Code review items (raistlin7447):
1. PrintObject::slice() zeroes m_belt_min_z, m_belt_global_z_offset and
m_belt_global_xy_correction before slicing. They were only written in belt
mode, so a project switched to a normal printer, or whose tilt axis was set
to None, kept the old offsets and shifted the adaptive infill octree and the
organic support layers by them.
2. TreeModelVolumes shifts the support blockers into the raft-offset index
space; a test now pins the index the blocker lands on.
3. The final-alignment clamp in libnest2d is opt-in (NfpPConfig::clamp_to_bin)
and arrange sets it for belt printers only. Printers with an off-centre
best_object_pos keep their alignment; a flat-bed test pins that.
4. The preview's belt view follows the loaded G-code, not the selected printer:
GCodeProcessor carries the file's belt keys (and, for a belt file, its bed)
into export_config_for_render(), and GCodeViewer enables the belt view from
the header tilt.
5. belt_shift_layer_grid() also shifts the cached belt floor and the global Z
offset, so a support-only or brim-only change after the purge-prism snap
matches a fresh slice.
6. update_print_fff_config() resets raft_layers and draft_shield on a belt
printer instead of only greying out the fields Print::validate() rejects.
7. GCodeWriter takes a first-layer point test instead of the FirstLayerPlane;
GCode installs one that measures from the belt surface, like its
extrusions, so the first-layer travel speed and the second-layer
temperature change no longer depend on the gcode_remap_* convention.
8. belt_brim_clip_leading_edge() is exported and called by both the generator
and the test.
9. Both phong.vs shaders use slope.up_direction for the overhang highlight.
The pre-slice and G-code axis remaps are gated on belt_printer through
BeltTransformPipeline::axis_remap_enabled(), so belt keys left in a profile
cannot change a non-belt print.
Tests requested in the review: belt-only keys at non-default values leave
non-belt G-code unchanged; switching a sliced project from belt to non-belt
(and tilt axis None) matches a fresh slice; a support-only change on a belt
purge print matches a fresh slice; non-belt start G-code moves keep the
first-layer Z in the processor; the belt brim's segment count catches a band
emitted twice.
The belt-to-non-belt test exposed an unrelated gap: invalidate_step(posSlice)
re-invalidated posSupportMaterial but not posSimplifySupportPath, so after
any re-slice the regenerated support paths were exported unsimplified.
posSimplifySupportPath is now in that list.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
The clang-tidy job on #14394 fails on 129 misc-include-cleaner findings:
the belt sources and tests use std::, Eigen, Point/PrintConfig and
BeltBrim symbols without including the header that provides them, which
only compiled because the precompiled header supplied it. Every include
the job names is added, in each file's existing include style ("../" in
the GCode/ and Support/ subdirectories, quoted libslic3r/ paths in the
GUI and tests). No code changes.
Verified with scripts/clang_tidy_diff.py -p build-tidy --base eb5b9a77b9
(SLIC3R_PCH=OFF compile database, clang-tidy 22.1.8): no findings left.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01L6Kg5igmmMU2YLoK6HrsWV
Deterministic tests for: coincident brim at first belt contact not dropped
(C), single- and multi-extruder brim tool selection with no doubling (B),
multi-object apron ordering, inner-only+leading-only not rejecting prime
tower/spiral (D), and inner/holed + leading-edge-only geometry.
A belt printer slices in a rotated frame, so the belt surface is a tilted
plane rather than the Z=0 bed plane. Each slicing layer touches the belt
only along a narrow strip at its leading edge - about 0.2mm at 45 degrees -
so a part's first layer is really a first line, with almost no contact patch
to hold it down while the belt drags it forward. Brim was hard-disabled on
belt printers, leaving no remedy at all.
Generate the brim on the belt plane instead. The object's belt footprint is
the union over layers of each slice clipped to that layer's contact band; the
brim is offset from it in a "flattened" frame where the shear axis is
stretched by 1/cos(tilt), so ordinary Clipper offsets measure true on-belt
distance. It is emitted as cross-belt lines, one per layer band, anchored to
a fixed fraction of the band so every line shares a nozzle-to-belt clearance
and therefore comes out the same width; flow is matched to the resulting band
pitch, keeping the sheet uniform and gap-free.
Three new controls, all belt-only:
* Leading brim length - extends the brim ahead of the part along the belt,
on every downhill-facing edge of its contact area. This apron necessarily
prints BELOW the object's first layer, since layer 0 is the part's leading
contact, so it needs brim-only bands of its own.
* Extra brim width - widens the brim sideways across the belt only.
* Brim type "Leading edge only" - brim at the part's first belt contact and
nothing after it. Appended last in BrimType so no existing value shifts;
degrades to an outer brim off belt printers, with a warning.
The apron bands are lightweight records rather than a Layer subclass, so no
fabricated Layer::id() can leak into initial-layer temperature selection, the
spiral vase probe, cooling or gradual interpolation. They are generated in
posSupportMaterial because their print_z values must exist before ToolOrdering
is built at psWipeTower, and they are emitted from a short dedicated branch in
process_layer that runs before any layer pointer is dereferenced.
The footprint is closed before offsetting outwards: a belt contact patch is
often a broken-up strip, and the merged offset rings of two islands closer
than 2 x brim_width would otherwise fill the space between them - space that
lies under the part.
Also fixes a pre-existing bug where PrintObject::get_first_layer_bbox()
overwrote a valid bbox with an unassigned one on any belt printer with a brim
configured, because has_brim() was true while make_brim() returned early.
Belt brim is refused alongside the prime tower and spiral vase, and requires
one instance per PrintObject - translating an instance along the belt axis
changes its physical belt-floor Z. Untilted belt printers are unchanged: they
still get no brim, since the plate brim is emitted out of skirt_brim_groups(),
which _make_skirt() never builds for a belt printer.
