new feature translation

localization/i18n/zh_CN/OrcaSlicer_zh_CN.po

@@ -6,7 +6,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Slic3rPE\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2024-10-27 23:05+0800\n"
+"POT-Creation-Date: 2024-12-01 08:07+0100\n"
 "PO-Revision-Date: 2024-07-28 07:12+0000\n"
 "Last-Translator: Handle <mail@bysb.net>\n"
 "Language-Team: \n"
@@ -4229,7 +4229,7 @@ msgstr "体积："
 msgid "Size:"
 msgstr "尺寸："
 
-#, c-format, boost-format
+#, boost-format
 msgid ""
 "Conflicts of gcode paths have been found at layer %d, z = %.2lf mm. Please "
 "separate the conflicted objects farther (%s <-> %s)."
@@ -7315,8 +7315,8 @@ msgstr ""
 msgid ""
 "When recording timelapse without toolhead, it is recommended to add a "
 "\"Timelapse Wipe Tower\" \n"
-"by right-click the empty position of build plate and choose \"Add Primitive"
-"\"->\"Timelapse Wipe Tower\"."
+"by right-click the empty position of build plate and choose \"Add "
+"Primitive\"->\"Timelapse Wipe Tower\"."
 msgstr ""
 "在录制无工具头延时摄影视频时，建议添加“延时摄影擦料塔”\n"
 "右键单击打印板的空白位置，选择“添加标准模型”->“延时摄影擦料塔”。"
@@ -9592,7 +9592,6 @@ msgstr ""
 "值0表示在每个偶数层上都启用反转。\n"
 "当未启用检测悬垂时，此选项将被忽略，反转将在每个偶数层上发生。"
 
-
 msgid "Classic mode"
 msgstr "经典模式"
 
@@ -10878,10 +10877,10 @@ msgstr "满速风扇在"
 
 msgid ""
 "Fan speed will be ramped up linearly from zero at layer "
-"\"close_fan_the_first_x_layers\" to maximum at layer \"full_fan_speed_layer"
-"\". \"full_fan_speed_layer\" will be ignored if lower than "
-"\"close_fan_the_first_x_layers\", in which case the fan will be running at "
-"maximum allowed speed at layer \"close_fan_the_first_x_layers\" + 1."
+"\"close_fan_the_first_x_layers\" to maximum at layer "
+"\"full_fan_speed_layer\". \"full_fan_speed_layer\" will be ignored if lower "
+"than \"close_fan_the_first_x_layers\", in which case the fan will be running "
+"at maximum allowed speed at layer \"close_fan_the_first_x_layers\" + 1."
 msgstr ""
 "风扇速度将从“禁用第一层”的零线性上升到“全风扇速度层”的最大。如果低于“禁用风扇"
 "第一层”，则“全风扇速度第一层”将被忽略，在这种情况下，风扇将在“禁用风扇第一"
@@ -11883,6 +11882,14 @@ msgstr "换层时回抽"
 msgid "Force a retraction when changes layer"
 msgstr "强制在换层时回抽。"
 
+msgid "Retract on top layer"
+msgstr ""
+
+msgid ""
+"Force a retraction on top layer. Disabling could prevent clog on very slow "
+"patterns with small movements, like Hilbert curve"
+msgstr ""
+
 msgid "Retraction Length"
 msgstr "回抽长度"
 
@@ -12874,8 +12881,8 @@ msgstr "激活温度控制"
 
 msgid ""
 "Enable this option for automated chamber temperature control. This option "
-"activates the emitting of an M191 command before the \"machine_start_gcode"
-"\"\n"
+"activates the emitting of an M191 command before the "
+"\"machine_start_gcode\"\n"
 " which sets the chamber temperature and waits until it is reached. In "
 "addition, it emits an M141 command at the end of the print to turn off the "
 "chamber heater, if present. \n"
@@ -14713,8 +14720,8 @@ msgstr ""
 "你想重写预设吗"
 
 msgid ""
-"We would rename the presets as \"Vendor Type Serial @printer you selected"
-"\". \n"
+"We would rename the presets as \"Vendor Type Serial @printer you "
+"selected\". \n"
 "To add preset for more printers, Please go to printer selection"
 msgstr ""
 "我们将会把预设重命名为“供应商类型名 @ 您选择的打印机”\n"
@@ -16440,8 +16447,8 @@ msgstr ""
 #~ msgstr "无稀疏层（实验）"
 
 #~ msgid ""
-#~ "We would rename the presets as \"Vendor Type Serial @printer you selected"
-#~ "\". \n"
+#~ "We would rename the presets as \"Vendor Type Serial @printer you "
+#~ "selected\". \n"
 #~ "To add preset for more prinetrs, Please go to printer selection"
 #~ msgstr ""
 #~ "我们会将预设重命名为“供应商 类型 系列 @您选择的打印机”。\n"