The shared estimate reserved every tower with one volume-per-purge rule
and the stability floor. Both planners do more: WipeTower (Type1) wipes
each filament's own prime volume in whole lines, one block per
adhesiveness category sized by its worst layer, rams the leaving
filament at every nozzle change, and squares a rib tower from the
planned depth; WipeTower2 (Type2) spaces its lines by
wipe_tower_extra_spacing, not the Type1-only infill gap, and its extra
flow cancels out of the depth. Both extend the ribs rather than the body
below the stability minimum, size every layer including a thinner first
one, and lay the brim in whole loops, WipeTower reporting half a spacing
of line width on top.
All of that now lives in estimate_wipe_tower_footprint, fed the planner
(resolve_wipe_tower_type mirrors Print::wipe_tower_type and the CLI's
Bambu Lab detection) and the filament ids rather than a count. Print
passes its own tool set; the PartPlate adapter derives the plate's ids
from the passed config and treats an explicit count as a floor, so the
CLI's count-only callers size per filament too. The placement clamp also
reserves a Type2 cone's base bulge, which the body box does not cover.
The planner-mirroring helpers sit beside the planners in WipeTower and
WipeTower2 so the two stay in sync; the libslic3r cases pin them to
footprints measured from generated G-code.
The placement clamps and the tower-approach router both stood in the bed's
bounding box for the bed itself, so on a delta or hexagonal bed the prime tower
could be parked in a corner that does not exist and the nozzle could be routed
across it. Both now test the real printable outline, slicing reports a tower
that does not fit instead of printing it off the bed, and a tower parked near an
edge is routed along the clamped side rather than falling back to a straight
line across the tower.
Also fixes the placement validation rotating the tower hull by degrees read as
radians about the plate origin, and never rotating the generated tower footprint
at all.
The wipe tower's "Delay after unloading" never happened on Klipper. It was
emitted as G4 S<seconds>, and Klipper's G4 reads only the P parameter, in
milliseconds, so the pause was silently skipped. The option now produces a
dwell Klipper actually performs.
Also corrects the planner flush rationale, which cited an extruder position
reset that Klipper resolves at parse time and does not need synchronized, and
adds end-to-end coverage that slices a two-filament print and checks the
emitted wipe tower G-code on both a Klipper and a non-Klipper flavor.
No change to any other firmware flavor's output, and no shipped profile sets a
non-zero delay, so no shipped profile's output moves either.
The wipe tower emitted G4 S0 to make the firmware finish its queued moves
before commands that must not take effect early. Klipper's G4 reads only the
P parameter, so that flush never happened there and a temperature change could
land seconds ahead of the moves it was meant to follow. Klipper now gets M400
instead, through one helper shared by both wipe tower implementations.
No change to any other firmware flavor's output, so no shipped profile or saved
project is affected.
- WipeTower: use filament_ramming_volumetric_speed(_nc) for ramming, falling back to
max_vol_speed only when nil; gate precool temps on enable_pre_heating
- ToolOrderUtils: disable the inter-layer forecast in the per-nozzle base reorder so
H2D/H2C ordering is unchanged
- PrintConfig: stop stripping filament_prime_volume in handle_legacy; document that
prime_volume drives the Type2 wipe tower and filament_prime_volume the Type1 one
- GCodeProcessor: exclude post-print end-gcode M400 dwells from the M73 estimate and
drop the dead air-filtration state
- Trim verbose BambuStudio source-location comments across the port
Wipe tower interface features and preheat fixes
Fresh PR branch rebuilt on upstream/main (squash of origin/BBL-studio-wipe-tower-merge) to avoid merge-history issues.
/run/build/BambuStudio/src/libslic3r/GCode/WipeTower.hpp:31:12: error: ‘TriangleMesh’ does not name a type
31 | static TriangleMesh its_make_rib_tower(float width, float depth, float height, float rib_length, float rib_width, bool fillet_wall);
| ^~~~~~~~~~~~
<snip>
/run/build/BambuStudio/src/libslic3r/GCode/WipeTower.hpp:33:12: error: ‘Polygon’ does not name a type
33 | static Polygon rib_section(float width, float depth, float rib_length, float rib_width, bool fillet_wall);
| ^~~~~~~
<snip>
/run/build/BambuStudio/src/libslic3r/GCode/WipeTower.hpp:200:21: error: ‘Polylines’ was not declared in this scope
200 | std::map<float, Polylines> get_outer_wall() const
| ^~~~~~~~~
<snip>
(cherry picked from commit ea2c021427dddcddb8a4e9e41c0f649dd727fdf9)
1. set wipe tower real height
2. fix wipe tower small arc error
3. add rib_width constraint to ensure that the rib wall of the wipetower are attached to the infill.
jira: STUDIO-10540
Change-Id: Idfdc809f0236121d98587ac2a09a2ebbf5caf945
(cherry picked from commit 3a7dcfd23249571224a4d538c55907a0a5c6154d)
and fix conflict checking when the wipe tower's brim fully encloses the model
jira: STUDIO-10237, STUDIO-10296
Change-Id: I6e2a6640c06ddb6b3af700c9048fa26434411631
(cherry picked from commit b36c41e5146168325d8b7ec966eb97f1062442a7)
and fix the nozzlechange's error cleanbox.
and fix some error in interface's nozzlechangle and toolchange.
jira: none
Change-Id: I2fd5c68d90506fcb8f01f09a8246dfb5838baef4
(cherry picked from commit 6c5b63db246a1f42e34225c5561fb8b0975da53b)
and set the contact surfaces of different material types as solid,
and reduce the nozzlechange speed if it occurs at the contact surface,
and recuce the toolchange speed if it occurs at the contact surface.
jira: none
Change-Id: I884d60f4114544dfa959bd654ecc985f5fb9aac4
(cherry picked from commit ed7bfd3ff6732efe6c7e9eb96901be1db00bb3d0)
1. the nozzle change gcode use double perimeter width
2. fix the error layer height for adaptive layer height
3. limit the nozzle change speed to 50 when a bridge is detected
4. fix the error extrusion flow for filament change gcode when a bridge is detected
jira: STUDIO-10269
Change-Id: I580c618555fe19d000a56e2510a42004722c1b8b
(cherry picked from commit 5c56b43166ab32b09da31b7046efbbcbe3cbc9c8)
of the wipe tower's outer wall to use the actual outer wall path.
jira: none
Change-Id: Ib45ecbc328c88c1abe6d9e8567f715331a3ddd37
(cherry picked from commit 0a20f1fe6d6d63cdcb13bc19fd9ae553f45b6f59)
1.Add automatic calculation of the wipe_tower's brim width by height；
2.modify the min_depth_per_height and the default ridwidth
jira: none
Change-Id: Idd96bc90e8e631aa8481b559e1e9fec24c6b822f
(cherry picked from commit 4dd4e9e12c02d945a0ac3fd2020f75313c5b2cc9)
and and modify the start position for tpu
jira: none
Change-Id: I75b09e7839ddd3b9fffe77392e573e1d8caa00d5
(cherry picked from commit fce47aa8cb59fb718ff30a7c7eebda30fc83119d)
and modify the path of travel to the wipe_tower after flushing
jira:none
Change-Id: Id4b0571fd12372c59cf522c13e256c7cc4ac3565
(cherry picked from commit 17771d0fbf753dd22411ce490586958bd643264e)
and modify the min_depth_per_height
jira: none
Change-Id: I4860df661b4dd1f66677112d14e60560bc4a73be
(cherry picked from commit 00810d685d01a91b5373f3315413aaef1fe49cbc)
Ian Bassi