* initial commit
* fix upper bounds for assemblies
* significantly less Z shift issues, still not quite tamped down yet though
* add instrumentation to logs
* finally found the issue
* update printer defaults
* Add Optimized Gyroid infill (auto-tuned wavelength + amplitude)
New infill geometry derived from FillGyroid. Two parameters are
auto-computed per-region from density, line spacing, and layer height
(no user inputs):
omega = sqrt(density_adj) / sqrt(1 + layer_height/spacing)
clamped to [0.5, 2.0]
-- Euler-Bernoulli buckling: critical load ~ 1/L^2,
so shorter wavelength under higher load (denser infill)
raises buckling resistance.
amplitude = 0.55 / omega^2, clamped to [0.20, 0.65]
-- Curved-beam bending stress: peak stress ~ A * omega^2,
so amplitude is reduced as omega rises to keep peak
fiber stress bounded while preserving stiffness.
Files:
- src/libslic3r/Fill/FillOptimizedGyroid.{hpp,cpp} (new)
- src/libslic3r/Fill/FillBase.cpp (factory case)
- src/libslic3r/Fill/Fill.cpp (switch case)
- src/libslic3r/Layer.cpp (switch case)
- src/libslic3r/PrintConfig.{hpp,cpp} (enum + label)
- src/libslic3r/CMakeLists.txt (build sources)
User-facing: appears as "Optimized Gyroid" in the Fill Pattern dropdown.
Density still chosen by user; omega/amplitude are internal.
* Fix build: layer_height is in FillParams, not Fill base
* Add ipOptimizedGyroid to multiline infill list in ConfigManipulation
* Refactor: replace ipOptimizedGyroid enum with gyroid_optimized boolean
Per @RF47's review feedback, fold the optimized wave math into FillGyroid
itself behind a per-region boolean instead of a separate infill enum.
What changes:
- New ConfigOptionBool "gyroid_optimized" on PrintRegionConfig (default
false). When unchecked, gyroid behavior is byte-identical to before.
- Optimized wave math (compute_omega_factor, compute_amplitude_factor,
f_opt, make_*_opt, make_optimized_gyroid_waves) lives inside
FillGyroid.cpp. _fill_surface_single branches on params.gyroid_optimized.
- FillParams gains a bool gyroid_optimized field, populated in Fill.cpp
from region_config alongside fill_multiline.
- UI checkbox added under Strength > Infill in Tab.cpp, label
"Optimize gyroid wave (experimental)". Toggle is hidden by
ConfigManipulation when sparse_infill_pattern != ipGyroid.
- "gyroid_optimized" added to s_Preset_print_options for preset I/O.
What goes away:
- ipOptimizedGyroid enum value, factory case, switch cases, dropdown
label, string key.
- FillOptimizedGyroid.cpp / FillOptimizedGyroid.hpp (math moved into
FillGyroid.cpp).
- Net diff drops by ~250 lines.
Existing profiles using gyroid are unaffected.
* Wire gyroid_optimized through SurfaceFillParams to FillParams
Linux build failed because line 921 in Fill.cpp populates a
SurfaceFillParams (the dedup struct), not FillParams directly.
Add the field there, in operator< / operator==, and copy it to
FillParams at both conversion sites.
* Use toggle_line for gyroid_optimized: hide row when pattern != gyroid
* Account for multiline wall thickness in omega correction (per @RF47)
When fill_multiline = N, each gyroid wall is N lines thick, so the
geometric scale fed into the buckling correction term should be
spacing * N rather than spacing. Increases omega (tighter wavelength)
when multiline is enabled, consistent with the thicker wall being
more buckling-resistant.
* Optimized gyroid via marching squares on the implicit scalar field
Per @RF47 review: replace the analytical f_opt / make_one_period_opt
wave generator (which had visible kinks at vertical-horizontal
transitions) with a marching-squares iso-extraction on the gyroid
scalar field, modeled on FillTpmsFK.cpp.
- New marchsq::GyroidField in FillGyroid.cpp evaluates
F(x,y,z) = sin(fx*x)cos(fy*y) + sin(fy*y)cos(fz*z) + sin(fz*z)cos(fx*x)
where fx = omega * baseline (anisotropic in x), fy = fz = baseline.
- get_gyroid_polylines() runs marching squares at iso=0 and converts
rings to polylines.
- _fill_surface_single() optimized branch now builds GyroidField,
runs marching squares, and skips the bb.min translate (field
output is already in absolute coords).
- Dropped: f_opt, make_one_period_opt, make_wave_opt,
make_optimized_gyroid_waves, compute_amplitude_factor. Amplitude
has no clean analog in iso-zero extraction.
- Standard (non-optimized) gyroid path unchanged.
* Mass calibration: compensate period by cbrt(omega) for x-anisotropic field
Per @RF47: optimized vs standard gyroid had different masses at the
same sparse_infill_density setting. Cause: scaling fx by omega while
leaving fy=fz at the baseline raised the surface-area-to-volume ratio
by approximately omega^(1/3) (the geometric mean of the three
frequencies).
Fix: multiply the base period by cbrt(omega) so the geometric mean of
(fx, fy, fz) returns to the standard baseline. Net effect:
fx = omega^(2/3) * baseline_orig
fy = fz = omega^(-1/3) * baseline_orig
which preserves total mass at the same density setting while
preserving the load-direction anisotropy this PR introduces.
* Switch optimized gyroid anisotropy from X to Z (per @RF47)
Z is the typical compression-load axis for FFF parts and is not at
delamination risk under compression — so the dominant failure mode
is column buckling of the vertical strands themselves. Tightening
fz directly shortens the effective vertical strand length, which
improves Z-axis buckling resistance.
Mass calibration via cbrt(omega) period compensation still applies
(scaling exactly one of three frequencies by omega; the geometric-
mean preservation argument is symmetric across axes).
* Update src/slic3r/GUI/Tab.cpp
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
* Address review feedback (Copilot + @RF47)
- Fill.cpp: gate params.gyroid_optimized on (params.pattern == ipGyroid)
so non-gyroid surfaces don't differ in SurfaceFillParams by an
irrelevant flag (would unnecessarily split fill batching).
[Copilot suggestion, RF47 confirmed correct]
- PrintConfig.cpp: drop "amplitude" from the tooltip; only wavelength
is parameterized (the marching-squares iso=0 extraction is invariant
to a uniform field scale, so amplitude has no effect).
- FillBase.hpp: shorten gyroid_optimized comment to match the actual
carried state (no amplitude term).
- FillGyroid.cpp: shorten the marchsq namespace comment block; the
ODR concern was overstated (FillTpmsFK uses the same pattern fine).
* Drop redundant marchsq bb expansion (Copilot)
bb is already offset by 10 * scale_(spacing) above for edge-artifact
margin; the second offset on bb_field doubled the raster area for no
geometric benefit and hurt CPU time on large parts.
* Update src/slic3r/GUI/Tab.cpp
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
* Fix density mismatch + rename to Z-buckling bias optimization
Issue (per @ianalexis): at the same sparse_infill_density setting,
the optimized branch produced denser fill than standard. Verified via
Python sim (sim_gyroid_compare.py) using marching squares on the
implicit field across multiple z slices.
Root cause: the omega formula was inverted from the buckling-physics
intent. The naive sqrt(density_adj) factor produced omega < 1 at
typical print densities (10-30%), which LENGTHENED the Z wavelength
instead of shortening it -- net loss in both mass and strength.
Fix:
- compute_omega_factor: invert to sqrt(1 / density_adj), clamp to
[1.0, 2.0]. Now omega = 2.0 at low density (long strands need
most help) and clamps to 1.0 above ~30% density (no-op, since
standard gyroid is already short enough).
- Remove the cbrt(omega) period compensation. Empirically (sim
table embedded in FillGyroid.cpp comment) the inverted formula
keeps line length per area at ~1.000 of standard across all
densities with no period scaling needed.
Predicted gains (sim, Z-axis Euler buckling proxy):
density line/std strength/std
10% 1.000 2.84x
15% 1.000 1.89x
20% 1.000 1.42x
30%+ 1.000 1.00x (no-op)
Rename per @ianalexis: "Optimize gyroid wave" oversells (now no-op
above 30% density and Z-only). Renamed user-facing label to
"Z-buckling bias optimization (experimental)" with updated tooltip
that scopes to vertical compression and discloses the density cutoff.
Internal config key (gyroid_optimized) unchanged for diff size.
Real-world Instron compression tests at Brown's Prince Lab to follow.
---------
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
* clean up UI elements
* further cleaning
* final cleanup for first round of settings UI streamlining
* update generic belt printer settings
* fix generic again
Reconciles the belt-printer branch with upstream PRs through #13723. Six
files had conflicts; three additional files needed manual follow-up fixes
where the auto-merge produced code that referenced upstream-renamed fields
or changed function signatures.
Notable reconciliations:
- TreeSupport.cpp: kept belt-floor early-exit branches around HEAD's
drop-down logic, folded upstream's `(distance_to_top > 0 ? 1 : 0)`
formula into the non-belt-floor path (upstream PR #11812). Dropped dead
`roof_enabled`/`force_tip_to_roof` locals.
- TreeSupport3D.cpp: combined upstream's safety-offset + remove_small
changes with HEAD's belt-floor clip in the per-slice trim loop. Dropped
HEAD's `else` block (superseded by upstream's rewritten bottom-contact
propagation) and re-added the belt-floor clip into the new propagation
loop. Gated the propagation on belt printers to prevent OOM when
belt-floor clipping produces empty initial slices.
- TriangleSelector.{cpp,hpp}: merged both new `select_patch` parameters
(HEAD's `up_direction` and upstream's `select_partially`); body uses
`dot(up_direction)` for the overhang angle check and forwards
`select_partially` to `select_triangle`.
- SupportMaterial.cpp: `slicing_params.soluble_interface` →
`zero_gap_interface_bottom` in HEAD's `detect_belt_floor_bottom_contacts`,
matching upstream's same-purpose rename at line 2495.
- Custom.json, GCodeWriter.cpp: simple additive merges (kept entries /
includes from both sides).
Verified by building OrcaSlicer (RelWithDebInfo) after a full deps
rebuild (Eigen v5.0.1, libigl v2.6.0 are now managed deps) and slicing
a scaled Benchy on the NORMALIZER belt-printer profile without OOM.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
* minor logic swap
* first attempt, has a race condition
* fixed the offset issue
* found a solution, I think things work now (at least once I quash this race condition)
* still chasing down race conditions
* add manual shear / scale order strategy swap
* tweak manual shear, fix ui uninitialization crash
* fix z height / g-code desync issue
* fix shear then scale cutoff planes
* getting closer
* fix support termination planes
* fix incorrect offsets in shear-then-scale mode
* test - fix overextrusion due to model/layer scale
Fix a regression that second extruder settings not properly handled for H2D/X2D (OrcaSlicer/OrcaSlicer#13559)
The problem here is how it deals with comparasion between signed & unsigned unmbers. It will convert both into unsigned then do the comparasion,
which means when `extruder_id` is `-1` (which is a valid value, means all extruders), it will be treated as `0xFFFFFFFF` which is obviously greater than `nozzle_volumes->size()`
then be reset to `0`. So when the parameter dialog is built (which will call this function with `extruder_id=-1`), only the first extruder will be set to the correct variant index.
* Base IS Machine
* Toggle line
* Rebase
* Intento 1
* Wiki IS
* Flavorized
* Tooltips
* Calibration using the same list
* max
* Reorder JD validation
* Refactor set input shaping
* Calibrations IS
* Default values
* Axis
* Orca comments
* Rename input_shaping_enable to input_shaping_emit
Refactor all references of the input shaping configuration option from 'input_shaping_enable' to 'input_shaping_emit' across the codebase. This improves clarity by better reflecting the option's purpose of controlling whether input shaping commands are emitted in the generated G-code.
Restore DONT EMIT FOR KLIPPER
* Refactor input shaping option toggling logic
Simplifies and consolidates the logic for toggling input shaping related options in TabPrinter::toggle_options(). Uses a loop to handle enabling/disabling lines based on GCode flavor compatibility, and refines the conditions for toggling individual options.
* Improve input shaping option toggling logic in TabPrinter
* GrayOut Emit to gcode limits for klipper
* Typo
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Typo
* Skip Y input-shaper when type is Disable
If marlin2 and disabled it will be already disabled at X.
* IS expert
Co-Authored-By: SoftFever <softfeverever@gmail.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Fixed PrintConfig.hpp order so Repetier outputs, updated ConfigWizard to use gcode_flavor value rather than static
Add Repetier to enum values and labels
Update to add Repetier base profile to the setup wizard
Re-order gcode_flavors in PrintConfig.hpp and PrintConfig.cpp to match
Revise ConfigWizard.cpp to use gcode_flavor rather than list order
Add Repetier profiles and include in custom.json (profile disables m73 and stop emit machine limits which Repetier doesn't use)
* Fix JSON formatting in Custom.json
* Add support for pressure advance in Repetier flavor
* Add Repetier flavor show motion ability tab is visible
* Refactor jerk handling for Repetier flavor
* Update resources/profiles/Custom/machine/MyRepetier 0.4 nozzle.json
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update resources/profiles/Custom/machine/fdm_repetier_common.json
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/libslic3r/PrintConfig.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* add back localisation flag for Klipper
* tidy up indentation and braces
* Space indentation for Repetier profiles changed to tab
* Fix space indentation in Custom.json file for Repetier profiles
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
Warn for first and other layers big temperature delta
Warn user if temperature differences (first layer vs other layers) for nozzle and plates are above a certain delta.
Co-authored-by: SoftFever <softfeverever@gmail.com>
Conflicts resolved in src/libslic3r/GCode.cpp and src/slic3r/GUI/GUI_Factories.cpp.
GCode.cpp: combined upstream's air-filtration per-extruder gating
(activate_air_filtration_during_print / _on_completion), the new
extrusion-role-change gcode lambda, ZAA's path.z_contoured arc-fit
disable, raft-aware slow_down_layers branch, and Vec3d/Line3 ZAA
plumbing with the local belt-printer changes (path_on_first_layer,
effective_layer_index_for_point, should_disable_arc_fitting). All
auto-merged m_writer.X() calls converted to m_writer->X() to match
the local unique_ptr<GCodeWriter> refactor.
GUI_Factories.cpp: inserted brim_flow_ratio in the Support category
list and renumbered around the local build_plate_tilt_x/y entries.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* Add OrcaCloud sync platform and preset bundle sharing system
Introduce OrcaCloud, a cloud sync platform for user presets, alongside
a preset bundle system that enables sharing printer/filament/process
profiles as local exportable bundles or subscribed cloud bundles.
OrcaCloud platform:
- Auth to Orca Cloud
- Encrypted token storage (file-based or system keychain)
- User preset sync with
- Profile migration from default/bambu folders on first login
- Homepage integration with entrance to cloud.orcaslicer.com
Preset bundles:
- Local bundle import/export with bundle_structure.json metadata
- Subscribed cloud bundles with version-based update checking
- Thread-safe concurrent bundle access with read-write mutex
- Canonical bundle preset naming (_local/<id>/... and _subscribed/<id>/...)
- Bundle presets are read-only; grouped under subheaders in combo boxes
- PresetBundleDialog with auto-sync toggle, refresh, update notifications
- Hyperlinked bundle names to cloud bundle pages
Co-authored-by: Sabriel Koh <sabrielkcr@gmail.com>
Co-authored-by: Derrick <derrick992110@gmail.com>
Co-authored-by: Mykola Nahirnyi <mnahirnyi@amcbridge.com>
Co-authored-by: Ian Chua <iancrb00@gmail.com>
Co-authored-by: Draginraptor <draginraptor@gmail.com>
Co-authored-by: ExPikaPaka <112851715+ExPikaPaka@users.noreply.github.com>
Co-authored-by: Ian Bassi <ian.bassi@outlook.com>
Co-authored-by: Ocraftyone <Ocraftyone@users.noreply.github.com>
Co-authored-by: yw4z <ywsyildiz@gmail.com>
Co-authored-by: peterm-m <101202951+peterm-m@users.noreply.github.com>
* Fixed an issue on Windows it failed to login Orca Cloud with Google account
* Elefant foot compensation for solid layers
Elefant foot compensation for solid layers above bottommost by infill density manipulation.
* Update Fill.cpp
* change the option to expert cat
* use is_approx for float
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Add extrusion role change G-code options
Introduces new G-code options for handling extrusion role changes at the process and filament levels. Updates configuration, GUI, and GCode logic to support 'process_change_extrusion_role_gcode' and 'filament_change_extrusion_role_gcode', allowing custom G-code insertion when the extrusion role changes.
Co-Authored-By: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
* Optimize extrusion role-change gcode handling
Cache gcode template strings and current filament id, and guard creation of DynamicConfig/placeholder processing behind a check that at least one role-change gcode is non-empty. This avoids redundant config lookups and DynamicConfig/placeholder parsing when no custom role-change gcode is defined, improving clarity and performance without changing behavior.
---------
Co-authored-by: Rodrigo Faselli <162915171+RF47@users.noreply.github.com>
Joseph Robertson