mirror of
https://github.com/OrcaSlicer/OrcaSlicer.git
synced 2026-05-23 13:15:13 +00:00
Reduce size by Json Fromatting (#13163)
Reduce the size of current and new JSONs by standardising them with 1 tab indentation instead of 4 spaces. This effectively reduces the size by almost 20 MB. | Current | New | |---|---| | 85.2 Mib | 67 Mib | Used [JQ](https://jqlang.org/) `--tab` to automatically format every current JSON. > [!NOTE] > Some profiles had the arrays on the same line, but those created by Orca were in the standard format (each object below the previous one). In some cases, this increases the number of tabs due to the new lines, but the increase is negligible, and this way both the base profiles and those created by Orca maintain the same style.
This commit is contained in:
Ian Bassi
@@ -1,25 +1,25 @@
|
||||
{
|
||||
"type": "machine",
|
||||
"setting_id": "GM003",
|
||||
"name": "Artillery Sidewinder X1 0.4 nozzle",
|
||||
"from": "system",
|
||||
"instantiation": "true",
|
||||
"inherits": "fdm_machine_common",
|
||||
"printer_model": "Artillery Sidewinder X1",
|
||||
"default_print_profile": "0.20mm Standard @Artillery X1",
|
||||
"nozzle_diameter": [
|
||||
"0.4"
|
||||
],
|
||||
"bed_exclude_area": [
|
||||
"0x0"
|
||||
],
|
||||
"printable_area": [
|
||||
"0x0",
|
||||
"300x0",
|
||||
"300x300",
|
||||
"0x300"
|
||||
],
|
||||
"printable_height": "400",
|
||||
"type": "machine",
|
||||
"setting_id": "GM003",
|
||||
"name": "Artillery Sidewinder X1 0.4 nozzle",
|
||||
"from": "system",
|
||||
"instantiation": "true",
|
||||
"inherits": "fdm_machine_common",
|
||||
"printer_model": "Artillery Sidewinder X1",
|
||||
"default_print_profile": "0.20mm Standard @Artillery X1",
|
||||
"nozzle_diameter": [
|
||||
"0.4"
|
||||
],
|
||||
"bed_exclude_area": [
|
||||
"0x0"
|
||||
],
|
||||
"printable_area": [
|
||||
"0x0",
|
||||
"300x0",
|
||||
"300x300",
|
||||
"0x300"
|
||||
],
|
||||
"printable_height": "400",
|
||||
"nozzle_type": "brass",
|
||||
"auxiliary_fan": "0",
|
||||
"machine_max_acceleration_extruding": [
|
||||
@@ -98,8 +98,8 @@
|
||||
"4"
|
||||
],
|
||||
"retraction_speed": [
|
||||
"35"
|
||||
],
|
||||
"35"
|
||||
],
|
||||
"deretraction_speed": [
|
||||
"0"
|
||||
],
|
||||
@@ -109,9 +109,9 @@
|
||||
"default_filament_profile": [
|
||||
"Artillery Generic PLA"
|
||||
],
|
||||
"machine_start_gcode": "; Initial setups\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Set the heating\nM190 S[bed_temperature_initial_layer_single] ; wait for bed to heat up\nM104 S[nozzle_temperature_initial_layer] ; start nozzle heating but don't wait\n\n; Home\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG28 ; home all axes\nG1 X3 Y3 F5000 ; move to corner of the bed to avoid ooze over centre\n\n; Wait for final heating\nM109 S[nozzle_temperature_initial_layer] ; wait for the nozzle to heat up\nM190 S[bed_temperature_initial_layer_single] ; wait for the bed to heat up\n\n; Return to prime position, Prime line routine\nG92 E0 ; Reset Extruder\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG1 X10 Y.5 Z0.25 F5000.0 ; Move to start position\nG1 X100 Y.5 Z0.25 F1500.0 E15 ; Draw the first line\nG1 X100 Y.2 Z0.25 F5000.0 ; Move to side a little\nG1 X10 Y.2 Z0.25 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nM221 S{if layer_height<0.075}100{else}95{endif}",
|
||||
"machine_end_gcode": "G4 ; wait\nG92 E0 ; prepare to retract\nG1 E-0.5 F3000; retract to avoid stringing\n\n; Anti-stringing end wiggle\nG91 ; use relative coordinates\nG1 X1 Y1 F1200\n\n; Raise nozzle and present bed\n{if layer_z < printable_height}G1 Z{z_offset+min(layer_z+120, printable_height)}{endif} ; Move print head up\nG90 ; use absolute coordinates\n\n; Reset print setting overrides\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Shut down printer\nM106 S0 ; turn-off fan\nM104 S0 ; turn-off hotend\nM140 S0 ; turn-off bed\nM150 P0 ; turn off led\nM85 S0 ; deactivate idle timeout\nM84 ; disable motors\n",
|
||||
"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
|
||||
"machine_start_gcode": "; Initial setups\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Set the heating\nM190 S[bed_temperature_initial_layer_single] ; wait for bed to heat up\nM104 S[nozzle_temperature_initial_layer] ; start nozzle heating but don't wait\n\n; Home\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG28 ; home all axes\nG1 X3 Y3 F5000 ; move to corner of the bed to avoid ooze over centre\n\n; Wait for final heating\nM109 S[nozzle_temperature_initial_layer] ; wait for the nozzle to heat up\nM190 S[bed_temperature_initial_layer_single] ; wait for the bed to heat up\n\n; Return to prime position, Prime line routine\nG92 E0 ; Reset Extruder\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG1 X10 Y.5 Z0.25 F5000.0 ; Move to start position\nG1 X100 Y.5 Z0.25 F1500.0 E15 ; Draw the first line\nG1 X100 Y.2 Z0.25 F5000.0 ; Move to side a little\nG1 X10 Y.2 Z0.25 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nM221 S{if layer_height<0.075}100{else}95{endif}",
|
||||
"machine_end_gcode": "G4 ; wait\nG92 E0 ; prepare to retract\nG1 E-0.5 F3000; retract to avoid stringing\n\n; Anti-stringing end wiggle\nG91 ; use relative coordinates\nG1 X1 Y1 F1200\n\n; Raise nozzle and present bed\n{if layer_z < printable_height}G1 Z{z_offset+min(layer_z+120, printable_height)}{endif} ; Move print head up\nG90 ; use absolute coordinates\n\n; Reset print setting overrides\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Shut down printer\nM106 S0 ; turn-off fan\nM104 S0 ; turn-off hotend\nM140 S0 ; turn-off bed\nM150 P0 ; turn off led\nM85 S0 ; deactivate idle timeout\nM84 ; disable motors\n",
|
||||
"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
|
||||
"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
|
||||
"scan_first_layer": "0"
|
||||
"scan_first_layer": "0"
|
||||
}
|
||||
|
||||
Reference in New Issue
Block a user