Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) (#13379 )

* Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) New infill geometry derived from FillGyroid. Two parameters are auto-computed per-region from density, line spacing, and layer height (no user inputs): omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing) clamped to [0.5, 2.0] -- Euler-Bernoulli buckling: critical load ~ 1/L^2, so shorter wavelength under higher load (denser infill) raises buckling resistance. amplitude = 0.55 / omega^2, clamped to [0.20, 0.65] -- Curved-beam bending stress: peak stress ~ A * omega^2, so amplitude is reduced as omega rises to keep peak fiber stress bounded while preserving stiffness. Files: - src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new) - src/libslic3r/Fill/FillBase.cpp (factory case) - src/libslic3r/Fill/Fill.cpp (switch case) - src/libslic3r/Layer.cpp (switch case) - src/libslic3r/PrintConfig.{hpp,cpp} (enum + label) - src/libslic3r/CMakeLists.txt (build sources) User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown. Density still chosen by user; omega/amplitude are internal. * Fix build: layer_height is in FillParams, not Fill base * Add ipOptimizedGyroid to multiline infill list in ConfigManipulation * Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean Per @RF47's review feedback, fold the optimized wave math into FillGyroid itself behind a per-region boolean instead of a separate infill enum. What changes: - New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default false). When unchecked, gyroid behavior is byte-identical to before. - Optimized wave math (compute_omega_factor, compute_amplitude_factor, f_opt, make_*_opt, make_optimized_gyroid_waves) lives inside FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized. - FillParams gains a bool gyroid_optimized field, populated in Fill.cpp from region_config alongside fill_multiline. - UI checkbox added under Strength > Infill in Tab.cpp, label "Optimize gyroid wave (experimental)". Toggle is hidden by ConfigManipulation when sparse_infill_pattern != ipGyroid. - "gyroid_optimized" added to s_Preset_print_options for preset I/O. What goes away: - ipOptimizedGyroid enum value, factory case, switch cases, dropdown label, string key. - FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into FillGyroid.cpp). - Net diff drops by ~250 lines. Existing profiles using gyroid are unaffected. * Wire gyroid_optimized through SurfaceFillParams to FillParams Linux build failed because line 921 in Fill.cpp populates a SurfaceFillParams (the dedup struct), not FillParams directly. Add the field there, in operator< / operator==, and copy it to FillParams at both conversion sites. * Use toggle_line for gyroid_optimized: hide row when pattern != gyroid * Account for multiline wall thickness in omega correction (per @RF47) When fill_multiline = N, each gyroid wall is N lines thick, so the geometric scale fed into the buckling correction term should be spacing * N rather than spacing. Increases omega (tighter wavelength) when multiline is enabled, consistent with the thicker wall being more buckling-resistant. * Optimized gyroid via marching squares on the implicit scalar field Per @RF47 review: replace the analytical f_opt / make_one_period_opt wave generator (which had visible kinks at vertical-horizontal transitions) with a marching-squares iso-extraction on the gyroid scalar field, modeled on FillTpmsFK.cpp. - New marchsq::GyroidField in FillGyroid.cpp evaluates F(x,y,z) = sin(fx*x)cos(fy*y) + sin(fy*y)cos(fz*z) + sin(fz*z)cos(fx*x) where fx = omega * baseline (anisotropic in x), fy = fz = baseline. - get_gyroid_polylines() runs marching squares at iso=0 and converts rings to polylines. - _fill_surface_single() optimized branch now builds GyroidField, runs marching squares, and skips the bb.min translate (field output is already in absolute coords). - Dropped: f_opt, make_one_period_opt, make_wave_opt, make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude has no clean analog in iso-zero extraction. - Standard (non-optimized) gyroid path unchanged. * Mass calibration: compensate period by cbrt(omega) for x-anisotropic field Per @RF47: optimized vs standard gyroid had different masses at the same sparse_infill_density setting. Cause: scaling fx by omega while leaving fy=fz at the baseline raised the surface-area-to-volume ratio by approximately omega^(1/3) (the geometric mean of the three frequencies). Fix: multiply the base period by cbrt(omega) so the geometric mean of (fx, fy, fz) returns to the standard baseline. Net effect: fx = omega^(2/3) * baseline_orig fy = fz = omega^(-1/3) * baseline_orig which preserves total mass at the same density setting while preserving the load-direction anisotropy this PR introduces. * Switch optimized gyroid anisotropy from X to Z (per @RF47) Z is the typical compression-load axis for FFF parts and is not at delamination risk under compression — so the dominant failure mode is column buckling of the vertical strands themselves. Tightening fz directly shortens the effective vertical strand length, which improves Z-axis buckling resistance. Mass calibration via cbrt(omega) period compensation still applies (scaling exactly one of three frequencies by omega; the geometric- mean preservation argument is symmetric across axes). * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> * Address review feedback (Copilot + @RF47) - Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid) so non-gyroid surfaces don't differ in SurfaceFillParams by an irrelevant flag (would unnecessarily split fill batching). [Copilot suggestion, RF47 confirmed correct] - PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength is parameterized (the marching-squares iso=0 extraction is invariant to a uniform field scale, so amplitude has no effect). - FillBase.hpp: shorten gyroid_optimized comment to match the actual carried state (no amplitude term). - FillGyroid.cpp: shorten the marchsq namespace comment block; the ODR concern was overstated (FillTpmsFK uses the same pattern fine). * Drop redundant marchsq bb expansion (Copilot) bb is already offset by 10 * scale_(spacing) above for edge-artifact margin; the second offset on bb_field doubled the raster area for no geometric benefit and hurt CPU time on large parts. * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Ian Bassi <ian.bassi@outlook.com> * Fix density mismatch + rename to Z-buckling bias optimization Issue (per @ianalexis): at the same sparse_infill_density setting, the optimized branch produced denser fill than standard. Verified via Python sim (sim_gyroid_compare.py) using marching squares on the implicit field across multiple z slices. Root cause: the omega formula was inverted from the buckling-physics intent. The naive sqrt(density_adj) factor produced omega < 1 at typical print densities (10-30%), which LENGTHENED the Z wavelength instead of shortening it -- net loss in both mass and strength. Fix: - compute_omega_factor: invert to sqrt(1 / density_adj), clamp to [1.0, 2.0]. Now omega = 2.0 at low density (long strands need most help) and clamps to 1.0 above ~30% density (no-op, since standard gyroid is already short enough). - Remove the cbrt(omega) period compensation. Empirically (sim table embedded in FillGyroid.cpp comment) the inverted formula keeps line length per area at ~1.000 of standard across all densities with no period scaling needed. Predicted gains (sim, Z-axis Euler buckling proxy): density line/std strength/std 10% 1.000 2.84x 15% 1.000 1.89x 20% 1.000 1.42x 30%+ 1.000 1.00x (no-op) Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op above 30% density and Z-only). Renamed user-facing label to "Z-buckling bias optimization (experimental)" with updated tooltip that scopes to vertical compression and discloses the density cutoff. Internal config key (gyroid_optimized) unchanged for diff size. Real-world Instron compression tests at Brown's Prince Lab to follow. --------- Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> Co-authored-by: Ian Bassi <ian.bassi@outlook.com> Co-authored-by: SoftFever <softfeverever@gmail.com>
Modifications to the hotbed temperature of various types of printing plates (#13717 )
2026-05-20 20:03:47 +00:00 · 2026-05-20 23:42:32 +08:00 · 2026-05-20 22:55:58 +08:00 · 2026-05-20 19:25:51 +08:00 · 2026-05-20 19:21:02 +08:00 · 2026-05-20 19:20:09 +08:00
438 changed files with 7481 additions and 3350 deletions
--- a/localization/i18n/it/OrcaSlicer_it.po
+++ b/localization/i18n/it/OrcaSlicer_it.po
@@ -17664,9 +17664,10 @@ msgid ""
 "Apply scarf joints only to smooth perimeters where traditional seams do not "
 "conceal the seams at sharp corners effectively."
 msgstr ""
-"Applica le cuciture a sciarpa solo sui perimetri lisci, dove le cuciture "
-"tradizionali non riescono a nascondere efficacemente quelle in "
-"corrispondenza degli angoli vivi."
+"Applica le cuciture a sciarpa solo sui perimetri lisci e curvi, dove le "
+"cuciture tradizionali risulterebbero molto evidenti. Gli angoli netti "
+"continueranno a utilizzare le cuciture normali per mantenere la precisione "
+"dimensionale."

 msgid "Conditional angle threshold"
 msgstr "Soglia angolo condizionale"
@@ -17734,45 +17735,48 @@ msgstr ""
 "cucitura a sciarpa."

 msgid "Scarf start height"
-msgstr "Altezza iniziale sciarpa"
+msgstr "Altezza iniziale cucitura a sciarpa"

 msgid ""
 "Start height of the scarf.\n"
 "This amount can be specified in millimeters or as a percentage of the "
 "current layer height. The default value for this parameter is 0."
 msgstr ""
-"Altezza iniziale della sciarpa.\n"
-"Questa quantità può essere specificata in millimetri o come percentuale "
+"Altezza iniziale della cucitura a sciarpa.\n"
+"Questo valore può essere specificato in millimetri o come percentuale "
 "dell'altezza dello strato corrente. Il valore predefinito per questo "
 "parametro è 0."

 msgid "Scarf around entire wall"
-msgstr "Sciarpa attorno all'intera parete"
+msgstr "Cucitura a sciarpa su intera parete"

 msgid "The scarf extends to the entire length of the wall."
-msgstr "La sciarpa si estende per tutta la lunghezza della parete."
+msgstr ""
+"La cucitura a sciarpa si estende lungo tutto il perimetro della parete."

 msgid "Scarf length"
-msgstr "Lunghezza sciarpa"
+msgstr "Lunghezza cucitura a sciarpa"

 msgid ""
 "Length of the scarf. Setting this parameter to zero effectively disables the "
 "scarf."
 msgstr ""
-"Lunghezza della sciarpa. Impostando questo parametro su zero, la sciarpa "
-"viene effettivamente disabilitata."
+"Lunghezza della cucitura a sciarpa. Impostando questo parametro su zero, la "
+"cucitura a sciarpa viene disabilitata."

 msgid "Scarf steps"
-msgstr "Incrementi sciarpa"
+msgstr "Incrementi cucitura a sciarpa"

 msgid "Minimum number of segments of each scarf."
-msgstr "Numero minimo di segmenti di ogni sciarpa."
+msgstr ""
+"Numero minimo di segmenti utilizzati per la creazione della sfumatura della "
+"cucitura a sciarpa."

 msgid "Scarf joint for inner walls"
 msgstr "Cucitura a sciarpa per pareti interne"

 msgid "Use scarf joint for inner walls as well."
-msgstr "Utilizzare la cucitura a sciarpa anche per le pareti interne."
+msgstr "Utilizza la cucitura a sciarpa anche per le pareti interne."

 msgid "Role base wipe speed"
 msgstr "Velocità di spurgo basata su ruolo"
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -30,9 +30,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi Q1 Pro 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"Bambu PETG @Qidi X-Plus 4 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -48,12 +48,6 @@
 	"pressure_advance": [
 		"0.04"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"80"
-	],
 	"filament_density": [
 		"1.24"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Bambu
+++ b/resources/profiles/Qidi/filament/Bambu
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -30,9 +30,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"260"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"24.5"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi Q1 Pro 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.2 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.4 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.6 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -18,9 +18,6 @@
 	"filament_settings_id": [
 		"HATCHBOX PETG @Qidi X-Plus 4 0.8 nozzle"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
 	"overhang_fan_speed": [
 		"90"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -48,12 +48,6 @@
 	"pressure_advance": [
 		"0.04"
 	],
-	"hot_plate_temp_initial_layer": [
-		"80"
-	],
-	"hot_plate_temp": [
-		"80"
-	],
 	"filament_density": [
 		"1.24"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/HATCHBOX
+++ b/resources/profiles/Qidi/filament/HATCHBOX
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,9 +27,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -21,9 +21,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -21,9 +21,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -21,9 +21,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Overture
+++ b/resources/profiles/Qidi/filament/Overture
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -24,9 +24,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,9 +27,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -21,9 +21,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"250"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -21,9 +21,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -21,9 +21,6 @@
 	"filament_max_volumetric_speed": [
 		"2"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -18,9 +18,6 @@
 	"fan_max_speed": [
 		"80"
 	],
-	"hot_plate_temp_initial_layer": [
-		"90"
-	],
 	"nozzle_temperature": [
 		"255"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -30,12 +30,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/PolyLite
+++ b/resources/profiles/Qidi/filament/PolyLite
@@ -27,12 +27,6 @@
 	"full_fan_speed_layer": [
 		"3"
 	],
-	"hot_plate_temp": [
-		"60"
-	],
-	"hot_plate_temp_initial_layer": [
-		"60"
-	],
 	"nozzle_temperature": [
 		"210"
 	],
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -72,5 +72,35 @@
 	"hot_plate_temp": [
 		"90"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"80"
+	],
+	"eng_plate_temp": [
+		"90"
+	],
+	"supertack_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"90"
+	],
+	"textured_cool_plate_temp": [
+		"80"
+	],
+	"cool_plate_temp_initial_layer": [
+		"80"
+	],
+	"eng_plate_temp_initial_layer": [
+		"90"
+	],
+	"supertack_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"90"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"80"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -72,5 +72,35 @@
 	"hot_plate_temp": [
 		"90"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"80"
+	],
+	"eng_plate_temp": [
+		"90"
+	],
+	"supertack_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"90"
+	],
+	"textured_cool_plate_temp": [
+		"80"
+	],
+	"cool_plate_temp_initial_layer": [
+		"80"
+	],
+	"eng_plate_temp_initial_layer": [
+		"90"
+	],
+	"supertack_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"90"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"80"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -61,10 +61,10 @@
 		"8"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"70"
+		"60"
 	],
 	"supertack_plate_temp": [
-		"70"
+		"60"
 	],
 	"temperature_vitrification": [
 		"70"
@@ -75,5 +75,29 @@
 	"hot_plate_temp": [
 		"80"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_cool_plate_temp": [
+		"60"
+	],
+	"cool_plate_temp_initial_layer": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"60"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -61,10 +61,10 @@
 		"8"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"70"
+		"60"
 	],
 	"supertack_plate_temp": [
-		"70"
+		"60"
 	],
 	"temperature_vitrification": [
 		"70"
@@ -75,5 +75,29 @@
 	"hot_plate_temp": [
 		"80"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_cool_plate_temp": [
+		"60"
+	],
+	"cool_plate_temp_initial_layer": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"60"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -42,5 +42,35 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Bambu
+++ b/resources/profiles/Qidi/filament/Q2/Bambu
@@ -42,5 +42,35 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -75,5 +75,35 @@
 	"hot_plate_temp": [
 		"90"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"80"
+	],
+	"eng_plate_temp": [
+		"90"
+	],
+	"supertack_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"90"
+	],
+	"textured_cool_plate_temp": [
+		"80"
+	],
+	"cool_plate_temp_initial_layer": [
+		"80"
+	],
+	"eng_plate_temp_initial_layer": [
+		"90"
+	],
+	"supertack_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"90"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"80"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -75,5 +75,35 @@
 	"hot_plate_temp": [
 		"90"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"80"
+	],
+	"eng_plate_temp": [
+		"90"
+	],
+	"supertack_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"90"
+	],
+	"textured_cool_plate_temp": [
+		"80"
+	],
+	"cool_plate_temp_initial_layer": [
+		"80"
+	],
+	"eng_plate_temp_initial_layer": [
+		"90"
+	],
+	"supertack_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"90"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"80"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -64,10 +64,10 @@
 		"12"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"70"
+		"60"
 	],
 	"supertack_plate_temp": [
-		"70"
+		"60"
 	],
 	"temperature_vitrification": [
 		"70"
@@ -78,5 +78,29 @@
 	"hot_plate_temp": [
 		"80"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_cool_plate_temp": [
+		"60"
+	],
+	"cool_plate_temp_initial_layer": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"60"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -64,10 +64,10 @@
 		"12"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"70"
+		"60"
 	],
 	"supertack_plate_temp": [
-		"70"
+		"60"
 	],
 	"temperature_vitrification": [
 		"70"
@@ -78,5 +78,29 @@
 	"hot_plate_temp": [
 		"80"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"60"
+	],
+	"eng_plate_temp": [
+		"80"
+	],
+	"textured_plate_temp": [
+		"80"
+	],
+	"textured_cool_plate_temp": [
+		"60"
+	],
+	"cool_plate_temp_initial_layer": [
+		"60"
+	],
+	"eng_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_plate_temp_initial_layer": [
+		"80"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"60"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -54,5 +54,29 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -54,5 +54,29 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -46,10 +46,10 @@
 		"0.032"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"35"
+		"45"
 	],
 	"supertack_plate_temp": [
-		"35"
+		"45"
 	],
 	"temperature_vitrification": [
 		"45"
@@ -60,5 +60,29 @@
 	"hot_plate_temp": [
 		"55"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"55"
+	],
+	"textured_plate_temp": [
+		"55"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"55"
+	],
+	"textured_plate_temp_initial_layer": [
+		"55"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -46,10 +46,10 @@
 		"0.032"
 	],
 	"supertack_plate_temp_initial_layer": [
-		"35"
+		"45"
 	],
 	"supertack_plate_temp": [
-		"35"
+		"45"
 	],
 	"temperature_vitrification": [
 		"45"
@@ -60,5 +60,29 @@
 	"hot_plate_temp": [
 		"55"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"55"
+	],
+	"textured_plate_temp": [
+		"55"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"55"
+	],
+	"textured_plate_temp_initial_layer": [
+		"55"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -48,5 +48,35 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -48,5 +48,35 @@
 	"temperature_vitrification": [
 		"45"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"45"
+	],
+	"eng_plate_temp": [
+		"60"
+	],
+	"hot_plate_temp": [
+		"60"
+	],
+	"textured_plate_temp": [
+		"60"
+	],
+	"textured_cool_plate_temp": [
+		"45"
+	],
+	"cool_plate_temp_initial_layer": [
+		"45"
+	],
+	"eng_plate_temp_initial_layer": [
+		"60"
+	],
+	"hot_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_plate_temp_initial_layer": [
+		"60"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"45"
+	]
 }
--- a/resources/profiles/Qidi/filament/Q2/Generic
+++ b/resources/profiles/Qidi/filament/Q2/Generic
@@ -48,5 +48,35 @@
 	"hot_plate_temp": [
 		"35"
 	],
-	"compatible_printers": []
+	"compatible_printers": [],
+	"cool_plate_temp": [
+		"30"
+	],
+	"eng_plate_temp": [
+		"35"
+	],
+	"supertack_plate_temp": [
+		"30"
+	],
+	"textured_plate_temp": [
+		"35"
+	],
+	"textured_cool_plate_temp": [
+		"30"
+	],
+	"cool_plate_temp_initial_layer": [
+		"30"
+	],
+	"eng_plate_temp_initial_layer": [
+		"35"
+	],
+	"supertack_plate_temp_initial_layer": [
+		"30"
+	],
+	"textured_plate_temp_initial_layer": [
+		"35"
+	],
+	"textured_cool_plate_temp_initial_layer": [
+		"30"
+	]
 }
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
Peyton Marcotte	956fcea7e2	Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) (#13379 ) * Add Optimized Gyroid infill (auto-tuned wavelength + amplitude) New infill geometry derived from FillGyroid. Two parameters are auto-computed per-region from density, line spacing, and layer height (no user inputs): omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing) clamped to [0.5, 2.0] -- Euler-Bernoulli buckling: critical load ~ 1/L^2, so shorter wavelength under higher load (denser infill) raises buckling resistance. amplitude = 0.55 / omega^2, clamped to [0.20, 0.65] -- Curved-beam bending stress: peak stress ~ A * omega^2, so amplitude is reduced as omega rises to keep peak fiber stress bounded while preserving stiffness. Files: - src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new) - src/libslic3r/Fill/FillBase.cpp (factory case) - src/libslic3r/Fill/Fill.cpp (switch case) - src/libslic3r/Layer.cpp (switch case) - src/libslic3r/PrintConfig.{hpp,cpp} (enum + label) - src/libslic3r/CMakeLists.txt (build sources) User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown. Density still chosen by user; omega/amplitude are internal. * Fix build: layer_height is in FillParams, not Fill base * Add ipOptimizedGyroid to multiline infill list in ConfigManipulation * Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean Per @RF47's review feedback, fold the optimized wave math into FillGyroid itself behind a per-region boolean instead of a separate infill enum. What changes: - New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default false). When unchecked, gyroid behavior is byte-identical to before. - Optimized wave math (compute_omega_factor, compute_amplitude_factor, f_opt, make__opt, make_optimized_gyroid_waves) lives inside FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized. - FillParams gains a bool gyroid_optimized field, populated in Fill.cpp from region_config alongside fill_multiline. - UI checkbox added under Strength > Infill in Tab.cpp, label "Optimize gyroid wave (experimental)". Toggle is hidden by ConfigManipulation when sparse_infill_pattern != ipGyroid. - "gyroid_optimized" added to s_Preset_print_options for preset I/O. What goes away: - ipOptimizedGyroid enum value, factory case, switch cases, dropdown label, string key. - FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into FillGyroid.cpp). - Net diff drops by ~250 lines. Existing profiles using gyroid are unaffected. Wire gyroid_optimized through SurfaceFillParams to FillParams Linux build failed because line 921 in Fill.cpp populates a SurfaceFillParams (the dedup struct), not FillParams directly. Add the field there, in operator< / operator==, and copy it to FillParams at both conversion sites. * Use toggle_line for gyroid_optimized: hide row when pattern != gyroid * Account for multiline wall thickness in omega correction (per @RF47) When fill_multiline = N, each gyroid wall is N lines thick, so the geometric scale fed into the buckling correction term should be spacing * N rather than spacing. Increases omega (tighter wavelength) when multiline is enabled, consistent with the thicker wall being more buckling-resistant. * Optimized gyroid via marching squares on the implicit scalar field Per @RF47 review: replace the analytical f_opt / make_one_period_opt wave generator (which had visible kinks at vertical-horizontal transitions) with a marching-squares iso-extraction on the gyroid scalar field, modeled on FillTpmsFK.cpp. - New marchsq::GyroidField in FillGyroid.cpp evaluates F(x,y,z) = sin(fxx)cos(fyy) + sin(fyy)cos(fzz) + sin(fzz)cos(fxx) where fx = omega * baseline (anisotropic in x), fy = fz = baseline. - get_gyroid_polylines() runs marching squares at iso=0 and converts rings to polylines. - _fill_surface_single() optimized branch now builds GyroidField, runs marching squares, and skips the bb.min translate (field output is already in absolute coords). - Dropped: f_opt, make_one_period_opt, make_wave_opt, make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude has no clean analog in iso-zero extraction. - Standard (non-optimized) gyroid path unchanged. * Mass calibration: compensate period by cbrt(omega) for x-anisotropic field Per @RF47: optimized vs standard gyroid had different masses at the same sparse_infill_density setting. Cause: scaling fx by omega while leaving fy=fz at the baseline raised the surface-area-to-volume ratio by approximately omega^(1/3) (the geometric mean of the three frequencies). Fix: multiply the base period by cbrt(omega) so the geometric mean of (fx, fy, fz) returns to the standard baseline. Net effect: fx = omega^(2/3) * baseline_orig fy = fz = omega^(-1/3) * baseline_orig which preserves total mass at the same density setting while preserving the load-direction anisotropy this PR introduces. * Switch optimized gyroid anisotropy from X to Z (per @RF47) Z is the typical compression-load axis for FFF parts and is not at delamination risk under compression — so the dominant failure mode is column buckling of the vertical strands themselves. Tightening fz directly shortens the effective vertical strand length, which improves Z-axis buckling resistance. Mass calibration via cbrt(omega) period compensation still applies (scaling exactly one of three frequencies by omega; the geometric- mean preservation argument is symmetric across axes). * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> * Address review feedback (Copilot + @RF47) - Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid) so non-gyroid surfaces don't differ in SurfaceFillParams by an irrelevant flag (would unnecessarily split fill batching). [Copilot suggestion, RF47 confirmed correct] - PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength is parameterized (the marching-squares iso=0 extraction is invariant to a uniform field scale, so amplitude has no effect). - FillBase.hpp: shorten gyroid_optimized comment to match the actual carried state (no amplitude term). - FillGyroid.cpp: shorten the marchsq namespace comment block; the ODR concern was overstated (FillTpmsFK uses the same pattern fine). * Drop redundant marchsq bb expansion (Copilot) bb is already offset by 10 * scale_(spacing) above for edge-artifact margin; the second offset on bb_field doubled the raster area for no geometric benefit and hurt CPU time on large parts. * Update src/slic3r/GUI/Tab.cpp Co-authored-by: Ian Bassi <ian.bassi@outlook.com> * Fix density mismatch + rename to Z-buckling bias optimization Issue (per @ianalexis): at the same sparse_infill_density setting, the optimized branch produced denser fill than standard. Verified via Python sim (sim_gyroid_compare.py) using marching squares on the implicit field across multiple z slices. Root cause: the omega formula was inverted from the buckling-physics intent. The naive sqrt(density_adj) factor produced omega < 1 at typical print densities (10-30%), which LENGTHENED the Z wavelength instead of shortening it -- net loss in both mass and strength. Fix: - compute_omega_factor: invert to sqrt(1 / density_adj), clamp to [1.0, 2.0]. Now omega = 2.0 at low density (long strands need most help) and clamps to 1.0 above ~30% density (no-op, since standard gyroid is already short enough). - Remove the cbrt(omega) period compensation. Empirically (sim table embedded in FillGyroid.cpp comment) the inverted formula keeps line length per area at ~1.000 of standard across all densities with no period scaling needed. Predicted gains (sim, Z-axis Euler buckling proxy): density line/std strength/std 10% 1.000 2.84x 15% 1.000 1.89x 20% 1.000 1.42x 30%+ 1.000 1.00x (no-op) Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op above 30% density and Z-only). Renamed user-facing label to "Z-buckling bias optimization (experimental)" with updated tooltip that scopes to vertical compression and discloses the density cutoff. Internal config key (gyroid_optimized) unchanged for diff size. Real-world Instron compression tests at Brown's Prince Lab to follow. --------- Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com> Co-authored-by: Ian Bassi <ian.bassi@outlook.com> Co-authored-by: SoftFever <softfeverever@gmail.com>	2026-05-20 23:42:32 +08:00
HYzd766	b882da99ad	Modifications to the hotbed temperature of various types of printing plates (#13717 )	2026-05-20 22:55:58 +08:00
ExPikaPaka	19eb9e634f	Adds force sync UI button. Added missing code for previous PR (#13757 )	2026-05-20 19:25:51 +08:00
Ian Chua	62d4344e59	feat: Updated UI for better distinction of orca cloud and bambu cloud (#13755 ) * feat: Updated UI for better distinction of orca cloud and bambu cloud * refined UI	2026-05-20 19:21:02 +08:00
Ian Chua	4542a15009	fix: use bambu's network plugin (#13756 )	2026-05-20 19:20:09 +08:00
raistlin7447	b7f872541d	Fix input_filename_base using object name instead of project name (#13753 )	2026-05-20 12:32:53 +08:00
ExPikaPaka	1aedf8f22c	Added UI force-sync button and fixed bug that didn't sync in one case… (#13745 ) * Added UI force-sync button and fixed bug that didn't sync in one case and caused orange highlight * Fix sync preset race: join old thread before starting new one --------- Co-authored-by: Mykola Nahirnyi <mnahirnyi@amcbridge.com> Co-authored-by: SoftFever <softfeverever@gmail.com>	2026-05-20 12:18:08 +08:00
SoftFever	d2c24fdabb	Fix Linux/Wayland crash on Preview tab at startup (#13747 )	2026-05-20 01:54:17 +08:00
Kappa971	5a77daf75c	Fix Italian translation (#13720 )	2026-05-20 00:46:22 +08:00
Ioannis Giannakas	75039f8bec	Fix first layer toolhead preaheating bug with 2+ extuders and ooze prevention enabled (#13741 )	2026-05-20 00:23:04 +08:00
Ian Chua	ebf9d9fd42	feat: add UI feedback on http error and some logs (#13738 ) * feat: add UI feedback on http error and some logs * spelling fix * show error dialog only once per session * show errors with plater notification when on developer mode * remove return * remove irrelevant logs	2026-05-19 23:15:44 +08:00