Fix casing of axis' names (#11258)

localization/i18n/sv/OrcaSlicer_sv.po

@@ -4842,7 +4842,7 @@ msgstr "Storlek:"
 
 #, c-format, boost-format
 msgid ""
-"Conflicts of G-code paths have been found at layer %d, z = %.2lf mm. Please "
+"Conflicts of G-code paths have been found at layer %d, Z = %.2lfmm. Please "
 "separate the conflicted objects farther (%s <-> %s)."
 msgstr ""
 
@@ -8641,12 +8641,17 @@ msgid ""
 "Are you sure to use them for support base? \n"
 msgstr ""
 
+#, fuzzy
 msgid ""
 "When using support material for the support interface, we recommend the "
 "following settings:\n"
 "0 top Z distance, 0 interface spacing, interlaced rectilinear pattern and "
-"disable independent support layer height"
+"disable independent support layer height."
 msgstr ""
+"Vid användning av stödmaterial för stödgränssnittet rekommenderar vi "
+"följande inställningar:\n"
+"0 top z-avstånd, 0 gränssnittsavstånd, koncentriskt mönster och "
+"inaktivera oberoende stödskiktshöjd."
 
 msgid ""
 "Change these settings automatically?\n"
@@ -8658,11 +8663,11 @@ msgstr ""
 "Nej - Ändra inte dessa inställningar för mig."
 
 msgid ""
-"When using soluble material for the support interface, We recommend the "
+"When using soluble material for the support interface, we recommend the "
 "following settings:\n"
-"0 top z distance, 0 interface spacing, interlaced rectilinear pattern, "
-"disable independent support layer height \n"
-"and use soluble materials for both support interface and support base"
+"0 top Z distance, 0 interface spacing, interlaced rectilinear pattern, "
+"disable independent support layer height\n"
+"and use soluble materials for both support interface and support base."
 msgstr ""
 
 msgid ""
@@ -11969,11 +11974,9 @@ msgid ""
 "option in most cases.\n"
 "\n"
 "Use Outer/Inner for the same external wall quality and dimensional accuracy "
-"benefits of Inner/Outer/Inner option. However, the z seams will appear less "
+"benefits of Inner/Outer/Inner option. However, the Z seams will appear less "
 "consistent as the first extrusion of a new layer starts on a visible "
-"surface.\n"
-"\n"
-" "
+"surface."
 msgstr ""
 
 msgid "Inner/Outer"
@@ -12413,7 +12416,7 @@ msgstr ""
 #, no-c-format, no-boost-format
 msgid ""
 "Enter the shrinkage percentage that the filament will get after cooling (94% "
-"if you measure 94mm instead of 100mm). The part will be scaled in xy to "
+"if you measure 94mm instead of 100mm). The part will be scaled in XY to "
 "compensate. Only the filament used for the perimeter is taken into account.\n"
 "Be sure to allow enough space between objects, as this compensation is done "
 "after the checks."
@@ -13133,7 +13136,7 @@ msgid "Precise Z height"
 msgstr ""
 
 msgid ""
-"Enable this to get precise z height of object after slicing. It will get the "
+"Enable this to get precise Z height of object after slicing. It will get the "
 "precise object height by fine-tuning the layer heights of the last few "
 "layers. Note that this is an experimental parameter."
 msgstr ""
@@ -14658,7 +14661,7 @@ msgid "Speed of internal solid infill, not the top and bottom surface."
 msgstr "Hastighet för inre solid ifyllnad, förrutom topp och botten ytorna"
 
 msgid ""
-"Spiralize smooths out the z moves of the outer contour. And turns a solid "
+"Spiralize smooths out the Z moves of the outer contour. And turns a solid "
 "model into a single walled print with solid bottom layers. The final "
 "generated model has no seam."
 msgstr ""
@@ -14875,8 +14878,8 @@ msgstr "normal (manuell)"
 msgid "Tree (manual)"
 msgstr "tree (manuell)"
 
-msgid "Support/object xy distance"
-msgstr "Support/objekt xy distans"
+msgid "Support/object XY distance"
+msgstr "Support/objekt XY distans"
 
 msgid "XY separation between an object and its support."
 msgstr "XY avstånd mellan objektet och support"
@@ -15083,7 +15086,7 @@ msgstr "Oberoende support lagerhöjd"
 
 msgid ""
 "Support layer uses layer height independent with object layer. This is to "
-"support customizing z-gap and save print time. This option will be invalid "
+"support customizing Z-gap and save print time. This option will be invalid "
 "when the prime tower is enabled."
 msgstr ""
 "Support lager använder lagerhöjd oberoende av objekt lager. Detta för att "
@@ -16274,7 +16277,7 @@ msgid ""
 "Contains a string with the information about what scaling was applied to the "
 "individual objects. Indexing of the objects is zero-based (first object has "
 "index 0).\n"
-"Example: 'x:100% y:50% z:100'."
+"Example: 'x:100% y:50% z:100%'."
 msgstr ""
 
 msgid "Input filename without extension"
@@ -16284,11 +16287,11 @@ msgid "Source filename of the first object, without extension."
 msgstr ""
 
 msgid ""
-"The vector has two elements: x and y coordinate of the point. Values in mm."
+"The vector has two elements: X and Y coordinate of the point. Values in mm."
 msgstr ""
 
 msgid ""
-"The vector has two elements: x and y dimension of the bounding box. Values "
+"The vector has two elements: X and Y dimension of the bounding box. Values "
 "in mm."
 msgstr ""
 
@@ -19931,17 +19934,6 @@ msgstr ""
 #~ "inställningar: minst 2 anläggnings lager, minst 0,1 mm topp z-avstånd "
 #~ "eller med support material på anläggningsytan."
 
-#~ msgid ""
-#~ "When using support material for the support interface, we recommend the "
-#~ "following settings:\n"
-#~ "0 top z distance, 0 interface spacing, concentric pattern and disable "
-#~ "independent support layer height"
-#~ msgstr ""
-#~ "Vid användning av stödmaterial för stödgränssnittet rekommenderar vi "
-#~ "följande inställningar:\n"
-#~ "0 top z-avstånd, 0 gränssnittsavstånd, koncentriskt mönster och "
-#~ "inaktivera oberoende stödskiktshöjd"
-
 #~ msgid "This setting specify the count of walls around support"
 #~ msgstr "Denna inställning anger antalet väggar runt supporten"