Follow-up to the rack-aware pre-print checks: after the blocking checks
pass, warn (without disabling Send) when the plate needs more matching
hotends than the rack printer currently holds - suggesting rack setup,
a nozzle info refresh, or a re-slice to avoid filament waste - or when
the only matches rely on unreliable nozzle information.
Text-only warning rows; this message board has no refresh or
don't-show-again buttons.
A print sliced for a nozzle that sits in the hotend rack (but is not
mounted) was blocked by the send dialog's mounted-nozzle diameter check,
even though the printer fetches the required nozzle itself (#14685).
Consolidate the three mounted-nozzle gates (_is_nozzle_data_valid,
is_nozzle_type_match, _is_same_nozzle_diameters) into a single
CheckErrorExtruderNozzleWithSlicing fed by s_get_slicing_extuder_nozzles,
which collects the plate's per-extruder nozzle requirements (hybrid
extruders contribute one entry per used sub-nozzle flow). The rack
extruder validates against its whole inventory (mounted + rack) with
guidance to calibrate the rack, refresh nozzle info, or re-slice, and
blocks when toolhead + rack are full (no free slot to stow a nozzle).
Other extruders keep the validity/flow/diameter checks against the
mounted nozzle.
Also add CheckErrorRackStatus, which holds Send while the printer is
still reading the rack hotend information, and judge material hardness
for the rack extruder per dispatch-mapped nozzle as a non-blocking
caution (mounted nozzles keep the blocking gate).
The Filament Track Switch (H2-series accessory, product code O2L-FTS) feeds
every AMS to both extruders through a two-track switch. Port full support
across the device layer, project config, and GUI.
Device / config:
- Model the switch-aware AMS binding (the set of extruders an AMS can feed
and which input track A/B feeds it), switch readiness, the O2L-FTS firmware
module, and the fun2 capability bit for checking a slice against installed
hardware.
- Register has_filament_switcher and enable_filament_dynamic_map as project
config that persists with the project and restores from a saved 3mf, and
force both back to false on every project/printer/CLI load path. Live
device sync is the only thing that sets them true.
GUI:
- Sidebar sync activates the switch from live device state, attributes each
AMS to the extruder its input track feeds, shows a floating status icon
(ready / not-calibrated), and surfaces a one-time tip / not-calibrated
warning.
- Send dialog gains a non-blocking slice-vs-hardware mismatch warning and a
blocking error when a slice needs dynamic nozzle mapping but the switch is
missing or not set up.
- AMS load/unload guards, AMS-view routing glyph + un-calibrated banner +
hidden external-spool road, and mapping-popup external-spool lockout.
- Filament pickers collapse the per-extruder split into a single deduplicated
"AMS filaments" group with a smart-assign toggle when the switch is ready.
- Firmware-upgrade panel lists the O2L-FTS accessory and its version.
- Device-provided filament-change steps (ams.cfs) drive the change-step
display when firmware sends them, including the three switch steps.
- "Load current filament" asks which extruder to feed via a
FeedDirectionDialog when the switch is calibrated.
Inert without the accessory: every path is gated on the switch being
installed (MQTT aux bit 29, default off) or ready, both project flags default
false, and the per-extruder AMS attribution is byte-identical, so AMS state,
the send/load UI, and sliced g-code are unchanged for every printer that does
not report a Filament Track Switch.
Multi-nozzle sync widget, AMS rack-nozzle mapping popup, calibration rework, send-dialog nozzle mapping and extruder-count UI. Includes the fix to persist the AMS sync badge on filament cards (H2C/A2L and direct-sync printers).
Port from BambuStudio commit c8f70c6ca. Shows a warning when AMS
is actively drying during print job preparation, alerting users that
the drying temperature will be lowered during printing.
Syncing the filament list from AMS with the "Overwriting" option
displayed the AMS filaments in the wrong (reversed) order in the
preview, even though the filament mapping that was actually applied
was correct. Reported on macOS with a Bambu X1C.
The preview depends on MaterialHash being iterated in material-index
order. MaterialHash is a WX_DECLARE_HASH_MAP, which under OrcaSlicer's
current wxWidgets 3.3 build (wxUSE_STD_CONTAINERS=1) resolves to
std::unordered_map; its iteration order is unspecified and on macOS
(libc++) comes out reversed, which scrambled the preview. The same
code is unaffected in BambuStudio because its older wxWidgets build
still uses wx's own key-ordered hash table, so this only became
visible after the wx upgrade.
Fixes#14335
* Clean up code
* Filament mapping select ext slot automatically when no AMS filament inserted (OrcaSlicer/OrcaSlicer#13103)
* Show warning if external filament type does not match the one in sliced file
