diff --git a/docs/HLSD/snapmaker-high-flow.md b/docs/HLSD/snapmaker-high-flow.md deleted file mode 100644 index 61da074e97..0000000000 --- a/docs/HLSD/snapmaker-high-flow.md +++ /dev/null @@ -1,108 +0,0 @@ -# Snapmaker U1 high-flow profiles - -The U1 provides separate High Flow printer presets for 0.2, 0.4, 0.6 and -0.8 mm nozzles. Each describes four tools fitted with the same diameter and -high-flow nozzle. They inherit the corresponding standard printer, retaining -its model identity, geometry, motion limits and machine G-code. Existing -standard and mixed-diameter presets retain their settings and names. - -Enable the High Flow variants under Snapmaker U1 in the printer setup, select -the matching printer, and select a filament whose name includes that diameter -and `High Flow nozzle`. PLA SnapSpeed is the default material for these -printers. Dedicated HF process presets preserve diameter-specific extrusion -widths and layer heights while overriding the four print speeds below. -Separate HF filament presets keep higher ceilings out of standard-nozzle -material settings. - -## Process speeds - -All 36 HF process presets, across 0.2, 0.4, 0.6 and 0.8 mm nozzles, -use the same requested speeds from Snorca's 0.4 mm HF Standard process: - -| Setting | Speed (mm/s) | -| --- | ---: | -| Inner walls | 600 | -| Outer walls | 500 | -| Internal solid infill | 600 | -| Sparse infill | 600 | - -Each HF process inherits its standard diameter/layer-height counterpart, -so geometry, accelerations, first-layer speeds, bridges, overhangs and other -settings remain diameter-specific. Standard printers retain their original -process speeds. HF printers default to the corresponding HF process. -Volumetric ceilings and machine motion limits still cap actual speeds. - -## Chamber and purifier control - -All U1 start sequences, including the mixed-diameter and inherited HF -profiles, issue `SET_PURIFIER_MODE` automatically. The start G-code checks the existing -`min_vitrification_temperature` placeholder, the lowest Softening temperature -(`temperature_vitrification`) among the filaments actually used on the plate: -at or below 50 C selects strong cooling, above 50 C through 70 C selects weak -cooling, and above 70 C selects keep-warm mode. Unused materials do not affect -the result. There is no extra filament flag or enable setting. - -The firmware parameters match Snorca: strong cooling uses mode 1, target -42 C, alarm 45 C, fan 0.6 and no delayed shutdown; weak cooling uses mode 3, -target 0 C, fan 0.6 and a 600-second delay; keep-warm uses mode 3, target -45 C, fan 0.6 and a 600-second delay. Mode selection happens once at print -start and depends on the accuracy of each filament's softening temperature. - -## Calibration sources - -Except for the volumetric ceiling, the original 0.4 mm HF material overrides come from Snapmaker/OrcaSlicer `snorca/main` -commit `b1831e5dcb`, under `resources/profiles/Snapmaker/filament/`. That fork -uses `filament_flow_support: ["standard", "high_flow"]` to interpret paired -values. Here the high-flow column is translated into ordinary single-valued -filament overrides; the fork-specific keys and its profile restructuring are -not imported. Companion temperature and pressure-advance enable settings are -included. Machine and filament G-code remain inherited from this branch. - -The 14 materials with upstream HF overrides are ABS, ASA, PETG HF, PETG Translucent, PETG-CF, -PLA Full Spectrum, PLA Glow, PLA Matte, PLA Silk, PLA SnapSpeed, PLA -Translucent, PLA Wood, PLA-CF and PVA. Upstream's renamed Support For PLA is -not assumed equivalent to the local Breakaway formulation. - -## Volumetric ceiling - -All 141 HF filament presets explicitly set maximum volumetric speed to three -times the fully inherited non-HF material value. Diameter-specific parents -are used where available; Generic HF presets inherit the active Orca filament -library's `@System` definitions, which are shared across diameters. The parent -is recorded in `inherits`. This replaces both the upstream 0.4 mm HF ceiling -and the earlier capped estimates. - -The ceiling is a user-selected limit, not a measured hardware capability. -Other process and machine limits still apply. Future changes to a parent -preset's volumetric speed require updating its HF child; the multiplier is -materialized in JSON, not evaluated by the slicer. - -## Other material settings - -The 24 additional HF material presets are **estimated starting points**, not -manufacturer calibrations. They exist only where this branch already has a -matching material and diameter. In particular, this does not make filled -materials available to a 0.2 mm nozzle when no such standard profile exists. - -For each material with a paired 0.4 mm standard/HF value: - -- Flow ratio and pressure advance use the 0.4 mm HF/standard ratio, - rounded to four decimal places. A zero standard value is not divided by. -- Nozzle and initial-layer temperatures use the 0.4 mm HF-minus-standard - difference, added to the diameter's original temperature. -- Pressure advance follows the source's enable setting when its value is - adjusted. Diameter-specific retraction and cooling settings are retained. -- Missing, single-valued or `nil` comparisons leave the diameter's original - setting intact. - -For example, PLA SnapSpeed has standard volumetric limits of 2 mm^3/s at -0.2 mm and 20 mm^3/s at 0.4, 0.6 and 0.8 mm. Its HF ceilings are therefore -6 and 60 mm^3/s respectively. The other 103 HF material presets retain their -standard parent's temperature, retraction, cooling and pressure-advance -settings, changing only the volumetric ceiling and profile metadata. -Each HF preset includes its baseline and ceiling in its filament notes. -Tune the material settings for the actual nozzle, filament and temperature. - -The separate preset design requires no C++ changes or new profile keys. It -does not provide independent standard/HF selection per tool within one printer -preset; a mixed hardware setup needs its own calibrated user preset. diff --git a/resources/profiles/Snapmaker/filament/Fiberon ASA-CF08 @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon ASA-CF08 @U1 0.4 High Flow nozzle.json index 794206a9ee..dc60a89080 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon ASA-CF08 @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon ASA-CF08 @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Fiberon ASA-CF08 @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Fiberon PA12-CF10 @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon PA12-CF10 @U1 0.4 High Flow nozzle.json index 40f28ecc21..ca3a3615ec 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon PA12-CF10 @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon PA12-CF10 @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Fiberon PA12-CF10 @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Fiberon PA6-CF20 @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon PA6-CF20 @U1 0.4 High Flow nozzle.json index dd15942c75..fdad376102 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon PA6-CF20 @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon PA6-CF20 @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Fiberon PA6-CF20 @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Fiberon PA612-ESD @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon PA612-ESD @U1 0.4 High Flow nozzle.json index a051be58f7..bfb433d9d8 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon PA612-ESD @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon PA612-ESD @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Fiberon PA612-ESD @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Fiberon PETG-ESD @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon PETG-ESD @U1 0.4 High Flow nozzle.json index fe4411ceba..0712b95763 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon PETG-ESD @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon PETG-ESD @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Fiberon PETG-ESD @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Fiberon PPS-GF20 @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Fiberon PPS-GF20 @U1 0.4 High Flow nozzle.json index a838e2fecc..ae976bbde1 100644 --- a/resources/profiles/Snapmaker/filament/Fiberon PPS-GF20 @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Fiberon PPS-GF20 @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Fiberon PPS-GF20 @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.2 High Flow nozzle.json index f224a6e5f8..0f3180747b 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "1" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG @System: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.4 High Flow nozzle.json index 2dbdd3a6d3..dc29505cd2 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG @System: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.6 High Flow nozzle.json index 67955d8cdc..7f48563c75 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG @System: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.8 High Flow nozzle.json index 766f30a03f..e614e63e6b 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG @System: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PETG @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.2 High Flow nozzle.json index be8af80e2d..838c6f27c8 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "1" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG HF @System: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.4 High Flow nozzle.json index c13f72b1ed..15d0b70f30 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "16" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG HF @System: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.6 High Flow nozzle.json index d0fed24d19..23977d0239 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "16" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG HF @System: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.8 High Flow nozzle.json index b0b75d0a17..3a4c3ba6ad 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG HF @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "16" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG HF @System: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Generic PETG HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.4 High Flow nozzle.json index 9ce1f45d0e..55dd20fa73 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "34.5" + "11" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG-CF @System: 11.5 x 3 = 34.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 11 mm^3/s, from Snorca standard preset Generic PETG-CF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.6 High Flow nozzle.json index 6ecdd1894b..98a3e9f0ca 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "34.5" + "11.5" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG-CF @System: 11.5 x 3 = 34.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.8 High Flow nozzle.json index 95c852bdf8..c9fb8439ec 100644 --- a/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PETG-CF @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "34.5" + "11.5" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PETG-CF @System: 11.5 x 3 = 34.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 11.5 mm^3/s, from Snorca standard preset Generic PETG-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.2 High Flow nozzle.json index fa8f00af48..f4c562111c 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "1.6" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Generic PLA @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.4 High Flow nozzle.json index e564663de8..3042cc6942 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.6 High Flow nozzle.json index e964a2d73c..05b104ad69 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.8 High Flow nozzle.json index 0576e76d5f..b4962c3d93 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.2 High Flow nozzle.json index 2ab997f82f..b092b41fd8 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "2" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA High Speed @System: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.4 High Flow nozzle.json index 4a30c36707..3cc254811a 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA High Speed @System: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.6 High Flow nozzle.json index c26c6d1d75..68520dfb6e 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA High Speed @System: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.8 High Flow nozzle.json index 8350a79674..7941e63d2c 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA High Speed @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA High Speed @System: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Generic PLA High Speed @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.2 High Flow nozzle.json index 66e30d591e..7103c2aebe 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "2" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA Silk @System: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.4 High Flow nozzle.json index 960fbb7ae4..cca504c6d5 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "7.5" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA Silk @System: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.6 High Flow nozzle.json index 4749f73903..3ba3f5e0b5 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "7.5" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA Silk @System: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.8 High Flow nozzle.json index ae13436c89..dcc0bc8007 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA Silk @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "7.5" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA Silk @System: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 7.5 mm^3/s, from Snorca standard preset Generic PLA Silk @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.4 High Flow nozzle.json index 4ea4fa5854..acb4001897 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA-CF @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.6 High Flow nozzle.json index 6489d4c06e..e0b91c6b08 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA-CF @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.8 High Flow nozzle.json index d8a21dc0ff..5e33595604 100644 --- a/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic PLA-CF @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic PLA-CF @System: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Generic PLA-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.4 High Flow nozzle.json index af86177bce..0e28741d4b 100644 --- a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic TPU @System: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.6 High Flow nozzle.json index 3bb797471f..8a1e5c04ff 100644 --- a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic TPU @System: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.8 High Flow nozzle.json index 88d4a980f1..34adb046aa 100644 --- a/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Generic TPU @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Uses the active Orca Generic material settings. Volumetric speed ceiling is 3x Generic TPU @System: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Uses the active Orca Generic material settings. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Generic TPU @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma CoPE @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma CoPE @U1 0.4 High Flow nozzle.json index e9de9fd91a..d0bccc66e1 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma CoPE @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma CoPE @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset Panchroma CoPE @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA @U1 0.4 High Flow nozzle.json index b57e11d9ae..783dea1078 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Celestial @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Celestial @U1 0.4 High Flow nozzle.json index 23888f197d..9b0df8dd59 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Celestial @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Celestial @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Celestial @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Galaxy @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Galaxy @U1 0.4 High Flow nozzle.json index 7f77834c25..4eb0005363 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Galaxy @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Galaxy @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Galaxy @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Glow @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Glow @U1 0.4 High Flow nozzle.json index 6becd42d5e..57f7e80c9c 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Glow @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Glow @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Glow @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Luminous @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Luminous @U1 0.4 High Flow nozzle.json index e7c1666d92..e892c5c2f7 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Luminous @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Luminous @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Luminous @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Marble @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Marble @U1 0.4 High Flow nozzle.json index 7ed7b808a2..d9f9f9c419 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Marble @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Marble @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset Panchroma PLA Marble @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Matte @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Matte @U1 0.4 High Flow nozzle.json index 42fb688f20..145f766ce9 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Matte @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Matte @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset Panchroma PLA Matte @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Metallic @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Metallic @U1 0.4 High Flow nozzle.json index fb1c10a2bc..b54b291bdd 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Metallic @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Metallic @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Metallic @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Neon @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Neon @U1 0.4 High Flow nozzle.json index fa9087b701..da0389bdc7 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Neon @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Neon @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Neon @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Satin @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Satin @U1 0.4 High Flow nozzle.json index 970adef497..2f705909e8 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Satin @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Satin @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset Panchroma PLA Satin @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Silk @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Silk @U1 0.4 High Flow nozzle.json index 47f12bcfd8..9553afb7e3 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Silk @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Silk @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Panchroma PLA Silk @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Starlight @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Starlight @U1 0.4 High Flow nozzle.json index d0a4cdee65..4d8310a6c3 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Starlight @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Starlight @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Starlight @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Temp Shift @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Temp Shift @U1 0.4 High Flow nozzle.json index fca32afa7b..5cefff25f1 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Temp Shift @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Temp Shift @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Temp Shift @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA Translucent @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA Translucent @U1 0.4 High Flow nozzle.json index f6a4f0bfc3..45102a7a19 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA Translucent @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA Translucent @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA Translucent @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Panchroma PLA UV Shift @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Panchroma PLA UV Shift @U1 0.4 High Flow nozzle.json index 295bee1ea0..d252f70921 100644 --- a/resources/profiles/Snapmaker/filament/Panchroma PLA UV Shift @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Panchroma PLA UV Shift @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Panchroma PLA UV Shift @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite CosPLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite CosPLA @U1 0.4 High Flow nozzle.json index 6ed9b9543d..7af0ba9b3a 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite CosPLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite CosPLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset PolyLite CosPLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PETG @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PETG @U1 0.4 High Flow nozzle.json index 0616e2fba3..cc4623a7cd 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PETG @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PETG @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "7.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.5 mm^3/s, from local standard fallback preset PolyLite PETG @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PETG Translucent @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PETG Translucent @U1 0.4 High Flow nozzle.json index b7dee44938..f0b3f91f49 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PETG Translucent @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PETG Translucent @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.5" + "7.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.5 x 3 = 22.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.5 mm^3/s, from local standard fallback preset PolyLite PETG Translucent @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA @U1 0.4 High Flow nozzle.json index b337a5abc3..3d3a9bef72 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Galaxy @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Galaxy @U1 0.4 High Flow nozzle.json index d2669f41a3..3836e62d5e 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Galaxy @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Galaxy @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Galaxy @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Glow @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Glow @U1 0.4 High Flow nozzle.json index 748fe5e2c6..f73ede7b25 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Glow @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Glow @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Glow @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Luminous @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Luminous @U1 0.4 High Flow nozzle.json index 7c7c661948..2ab15e9fd2 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Luminous @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Luminous @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Luminous @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Neon @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Neon @U1 0.4 High Flow nozzle.json index 8aee23d539..51d1010112 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Neon @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Neon @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Neon @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Pro @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Pro @U1 0.4 High Flow nozzle.json index 0320f700c6..9b250dfb98 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Pro @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Pro @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Pro @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Pro Metallic @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Pro Metallic @U1 0.4 High Flow nozzle.json index f3a964bebb..fbfb23ac4b 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Pro Metallic @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Pro Metallic @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset PolyLite PLA Pro Metallic @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Starlight @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Starlight @U1 0.4 High Flow nozzle.json index efcfd1518e..e1502b10de 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Starlight @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Starlight @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Starlight @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyLite PLA Translucent @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyLite PLA Translucent @U1 0.4 High Flow nozzle.json index 06e0a310c7..c44e1bb633 100644 --- a/resources/profiles/Snapmaker/filament/PolyLite PLA Translucent @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyLite PLA Translucent @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset PolyLite PLA Translucent @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyTerra PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyTerra PLA @U1 0.4 High Flow nozzle.json index e2c1f0aa26..454b86d711 100644 --- a/resources/profiles/Snapmaker/filament/PolyTerra PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyTerra PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset PolyTerra PLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyTerra PLA Marble @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyTerra PLA Marble @U1 0.4 High Flow nozzle.json index e9bf977e66..4bfbd99b94 100644 --- a/resources/profiles/Snapmaker/filament/PolyTerra PLA Marble @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyTerra PLA Marble @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset PolyTerra PLA Marble @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/PolyTerra PLA+ @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/PolyTerra PLA+ @U1 0.4 High Flow nozzle.json index 274caf962e..20cb320ec8 100644 --- a/resources/profiles/Snapmaker/filament/PolyTerra PLA+ @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/PolyTerra PLA+ @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset PolyTerra PLA+ @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker General PLA Family @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker General PLA Family @U1 0.4 High Flow nozzle.json index c36940b325..2c0f8a6936 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker General PLA Family @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker General PLA Family @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Polymaker General PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker HT-PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker HT-PLA @U1 0.4 High Flow nozzle.json index 1bd1c95108..d6d336c3e0 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker HT-PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker HT-PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker HT-PLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker HT-PLA-GF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker HT-PLA-GF @U1 0.4 High Flow nozzle.json index 844fc2e463..0d76705426 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker HT-PLA-GF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker HT-PLA-GF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker HT-PLA-GF @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker PETG @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker PETG @U1 0.4 High Flow nozzle.json index d15778711a..f2b8f17ca2 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker PETG @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker PETG @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker PETG @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker PETG Galaxy @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker PETG Galaxy @U1 0.4 High Flow nozzle.json index 99eae4584a..afc5f6a361 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker PETG Galaxy @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker PETG Galaxy @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker PETG Galaxy @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker PLA @U1 0.4 High Flow nozzle.json index 066c4e5d48..b411e8960a 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 20 mm^3/s, from local standard fallback preset Polymaker PLA @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker PLA Pro @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker PLA Pro @U1 0.4 High Flow nozzle.json index d1c63bc805..0c98d9a7ee 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker PLA Pro @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker PLA Pro @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker PLA Pro @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker PLA Pro Metallic @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker PLA Pro Metallic @U1 0.4 High Flow nozzle.json index c7e944ea35..b027a554b2 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker PLA Pro Metallic @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker PLA Pro Metallic @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Polymaker PLA Pro Metallic @Snapmaker U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker Silk PLA Family @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker Silk PLA Family @U1 0.4 High Flow nozzle.json index c60d41257c..c51dce398d 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker Silk PLA Family @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker Silk PLA Family @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Silk PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Polymaker Tough PLA Family @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Polymaker Tough PLA Family @U1 0.4 High Flow nozzle.json index 4a539098ca..724ab002c2 100644 --- a/resources/profiles/Snapmaker/filament/Polymaker Tough PLA Family @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Polymaker Tough PLA Family @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Polymaker Tough PLA Family @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker ABS @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker ABS @U1 0.4 High Flow nozzle.json index e3b53f36f3..0de983e448 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker ABS @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker ABS @U1 0.4 High Flow nozzle.json @@ -18,7 +18,7 @@ "10" ], "filament_max_volumetric_speed": [ - "24" + "22" ], "filament_minimal_purge_on_wipe_tower": [ "15" @@ -45,6 +45,6 @@ "280" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ABS @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker ABS Benchy @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker ABS Benchy @U1 0.4 High Flow nozzle.json index 244351878e..f8c91285b6 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker ABS Benchy @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker ABS Benchy @U1 0.4 High Flow nozzle.json @@ -9,10 +9,10 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "93" + "31" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 31 x 3 = 93 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 31 mm^3/s, from local standard fallback preset Snapmaker ABS Benchy @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "compatible_prints": [ "0.25 Benchy @Snapmaker U1 (0.4 High Flow nozzle)" diff --git a/resources/profiles/Snapmaker/filament/Snapmaker ASA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker ASA @U1 0.4 High Flow nozzle.json index c5199df011..212e9b1044 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker ASA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker ASA @U1 0.4 High Flow nozzle.json @@ -18,7 +18,7 @@ "10" ], "filament_max_volumetric_speed": [ - "24" + "22" ], "filament_minimal_purge_on_wipe_tower": [ "15" @@ -45,6 +45,6 @@ "0.02" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 22 mm^3/s, from Snorca HF preset Snapmaker ASA @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.2 High Flow nozzle.json index 3fff84663e..9fa11d6101 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "1.5" + "0.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 0.5 x 3 = 1.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 0.5 mm^3/s, from local standard fallback preset Snapmaker Breakaway Support For PLA @U1 0.2 nozzle; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.4 High Flow nozzle.json index 871d785016..9d8922829a 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Snapmaker Breakaway Support For PLA @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.6 High Flow nozzle.json index 77717f535a..63e218c554 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Snapmaker Breakaway Support For PLA @U1 0.6 nozzle; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.8 High Flow nozzle.json index 5db74011a3..dce415fefe 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker Breakaway Support For PLA @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Snapmaker Breakaway Support For PLA @U1 0.8 nozzle; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PA-CF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PA-CF @U1 0.4 High Flow nozzle.json index f6981095b8..c097954185 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PA-CF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PA-CF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "24" + "8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 8 x 3 = 24 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 8 mm^3/s, from local standard fallback preset Snapmaker PA-CF @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PET @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PET @U1 0.4 High Flow nozzle.json index 854a02c1d1..a7c30b3000 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PET @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PET @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "20.4" + "6.8" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 6.8 x 3 = 20.4 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 6.8 mm^3/s, from local standard fallback preset Snapmaker PET @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG @U1 0.4 High Flow nozzle.json index 780f8fee71..bf18d6fb9d 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "10" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10 mm^3/s, from local standard fallback preset Snapmaker PETG @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.2 High Flow nozzle.json index 91b263df44..6fded62f26 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.2 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "3" + "2" ], "filament_flow_ratio": [ "0.955" @@ -24,6 +24,6 @@ "1" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 1 x 3 = 3 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.4 High Flow nozzle.json index 085debf589..5b562ef932 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.4 High Flow nozzle.json @@ -21,7 +21,7 @@ "0.955" ], "filament_max_volumetric_speed": [ - "48" + "30" ], "filament_minimal_purge_on_wipe_tower": [ "50" @@ -63,6 +63,6 @@ "0.035" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 30 mm^3/s, from Snorca HF preset Snapmaker PETG HF (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.6 High Flow nozzle.json index ca27f67555..1bb8fca6dd 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.6 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_flow_ratio": [ "0.955" @@ -24,6 +24,6 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.8 High Flow nozzle.json index 051bb8fbac..b95ecd4911 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG HF @U1 0.8 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_flow_ratio": [ "0.955" @@ -24,6 +24,6 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PETG HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.2 High Flow nozzle.json index 44f49f7b2d..eec95f80bf 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.2 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 1 x 3 = 3 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "3" + "1" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.4 High Flow nozzle.json index 265b504a53..1a17739f69 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.4 High Flow nozzle.json @@ -15,9 +15,9 @@ "0.05" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 10 mm^3/s, from Snorca HF preset Snapmaker PETG Translucent @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "30" + "10" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.6 High Flow nozzle.json index aea3ffda1c..0fceb6ef5a 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.6 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "48" + "16" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.8 High Flow nozzle.json index 7e66c59a2c..26749c6ecf 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG Translucent @U1 0.8 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker PETG Translucent @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "48" + "16" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PETG-CF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PETG-CF @U1 0.4 High Flow nozzle.json index 4fb22fd2a5..6c06c1c4bf 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PETG-CF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PETG-CF @U1 0.4 High Flow nozzle.json @@ -24,7 +24,7 @@ "1.01" ], "filament_max_volumetric_speed": [ - "19.2" + "18" ], "filament_minimal_purge_on_wipe_tower": [ "30" @@ -60,6 +60,6 @@ "0.028" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 6.4 x 3 = 19.2 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PETG-CF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA @U1 0.4 High Flow nozzle.json index 9e52e8d145..b0e13a4f79 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "42" + "14" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 14 x 3 = 42 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 14 mm^3/s, from local standard fallback preset Snapmaker PLA @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Basic @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Basic @U1 0.4 High Flow nozzle.json index 5b690deccc..3d2e16dc7f 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Basic @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Basic @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from Snorca standard preset Snapmaker PLA Basic @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Eco @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Eco @U1 0.4 High Flow nozzle.json index 1fc7f3e6e5..100d225a88 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Eco @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Eco @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from local standard fallback preset Snapmaker PLA Eco @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Full Spectrum @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Full Spectrum @U1 0.4 High Flow nozzle.json index d9b39fcdb2..1a63ff75cc 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Full Spectrum @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Full Spectrum @U1 0.4 High Flow nozzle.json @@ -24,9 +24,9 @@ "0.024" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 15 mm^3/s, from Snorca HF preset Snapmaker PLA Full Spectrum @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "45" + "15" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Glow @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Glow @U1 0.4 High Flow nozzle.json index d6423ff5ff..b2f4efcfb1 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Glow @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Glow @U1 0.4 High Flow nozzle.json @@ -15,12 +15,12 @@ "0.98" ], "filament_max_volumetric_speed": [ - "48" + "18" ], "pressure_advance": [ "0.023" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 18 mm^3/s, from Snorca HF preset Snapmaker PLA Glow @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Lite @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Lite @U1 0.4 High Flow nozzle.json index 6f7f024b4c..f281f8795b 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Lite @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Lite @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "45" + "15" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 15 mm^3/s, from local standard fallback preset Snapmaker PLA Lite @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.2 High Flow nozzle.json index a0e558096c..3b2e3541c4 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.2 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "6" + "2" ], "filament_flow_ratio": [ "1.0395" @@ -27,6 +27,6 @@ "1" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2 x 3 = 6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.4 High Flow nozzle.json index b4021aea6a..45bf88f8b5 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.4 High Flow nozzle.json @@ -18,7 +18,7 @@ "0.99" ], "filament_max_volumetric_speed": [ - "66" + "40" ], "filament_retraction_length": [ "1" @@ -39,6 +39,6 @@ "0.024" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 22 x 3 = 66 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA Matte @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.6 High Flow nozzle.json index daef1b37d5..2430b54a9d 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.6 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_flow_ratio": [ "0.9801" @@ -27,6 +27,6 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.8 High Flow nozzle.json index 7f36cee705..38aed6438a 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Matte @U1 0.8 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "filament_flow_ratio": [ "0.9702" @@ -27,6 +27,6 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Matte @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Metal @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Metal @U1 0.4 High Flow nozzle.json index c5c4b829a2..f26eeb2114 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Metal @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Metal @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "48" + "16" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 16 mm^3/s, from local standard fallback preset Snapmaker PLA Metal @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.2 High Flow nozzle.json index d110009d58..d8eba5a227 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.2 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "6" + "2" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2 x 3 = 6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.4 High Flow nozzle.json index e05d313038..96869e7af9 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.4 High Flow nozzle.json @@ -12,12 +12,12 @@ "80" ], "filament_max_volumetric_speed": [ - "30" + "12" ], "filament_z_hop_types": [ "Slope Lift" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Silk @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.6 High Flow nozzle.json index ad19b1abf3..e71fc44138 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "10" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.8 High Flow nozzle.json index 3856c5e5a2..4b8d8be438 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Silk @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "30" + "10" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 10 x 3 = 30 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 10 mm^3/s, from Snorca standard preset Snapmaker PLA Silk @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.2 High Flow nozzle.json index ef43a62cc1..dd492516fb 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.2 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.2 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "6" + "2" ], "pressure_advance": [ "0.24" @@ -18,6 +18,6 @@ "1" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2 x 3 = 6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 2 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.4 High Flow nozzle.json index 9ab350a7ba..03be272261 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.4 High Flow nozzle.json @@ -12,7 +12,7 @@ "1" ], "filament_max_volumetric_speed": [ - "60" + "40" ], "filament_multitool_ramming_flow": [ "40" @@ -21,6 +21,6 @@ "0.024" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 40 mm^3/s, from Snorca HF preset Snapmaker PLA SnapSpeed @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.6 High Flow nozzle.json index ab657264ad..8bb018713c 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.6 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "pressure_advance": [ "0.024" @@ -18,6 +18,6 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.8 High Flow nozzle.json index 5e9be868b6..6af5875213 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA SnapSpeed @U1 0.8 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "60" + "20" ], "pressure_advance": [ "0.0216" @@ -18,6 +18,6 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA SnapSpeed @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.2 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.2 High Flow nozzle.json index b7b8357798..66ea29ff0c 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.2 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.2 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 1.6 x 3 = 4.8 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.2 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 1.6 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.2 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "4.8" + "1.6" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.4 High Flow nozzle.json index 67a5c77f4a..dd3134ef2b 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.4 High Flow nozzle.json @@ -12,9 +12,9 @@ "0.024" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 12 mm^3/s, from Snorca HF preset Snapmaker PLA Translucent @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "36" + "12" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.6 High Flow nozzle.json index 29767b5045..647971457c 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.6 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "36" + "12" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.8 High Flow nozzle.json index 6790f2a521..ef2bcbe096 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Translucent @U1 0.8 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker PLA Translucent @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "36" + "12" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.4 High Flow nozzle.json index 95ef69bb13..5f3d8d6cc7 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.4 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "20" ], "filament_retract_length_toolchange": [ "6" @@ -21,6 +21,6 @@ "0.024" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA Wood @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.6 High Flow nozzle.json index 71e3f69b98..b30036af55 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.6 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "pressure_advance": [ "0.0134" @@ -18,6 +18,6 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.8 High Flow nozzle.json index 9bcde49fd5..9bbf33e51b 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA Wood @U1 0.8 High Flow nozzle.json @@ -15,9 +15,9 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 20 x 3 = 60 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 20 mm^3/s, from Snorca standard preset Snapmaker PLA Wood @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "60" + "20" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.4 High Flow nozzle.json index c61a287426..310efaefe2 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.4 High Flow nozzle.json @@ -12,7 +12,7 @@ "100" ], "filament_max_volumetric_speed": [ - "45" + "20" ], "filament_multitool_ramming_flow": [ "30" @@ -33,6 +33,6 @@ "0.02" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 15 x 3 = 45 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 20 mm^3/s, from Snorca HF preset Snapmaker PLA-CF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.6 High Flow nozzle.json index 825567e128..3fecd0e77c 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.6 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "pressure_advance": [ "0.03" @@ -24,6 +24,6 @@ "1" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.8 High Flow nozzle.json index 52100f6bbe..0f5a73930a 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PLA-CF @U1 0.8 High Flow nozzle.json @@ -9,7 +9,7 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "54" + "18" ], "pressure_advance": [ "0.03" @@ -24,6 +24,6 @@ "1" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 18 x 3 = 54 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 18 mm^3/s, from Snorca standard preset Snapmaker PLA-CF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.4 High Flow nozzle.json index e96baac97a..ca38fd6675 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.4 High Flow nozzle.json @@ -12,7 +12,7 @@ "0.97" ], "filament_max_volumetric_speed": [ - "15" + "6" ], "filament_multitool_ramming_flow": [ "10" @@ -21,6 +21,6 @@ "0.6" ], "filament_notes": [ - "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 5 x 3 = 15 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Temperature, flow ratio, pressure advance and other high-flow overrides are based on Snapmaker OrcaSlicer snorca/main b1831e5dcb for 0.4 mm nozzles. Volumetric speed ceiling: 6 mm^3/s, from Snorca HF preset Snapmaker PVA @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.6 High Flow nozzle.json index 1fb7bc978a..e5ef681dc3 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.6 High Flow nozzle.json @@ -12,9 +12,9 @@ "0.9506" ], "filament_notes": [ - "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 6 x 3 = 18 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.6 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "18" + "6" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.8 High Flow nozzle.json index cfdd941bc8..693f9a4c27 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker PVA @U1 0.8 High Flow nozzle.json @@ -12,9 +12,9 @@ "0.9312" ], "filament_notes": [ - "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 6 x 3 = 18 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Estimated 0.8 mm high-flow starting values, not manufacturer-calibrated. Flow ratio and pressure advance use this diameter's standard values times the material's 0.4 mm HF/standard ratio from snorca/main b1831e5dcb. Temperature uses the 0.4 mm HF-standard difference. Retraction and cooling remain diameter-specific. Volumetric speed ceiling: 6 mm^3/s, from Snorca standard preset Snapmaker PVA @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ], "filament_max_volumetric_speed": [ - "18" + "6" ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPE @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPE @U1 0.4 High Flow nozzle.json index 4b03c0e63d..441562c8d7 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPE @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPE @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "21.6" + "7.2" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.2 x 3 = 21.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.2 mm^3/s, from local standard fallback preset Snapmaker TPE @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.4 High Flow nozzle.json index 130bba2045..1accbf432d 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.6 High Flow nozzle.json index d999f651f1..51edd1e01f 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.8 High Flow nozzle.json index b49d1d3a09..847f0ed8d5 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 90A @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "10.5" + "3.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 3.5 x 3 = 10.5 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.5 mm^3/s, from Snorca standard preset Snapmaker TPU 90A @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A @U1 0.4 High Flow nozzle.json index 55ba8da2db..391cec907f 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "9.6" + "3.2" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 3.2 x 3 = 9.6 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 3.2 mm^3/s, from local standard fallback preset Snapmaker TPU 95A @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.4 High Flow nozzle.json index 461dcf6e69..0b0d178f90 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "27" + "9" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 9 x 3 = 27 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 9 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.6 High Flow nozzle.json index 416cfe0097..887c94ee7b 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "36" + "12" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 12 x 3 = 36 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 12 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.8 High Flow nozzle.json index 9971dabbf2..cb976d3246 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU 95A HF @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "48" + "16" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 16 x 3 = 48 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 16 mm^3/s, from Snorca standard preset Snapmaker TPU 95A HF @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.4 High Flow nozzle.json index 48d709b12d..afaefa2460 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "8.4" + "10.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2.8 x 3 = 8.4 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.4 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.6 High Flow nozzle.json index 8af4584d0a..00dd85f773 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "8.4" + "10.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2.8 x 3 = 8.4 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.6 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.8 High Flow nozzle.json index 6009f90585..cb7d2fa74f 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "8.4" + "10.5" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 2.8 x 3 = 8.4 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 10.5 mm^3/s, from Snorca standard preset Snapmaker TPU @U1 0.8 nozzle (snorca/main b1831e5dcb). No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.4 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.4 High Flow nozzle.json index d34d28c7b5..3118864459 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.4 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.4 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.4 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.8" + "7.6" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.6 x 3 = 22.8 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.6 mm^3/s, from local standard fallback preset Snapmaker TPU High-Flow @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.6 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.6 High Flow nozzle.json index 34cf3796f5..0c0a988c82 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.6 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.6 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.6 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.8" + "7.6" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.6 x 3 = 22.8 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.6 mm^3/s, from local standard fallback preset Snapmaker TPU High-Flow @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] } diff --git a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.8 High Flow nozzle.json b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.8 High Flow nozzle.json index 9453bf939b..ed24acdd57 100644 --- a/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.8 High Flow nozzle.json +++ b/resources/profiles/Snapmaker/filament/Snapmaker TPU High-Flow @U1 0.8 High Flow nozzle.json @@ -9,9 +9,9 @@ "Snapmaker U1 (0.8 High Flow nozzle)" ], "filament_max_volumetric_speed": [ - "22.8" + "7.6" ], "filament_notes": [ - "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling is 3x the inherited non-HF value for this diameter: 7.6 x 3 = 22.8 mm^3/s. This is a configured ceiling, not measured nozzle throughput. Calibrate for your nozzle and filament." + "Other material settings are inherited from the matching standard-nozzle preset. Volumetric speed ceiling: 7.6 mm^3/s, from local standard fallback preset Snapmaker TPU High-Flow @U1; no matching Snorca U1 material/nozzle profile. No multiplier or cross-material extrapolation is applied. Calibrate for your nozzle and filament." ] }