there is some suspicious behavior going on with the logout flow, adding some logs to potentially catch any unwanted logouts or unintentional behaviors. [How to Download Pull Requests Artifacts for Testing](https://www.orcaslicer.com/wiki/how_to_download_pr_artifacts)	2026-05-18 16:39:59 +08:00
Ioannis Giannakas	e5ca01ba9e	Fix per-volume "Only one wall" overrides being ignored on assembly parts (#13714 )	2026-05-18 09:24:28 +01:00
				`@@ -0,0 +1 @@`
				`<?xml version="1.0" encoding="UTF-8"?><svg id="a" xmlns="http://www.w3.org/2000/svg" width="16" height="16" viewBox="0 0 16 16"><polygon points=".5 .5 5.5 7.5 5.5 13.5 9.5 15.5 9.5 7.5 14.5 .5 .5 .5" style="fill:none; stroke:#949494; stroke-linecap:round; stroke-linejoin:round;"/><line x1="8.64" y1="4.5" x2="10.19" y2="2.34" style="fill:none; stroke:#949494; stroke-linecap:round; stroke-linejoin:round;"/></svg>`